IronDocuments.deOriginaltextRevised EnglishDeutschAtlasFormen & DetailsObjektkatalogTabellenFragen / SearchForschungsprojekt
Englische Neubearbeitung · vollständiger erster Entwurf

Iron Documents

Interdisciplinary studies on the technology of late medieval European plate armour production between 1350 and 1500

Der erste sprachliche Redaktionsdurchgang ist vollständig: Kapitel 1–9, Vor- und Schlussteile sowie Fußnoten. Erfasst sind 224 nicht leere PDF-Seiten. Bibliografische Angaben und Quellenzitate bleiben erhalten. Die Fassung ist zur Autorenkorrektur bereit; sie ist noch nicht fachlich freigegeben. Die Fassung bewahrt den Forschungsstand der Dissertation. Fachliche Unklarheiten und Ergänzungen stehen beim jeweiligen Abschnitt.

Opening material

PDF-S. 1–5 · Sprachlich überarbeitet · Entwurf

Title and dedication

Iron Documents

Interdisciplinary studies on the technology of late medieval European plate armour production between 1350 and 1500

Matthias Goll

Für Theo, den selbstlosen Sinnstifter…
Original dedication, retained in German.
Originalwortlaut vergleichen
Iron Documents



Iron Documents 



 



Interdisciplinary studies on the technology of late medieval European plate armour 



production between 1350 and 1500 



 



Matthias Goll



Für Theo, den selbstlosen Sinnstifter…
PDF-S. 7 · Sprachlich überarbeitet · Entwurf

Submission and funding

This dissertation was submitted by Matthias Goll to the Faculty of Philosophy at Heidelberg University on 11 July 2013 under the title “Interdisciplinary studies on the technology of late medieval European plate armour production between 1350 and 1500”.

The research project was generously funded by the Gerda-Henkel-Stiftung, Düsseldorf.

Redaktionelle Hinweise · 1
  • Datumswiderspruch in der Quelle: Hier steht 11. Juli 2013, im Vorwort 15. Juli 2013. Beide Angaben vorerst erhalten; vom Autor zu klären.
Originalwortlaut vergleichen
 



 



This document has been handed to the Philosophical Faculty of the University of 



Heidelberg as the PhD-Thesis of Matthias Goll on July 11th 2013. The original title 



was:  



“Interdisciplinary studies on the technology of late medieval European plate armour 



production between 1350 and 1500” 



 



 



 



 



 



 



 



 



 



 



 



 



 



 



 



The research project was generously funded by the Gerda-Henkel-Stiftung Düsseldorf. 
PDF-S. 9 · Sprachlich überarbeitet · Entwurf

Accessing the references

The references are linked to files supplied with the dissertation. When the text is opened on a computer with the original folder structure intact, a reference can be opened by clicking its filename in square brackets, for example [ref_arm_1] PDF.

Readers of the printed edition can locate the same files using their computer’s file manager. The filenames indicate where the references are stored: to open [ref_arm_1] PDF, for example, open the “ref” folder, then “ref_arm”, and then the file “ref_arm_1”.

Redaktionelle Hinweise · 1
  • Diese Anleitung beschreibt weiterhin die ursprüngliche Veröffentlichung mit ihrer Ordnerstruktur. Der neue HTML-Leser verwendet eigene Verweise; fehlende lokale Referenzkopien dürfen nicht als verfügbar ausgegeben werden.
Originalwortlaut vergleichen
 



 



How to access the quoted references 



The author tried to ease the reader’s handling of the many references given in the text. The 



text-document opened on your PC within the provided folder -structure will allow the 



opening of the  reference-links via clicking on the file-names written in brackets (e. g. 



[ref_arm_1]).  



When reading the print-version, please open the files in the explorer of your computer. The 



file-names in the text will guide you to the storage location of the concerned reference (e. g. 



for opening [ref_arm_1] first go to the folder “ref”, then to the sub-folder “ref_arm” and then 



click on the file “ref_arm_1”). 



 
PDF-S. 11 · Sprachlich überarbeitet · Entwurf

Abbreviations

  • AMI — Askeri Müze, Istanbul, Turkey
  • BAM — Bayerisches Armeemuseum (the original list gives Munich; the acknowledgements identify Ingolstadt), Germany
  • BMA — Burgmuseum Altena, Altena, Germany
  • BNM — Bayerisches Nationalmuseum, Munich, Germany
  • CH — Churburg Armoury, Schluderns, Italy
  • DHM — Deutsches Historisches Museum, Berlin, Germany
  • DIA — Detroit Institute of Arts, Detroit, United States
  • DNM — Danish National Museum, Copenhagen, Denmark
  • ESRF — European Synchrotron Radiation Facility, Grenoble, France
  • HJRK — Hofjagd- und Rüstkammer, Vienna, Austria
  • KIT — Karlsruhe Institute of Technology, Karlsruhe, Germany
  • MDA — Musée de l’Armée, Paris, France
  • MET — Metropolitan Museum of Art, New York, United States
  • MLM — Museo Luigi Marzoli, Brescia, Italy
  • MNMB — Magyar Nemzeti Museum, Budapest, Hungary
  • MNMC — Musée National du Moyen Âge (Musée de Cluny), Paris, France
  • RA — Royal Armouries, Leeds, United Kingdom
  • RAM — Real Armería, Madrid, Spain
  • SKD — Staatliche Kunstsammlungen, Dresden, Germany
  • SMM — Stadtmuseum München, Munich, Germany
  • SNZ — Schweizerisches Nationalmuseum, Zurich, Switzerland
  • WM — Wien Museum, Vienna, Austria
Redaktionelle Hinweise · 1
  • BAM: Widerspruch zwischen München im Original-Abkürzungsverzeichnis und Ingolstadt in der Danksagung sichtbar gemacht. Historische Museumsnamen ansonsten beibehalten; keine Neuzuordnung von Objekt-IDs.
Originalwortlaut vergleichen
List of abbreviations 



AMI Askeri Müze, Istanbul, Turkey 



BAM Bayerisches Armeemuseum, Munich, Germany 



BMA Burgmuseum Altena, Altena, Germany 



BNM Bayerisches Nationalmuseum, Munich, Germany 



CH Churburg Armoury, Schluderns, Italy 



DHM Deutsches Historisches Museum, Berlin, Germany 



DIA Detroit Institute of Arts, Detroit, United States 



DNM Danish National Museum, Kopenhagen, Danmark 



ESRF European Synchrotron Radiation Facility, Grenoble, France 



HJRK Hofjagd- und Rüstkammer, Vienna, Austria 



KIT Karlsruhe Institute of Technology, Karlsruhe, Germany 



MDA Musée del’Armee, Paris, France 



MET Metropolitan Museum of Art, New York, United States 



MLM Museo Luigi Marzoli, Brescia, Italy 



MNMB Magyar Nemzeti Museum, Budapest, Hungary 



MNMC Museé Nacional du Moyen Age (Museé Cluny), Paris, France 



RA Royal Armouries, Leeds, GB 



RAM Réal Armeria, Madrid, Spain 



SKD Staatliche Kunstsammlungen, Dresden, Germany 



SMM Stadtmuseum München, Munich, Germany 



SNZ Schweizerisches Nationalmuseum, Zurich, Switzerland 



WM Wien Museum, Vienna, Austria
PDF-S. 13 · Sprachlich überarbeitet · Entwurf

Abstract

This study investigates the production of late medieval European plate armour for use in the field. It begins with a database of several thousand surviving objects, which provides the basis for grouping and classifying armour according to its typological and technological features. To make the subject more accessible, the study establishes a clear, standardised terminology and typology for the different forms of armour.

A brief technological history of plate armour introduces the subject. This is followed by an extensive examination, definition and comparison of individual features and the methods used to produce them. A short account of the principal crafts supplying components to armourers places their work in a broader context. The study then addresses authenticity: a survey of the history of armour preservation introduces metallurgical and art-historical approaches, followed by new observations on armour production and proposals for further research.

Examining a large body of surviving plate armour proved an effective way of identifying common patterns in late medieval production in central Europe. Standardised data collection and systematic organisation make it possible to compare objects on a large scale and to identify shared features. Drawings prepared specifically for this study bring together the results of detailed observation. Numerous common or “standardised” features emerge. As in masonry, painting and goldsmithing, the evidence strongly suggests the existence of groups associated with particular hands or workshops.

For the first time, ridges, rivets and washers, applied fittings, surface decoration, turned edges, marks, dimensions, weights and fastening methods are classified and used to propose reconstructions of historical techniques and their development. The study also offers the first discussion of how iron plate may have been made in the Middle Ages using a water-powered hammer. Written and visual sources, together with surviving craft traditions, provide the basis for describing methods of mass-producing armour towards the end of the period under consideration.

Many questions nevertheless remain unresolved. In most cases, an object cannot be identified conclusively as either an original or a reproduction. Further research is needed to improve our understanding of this difficult subject. The findings presented here provide a sound basis for future work on late medieval plate armour across the relevant disciplines.

Redaktionelle Hinweise · 1
  • Forschungsstand und Erstmaligkeitsansprüche als Aussagen der Dissertation von 2013/2014 erhalten; nicht als 2026 neu geprüfte Aussagen behandeln. „Applications“ kontextbezogen als „applied fittings“ wiedergegeben.
Originalwortlaut vergleichen
 



 



Abstract 



The purpose of this study is to find out details on the production of late medieval European 



plate-armour for the field -use. Therefore, the author first collected thousands of extant 



objects in a database. With this stock of data he then was able to cluster and to structure the 



armour parts by various typological and technological aspects. To ease the access to the 



topic, the author defined an understandable and standardized terminology and typology for 



the different variations of armour parts.  



The author tried to prime the reader on the topic of armour production by summarizing the 



history of plate armour under technological aspects. This  was followed by a large scale 



observation, definition and comparison of various armour -features and their making. To 



complete the picture, the main crafts that supplied add -on parts for the armourer’s products 



were shortly described. The author then enter ed the problematic topic of the authenticity 



question. After a short abstract on the history of armour preservation, metallurgical and art-



based approaches to the problem of authenticity were introduced and new aspects on armour 



making as well as suggestions for future approaches were presented. 



The examination of a huge number of extant plate armour pieces proofed to be a practical 



way to find new common structures in the late medieval armour production in central 



Europe. The development of a standardized data acquisition and its systematic organization 



enables large scale comparisons that bring new evidence for common features of extant 



armour pieces. Many drawings, made especially for this study on the basis of the collected 



data, combine the results of the detail observation in a concrete way. Numerous common or 



“standardized” features were revealed. Similar to schools of masonry, of painting or of 



goldsmithing also for the armourer’s art the existence of certain hand or workshop circles 



can clearly be presumed. 



For the first time, ridges, rivets and washers, applications, surface decorations, turned edges, 



marks, measurements, weights and different fastening techniques were classified and used 



to suggest reconstructions of the historical technology and its development. The explanation 



on how iron plate material might have been made in the Middle Ages by means of a water 



powered hammer is discussed for the first time. On the basis of written and depicting sources, 



but also by ongoing traditions, methods for the mass production of armour by the end of the 



considered period were described. 



This study also shows that a lot of questions remain not finally solved. A final decision on 



an item to be genuine or reproduced can for the most cases not be made. Further research 



has to be carried out to enhance our knowledge on this delicate issue. The findings of this 



study do certainly deliver a stable basis for any future approach by any discipline to the topic 



of late medieval plate armour. 
PDF-S. 15 · Sprachlich überarbeitet · Entwurf

Preface

Before turning to the subject itself, a few words on how this project began. It is unusual for a student of European art history to take up the technology of late medieval plate armour. My decision grew out of a longstanding personal interest. Every year, my hometown of Bretten commemorates its relief after a two-week siege in the summer of 1504. Local history enthusiasts gather in reconstructed late medieval dress, stepping back into the past for a weekend. Since 1999, I have belonged to one of the groups representing a Landsknecht unit of the late Middle Ages.

By 2002, I had become dissatisfied with the poor reproductions of equipment that were so common in the reenactment scene. I began reconstructing the equipment of a late medieval mercenary from contemporary sources: clothing, buckles, shoes, purses, weapons and, eventually, armour. During this work I met Peter Müller, a young armourer who had already made a few simple pieces. In 2003, he made reproductions of a surviving helmet and breastplate, both fitted to me. Our shared enthusiasm for armour developed into a friendship, and Peter eventually moved his workshop into the old stable behind my house.

We had always had particular respect for the craftsmanship of the segmented, articulated hand protection made during the final two decades of the fifteenth century. One afternoon, a wager was made that I would be unable to reproduce an example in the Wallace Collection in London. I took up the challenge and achieved a result that was, more or less, satisfactory.

The experience left me eager to learn more about the details visible on surviving armour. In 2004, after completing his doctorate in mechanical engineering, Peter Müller made armour-making his principal occupation. I learned a great deal in his workshop and financed a substantial part of my studies by making armour, clothing and accessories for private and public clients.

This work always required research into surviving medieval objects, paintings, sculpture and other sources. The search often came to an abrupt halt: most publications offered only a single image of the object concerned. Information about its complete form and construction was difficult to find. Much of the literature was old, rarely available in public libraries and often prohibitively expensive on the second-hand market.

My broader interest in the past led me to study art history in Heidelberg in 2003. There I learned how to investigate historical subjects systematically. As a consequence, the armour made in Peter Müller’s workshop became progressively closer to the originals. I increasingly wanted to document what we had learned.

In 2008, my art-history professor, Matthias Untermann, encouraged me to write my Magister thesis on late medieval plate armour.1 I found the work so rewarding, and saw so many possibilities for further research, that after graduating I decided to pursue a doctorate on the same subject, with a stronger emphasis on production technology.

This book was submitted to the Faculty of Philosophy at Heidelberg University on 15 July 2013 as a doctoral dissertation entitled “Interdisciplinary studies on the technology of late medieval European plate armour production between 1350 and 1500”.

The study was generously funded by the Gerda-Henkel-Stiftung, Düsseldorf, Germany.

Redaktionelle Hinweise · 2
  • Im autobiografischen Vorwort „the author“ durch die erste Person ersetzt; eine redaktionelle Stilentscheidung, keine neue Tatsachenbehauptung.
  • Datum 15. Juli 2013 aus dem Vorwort beibehalten; die vorgelagerte Abgabenotiz nennt abweichend den 11. Juli 2013.
Originalwortlaut vergleichen
 



 



Preface 



Before entering medias res: It is of course not common that a student of European art history 



comes to study the technology of late medieval plate armour. The reason for this decision is 



very much based in the author’s private interest and hobby. His hometown , the city of  



Bretten, each year celebrates its rescue from a two week siege, laid upon the town walls in 



the summer of 1504. Friends of the local history come together and dress in reproduced late 



medieval costumes – travelling for one weekend into the past. Since 1999 the aut hor is a 



member of one of these groups which try to resemble one of the Landsknecht units of the 



late Middle Ages. In 2002 he had enough of the omnipresent bad equipment -reproductions 



in the scene. He started to reconstruct the equipment of a late medieval mercenary according 



to contemporary sources: clothes, buckles, shoes, purses, weapons and finally also armour. 



On this course he learned to know Peter Müller, a young armourer who had yet made a few 



simple armour pieces. In 2003 the latter made reproducti ons of an extant helmet and a 



breastplate made to measure for the author. The two  armour-freaks became friends and 



finally Peter Müller moved his workshop in the old stable behind the author’s house. The 



two always had the greatest respect for the making o f the segmented and articulated hand -



protections of the last two decades of the 15 th century. One afternoon a bet was set that the 



author would not be able to reproduce a hand-protection preserved in the Wallace Collection 



in London. The author tried and succeeded more or less satisfactorily.  



From then on he had tasted blood and he wanted to know more about all the details 



observable at extant armour pieces. In 2004 Peter Müller started his armour workshop as his 



main business, after having graduated as a doctor of mechanical engineering. In his 



workshop the author learned a lot about armour making and financed a huge part of his 



studies with the making of armour, dress and accessories for private and public clients.  



For all this work it was always necessary to research extant medieval examples, depictions, 



statues and other sources. V ery often the necessary studies came to an abrupt end, as almost 



all the publications showed only one image of the item of interest. Details about the full 



shape and the construction were very hard to find. Literature was antiquated and thus rarely 



to be found in public libraries and often hard to pay on antique sales. 



Deriving from the general interest in the past, the author went to study art history  in 



Heidelberg in 2003. There he got the experience on how to scientifically research a historical 



topic, as a side effect the quality of the armour made in Peter Müller’s workshop became 



permanently better and closer to the original. The will for the documentation of the gained 



experience was growing.  



Finally, the author’s Professor in art history, Matthias Untermann, in 2008 encouraged him 



to write his Magister -thesis on the topic of late medieval plate armour 1. This turned out to 



be so much fun and a field for much more research so – after having graduated – the author 



decided to also write his PhD -thesis on this topic, now with a stronger focus on the 



technology of armour making.  



On July 15 th 2013 t he present book was handed in to the Philosophical Faculty at the 



University of Heidelberg as a PhD thesis with the title “ Interdisciplinary studies on the 



technology of late medieval European plate armour production between 1350 and 1500”. 



 



This study was generously funded by the Gerda-Henkel-Stiftung, Düsseldorf, 



Germany. 



                                                 



1 For the published version of this thesis see: Goll (2009). 
PDF-S. 17–20 · Sprachlich überarbeitet · Entwurf

Contents

Redaktionelle Hinweise · 1
  • Das Inhaltsverzeichnis wird aus den überarbeiteten Abschnittstiteln erzeugt. Originale Gliederungsnummern und separate Originalverweise bleiben erhalten; die HTML-Fassung hat keine neue Druckpagination.
Originalwortlaut vergleichen
Index 



1 Introduction ................................................................................................... 29 



2 Terminology and typology of plate armour ................................................ 34 



2.1 Present-day’s terminology and typology ................................................. 34 



2.2 Suggestions for standardized definitions ................................................. 40 



2.2.1 Textile (not in the focus of this study) ......................................... 41 



2.2.2 Leather (not in the focus of this study) ........................................ 41 



2.2.3 Ring-armour (not in the focus of this study) ................................ 41 



2.2.4 Segmented (not in the focus of this study) ................................... 42 



2.2.5 Plate .............................................................................................. 42 



3 A brief history of plate armour from a technological point of view ......... 52 



3.1 Arm-protection......................................................................................... 53 



3.1.1 Shoulder ....................................................................................... 53 



3.1.2 Armpit .......................................................................................... 54 



3.1.3 Upper arm .................................................................................... 54 



3.1.4 Elbow ........................................................................................... 54 



3.1.5 Lower arm .................................................................................... 54 



3.1.6 Systems ........................................................................................ 55 



3.2 Hand-protection ....................................................................................... 56 



3.2.1 Finger and thumb protection ........................................................ 58 



3.3 Head-protection ....................................................................................... 59 



3.3.1 Type-I ........................................................................................... 59 



3.3.2 Type-II .......................................................................................... 60 



3.3.3 Type-III ........................................................................................ 60 



3.3.4 Type-IV ........................................................................................ 61 



3.3.5 Type-V ......................................................................................... 62 



3.3.6 Type-VI ........................................................................................ 62 



3.3.7 Type-VII ....................................................................................... 63 



3.3.8 Type-VIII ..................................................................................... 63 



3.3.9 A noteworthy, not preserved type ................................................ 64 



3.4 Leg-protection .......................................................................................... 64 



3.4.1 Knee ............................................................................................. 64 



3.4.2 Lower leg ..................................................................................... 65 



3.4.3 Upper leg ...................................................................................... 65 



3.4.4 Systems ........................................................................................ 66 



3.4.5 Leg foot ........................................................................................ 66 



3.5 Neck-protection ....................................................................................... 66 



3.6 Torso-protection ....................................................................................... 67 



3.6.1 Torso front .................................................................................... 67



3.6.2 Torso back .................................................................................... 69 



3.6.3 Concerning torso front and back together .................................... 70 



3.6.4 Systems ........................................................................................ 71 



4 Summarizing technological features ........................................................... 72 



4.1 Metalwork on the plates ........................................................................... 74 



4.1.1 The general forming of plate armour ........................................... 74 



4.1.2 Turned or angled edges and riveted bars...................................... 75 



4.1.3 Embossing .................................................................................... 79 



4.1.4 Not-embossed plate decoration .................................................... 84 



4.2 Joints and applications ............................................................................. 89 



4.2.1 Rivets ........................................................................................... 89 



4.2.2 Washers ........................................................................................ 99 



4.2.3 Non-detachable joints ................................................................ 100 



4.2.4 Detachable joints ........................................................................ 102 



4.2.5 Body-fastenings ......................................................................... 107 



4.2.6 Applications ............................................................................... 117 



4.3 Dimensions ............................................................................................ 131 



4.3.1 Measurements ............................................................................ 131 



4.3.2 Weight ........................................................................................ 133 



4.3.3 Plate-thickness ........................................................................... 136 



4.4 The serial production of armour ............................................................ 141 



4.4.1 Type-V: “Chalcis barbuta” ......................................................... 145 



4.4.2 Type-II: “Chalcis closed helmet” ............................................... 146 



4.4.3 Type-V “Chalcis basinet-barbuta” ............................................. 148 



4.4.4 Type-VII “serial product” .......................................................... 149 



4.4.5 Central Europe ........................................................................... 152 



5 Supplying crafts .......................................................................................... 160 



5.1 Wire drawing ......................................................................................... 160 



5.2 Production of tools ................................................................................. 161 



5.3 Tailoring ................................................................................................. 161 



5.4 Etching ................................................................................................... 161 



5.5 Bellows .................................................................................................. 162 



5.6 Tanners ................................................................................................... 162 



5.7 Lace production ..................................................................................... 162 



6 The problem of authenticity ....................................................................... 164 



6.1 Notes on the history of armour preservation ......................................... 165 



6.1.1 The dynastic collection .............................................................. 166 



6.1.2 The arsenal ................................................................................. 167



6.1.3 Armour preserved in churches ................................................... 169 



6.1.4 The modern assembled collection .............................................. 169 



6.1.5 Mixed collections ....................................................................... 171 



6.2 Notes on the history of armour reproduction and restoration ................ 171 



6.2.1 Modern alterations ..................................................................... 175 



6.2.2 Historical recycling of armour parts .......................................... 176 



6.3 Preceding preoccupations with the general topic of authenticity .......... 177 



6.3.1 Archaeologist’s, art historian’s and connoisseur’s approaches .. 177 



7 The metallurgy of armour production ...................................................... 183 



7.1 The production of iron and steel ............................................................ 183 



7.1.1 Wrought-iron production ........................................................... 183 



7.1.2 Mild steel production ................................................................. 185 



7.2 The making of plates.............................................................................. 185 



7.3 Plate quality ........................................................................................... 189 



7.3.1 Turning iron into steel: Case carburizing – case hardening ....... 192 



7.4 Metallurgical testing .............................................................................. 193 



7.4.1 Quality testing methods ............................................................. 193 



7.4.2 X-ray based imaging methods.................................................... 196 



7.4.3 The authenticity testing of armour ............................................. 197 



8 Suggestions for new approaches to the mapping of plate armour ......... 202 



8.1 Dating reference ..................................................................................... 203 



8.2 Mapping with the help of marks ............................................................ 204 



8.3 New recognitions on marks ................................................................... 207 



8.4 Discussion of the possible genuine appearance of armour .................... 209 



8.5 Authenticity discussion of single chosen objects .................................. 211 



8.5.1 The “Sigmaringen” armour in Detroit ....................................... 211 



8.5.2 V arious neck-protections ............................................................ 212 



8.5.3 A suit in the BMA ...................................................................... 212 



8.5.4 A type-VIII helmet in the Royal Armouries............................... 213 



8.5.5 A type-II helmet in the Royal Armouries ................................... 214 



8.5.6 An electro-plated helmet in Delft............................................... 217 



8.5.7 A recently sold helmet of type-VII ............................................ 217 



8.6 Ideas for new approaches ....................................................................... 219 



8.6.1 Perspectives for non-destructive metallurgical testing: Synchrotron 



Radiation Computed Laminography .......................................... 219 



8.6.2 An appeal to all interested scientists .......................................... 223 



9 Summary ...................................................................................................... 225 



Appendix........................................................................................................... 227



Acknowledgements .......................................................................................... 228 



References ......................................................................................................... 231

1 Introduction

S. 29–33 · Sprachlich überarbeitet · Entwurf

1 Introduction

What comes to mind when you think of plate armour? Perhaps knights fighting on horseback, the weight they had to carry, the apparent restriction of their movements, or the difficulty of breathing inside a helmet. You may also recall a suit of armour seen in a museum.

Armour is far more varied than these images suggest. Like clothing, it changed with fashion, purpose, period and region. Armourers were often in direct contact with the rulers of their day, and many enjoyed personal esteem comparable to that of the celebrated artists whose names are still familiar to us.

Since armour ceased to be used, however, the surviving material and its documentation have become dispersed and disordered. Armouries, suits and even individual objects have been broken up; components have been lost; formerly associated pieces have entered different collections; objects have been repaired; and missing components or entire suits have been reproduced. Since the late eighteenth century, collectors and researchers have sought to reconstruct these relationships. Archival records identify many armourers, their families and their places of work. Some record prices or name customers. An object may be attributed to a maker if it bears an identifiable personal or workshop mark. A town’s quality-control stamp may also suggest a place of production. Some owners marked their possessions with their own symbols.

The development of armour’s forms and its place in art history have been extensively studied over the past two centuries, leaving relatively few additions and corrections to be expected. The same cannot be said of production technology. No late medieval account of the practical methods of armour-making appears to survive. This may help explain why the subject has remained largely unexplored.

One of the few major works on the subject, and still an unrivalled point of reference, is Charles Ffoulkes’s The Armourer and His Craft, published in the early twentieth century.2 Ffoulkes provides a valuable overview, but does not systematically classify individual features or explain how those found on surviving armour were made. His discussion remains general and is now outdated in several respects. About a century later, Brian R. Price published a practical guide to reproducing armour.3 Its purpose is to assist modern makers rather than to develop the scholarly understanding of historical production. Over the past thirty-five years, Alan Williams has made important contributions to the study of armour materials.4 Historical techniques of surface decoration have also been discussed in other publications.5

Yet the development of technological features has not been studied in comparable detail. Many features visible on surviving armour remain largely unexplored, despite their potential to answer questions about the objects and the almost vanished craft that produced them. Their study is also indispensable to distinguishing original objects from high-quality reproductions.

One reason for this neglect may be disciplinary uncertainty. Which field is best equipped to investigate armour-making? Art history? Or archaeology, with its concern for the material culture of the past?

The study of armour requires the methods of both. Most surviving objects have remained above ground: they were neither lost nor discarded and consequently lack the archaeological deposits that might help establish a date. Nevertheless, many useful methods are archaeological. Armourers left traces of their skills and of contemporary tastes in the objects they made. These can be classified much as archaeologists classify diagnostic features of pottery.

Armour was also more than protective equipment. It could be sculpture, clothing, a defensive weapon and, in some cases, a surface for two-dimensional imagery. Art history has traditionally interpreted these aspects. Where written evidence is absent or incomplete, experimental archaeology may help answer practical questions. Although many such projects are now respected, the approach has not gained universal academic acceptance. The cost of reconstructing historical crafts also means that much published research remains theoretical.

No single discipline encompasses all the skills required to reconstruct and describe how historical objects were made. The history of technology has instead developed through interdisciplinary investigations of particular problems. Its contributors have included independent enthusiasts, engineers, historians, art historians and archaeologists, as well as specialists in fields such as philology.

The technological history of plate armour lies at the intersection of these disciplines and approaches. This study is itself an interdisciplinary project, proposing new ways of investigating the practical knowledge behind an almost forgotten art and craft.

The principal focus is central European production, since links with armour from other cultural regions appear marginal during the period considered. The ability of medieval, Renaissance and Baroque European craftspeople to make armour for the entire body from large plates was unique. Here, “central Europe” refers chiefly to northern Italy and the German-speaking lands. England, France and Spain also had important production centres from the second half of the fifteenth century onwards; their products are considered and compared with German and Italian examples wherever possible.

The period 1350–1500 encompasses the first major flowering of plate-armour production. Following the decline of the Roman Empire, helmets were the only armour objects occasionally made from large plates. The move towards covering the torso with larger plates becomes apparent in the mid-fourteenth century. Few earlier objects therefore offer suitable material for the technological comparisons pursued here.

The protective effectiveness of armour falls outside the scope of this study. Any investigation would have to account for numerous variables. Testing original objects is out of the question. Tests using reproductions would be meaningful only if the materials of both weapons and armour had been produced by historical methods. Penetration tests would then have to be repeated with different weapons, forces, angles of impact and supports beneath the armour. Even then, the results would apply only to the objects tested.

Both high- and low-quality weapons and armour were in use at the same time. Historical accounts of armoured men killed in battle already indicate one end of the possible range of results. The many who survived battles, including blows to the body, demonstrate the other. Outcomes could range from no injury to immediate death, with numerous intermediate results.

By the beginning of the fifteenth century, specialised armour was being made exclusively for the different forms of tournament combat. This remains an interesting and comparatively neglected field. Including it here would, however, have required the examination of several thousand additional objects, beyond the time available. Horse armour likewise falls outside the study. The same master armourers often made field armour, tournament armour and horse armour, leaving important questions for future research across these branches of the craft.

This project investigates recurring features of field armour, the development of ideas and the presence of features resembling standards from the earliest stages of armour-making. At the same time, it seeks to show the considerable scope for creativity and invention. Classifying the features of surviving armour may allow precise distinctions between makers, schools, regions and periods. The study also draws attention to how little is yet known and to questions that no single project can resolve.

Extensive archival research was not possible within this project. Published contemporary sources reveal little about production technology. Medieval depictions of armourers at work are rare and offer limited technical information. Practical accounts specifically devoted to armour-making were not written down; specialist knowledge was most probably transmitted orally to selected members of the next generation. This protected the experience of local armourers’ guilds from competitors in other towns and from unauthorised craftspeople.

Nevertheless, five groups of written sources are relevant: guild regulations, orders, payments, legal disputes, and accounts and inventories. Occasional technical details appear incidentally in these records. Questions they leave unanswered must be approached through the technological features of surviving objects. Understanding the processes that led from mined ore to an armoured fighter also requires later sources, evidence from other crafts, specialist knowledge and practical experience.

From the early nineteenth century, growing scholarly interest in the European Middle Ages was accompanied by increasing demand for historical armour. Supply was limited, prices rose, and a flourishing industry developed to reproduce arms and armour. Forgeries entered the market, while some reproductions came to be sold as originals after passing through successive owners. Today, distinguishing originals from reproductions can be extremely difficult in collections around the world.

Because this study relies on surviving objects, authenticity is fundamental to the discussion. Identified reproductions and questionable objects have therefore been deliberately included. Comparing their details with those of armour thought to be genuine may reveal new criteria for assessment without resorting to expensive or destructive scientific tests. The database permits detailed comparisons on a large scale between objects of secure and uncertain provenance, offering the prospect of greater clarity in this difficult field.

The materials with which armourers began their work remain uncertain: what semi-finished products did they use, where did they obtain them, and how had those products been made from ore? Answering these questions requires expertise in art history, archaeology, history, metalworking and the natural sciences, particularly metallurgy. Ironworking is an especially broad and difficult field. Its study is also relatively young, since iron was long regarded as unimportant to the history of art.

In the Middle Ages, iron was produced throughout the world apart from Australia, New Zealand and the American continents. It could be made by many methods, and the necessary raw materials were widely available. Old iron was frequently recycled and traded over long distances. These factors make the investigation of iron objects particularly complex.

The production of plate and its subsequent shaping into armour have received little attention. Many surviving examples of sixteenth-century arsenal armour are so similar that they appear to have been produced in series, probably through an organised division of labour.6 The historical development of mass production in plate and armour has not yet been investigated.

Armour was made for different social groups: noblemen, prosperous citizens and ordinary foot soldiers. Comparing the dimensions of surviving objects may help distinguish work made to measure from mass-produced equipment intended to fit a range of wearers. Art-historical research has concentrated chiefly on expensive, richly decorated armour; plain objects remain much less studied. Production centres existed across central, western and southern Europe, but unmarked objects usually leave both maker and place of production uncertain. Many may have come from less familiar centres.

Where documents or marks cannot establish provenance, technological features may offer another route. This first requires close observation and description of small details in a form that allows comparison between objects. A database of detailed photographs and associated information provides the foundation. Standardised nomenclature and typology are needed to make the material easier to evaluate.

Comparative features include marks, materials, surface structures, decoration, edges, ridges, washers, rivets, applied fittings and joints between plates. Dimensions, plate thicknesses and weights provide further evidence. Such comparisons may reveal previously unrecognised relationships and allow groups of objects to be defined.

The quantity of European plate armour surviving from 1350–1500 makes it difficult to investigate every aspect of production. Contemporary artworks also depict numerous lost forms and individual objects, which could be organised and compared in much the same way. A detailed survey of such depictions was beyond the scope of this project, although visual sources are described and used wherever they help interpret surviving armour.

Earlier studies have generally examined a single object or compared a small group. Their descriptions cannot readily serve as the basis for systematic comparison: neither language, terminology nor emphasis was standardised, and authors attended to constructional details in different ways. Many descriptions are primarily stylistic classifications rather than accounts of technological features.

High-quality photographs were therefore the most important working material for this study. Although many publications include illustrations, these rarely show sufficient detail. Only a few present several views of an object, and images of its interior are especially uncommon. Interior views are essential here. They reveal constructional features invisible from the outside, and the internal surface is also the surface most likely to remain relatively untouched after the armourer’s shaping work.

Approximately 1,300 objects were handled and photographed using equipment designed for the project. Each was recorded in about three to eight photographs from different angles. Most were measured, their marks were recorded by rubbings, and they received a brief initial examination. Some had to be removed from display and reinstalled afterwards. On certain days, more than twenty objects were examined, leaving little time for close study on site. Detailed analysis was carried out later from the records.

Time and financial constraints prevented visits to several collections. Most museums were receptive to this approach. Unfortunately, the curators of the RA, HJRK, RAM and MNMB did not support access to larger numbers of objects in their collections.

The approaches proposed here are not intended as fixed or universally unproblematic solutions. They leave considerable room for discussion, which will, it is hoped, advance the subject. The collected data and the system used to organise them may help uncover new relationships between documentary evidence and surviving objects.

Redaktionelle Hinweise · 2
  • Forschungsstand und Zeitangaben wie „over the past thirty-five years“ beziehen sich auf die Abfassung 2013/2014. Die Redaktion ist keine Aktualisierung der Forschungsliteratur.
  • Aussagen zur Geschichte der Eisenproduktion, zu fehlenden technischen Schriftquellen und zur institutionellen Zugänglichkeit bleiben Aussagen der historischen Dissertation und wurden hier nicht sachlich neu verifiziert.
Originalwortlaut vergleichen
 



29 



 



1 Introduction 



What comes to your mind when you think of plate armour?  



You probably see knights in fierce fights on horseback; you probably think of the 



considerable weight that the fighters have to bear and how inflexible they were in their 



motions, how difficult it must have been to breath and you may remember some suits of  



armour that you once have seen in a museum.  



Armour is much more than that. Armour is like clothing -fashion. It varied in style and 



construction throughout the ages, for different purpose and from region to region. Armourers 



were often in direct contact with the rulers of their times. Many of them were personally as 



much appreciated as their famous art-creating contemporaries that we still remember today. 



However, since the time of its use, what still exists of armour became disarranged – both 



physically and documentarily. Armouries and suits or even single items got torn apart, parts 



got lost, formerly associated pieces got into different collections, a lot got repaired and 



missing parts or whole suits were reproduced. Since the late 18 th century, collectors and 



researchers are trying to get things back in order. Archive material provides names and 



locations of many old master armourers and their families. Sometimes documents tell about 



the cost of armour, occasionally they tell us the names of customers. The master of an extant 



object might be identified if it bears an identified personal or a workshop’s mark. If the city, 



where the quality of the armour was tested, stamped the plate with its symbol, the production 



might also have been located there. Also some owners marked their items with their symbol. 



The morphological and the art-context genesis of armour has been researched and described 



sufficiently throughout the last 200 years. Only a few future additions and corrections are to 



be expected. Concerning the making of armour, nothing seems to have been written down in 



the late Middle Ages, at least nothing survived. This is probably one of the reasons why the 



technology of armour production still remains a virgin field of research. One of the few and 



still unrivaled publications on the topic is Charles Ffoulkes’ “The armourer and his craft” 2, 



written in the early 20th century. Ffoulkes provided for a good overview on the subject, while 



he did not classify and describe the making of certain features found on extant armour. The 



discussion remains rather general and at several points it is of course not up to date anymore. 



Brian R. Price3 wrote a code of practice for armour reproduction about a hundred years later. 



This book does not gain further academic ins ight on the topic, it is rather intended to guide 



modern reproducers in making armour. In the last 35 years Alan Williams 4 has carried out 



important research on the material quality of plate armour. In various other publications, 



discussions of the ancient techniques of surface-decoration have been included.5  



Nevertheless, in none of the preceding scholarly preoccupations with the topic of armour, 



the genesis of technological aspects has been studied in details. So far, many features 



observable at extant a rmour still remain undiscussed – despite their big potential for 



answering open questions on the artifacts themselves and on the ancient and almost vanished 



craft of armour-making. Furthermore, studying such features is indispensable for approaches 



to a differentiation between genuine items and high quality reproductions.  



                                                 



2  Ffoulkes (1912). 



3  Price et al. (2000). 



4  Most of the results are found comprehensively in: Williams (2003). 



5  E. g.: Thomas and Gamber (1976) p. 25-34. 







 



30 



 



The reason for this topic still remaining widely untouched might derive from a simple 



competence question: Which academic discipline is suited for researching this topic? Is it art 



history? Is it not archaeology that takes care of profane material cultures of the past?  



Studies on armour do certainly need the systematics and the tools of both disciplines. Most 



extant items were preserved “above ground”. They did not get lost or dumped and thus they 



were never covered by dirt and rubbish that could now help to support their dating. Anyway, 



some tools needed to research armour are actually those used by archaeologists. The 



armourers left some fingerprints of their skills and taste of their ow n times at the items – 



these can be classified like archaeologists classified significant features of ancient pottery.  



On the other hand, armour was not only made to fulfill a protective function: it is also artwork 



– sculpture, plastic, clothing, defensive weapon and in some cases even medium for the 



communication of 2 -dimensional images. Art history  is certainly the disc ipline that 



traditionally interprets all these aspects. Where written documents are missing or incomplete, 



“experimental archaeology” can help to answer open question. This discipline is – even 



though for many projects nowadays respected – academically still not widely accepted. For 



the sake of the usually high costs of experimentally reconstructing ancient crafts, most of 



the academic research publications only theoretically reconstruct ancient technologies. 



The discipline that would cover the necessary skills for the descriptive reconstruction of the 



making of historical artifacts does not exist as such. This “history of technologies” has so far 



always been written by interdisciplinary approaches to specific issues. The authors of 



preceding papers on histo rical technologies were often non -academic lays, engineers, 



historians, art historians or archaeologists. Different disciplines, like philology, delivered 



their part as well.  



The starting point for discussing the history of plate -armour technology is loca ted 



somewhere in this cloud of disciplines and approaches. This study presents an 



interdisciplinary research project of its own, starting with new ideas on how to get closer to 



the open questions on the technological exertion of a nearly forgotten art or craft. 



The focus of this study is exclusively on the central European plate armour production, as 



for the considered period the links to armour of other cultural regions seem to be marginal. 



The skills of the medieval, renaissance and baroque European craftsmen producing armour 



for the entire body from large plates were absolutely unique. In the context of this study 



“central Europe” means first of all “northern Italy” and “the German speaking lands”, while 



indeed western and southern European countries like  England, France and Spain also had 



important production sites from the second half of the 15th century on. The products of these 



countries will also be considered and compared to the German and Italian items wherever 



possible. 



The limitation of this study to the years from 1350 to 1500 is due to this period showing the 



first zenith of the art of armour making. Since the decline of the Roman Empire, of all armour 



it was only the helmets that were occasionally made of larger plates. The tendency to cover 



also the torso by larger plates can first be stated in the mid 14 th and therefore only very few 



earlier pieces could serve for the intended comparisons of technological features. 



The question on protective aspects of armour will not be discussed in this study . There are 



reams of factors and parameters that need to be considered whenever this aspect is examined. 



The field-testing of originals is out of question. Using modern reproductions would only 



make sense if the material of the tested arms and armour would  be made by the ancient 



techniques. The testing of arms -penetration would then have to be repeated with different 



arms, forces, penetration angles and beddings of the armour parts. Results would still only 



count for the tested items. Contemporarily, there was arms and armour of good and bad 







 



31 



 



quality in use. The historical accounts of many armoured men killed in battle already tell 



what would be the outcome of such “experimental archaeology”. When considering the 



number of armo ured fighters that survived battles and even blows towards their body, it 



becomes clear that the range of answers on the question of protection -effect reaches from 



“absolutely unhurt” to “immediately dead”. In between there are many different results to be 



expected, shifting to the one or the other end of the scale.  



By the beginning of the 15 th century, special armour pieces were made exclusively for 



sportive use in different types of tournaments. The study of this field of the plate armour 



production is of course a very interesting and also still neglected field. Nevertheless, 



including tournament armour into the focus of the present study would mean to compare 



additionally some thousands of extant objects  and there was simply no time for such an 



undertaking. Also horse armour could not be studied in the course of this study. The master 



armourers of the two excluded armour -categories are often the same that also made man’s 



armour for the use in the field. This leaves interesting questions open for future research , 



extending the range of this study on these two branches of the armourer’s craft.  



This research project intents to reveal details on the recurring features of field armour; wants 



to show how ideas were processed ; wants to show that norm -like features already existed 



from the earliest days of armour-making and that there has always been an immense room 



for creativity and invention. Studying and classifying the features found on extant armour 



can help to differentiate very exactly between different masters, schools, regions and times. 



This study tries to show that there is only little knowledge on this topic existing so far and 



there are many further open questions that cannot all be answered within a research project 



like the present one.  



In the course of this research, it was not possible to do any extensive archival work. The 



edited contemporary sources are very close-lipped on telling technological details. Medieval 



depictions of armourers at work are rare and they do not tell much about the technology. 



Working descriptions p articularly on armour -making were not written down; specialist’s 



knowledge was most likely exclusively handed down orally to the chosen younger 



generation of workers. This system was intended to protect the technological experience of 



the local armourer’s guild fr om competing guilds of other cities or from unauthorized 



craftsmen. Nevertheless, five relevant groups of written sources can be determined: 1. Guild-



regulations; 2. Orders; 3. Payments; 4. Legal disputes; 5. Accounts and stock -lists. A few 



hints came “coincidental” into contemporary sources of these classes. All the secrets that 



these sources do not give away, need to be revealed by considerations on the technological 



features displayed by extant armour -parts. For the understanding of the technique s that 



human beings developed – from the mining of the ores to the fighter dressed in armour – 



sources of later times, other crafts, as well as of specialist’s and own experience have to be 



consulted.  



From the early 19 th century on, in parallel to the ris ing scientific interest in the European 



Middle Ages, the collector’s demand for ancient armour was growing. As the supply of 



armour was limited, prices were rising and a flourishing modern industry, reproducing arms 



and armour, got established. Forgeries were offered on the market and some reproductions 



were sold to second or third hand as originals. Nowadays, it seems often impossible to 



distinguish between originals and reproductions in many collections all over the world. As 



this study is based on extant armour pieces, the question of authent icity is essential for any 



kind of discussion. Therefore, the concept was to purposely include identified reproductions 



and suspicious objects in this study. Comparing the details of both – reproduced and assumed 



genuine plate armour – offers a chance for finding new criteria for identifying questionable 



objects without applying expensive or even destructive natural -scientific testing methods. 







 



32 



 



The possibility for large -scale detail comparisons of objects of certain and  questionable 



provenance, on the basis of the collected data, will hopefully bring some new light into this 



dark area of the research field.  



It is still uncertain which semi-finished material the armourer used; from where he bought it 



in and which way it took from ore to sheet material. This is probably due to the necessity of 



doing such research with the help of several disciplines. To understand this field, knowledge 



of art-history, of archaeology, of history, of metalworking and of some natural sciences like 



metallurgy is necessary. Especially the ironwork in all its facets is a very wide and difficult 



field. It is also a young discipline, as iron for a long time was widely considered as a material 



irrelevant for artworks. Iron was produced in the Middle  Ages all over the world with the 



exception of Australia, New Zealand and the American continents. It could be produced in 



many different ways; the raw materials needed could be found almost everywhere. Old 



material was often recycled and the trade of iron  was widespread. All these facts make 



research on iron artifacts very complicated.  



So far, particularly the processes of making plate and its subsequent forming into a piece of 



armour were hardly the subject of studies. Many extant examples of 16 th century arsenal6 



armour are so similar to each other that they presumably were made in some kind of serial -



production processes, probably already organized in division -of-labor working processes. 



The historical development of the mass production of plate and arm our has not yet been 



examined so far. Plate armour was produced for different social classes: for the noble man, 



for the well situated citizen and for the simple foot soldier. The comparison of the dimensions 



of extant armour parts might reveal what armour was really made to measure and what was 



“one size fits all” mass-production. The research in art history was so far mostly focused on 



the expensive and richly decorated armour. The simple and undecorated items have been 



studied only rudimentary. Productio n centers for plate armour were established in several 



cities all over central, western and southern Europe. If armour pieces are not marked, the 



place of their production and the names of their makers remain unknown. It is well possible 



that a lot of the extant items were actually made at less popular sites. 



Whenever no direct written document or mark allows the tracking of the provenances, the 



scholar can try to get further by examining the technological features. Therefore, it is at first 



necessary to observe and to describe the smallest details that occur at extant armour pieces 



and to make them comparable to features at other pieces. A collection of detailed object 



images and data, organized in a database can provide the ba sis for such comparisons. To 



simplify the evaluation of the data a standardized system of nomenclature and typology of 



the contained items needs to be developed.  



Several observations on extant plate armour pieces can serve as criteria for comparisons. 



This is: the marks, materials, surface structures, decorations, edges, ridges, washers, rivets, 



applications and the different plate -joints. Also dimensions, plate -thicknesses and weights 



provide interesting data for comparisons. Such examinations might revea l unknown 



relationships between different objects and object-groups might be defined.  



The large amount of extant European plate armour pieces of the time between 1350 and 1500 



makes it difficult to examine all the technological aspects of armour making. R eams of 



contemporary artworks depict lost types and pieces of armour that could al so be organized 



and compared the sa me way like extant pieces. It was not possible to go into details on 



                                                 



6  Arsenal in the context of this study means a facility where the war-material for the equipment of huge 



numbers of soldiers was stored. The stock could quickly be handed out to personnel or citizens in case 



of danger or warfare. 







 



33 



 



depictions of armour found in art. Nevertheless, where necessary, artworks will be described 



and used as references for the understanding of extant objects. 



Preceding studies in the field usually only described one object or they compared a small 



number of objects. The common object-descriptions cannot serve as a direct basis for object-



comparisons. They were never standardized, neither in language, nor in terminology or in 



their focus. Different writers paid different attention to the observable constructional details. 



Most of the former descriptions are rather stylistic cla ssifications than descriptions of 



technological features.  



High quality object images were the most important working material for the present study. 



Despite many publications include images, details can usually not be recognized. Only few 



books contain images from different angles, but  almost never they show the interior of an 



object. The view of the latter is very important for the purpose of this study. First of all, 



because it shows constructional and technological details not visible from the main sides of 



the object. Second, t he interior surface is also the only one left in the most untouched 



condition after the armourer’s shaping-work had been finished. Hence, approximately 1300 



objects were handled and photographed by the author with specially design ed equipment. 



Each object was pictured in about 3 to 8 images, each showing the item from a different 



angle. Most of the items were measured, rubbings of marks were made and they were shortly 



surveyed. In some cases the items had to be taken off display and to be reinstalled after the 



examination. On some days, the author had worked on more than 20 items, which left not 



much time for closer examinations. The examination of details was done later at the office 



desk. Several collections could not be visited d ue to financial and time limitations. Most of 



the museums were very open for this kind of research model. Unfortunately, the curators of 



the RA, the HJRK, the RAM and the MNMB did not support the access to a larger number 



of their collectibles.  



The suggestions of this study for new scientific approaches to the topic of late medieval 



armour production are not meant to be set in stone and they are for sure not generally 



unproblematic. There is a lot of room for discussion, which hopefully will develop this topic 



further in the future. The collected data and the system in whi ch it is now organized may 



help to reveal new relationships between documents and extant item. 

2 Terminology and typology of plate armour

S. 34 · Sprachlich überarbeitet · Entwurf

2 Terminology and typology of plate armour

This study addresses the technology of armour production. It seeks to advance unresolved questions by reading surviving objects as technological documents where written evidence is lacking. Nearly 5,000 individual armour objects have been assembled in a database of images and descriptive information.7 This material becomes useful only when organised consistently, so that it can be filtered and compared from different perspectives.

The first requirement is terminology and typology that are as unambiguous as possible. As the following discussion shows, no internationally accepted, standardised system yet exists. This chapter proposes a simpler, clearer terminology to make the subject more accessible. The proposed terms are used throughout the subsequent chapters.

Originalwortlaut vergleichen
2 Terminology and typology of plate armour 



The intention of this research is, to discuss problems on the technology of armour 



manufacture. The desired results should allow bringing progress to many unsolved research-



questions in this field by replacing the lack of written sources on the technology by reading 



extant objects like technological documents. For this purpose, the author of this study has 



amassed images and object data of nearly 5000 7 single armour parts. This bulk of 



information only becomes sensible when it is organized in a uniform system t hat allows to 



filter the data with aim of comparing various aspects. The first step to such a system is a 



nomenclature and typology that is as unmistakable as possible. An internationally accepted 



and standardized nomenclature and typology of armour does not yet exist, as will be shown 



in the following. To ease the understanding of the topic, suggestions will be made on how 



the terminology of armour can be standardized in the most simple and clear way. The 



suggestions will be already applied in the subsequent chapters.
S. 34–40 · Sprachlich überarbeitet · Entwurf

2.1 Terminology and typology in current scholarship

“Poleyn, chanfron, couter, rerebrace, tasset, cuish, greave, solleret, sabaton, (Engl.); Mäusel, 



Kniekachel, Diechling, Beintasche, Spangröl, Bart, Gesässreifen, Bauchreifen, (Germ.); 



mentonniere, cubitiere, cuissard, soleret, tassiette, (Fr.); baviera, cubitiera, falda, fiancale, 



ginocchiello, (It.); bufeta, faldar, escarcela, quijotes, (Span.) etc.8”
Examples of specialist terminology; note 8. 8

To readers unfamiliar with European plate armour, such terms convey little. Every discipline needs specialist vocabulary, but a simpler international terminology could greatly improve scholarly exchange and make publications more accessible.

Several attempts have been made to establish a common terminology for arms and armour. The ambitious Glossarium armorum began publication in ten languages in 1972.9 It has nevertheless gained limited acceptance, and misunderstandings persist both between languages and within them. A concordance links the relevant terms in those volumes to the terminology proposed here [ref_tab_con] Original Excel.

In the second half of the fifteenth century, European plate armour was produced in several regions. The best-known centres were in northern Italy,10 notably Brescia11 and Milan,12 and in the German-speaking lands,13 including Innsbruck,14 Nuremberg,15 Landshut16 and Augsburg.17 Other regions also produced armour but have received less scholarly attention: western France, including Arbois;18 Flanders, including Brussels and Liège;19 Spain, including Aragon;20 and England, including London and Greenwich.21 Armourers in these regions spoke different languages and used different names for their products.

The Italian “armatura”, French “armure”, English “armour” and Spanish “armadura”, in their various spellings, derive from the Latin “arma, -orum, m”, used here for protective equipment for the body. These words occur frequently in written sources as general terms for armour, sometimes including offensive weapons. German terminology is less straightforward. The modern word “Rüstung” has no Latin root and was not used in medieval sources to mean armour.22 The usual terms were “Harnisch” and “Harnasch”, in various spellings, generally referring to plate armour. English and French sources used forms of “maille” for protection made from small interlinked rings riveted at their overlapping ends. German sources called this “Panzer”, again with varying spellings, although in modern German “Panzer” can refer to armour more generally.

The names of individual armour objects varied over time and between regions, as did the occupational title of the armourer. Pierre Terjanian states that fifteenth-century German documents generally call armourers “Harnascher”, in various spellings, and that “Plattner” became common only from the mid-sixteenth century.23 This is contradicted by German sources using “platner” for the profession before 1342.24 Fourteenth- and early fifteenth-century records in the Vienna city archive use this term exclusively. They do not use “Harnascher”, although they frequently employ “Harnasch” for body protection of different kinds:

Niclas Chöppl der Irrher schaft seinen harnasch, der zu seinem leib 



gehört hat, item ain panzir , ain Hauben, ain prustplech, ain par armgret, 



zwen hantschuch zu verkaufen.25
Vienna archival source, note 25. 25

Another potentially misleading term is “Harnaschmeister”, frequently encountered in German sources. It denotes a person professionally responsible for publicly or privately owned armour, rather than an armourer.

A few names remained familiar, but most of the vocabulary used by armourers and their customers was lost after full body armour went out of use during the seventeenth century. When interest in collecting and studying historical armour spread across Europe in the nineteenth century, scholars needed names for its different forms and components. They searched older documents, but the terms found there were not tied to illustrations. Surviving objects therefore had to be compared with contemporary depictions and matched, where possible, to the words in the records.

Some identifications were relatively clear, especially where a term was descriptive or remained familiar: “Handschuh”, “Helm”, “Beinling” and “Brust”, for example, all occur in different spellings. More abstract terms such as “Diechling” and “poleyn” were harder to connect with surviving or depicted objects.

Nineteenth-century authors often had to guess which historical term corresponded to a particular form. Where none could be found, new names were devised, including “Schwarze Schaller” and “Geschlossener Helm”. Some modern descriptions were genuinely helpful: “hour-glass”, for example, evokes the shape of a particular group of hand protection [ref_arm_1266] PDF. The result, however, was a complicated mixture of historical and modern terminology. It remains an avoidable obstacle to interdisciplinary and international research.

The inventory of movable objects at Runkelstein Castle in 1493 illustrates how difficult, and sometimes impossible, it is to connect a historical name to a specific object type.26 The English translations below retain the conventional terminology chosen for the original dissertation.27

In der 



harnaschkamer , 



genannt Neythart. 



In the armoury, called Neythart. 



Hundert und zwo 



wälsch tschaleren. 102 welsch (Italian?) sallets (helmets). 



Zwelf teutsch 



tschaleren. 12 German sallets (helmets). 



Fünff eisenhuet nach 



der alten welt. 5 kettle-hats (helmets) after the old world (?). 



Fünf schifftung und 



pärt. 



5 “Schiftungen” (reinforces?) and neck-



protections. 



Siben englisch 



stechhelm mit 



kappen. 



7 English jousting-helmets with caps 



(linings). 



Zwelf englisch 



stechhelm an kappen. 



12 English jousting-helmets without caps 



(linings). 



Zwen helm zu 



cröndlstechen. 2 helmets for the joust with Krönigen. 



Zwen waffenhelm. 2 weapon-helmets (?). 



Acht swarz wälsch 



tschalern. 8 black welsch (Italian?) sallets (helmets). 



Vier stechküris. 4 jousting-armours (breast- and maybe also 



back-plates). 



Drei krebs. 3 breastplates (maybe together with 



backplates) 



Drei prüst. 3 breastplates 



Ain halbs rüggl. Half a backplate. 



Zwai roßgstiernen. 2 shaffrons (horse head-protections). 



Newnzehen par 



armrör . 



19 pairs of vambraces (upper or lower arm-



protections). 



Aindliff achseln und 



spaneröl. 



11 spaudlers (shoulder protections) and 



Spangröls (upper arm-protections adjacent to 



the shoulders). 



Vier par clain 



achseln. 4 pairs of small spaudlers (shoulders). 



Zwen stechhelm an 



gestirn oder hauben 



zu dem tracken. 



2 jousting-helmets without the forehead or 



the caps for the “tracken” (?). 



Vier swebscheiben. 4 besagews (discs protecting the armpits).







Vierzehn par ganze 



paingewandt. 14 pairs of complete leg-dress (leg-armour). 



Drew par schinpain. 3 pairs of shin (protections for the front of the 



lower leg). 



Zwai par 



schuechgewandt. 2 pairs of shoe-dress (foot-armour). 



Sechsthalb par 



handtschuech. 6 ½ pairs of gloves (hand-protections). 



Ain drüml zu ainem 



gliger . 1 “drüml” (piece?) for a horse armour. 



Sechs stückl zu 



armrör . 



6 pieces additionally to the vambraces (elbow 



protections?). 



Ain untertail zu 



ainem kuris. 



One lower part of a Küris (breast-and 



backplate?) 



Fünff kniepückl. 5 knee-cops. 



Siben pantzer , an 



pruech. 7 ring-armour shirts without pants. 



Ain goller . 1 collar. 



Ain schurzfleck. 1 apron-piece. 



Zwo hundskappen. 2 hound-caps. 



Ain krägl. 1 collar. 



Ain kappen unter ain 



helmlin. 1 cap under a helmet. 



Ain pantzererbl. 1 ring-armour sleeve. 



Zwai par lidern 



armrör . 



2 pairs of leather-vambraces (protection for 



the upper or the lower arm). 



[…]28 […]
Runkelstein inventory and the dissertation’s accompanying English translation; note 28. Historical wording and unresolved identifications retained. 28

The translation shows that the appearance of the listed objects cannot be reconstructed from their names alone. Similar-sounding terms may also be misleading. “Hundsgugel” denotes a late fourteenth-century helmet covering the cheeks and neck and fitted with a pointed visor.29 “Hundskappe”, found in the inventory above and elsewhere,30 is frequently listed among ring-armour items and therefore cannot simply be assumed to denote plate protection.

Forms of “Schaller”, used for a helmet with an outward-flaring nape-guard, occur frequently by 1425.31 In England, “sallet” remained in use until the late sixteenth century, long after helmets comparable to the one-piece sallets of the later fifteenth century had disappeared.32 Medieval writers themselves could be uncertain about a name:

1478 Februar 11. Sigmundn Kraft bezalt ain eisenhut oder säler , …33
Payment record, note 33. 33

Two familiar examples of nineteenth-century terminology illustrate the problem further. “Black sallet”, or “Schwarze Schaller”, sometimes also called “Jagdschaller” (“hunting sallet”), takes its colour adjective from examples left unpolished and rough from the hammer. Another group consists of helmets made from a single plate covering the skull, cheeks and neck. Nineteenth-century German writers called them “Beckenhaube”, whereas French and English writers used historical forms of “bacinet”.

The difficulties are longstanding. In 1911, Charles Ffoulkes drew attention to several examples:

There are several V enetian salades in good condition, with the T-shaped 



opening for eyes and nose, a return to the form in favour in ancient 



Greece [ref_arm_2013] PDF. The term ‘barbute’ is often given to these 



helmets, or to the large bascinet with projecting cheek-plates. As a 



matter of fact, we are still uncertain as to the meaning of the word, 



except that it was a headpiece with some sort of chin protection; for 



Olivier de la Marche distinctly speaks of la bavière de sa barbute. […] 



The word barbute was also used for a man-at-arms, as we learn from Du 



Cange. With regard to the word bavière, it is interesting to note that 



Buchon has transcribed the words bachinet à bavière as bachinet à 



bannière in his edition of St. Remy’ s description of Agincourt, which 



shows how careless he was as to the description of armour .34
Ffoulkes (1911), p. 383; note 34. Quoted wording retained. 34

English-language scholarship has variously called these helmets “barbute”, “sallet in the Venetian style” and “Venetian sallet”. In 1933, Hans Müller-Hickler complained:

Die Bezeichnung „Topf-“ [ref_arm_1471] PDF oder „Kübelhelm“ 



[ref_arm_1470] PDF kennt das 14. Jahrh. nicht, sie entstand in einer Zeit 



dilettantischer Behandlung der Waffenkunde, die von Romantik geleitet, 



Namen erfand, statt die alten mit gutem Recht benutzten Bezeichnungen 



zu gebrauchen. Etwas ähnliches [sic!] erleben wir auch jetzt wieder . 



Statt der schon im 16. Jahrhundert gebrauchten so charakteristischen 



Benennung „Rüstung,“ werden gewaltsam ellenlange Namen 



ausgeheckt, die kein Mensch versteht, der Laie, der doch auch Interesse 



an der Geschichte des Vaterlandes hat, erst recht nicht. Die Franzosen 



und Engländer sind konsequenter und behalten „armure und armour“ 



bei. Die Alten nannten den Hauptschutz „Helm“ (hialm)!, Griemhelm 



(Beow. 335), Helm, Helmfahs (Bieterolf.), Helmhuot. (Nibelungenlied).35
Müller-Hickler (1932–34), p. 179; note 35. German quotation retained. 35

Müller-Hickler is probably right that historical terms were often broad, while modern names imposed artificial distinctions. He also anticipates a central aim of this study: to make the subject accessible to everyone. These examples cannot cover every terminological problem, but they show the difficulties within a single language, even before the additional obstacles to international research are considered.

Redaktionelle Hinweise · 4
  • Historische Zitate, die Inventarübersetzung und ihre Unsicherheitszeichen bleiben in der überlieferten Fassung. Die Inventartabelle wurde hier nicht neu übersetzt.
  • „with any knowledge“ im Original wurde im Kontext als „unfamiliar“ verstanden; offenbar fehlendes „without“ im ursprünglichen Satz. Bitte Autorendurchsicht.
  • Die Quelle nennt Arbois unter „Western France“. Geografische Angabe vorerst erhalten, nicht stillschweigend korrigiert.
  • Die Etymologie und grammatische Angabe „arma, -orum, m“ sind als Quellenbehauptung erhalten, aber fachlich zu prüfen.
Originalwortlaut vergleichen
2.1 Present-day’s terminology and typology  



“Poleyn, chanfron, couter, rerebrace, tasset, cuish, greave, solleret, sabaton, (Engl.); Mäusel, 



Kniekachel, Diechling, Beintasche, Spangröl, Bart, Gesässreifen, Bauchreifen, (Germ.); 



mentonniere, cubitiere, cuissard, soleret, tassiette, (Fr.); baviera, cubitiera, falda, fiancale, 



ginocchiello, (It.); bufeta, faldar, escarcela, quijotes, (Span.) etc.8” 



These terms have no meaning to a contemporary with any knowledge on European plate -



armour. While it is o f course common that each scientific discipline uses its own specific 



terminology, anyway the question might be asked if an international and simplified 



terminology would not immensely ease scientific exchange and general understanding of 



publications on the topic.  



Several attempts were made to find a uniform terminology for arms and armour. In 1972 an 



ambitious dictionary, the “Glossarium armorum”, was published in 10 languages. 9 



Nevertheless, this work has never won much recognition and until today there  is a lot of 



misunderstanding between the different languages, even within their own terminology. The 



author has made a concordance between the concerned terms in these volumes and the terms 



suggested in the present thesis [ref_tab_con]. 



European plate armour in the second half of the 15 th century was produced in different 



regions. The most famous were: Northern Italy10 (Brescia11, Milan12); The German speaking



lands13 (Innsbruck14, Nuremberg 15, Land shut16, Augsburg 17). Obviously there was also 



armour produced in many other regions, but only little research has been carried out on them 



so far: e. g. Western France (Arbois18), Flanders19 (Brussels, Liege), Spain20 (Aragonia) and 



England (London, Greenwich 21). The armourers of these different regions spoke distinct 



languages: French, English, German, Flemish, Spanish and Italian. They also used different 



terms to describe their products. 



The words “a rmatura (Italian)”, “armure (French)”, “armour (English)” an d “armadura 



(Spanish)” in different spelling clearly derive from the Latin word for a protective clothing 



of the body “arma, -orum, m”. They are frequently used in written sources of the said 



languages for describing armour in general. Sometimes this could also include the offensive 



weapons. In German it is more problematic. The modern German word “Rüstung” has no 



Latin roots and was not used in medieval sources.22 The general contemporary term used for 



armour was “Harnisch” or “Harnasch” (in different spell ings). This refers usually to plate 



armour only. While in English and French the historical term “maille” (in various spelling) 



was used for a body protection made of small interlinked rings, each riveted together at the 



overlapping ends, the German sources speak of “Panzer” (in different spelling), which is the 



modern German term for any type of armour.  



The contemporary terminology for single armour parts was very flexible and changing 



throughout the times and the different European regions. Even the term  for the job title of 



the armourer differed within time and region. Pierre Terjanian is mistaken when he says that 



the German documents of the 15th century commonly refer to the armourers as “Harnascher” 



in different spellings, and only from the mid-16th century they would frequently use the term 



“Plattner”.23 Already before 1342 the German sources use the term “platner” to define a 



certain profession. 24 The 14 th and early 15 th century sources in the archive of the city of 



Vienna exclusively use this term. Th ey never use the word “Harnascher”, despite they 



frequently use the word “Harnasch” for any kind of body protection:  



Niclas Chöppl der Irrher schaft seinen harnasch, der zu seinem leib 



gehört hat, item ain panzir , ain Hauben, ain prustplech, ain par armgret, 



zwen hantschuch zu verkaufen.25



Furthermore, the term “Harnaschmeister” often found in German sources might be 



misunderstood. It does not mean “armourer”, but it defines a person professionally 



responsible for publicly or privately owned armour.  



A few definitions might have had a familiar sound to people’s ears throughout all times, but 



most of the terms the armourers of old and their clients once used had got lost after the full 



body-armour had gone out of use in the course of the 17th century. When in the 19th century 



members of nearly all European societies became interested in the history and the collecting 



of ancient armour, it became necessary to find substitutes for the lost terms once used to 



define and describe the different armour parts and th eir segments. For this purpose those 



who occupied themselves with armour started to look for references on armour in ancient 



documents. The terms used in these sources never refer to any illustration. Therefore, it was 



necessary to compare extant armour pieces to contemporary depictions of armour and to try 



to match them to the terms found in ancient documents. 



In some cases it was of course obvious which class of armour a certain term meant, especially 



if the sources used terms that were descriptive and/or still known – for example in German: 



Handschuh, Helm, Beinling, Brust etc. (each in different spelling). For many abstract words 



found in the sources the identification with an extant or depicted armour part was more 



difficult: e. g. Diechling (Ger.), poleyn (Engl.) etc.  



In many cases authors of the 19th century just guessed what might have been the old term for 



a certain type of armour -part. Where no old definition could be found, new ones were 



created. For example for the description of different groups of helmets the terms “Schwarze 



Schaller” or “Geschlossener Helm” were created. In some cases these modern “inventions” 



were descriptive and therefore they really eased the identification to certain extend: e. g. the 



attribute “hour-glass” to describe a certain group of hand -protections [ref_arm_1266]. All 



these factors led to a complicated terminology, being a mix of ancient and modern 



definitions. This is still the situation today – a regrettable and unn ecessary obstacle for 



interdisciplinary and international research approaches. In the following some “sources of 



confusion” will be exemplified in detail. 



An inventory of all “mobile” objects present in the castle of Runkelstein in 1493 serves as 



an illustrative example on how difficult – or yet impossible – it is to connect a historical term 



to a certain type of object26:27



In der 



harnaschkamer , 



genannt Neythart. 



In the armoury, called Neythart. 



Hundert und zwo 



wälsch tschaleren. 102 welsch (Italian?) sallets (helmets). 



Zwelf teutsch 



tschaleren. 12 German sallets (helmets). 



Fünff eisenhuet nach 



der alten welt. 5 kettle-hats (helmets) after the old world (?). 



Fünf schifftung und 



pärt. 



5 “Schiftungen” (reinforces?) and neck-



protections. 



Siben englisch 



stechhelm mit 



kappen. 



7 English jousting-helmets with caps 



(linings). 



Zwelf englisch 



stechhelm an kappen. 



12 English jousting-helmets without caps 



(linings). 



Zwen helm zu 



cröndlstechen. 2 helmets for the joust with Krönigen. 



Zwen waffenhelm. 2 weapon-helmets (?). 



Acht swarz wälsch 



tschalern. 8 black welsch (Italian?) sallets (helmets). 



Vier stechküris. 4 jousting-armours (breast- and maybe also 



back-plates). 



Drei krebs. 3 breastplates (maybe together with 



backplates) 



Drei prüst. 3 breastplates 



Ain halbs rüggl. Half a backplate. 



Zwai roßgstiernen. 2 shaffrons (horse head-protections). 



Newnzehen par 



armrör . 



19 pairs of vambraces (upper or lower arm-



protections). 



Aindliff achseln und 



spaneröl. 



11 spaudlers (shoulder protections) and 



Spangröls (upper arm-protections adjacent to 



the shoulders). 



Vier par clain 



achseln. 4 pairs of small spaudlers (shoulders). 



Zwen stechhelm an 



gestirn oder hauben 



zu dem tracken. 



2 jousting-helmets without the forehead or 



the caps for the “tracken” (?). 



Vier swebscheiben. 4 besagews (discs protecting the armpits).



Vierzehn par ganze 



paingewandt. 14 pairs of complete leg-dress (leg-armour). 



Drew par schinpain. 3 pairs of shin (protections for the front of the 



lower leg). 



Zwai par 



schuechgewandt. 2 pairs of shoe-dress (foot-armour). 



Sechsthalb par 



handtschuech. 6 ½ pairs of gloves (hand-protections). 



Ain drüml zu ainem 



gliger . 1 “drüml” (piece?) for a horse armour. 



Sechs stückl zu 



armrör . 



6 pieces additionally to the vambraces (elbow 



protections?). 



Ain untertail zu 



ainem kuris. 



One lower part of a Küris (breast-and 



backplate?) 



Fünff kniepückl. 5 knee-cops. 



Siben pantzer , an 



pruech. 7 ring-armour shirts without pants. 



Ain goller . 1 collar. 



Ain schurzfleck. 1 apron-piece. 



Zwo hundskappen. 2 hound-caps. 



Ain krägl. 1 collar. 



Ain kappen unter ain 



helmlin. 1 cap under a helmet. 



Ain pantzererbl. 1 ring-armour sleeve. 



Zwai par lidern 



armrör . 



2 pairs of leather-vambraces (protection for 



the upper or the lower arm). 



[…]28 […]



This translation makes clear that the actual appearance of the mentioned item cannot be 



reconstructed. Furthermore, some historical terms might easily be confused, like the German 



term “Hundsgugel” which describes a late 14th century helmet29 enclosing cheeks and neck, 



with a pointed visor attached. Some sources (for example the inventory quoted above) use a 



similar term: “Hundskappe” 30, but in inventories this is frequently listed within the ring -



armour items and is therefore certainly not made of plate. 



The German word “Schaller” (in different spelling) used for a helmet with a flaring nape -



guard appears frequently already by 142531. In England the term “sallet” was used until the 



late 16th century – a time when no helmet comparable to the one piece “sallet” of the second 



half of the 15th century existed.32 That also the medieval writers were not so sure about how 



to name a certain helmet is evident at another document, which says:  



1478 Februar 11. Sigmundn Kraft bezalt ain eisenhut oder säler , …33  



Two popular examples of 19 th century terminology might be mentioned: The type -variant 



“black sallet” or in German the “Schwarze Schaller”, sometimes also called “Jagdschaller” 



(hunting sallet). The adjective “black” is attached as some of these helmets were left 



unpolished and rough from the hammer. Another example is a head-protection made of one 



plate which covers the skull, the cheeks and the neck. In the 19th century German literature, 



it was given the modern name “Beckenhaube”, while in French and English literat ure the 



ancient terms “bacinet” (in different spelling) was used.  



The problem of a confusing terminology in modern literature exists for long. Already by the 



year 1911 Charles Ffoulkes calls the attention to some examples:



There are several V enetian salades in good condition, with the T-shaped 



opening for eyes and nose, a return to the form in favour in ancient 



Greece [ref_arm_2013]. The term ‘barbute’ is often given to these 



helmets, or to the large bascinet with projecting cheek-plates. As a 



matter of fact, we are still uncertain as to the meaning of the word, 



except that it was a headpiece with some sort of chin protection; for 



Olivier de la Marche distinctly speaks of la bavière de sa barbute. […] 



The word barbute was also used for a man-at-arms, as we learn from Du 



Cange. With regard to the word bavière, it is interesting to note that 



Buchon has transcribed the words bachinet à bavière as bachinet à 



bannière in his edition of St. Remy’ s description of Agincourt, which 



shows how careless he was as to the description of armour .34  



Historiography in English language sometimes refers to these helmets using the term 



“barbute” and sometimes “sallet in the venetian style” or “V enetian sallet”. 



Several years after Laking Hans Müller-Hickler in 1933 complained:  



Die Bezeichnung „Topf-“ [ref_arm_1471] oder „Kübelhelm“ 



[ref_arm_1470] kennt das 14. Jahrh. nicht, sie entstand in einer Zeit 



dilettantischer Behandlung der Waffenkunde, die von Romantik geleitet, 



Namen erfand, statt die alten mit gutem Recht benutzten Bezeichnungen 



zu gebrauchen. Etwas ähnliches [sic!] erleben wir auch jetzt wieder . 



Statt der schon im 16. Jahrhundert gebrauchten so charakteristischen 



Benennung „Rüstung,“ werden gewaltsam ellenlange Namen 



ausgeheckt, die kein Mensch versteht, der Laie, der doch auch Interesse 



an der Geschichte des Vaterlandes hat, erst recht nicht. Die Franzosen 



und Engländer sind konsequenter und behalten „armure und armour“ 



bei. Die Alten nannten den Hauptschutz „Helm“ (hialm)!, Griemhelm 



(Beow. 335), Helm, Helmfahs (Bieterolf.), Helmhuot. (Nibelungenlied).35  



Müller-Hickler is presumably right when he says that the old terms were generalizing and 



that the modern ones are “violent” definition-attempts. Furthermore he antedates the primary 



concern of the present study: Making access to the topic easy for everyone. 



Not all the problems with the terminology of armour can be discus sed here, but these few 



examples might have shown how complicated research and understanding of the topic 



already in a national frame actually is – not to mention the existing obstacles for successful 



international research-cooperation.
S. 40–41 · Sprachlich überarbeitet · Entwurf

2.2 Proposals for standardised definitions

After the fall of the Iron Curtain, eastern European arms and armour collections became more accessible to international researchers. Archaeological activity also expanded over the following two decades, bringing many armour objects to light. Forms familiar from central Europe have been found, for example, in the Baltic states, in territories formerly controlled by the Teutonic Order [ref_arm_5103] PDF [ref_arm_3963] PDF [ref_arm_879] PDF [ref_arm_1733] PDF. More researchers, speaking a wider range of languages, became involved, but they still lacked an agreed international terminology.36

Agreeing on a common language would be a first step towards improving the situation. English serves as an international lingua franca across much of the educated world and has therefore been chosen for the terminology used in this study.

Standards have long been recognised as essential to international exchange in industry and commerce. In the arts, several disciplines have attempted to standardise their nomenclature, but no system has achieved general international acceptance. Research may consequently remain confined within national boundaries, obscuring historical connections across them.

The approach adopted here is to set inherited names aside initially and develop a terminology based on explicit principles. Because existing terminology offers no consistent structure, a system for classifying armour types is also required. The resulting categories nevertheless overlap with some established terms.

Human anatomy provides the first level of organisation. Six main groups are distinguished: head, neck, arms, hands, torso and legs. Protection for these regions constitutes an independent defence and can be worn separately. The more complex regions are subdivided: the torso into front, back, hip and attached thigh protection; the arm into shoulder, armpit, upper arm, elbow and forearm; and the leg into thigh, knee, lower leg and foot.

Each group contains several types. The aim is to define the common features that distinguish them. Thousands of objects were compared visually, setting aside most variations in formal design and concentrating on construction. Illustrated definitions were developed for the resulting groups. Each type is identified by its body region and a Roman numeral.

Detachable reinforcement plates for shoulders and elbows form separate subcategories. These are necessary because most armour objects surviving from before 1500 are individual pieces that cannot be assigned to an extant suit or its components. A detached reinforcement must therefore be describable in its own right. This does not imply that every individual object originally belonged to a complete suit.

A body-region type may consist of one plate or several adjoining plates. Some surviving objects lack components of their own construction, so terms for these smaller elements are also needed. Where an object is fragmentary, comparison with complete examples may establish its type. Elements are described using clear terms such as “flap”, “nape-guard” and “lame”.

Redaktionelle Hinweise · 1
  • Die ausdrückliche Abgrenzung zwischen Einzelobjekt und unvollständiger Ganzkörperrüstung folgt der verbindlichen Autorenvorgabe vom 26. September 2026. Sie ist eine klarstellende redaktionelle Ergänzung.
Originalwortlaut vergleichen
2.2 Suggestions for standardized definitions36 



With the fall of the iron curtain the eastern European collections of arms and armour got 



easier accessible for scholars from all around the world. Also archaeology throughout the 



last 2 decades got a new push and has unearthed a lo t of armour pieces. V ery often armour 



known from central Europe has been revealed, for example in the Baltic States, the former 



territories of the Teutonic knights [ ref_arm_5103] [ ref_arm_3963] [ ref_arm_879] 



[ref_arm_1733]. More and more scholars with different mother tongues got involved, still



not having a clear international terminology at hand. The first step towards an improvement 



of the situation would be an agreement on one common language. It is unquestioned that 



English is the new international “lingua franca”, at least in most of the world’s regions where 



people have access to education. Therefore, this language was chosen to determine the 



objects of interest for this study.  



In most industrial and economical branches standards have long been recognized as a 



necessary tool for a global business-exchange. In the art sector in different disciplines several 



attempts had been made to establish nomenclature standards, but none can be considered as 



internationally accepted. This leads to the result that research often ends at national borders 



and ancient cross-border connections may not be recognized.  



It therefore seemed reasonable for this study to first drop all the historically grown terms and 



then to find an entirely new logic -based terminology instead. The preceding terminology 



was not structured and therefore a classification-system of the different types of armour had 



to be developed. Nevertheless, there are intersections with the preceding terminology.  



The structuring of plate-armour by means of the human anatomy was the first organizational-



step. It was found that a first differentiation in the six main groups: head, neck, arms, hands, 



torso and leg was reasonable, as armour for each of these body-parts defines an independent 



defense that can always be worn separately. Subsequently, the more complicated body parts 



had to be divided in sub -groups: the torso in hip, the appending upper -leg and in front and 



back; the arm into shoulder, armpit, upper- and lower arm and into elbow; the leg into upper- 



and lower leg, knee and foot. Of each of these main- and sub-groups several types do exist. 



The intention was to find a definition being the lowest common denominator for describing 



each of them. The author was therefore visually comparing thousands of objects. Nearly all 



formal design-variations were purposely l eft aside and the considerations concentrated on 



the common ground from a constructional point of view. Illustrated definitions of each 



revealed group were developed. It seemed logical for their definition to keep the name of the 



type and to add roman -numbers. The shoulders and the elbows can have detachable 



reinforcement-plates that define a sub-class of these arm-protections. These sub-definitions 



were indispensable as most of the armour parts from before 1500 are single pieces, not 



attributable to an extant suit or its parts. The single extant reinforces therefore needed to be 



described by a separate type. The defined body -part types either consist of a single plate or 



they can be constructed from several adjoining plates. On many extant items some of the  



adjoining plates are missing. Therefore, but also to make closer literal description possible 



it is necessary to define also such sub-segments. Many items are only fragments and it is not 



always clear of which type they once were. In most of these cases t he identity can be 



reconstructed via comparisons to complete examples. These segments of one type will be 



defined in the text by understandable descriptive terms like “flap”, “nape-guard” or “lame”.
S. 41 · Sprachlich überarbeitet · Entwurf

2.2.1 Textile armour — outside the scope of this study

Protection made solely from padded fabric is termed “textile armour”.

Originalwortlaut vergleichen
2.2.1 Textile (not in the focus of this study) 



Armour made from padded fabric only will be described as “textile-armour”.
S. 41 · Sprachlich überarbeitet · Entwurf

2.2.2 Leather armour — outside the scope of this study

Protection made from thick, hardened leather, sometimes reinforced with metal strips or rivets, is termed “leather armour”.

Originalwortlaut vergleichen
2.2.2 Leather (not in the focus of this study) 



Armour can be made from thick and hardened leather, sometimes reinforced with metal bars 



or rivets. Such items will be described as “leather-armour”.
S. 41 · Sprachlich überarbeitet · Entwurf

2.2.3 Ring armour — outside the scope of this study

Protection made from interlinked wire rings is termed “ring armour”.

Originalwortlaut vergleichen
2.2.3 Ring-armour (not in the focus of this study) 



In the following all armour made of interlinked wire-rings is called „ring-armour“.
S. 42 · Sprachlich überarbeitet · Entwurf

2.2.4 Segmented armour — outside the scope of this study

Objects composed of separate elements held together solely by leather or fabric are not classified as plate armour in this study. They form a distinct category, termed “segmented armour”. Where they are discussed, the body region is specified: head, torso front, torso back, torso front and back, arm, hand or leg. No further subtypes are defined.

Segmented and ring armour may be assumed to have protected all body regions before 1350, throughout the period studied and after 1500, alongside plate armour.37 Ring armour is not included in the subsequent analysis.

Originalwortlaut vergleichen
2.2.4 Segmented (not in the focus of this study) 



In this study, all items made from several segments held together via leather or fabric only 



are not considered as “plate-armour”. These items belong to an own armour class described 



as “segmented-armour”. Wherever items are discussed in the following, they are described 



by the terms: head -segmented, torso -front-segmented, torso -back-segmented, torso-front-



and-back-segmented, arm-segmented, hand-segmented and leg-segmented. No further sub-



types were defined. 



It can be anticipated that segmented - and ring-armour was used for the protection of each 



part of the body before 1350, throughout the co nsidered period and after 1500 – in parallel 



to the use of plate -armour,37 but ring -armour will not be included in the following 



considerations.
S. 42 · Sprachlich überarbeitet · Entwurf

2.2.5.1.1 Armpit

Armpit protection [ref_ill_typ_arm_pit] consists of a single plate attached to a Type I [ref_arm_181] PDF or Type II shoulder defence [ref_arm_5116] PDF. Such objects appear from 1400 onwards. Round examples are known in modern literature as “Schwebscheibe” (German) and “besagew” (English).

The original position of a surviving plate disc can be difficult to determine. An early depiction shows discs laced to the shoulders and elbows of a ring-armour shirt [ref_ill_art_5167] PDF. Other contemporary images show discs on horse-head protection, pelvis protection [ref_ill_art_5191] PDF, hand protection [ref_ill_art_5252] PDF [ref_ill_art_5370] PDF [ref_ill_art_5377] PDF, elbows [ref_ill_art_5245] PDF, knees [ref_ill_art_5235] PDF, torso backs [ref_ill_art_5226] PDF [ref_ill_art_5227] PDF and head protection [ref_ill_art_5277] PDF. These uses occur across Europe throughout the fourteenth and fifteenth centuries. An isolated disc therefore cannot necessarily be assigned to a particular body region, or even to human rather than horse armour.

Originalwortlaut vergleichen
2.2.5.1.1 Armpit [ref_ill_typ_arm_pit]  



This is a single -piece defense for the armpit only that is attached to a shoulder of type -I 



[ref_arm_181] or –II [ref_arm_5116]. Such defenses appear from 1400 on. The round 



versions in modern literature were called “Schwebscheibe” (Ger.) and “besagew” (Engl.).  



It is difficult to tell where extant plate discs once had been mounted. A very early depiction 



of d iscs laced to the shoulders and at the elbows of a ring -armour shirt is found at 



[ref_ill_art_5167]. According to other contemporary depictions they appear also mounted to 



horse head -, pel vis- [ref_ill_art_5191], hand - [ref_ill_art_5252] [ ref_ill_art_5370] 



[ref_ill_art_5377], elbow - [ref_ill_art_5245], knee - [ref_ill_art_5235], torso back - 



[ref_ill_art_5226] [ref_ill_art_5227] and head- [ref_ill_art_5277] protections, all throughout 



Europe and all throughout the 14 th and 15th century. It is therefore not clear to which body 



part – or possibly horse head – a single disc once belonged.
S. 42 · Sprachlich überarbeitet · Entwurf

2.2.5.1.2.1 Type I

Type I [ref_ill_typ_arm_sho_I] is a small defence covering the shoulder joint [ref_arm_881] PDF, with articulated lames extending over part of the upper arm [ref_arm_326] PDF [ref_arm_425] PDF. It was used from around 1400 to the 1530s. Its historical German name was probably “Achsel”;38 modern terms include “Schulter” (German) and “spaudler” (English).

Originalwortlaut vergleichen
2.2.5.1.2.1 Type-I [ref_ill_typ_arm_sho_I] 



This defines a small shoulder -defense covering the shoulder joi nt [ref_arm_881] and – by 



some articulated lames – it protects parts of the upper arm [ref_arm_326] [ref_arm_425]. It 



was in use from about 1400 until the 1530ies and was historically probably called “Achsel”38 



(Ger.) and modern “Schulter” (Ger.) or “spaudler” (Engl.).
S. 42 · Sprachlich überarbeitet · Entwurf

2.2.5.1.2.2 Type II

Type II [ref_ill_typ_arm_sho_II] is a large shoulder defence with front and rear extensions, or “wings”, overlapping parts of the torso [ref_arm_611] PDF. It was used from around 1410 to 1630. It was probably also called “Achsel” in historical German sources;39 modern terms include “Schulter” (German) and “pauldron” (English).

Originalwortlaut vergleichen
2.2.5.1.2.2 Type-II [ref_ill_typ_arm_sho_II] 



This type describes a huge shoulder defense with “wings” at the front- and the backside that 



overlap parts of the torso [ref_arm_611]. It was in use from about 1410 on until 1630. 



Historically it was probably called “ Achsel”39 (Ger.) and modern “Schulter” (Ger.) or 



“pauldron” (Engl.).
S. 43 · Sprachlich überarbeitet · Entwurf

2.2.5.1.2.3 Reinforcement

This category [ref_ill_typ_arm_sho_IIr] consists of a single detachable plate reinforcing the front of a right or left Type II shoulder defence [ref_arm_742] PDF. It was used from the 1420s to the late fifteenth century.

Originalwortlaut vergleichen
2.2.5.1.2.3 Reinforce [ref_ill_typ_arm_sho_IIr] 



This is a single detachable reinforce plate for the front of a right or a left type -II shoulder 



[ref_arm_742]. It was in use from the 1420ies on until the late 15th century.
S. 43 · Sprachlich überarbeitet · Entwurf

2.2.5.1.3 Upper arm

Modern literature generally refers to upper-arm protection as “Oberarmröhre” (German) or “upper vambrace” (English).

Originalwortlaut vergleichen
2.2.5.1.3 Upper arm  



Protections for the upper arm in modern literature were usually called “Oberarmröhre” (Ger.) 



or “upper vambrace” (Engl.).
S. 43 · Sprachlich überarbeitet · Entwurf

2.2.5.1.3.1 Type I

Type I encloses half the upper arm. Italian forms cover the rear [ref_ill_typ_arm_upp_I_ita] [ref_arm_811] PDF, whereas German examples cover the outer side [ref_ill_typ_arm_upp_I_ger] [ref_arm_249] PDF. They were probably used from the late thirteenth century to the early seventeenth century.

Originalwortlaut vergleichen
2.2.5.1.3.1 Type-I [ref_ill_typ_arm_upp_I_ger] [ref_ill_typ_arm_upp_I_ita] 



This defense is enclosing the upper arm only by half. While the Italian versions cover the 



rear side [ref_arm_811], the German examples cover the outer side of the upper arm 



[ref_arm_249]. These defenses were probably in use from the late 13 th until the early 17 th 



century.
S. 43 · Sprachlich überarbeitet · Entwurf

2.2.5.1.3.2 Type II

Type II [ref_ill_typ_arm_upp_II_ita] encloses more than half the upper arm but does not surround it completely. It normally has no hinged flap [ref_arm_884] PDF. This type was used from 1420 to 1500.

Originalwortlaut vergleichen
2.2.5.1.3.2 Type-II [ref_ill_typ_arm_upp_II_ita] 



This defense is enclosing the arm more than by half, but it is not completely embracing. It 



has normally no hinged flap [ref_arm_884]. These types were in use from 1420 until 1500.
S. 43 · Sprachlich überarbeitet · Entwurf

2.2.5.1.3.3 Type III

Type III [ref_ill_typ_arm_upp_III] completely encloses the upper arm. It may form a single tube [ref_arm_511] PDF or consist of two hinged halves [ref_ill_art_5335] PDF (description 1). Such defences were used from the 1490s to the 1630s.

Originalwortlaut vergleichen
2.2.5.1.3.3 Type-III [ref_ill_typ_arm_upp_III] 



This defense is enclosing the arm completely. It might consist of a single tube [ref_arm_511] 



or it might be constructed of two halves hinged together [ ref_ill_art_5335] (descr. 1). Such 



upper arm defenses were in use from the 1490ies on until the 1630ies.
S. 43 · Sprachlich überarbeitet · Entwurf

2.2.5.1.4 Elbow

Modern literature usually calls elbow protection “Ellenbogenkachel” (German) or “elbow-cop” (English).

Originalwortlaut vergleichen
2.2.5.1.4 Elbow 



Elbow protections in modern literature are usually called “Ellenbogenkachel” (Ger.) or 



“elbow-cop” (Engl.).
S. 43 · Sprachlich überarbeitet · Entwurf

2.2.5.1.4.1 Type I

Type I [ref_ill_typ_arm_elb_I] covers only the point of the elbow [ref_arm_1021] PDF. It is uncertain whether this form existed as a distinct type: the attributed examples may be Type II defences that have lost their shell-like extensions.

Originalwortlaut vergleichen
2.2.5.1.4.1 Type-I [ref_ill_typ_arm_elb_I] 



This is a defense that encloses only the point of the elbow [ref_arm_1021]. It is not clear if 



this type of elbow defense existed as such. The examples attributed to this group might just 



have lost the shell-like extension and would therefore be rather of type-II.
S. 43 · Sprachlich überarbeitet · Entwurf

2.2.5.1.4.2 Type II

Type II [ref_ill_typ_arm_elb_II] covers the point of the elbow and extends towards the bend of the arm in a shell-like projection, without completely enclosing the joint. German [ref_arm_8] PDF [ref_arm_9] PDF and Spanish forms [ref_arm_12] PDF differ in shape from Italian examples [ref_arm_1001] PDF [ref_arm_938] PDF. The type was used in Italy from the late fourteenth century and developed in Germany and Spain during the 1450s.

Originalwortlaut vergleichen
2.2.5.1.4.2 Type-II [ref_ill_typ_arm_elb_II] 



This defense encloses the p oint of the elbow and the side where it bends by a shell -like 



extension, but it is not completely closed. The German [ref_arm_8] [ref_arm_9] and the 



Spanish versi ons [ref_arm_12] do differ in their shape from the Italian models  



[ref_arm_1001] [ref_arm_938]. In Italy such defenses were used from the late 14 th century 



on and in Germany and Spain they developed in the 1450ies.
S. 43 · Sprachlich überarbeitet · Entwurf

2.2.5.1.4.3 Reinforcement

This category [ref_ill_typ_arm_elb_IIr] consists of a single detachable plate reinforcing a left Type II elbow defence [ref_arm_888] PDF. It probably developed in the 1430s and was used only with armour of Italian style and construction, continuing until the end of the fifteenth century.

Originalwortlaut vergleichen
2.2.5.1.4.3 Reinforce [ref_ill_typ_arm_elb_IIr] 



This is a single detachable reinforce for a left elbow of type -II [ref_arm_888]. It was 



probably developed in the 1430ies and used only in combination with armour of Italian style 



and construction – until the end of the 15th century.
S. 44 · Sprachlich überarbeitet · Entwurf

2.2.5.1.4.4 Type III

Type III [ref_ill_typ_arm_elb_III] completely encloses the elbow with one plate or several articulated plates. In the fifteenth century it was used only with tournament armour. The earliest depiction occurs in René d’Anjou’s book on the Saumur Tournament [ref_ill_art_5392] PDF, dated to the 1470s.40 The type remained in use until the mid-sixteenth century.

Originalwortlaut vergleichen
2.2.5.1.4.4 Type-III [ref_ill_typ_arm_elb_III] 



This is a defense made of one or several articulated plates that enclose the elbow completely. 



In the 15th century it was only combined with tournament armour. Renè d’Anjou’s book on 



the Saumur Tournament includes the earliest depiction of such an elbow -defense 



[ref_ill_art_5392] (1470ies).40 This type was in use until the mid-16th century.
S. 44 · Sprachlich überarbeitet · Entwurf

2.2.5.1.5 Forearm

Modern literature calls forearm protection “Unterarmröhre” (German) or “lower vambrace” (English).41

Originalwortlaut vergleichen
2.2.5.1.5 Lower arm41 



Lower arm -protections in modern literature are called “Unterarmröhre” (Ger.) or “lower 



vambrace” (Engl.).
S. 44 · Sprachlich überarbeitet · Entwurf

2.2.5.1.5.1 Type I

Type I [ref_ill_typ_arm_low_I] encloses half the forearm on the side corresponding to the back of the hand [ref_arm_119] PDF. It was probably used from the late thirteenth century to the early sixteenth century.

Originalwortlaut vergleichen
2.2.5.1.5.1 Type-I [ref_ill_typ_arm_low_I] 



This defense is enclosing the lower arm at the back -of-the-hand side only by half 



[ref_arm_119]. It was in use probably from the late 13th until the early 16th century.
S. 44 · Sprachlich überarbeitet · Entwurf

2.2.5.1.5.2 Type III

Type III completely encloses the forearm with two hinged halves. Their orientation in relation to the elbow differs by approximately 90° between German [ref_ill_typ_arm_low_III_ger] [ref_arm_534] PDF and Italian forms [ref_ill_typ_arm_low_III_ita] [ref_arm_810] PDF. This type was used from the late fourteenth century to the early seventeenth century.

A comparative overview of the arm types is provided in [ref_tab_typ_arm] Original Excel.

Redaktionelle Hinweise · 1
  • Im extrahierten Text erscheint der Winkel als „900“. Als 90° gelesen; drucktypografische Verwechslung von Gradzeichen bzw. hochgestellter Null.
Originalwortlaut vergleichen
2.2.5.1.5.2 Type-III [ref_ill_typ_arm_low_III_ger] [ref_ill_typ_arm_low_III_ita] 



This defense is enclosing the lower arm completely. It is made of two hinged halves. The 



position in which th e two halves are connected to the elbow differs between the German 



[ref_arm_534] and the Italian [ref_arm_810] versions by 900 ca. This type was in use from 



the late 14th until the early 17th century. 



A comprehensive overview of the aforesaid types can be found here [ref_tab_typ_arm].
S. 44 · Sprachlich überarbeitet · Entwurf

2.2.5.2 Hand and wrist protection

Historical sources refer to hand protection as “Handschuh” in German and “gauntlet” in English, with variations in spelling. The type descriptions and illustrations below exclude finger protection. This took many forms and could be combined with different types of hand protection. Finger protection is therefore treated separately.

Redaktionelle Hinweise · 1
  • Überschrift anatomisch präzisiert: „Hand and wrist protection“. Die separate Behandlung des Fingerschutzes und die Kombinierbarkeit bleiben erhalten.
Originalwortlaut vergleichen
2.2.5.2 Hand-protection 



In historical sources all hand -protections were called “Handschuh” (Ger.; in different 



spelling) or “gauntlet” (Engl.; in different spelling). The following type -illustrations and 



descriptions do not include the finger -protections, as these varied widely just as the 



possibilities for their combination with different types of hand-protections. The fingers will 



be considered separately below.
S. 44 · Sprachlich überarbeitet · Entwurf

2.2.5.2.1 Type I — A single plate

[ref_ill_typ_han_I]

In Type I, a single plate protects the hand and encloses the wrist. Variants of this type were produced from the second half of the fourteenth century to the mid-fifteenth century [ref_arm_1252] PDF [ref_arm_1157] PDF.

In modern literature, the earlier forms are described as “Stundenglashandschuh” (German) and “hour-glass gauntlet” (English). Later forms with plates protecting the fingers together are termed “Hentzen” (German) and “Mittons” (English).

Redaktionelle Hinweise · 2
  • Die Typdefinition betrifft die Hauptplatte für Hand und Handgelenk; der Fingerschutz ist wie in der Einleitung separat zu lesen.
  • Überlieferte Fachbezeichnungen einschließlich „Mittons“ bleiben als zitierte Terminologie erhalten. Ihre Schreibweise wird nicht stillschweigend normalisiert.
Originalwortlaut vergleichen
2.2.5.2.1 Type-I [ref_ill_typ_han_I] 



This type includes all hand -protections enclosing the wrist and made of one plate only. It 



was produced in different variations from the second half of the 14 th until the mid-15th 



century [ref_arm_1252] [ ref_arm_1157]. The earlier versions in modern literature were 



called “Stundenglashandschuh” (Ger.) and “hour -glass gauntlet” (Engl.). Younger models 



with plates protecting all fingers together were called “Hentzen” (Ger.) and “Mittons” 



(Engl.).
S. 44 · Sprachlich überarbeitet · Entwurf

2.2.5.2.2 Type II — Two plates joined at the wrist

[ref_ill_typ_han_II]

Type II consists of two plates that enclose the wrist and are joined there. This type was produced from around 1440 [ref_arm_1152] PDF and remained in use into the early sixteenth century [ref_arm_1155] PDF. Modern literature refers to this type as “Hentzen” (German) and “Mittons” (English).

Redaktionelle Hinweise · 1
  • Verbindung am Handgelenk beibehalten. Keine zusätzliche Überlappungsrichtung eingeführt.
Originalwortlaut vergleichen
2.2.5.2.2 Type-II [ref_ill_typ_han_II] 



This type includes all hand -protections enclosing the wrist and being made of two plates 



joined at the wrist. This type was made from about 1440 on [ref_arm_1152] and was in use 



until the early 16 th century [ref_arm_1155]. It was called in modern literature “Hentzen” 



(Ger.) and “Mittons” (Engl.).
S. 45 · Sprachlich überarbeitet · Entwurf

2.2.5.2.3 Type III — A separate wrist plate

[ref_ill_typ_han_III]

Type III is a more complex form of hand protection consisting of several plates. Of these, only the cuff may completely enclose the forearm. A separate wrist plate lies between the cuff and the metacarpal plate—the plate covering the back of the hand—and is overlapped by both [ref_arm_1066] PDF [ref_arm_1082] PDF.

All variants allow translational movement of the hand. This type was produced from the 1460s to the end of the fifteenth century. In modern literature, it is described as “Hentze” or “Fingerhandschuh” (German), and “gauntlet” or “mitton-gauntlet” (English).

Redaktionelle Hinweise · 2
  • „Metacarpal plate“ bei der ersten Verwendung anatomisch erläutert. „Between and underneath“ als eindeutige räumliche Beziehung formuliert.
  • Fachlich noch zu präzisieren: Was genau ist mit „translational movement“ gemeint? Der Begriff und die Aussage zu allen Varianten bleiben erhalten; keine zusätzliche Aussage über eine bestimmte Bewegungsachse oder Beweglichkeit erfunden.
Originalwortlaut vergleichen
2.2.5.2.3 Type-III [ref_ill_typ_han_III] 



This type is a more complex hand -protection made of several plates. Only the cuff in some 



cases encloses the lower arm completely. Between an d underneath the cuff and the 



metacarpal plate there is a wrist plate attached [ref_arm_1066] [ref_arm_1082]. All variants 



allow the hand to be moved translational. This type was made from the 1460ies on until the 



end of the 15 th century. In modern times it was called “Hentze” (Ger.), “Fingerhandschuh” 



(Ger.), “gauntlet” (Engl.) and “mitton-gauntlet” (Engl.).
S. 45 · Sprachlich überarbeitet · Entwurf

2.2.5.2.4 Type IV — Direct attachment to the cuff

[ref_ill_typ_han_IV]

Type IV is similar to Type III but has no separate wrist plate. The metacarpal plates attach directly to the cuff [ref_arm_1190] PDF [ref_arm_1191] PDF [ref_arm_1199] PDF. This type was produced from the 1480s to the mid-seventeenth century.

A comparative overview of Types I–IV is provided in [ref_tab_typ_han] Original Excel.

Redaktionelle Hinweise · 1
  • Die Überlappung ist eine ausdrücklich ergänzte Autorenpräzisierung vom 28. September 2026. Sie ist eine inhaltliche Ergänzung, keine bloße sprachliche Glättung.
Originalwortlaut vergleichen
2.2.5.2.4 Type-IV [ref_ill_typ_han_IV] 



This type is basically similar to type-III, but it has no wrist-plate. The metacarpal plates are 



joined directly to the cuff [ref_arm_1190] [ref_arm_1191] [ref_arm_1199]. It was produced 



from the 1480ies until the mid-17th century.
S. 45 · Sprachlich überarbeitet · Entwurf

2.2.5.3 Head protection

The head types are defined by the basic protective coverage characteristic of each group.42 Chronology,43 constructional details and variations in design are not used as defining criteria.

Originalwortlaut vergleichen
2.2.5.3 Head-protection42 



The definitions of the single head -types are based on simple protective aspects that are 



characteristic for each group. Chronological43, constructional and design details were not 



attended.
S. 45 · Sprachlich überarbeitet · Entwurf

2.2.5.3.1 Type I

Type I [ref_ill_typ_hea_I] covers the upper head down to ear level without tapering inwards. The skull may consist of one plate [ref_arm_1610] PDF or several [ref_arm_1616] PDF. Its top may be rounded [ref_arm_1619] PDF, flat [ref_ill_art_5391] PDF—a form with no surviving example—or pointed [ref_arm_2093] PDF. These helmets never have an outward-flaring brim or nape-guard.

Variants existed both before and after the period studied. Modern literature uses a range of names, including “Spangenhelm”, “Bandhelm”, “Nasalhelm”, “Normannenhelm” and “Hirnhaube” in German, and “nasal-helmet”, “norman-helmet” and “skull-cap” in English.

Originalwortlaut vergleichen
2.2.5.3.1 Type-I [ref_ill_typ_hea_I] 



This group includes all helmets with an un -tapered skull that covers the upper head to the 



ear-level. The helmet can consist of one [ref_arm_1610] or more pla tes [ref_arm_1616], 



forming a rounded [ref_arm_1619], a flat-topped [ref_ill_art_5391] (no example existing) 



or a pointed skull [ref_arm_2093]. These helmets never have a flaring brim or nape -guard. 



V ariations of this helmet existed before and after the considered period. For different 



variations abstract terms were used in modern literature: e. g. “Spangenhelm”, “Bandhelm”, 



“Nasalhelm”, “Normannenhelm”, “Hirnhaube”, (all Ger.); “nasal -helmet”, “norman -



helmet”, “skull-cap” (all Engl.).
S. 45–46 · Sprachlich überarbeitet · Entwurf

2.2.5.3.2 Type II

Type II [ref_ill_typ_hea_II] completely covers the head and face, with plates extending almost to the shoulders. It does not taper inwards and has no outward-angled brim or nape-guard. All examples consist of several plates.

The earlier form appeared in the twelfth century. Modern literature calls the smaller, earlier examples “Topfhelm” (German) or “helm” (English) [ref_arm_1457] PDF, and the larger, later examples “Kübelhelm” or “great helm” [ref_arm_1461] PDF.

A second group, dating from the late fourteenth or early fifteenth century, has a pivoting face-guard and an articulated cheek-guard on the right side [ref_arm_1458] PDF. It is included in Type II because of its broad technological similarities to the helm: the face-guard invariably covers the full face, and the skull is always made from a separate plate. Ffoulkes likewise describes these as:

[…] specimens of the great bascinet with collar and visor, which is more of the helm order than helmet […]
Ffoulkes (1911), p. 383; note 44. Line breaks and spacing normalised. 44

This form has never acquired a specific modern name. Since most surviving examples were found together at Chalcis, it may be described as “Chalcis Type II”.

Originalwortlaut vergleichen
2.2.5.3.2 Type-II [ref_ill_typ_hea_II] 



This group includes helmets that cover the head and the face completely, while the plates 



nearly touch the shoulders. The shape is not tapered and no brim or nape -guard is angled 



outwards. All examples are made of several plates. The earlier variation came in fashion in 



the 12th century. The older, smaller models in modern literature are called “Topfhelm” (Ger.) 



or “helm” (Engl.) [ref_arm_1457] and the larger, younger versions were named 



“Kübelhelm” (Ger.) or “great helm” (Engl.) [ref_arm_1461]. A second, different group of 



the late 14th or early 15th century has a pivoting face-guard and at the right side an articulated 



cheek-guard attached [ref_arm_1458]. Due to its general technological similarities with the 



“helm” – the invariably full face-guard and the skull always being made of a separate pla te 



– it was put in the group of type-II helmets. Also Ffoulkes described them as:



[…] specimens of the great bascinet with collar and visor , which is more 



of the helm order than helmet […]44  



This type of helmet never got a modern, specific name. As most of the extant examples were 



found together in the city of Chalcis, they can be described as the “Chalcis type-II”
S. 46 · Sprachlich überarbeitet · Entwurf

2.2.5.3.3 Type III

Type III [ref_ill_typ_hea_III] resembles Type I but has an outward-flaring brim around its full circumference [ref_arm_1345] PDF [ref_arm_1346] PDF [ref_arm_1347] PDF [ref_arm_1348] PDF [ref_arm_1349] PDF [ref_arm_1351] PDF [ref_arm_1352] PDF [ref_arm_1353] PDF [ref_arm_1354] PDF. It existed before 1350 and continued to be made in different forms until the mid-seventeenth century.

Some mid-fifteenth-century examples can be distinguished from contemporary Type VII helmets [ref_arm_1662] PDF only in views from above, behind or inside. Such examples usually have vision slits and a rounded, rather than pointed, nape-guard [ref_arm_1419] PDF. Modern names are “Eisenhut” in German, also a historical term,45 and “kettle-hat” in English.

Originalwortlaut vergleichen
2.2.5.3.3 Type-III [ref_ill_typ_hea_III] 



This group includes al l helmets that are basically like type -I, but with a circumferential, 



flaring brim [ref_arm_1345] [ ref_arm_1346] [ ref_arm_1347] [ ref_arm_1348] 



[ref_arm_1349] [ref_arm_1351] [ref_arm_1352] [ref_arm_1353] [ref_arm_1354]. This type 



also existed before 1350 and continued to be made in different versions until the mid-17th 



century. Some extant examples of the mid-15th century can only be distinguished from some 



contemporary type-VII [ref_arm_1662] helmets when seen from top, rear or inter ior. They 



usually have vision slits and a rounded, not pointed nape -guard [ref_arm_1419]. Type-III 



helmets in modern literature is called “Eisenhut”45 (Ger.; in different spelling) or “kettle-hat” 



(Engl.).
S. 46 · Sprachlich überarbeitet · Entwurf

2.2.5.3.4 Type IV

Type IV [ref_ill_typ_hea_IV] includes open-faced helmets [ref_arm_1518] PDF and those with a face-guard pivoting either centrally at the forehead [ref_arm_1528] PDF or on both sides of the skull [ref_arm_1492] PDF. The form does not taper inwards, and the skull is usually pointed. Many examples had a ring-armour collar attached.

Modern literature calls the open-faced forms, and sometimes the visored forms, “Beckenhaube” in German and “basinet”, in varying spellings, in French and English. Historical German sources use forms of “Hundsgugel” for the visored versions.46

Originalwortlaut vergleichen
2.2.5.3.4 Type-IV [ref_ill_typ_hea_IV] 



This type describes all helmets with either an open face [ref_arm_1518] or with a face-guard 



pivoting centrally at the forehead [ref_arm_1528] or at each side of the skull 



[ref_arm_1492]. The shape is not tapered and the skull i s usually pointed. Many examples 



had a collar of ring -armour attached. The open -face models and sometimes the visored 



examples in the modern literature were called “Beckenhaube” (Ger.) or “basinet” (Fr.; Engl.; 



in different spelling). The visored versions in old sources are defined as “ Hundsgugel”46 



(Ger.; in different spelling).
S. 46 · Sprachlich überarbeitet · Entwurf

2.2.5.3.5 Type V

Type V [ref_ill_typ_hea_V] has an inward-tapering skull and a rounded, outward-flaring nape-guard. It may be open-faced [ref_arm_1982] PDF or fitted with a face-guard pivoting centrally at the forehead [ref_arm_2082] PDF or on both sides of the skull [ref_arm_2159] PDF [ref_arm_2086] PDF [ref_arm_4492] PDF.

Some examples can be distinguished from Type VII only in views from above, behind or inside. Helmets whose nape-guard is rounded rather than drawn out into an elongated point are assigned to Type V [ref_arm_2040] PDF.

Names in modern literature include “Barbuta” (German, English, French and Italian), “barbute”, “Venetian sallet” and “sallet in the Venetian style” (English). Visored forms with a ring-armour collar are called “Hundsgugel” in German or “basinet” in English and French. Around 1500, a visored form [ref_arm_1787] PDF developed into the so-called closed helmet: a separate chin plate pivoted on the same rivets as the visor [ref_arm_1936] PDF.

Originalwortlaut vergleichen
2.2.5.3.5 Type-V [ref_ill_typ_hea_V] 



This type describes all helmets with a tapered skull and a rounded  nape-guard angling 



outwards. The variations can have an open face [ref_arm_1982] or a face -guard pivoting 



centrally at the forehead [ref_arm_2082] or at ea ch side of the skull [ref_arm_2159] 



[ref_arm_2086] [ref_arm_4492]. In some cases these helmets can only be distinguished from 



type-VII helmets when a view from the top, the rear or the interior is at hand. The examples 



where the nape-guard is rounded and does not form an elongated point are attributed to group 



V [ref_arm_2040]. Helmets of this group in modern literature were called: “Barbuta” (Ger.; 



Engl.; Fr.; It.), “barbute” (Engl.), “V enetian sallet” (Engl.) or “sallet in the V enetian style” 



(Engl.). V ariations equipped with a visor and a ring -armour collar are called “Hundsgugel” 



(Ger.) or “basinet” (Engl.; Fr.). A visored variation [ref_arm_1787] around 1500 developed 



into the so called “closed helmet”, where the chin was protected by a separate plate that 



pivoted around the same rivets like the visor [ref_arm_1936].
S. 47 · Sprachlich überarbeitet · Entwurf

2.2.5.3.6 Type VI

Type VI [ref_ill_typ_hea_VI] completely encloses the head and fits so closely around the neck that the face-protecting elements must be articulated.47 All examples have a pivoting face-guard,48 although the articulation of the lower face-guards changed over time. Some fifteenth- and early sixteenth-century examples carry a small disc at the back of the neck.

The type was made from the early fifteenth century and survived in numerous forms into the first half of the seventeenth century. Modern terms include “armet” [ref_arm_1973] PDF and “bicoque” [ref_arm_1929] PDF, both French. In these forms, cheek-plates hinged to the sides of the skull meet and lock at the chin. Armets often had an attached ring-armour collar and a small disc riveted to a stem at the nape.

Forms made from the early sixteenth century were termed “geschlossener Helm” (German) or “closed-helmet” (English) by nineteenth-century writers. Their lower face-guard is not divided at the front and pivots at the sides of the skull together with the upper face-guard. A very early example is [ref_arm_1936] PDF.49

Originalwortlaut vergleichen
2.2.5.3.6 Type-VI [ref_ill_typ_hea_VI] 



This type includes all helmets that entirely enclose the head and are tapered around the neck 



so tight that the parts protecting the face need to be articulated. 47 All48 examples have a 



pivoting face-guard. The articulation system of the lower fa ce-guards varied in later times. 



At some examples of the 15 th and early 16th century a small disc was attached at the neck. 



This type of helmet was made from the early 15 th century on and continued to exist in 



numerous variations until the first half of th e 17 th century. In modern terms different 



variations were called: “armet” (Fr.) [ref_arm_1973] and “bicoque” (Fr.) [ref_arm_1929] – 



at both the cheek-plates are joined by a lock at the chin, they are articulated by hinges at the 



side of the skull. The “armets” often had a ring -armour collar attached and a small disc 



riveted onto a stick at the nape. V ariations made from the early 16 th century on in the 19 th 



century were called “geschlossener Helm” (Ger.) or “closed-helmet” (Engl.). Here the lower 



face-guards were not separated at the front and pivoted together with the upper face -guard 



at the side of the skull. A very early example is [ref_arm_1936]49.
S. 47 · Sprachlich überarbeitet · Entwurf

2.2.5.3.7 Type VII

Type VII [ref_ill_typ_hea_VII] includes open-faced helmets [ref_arm_1721] PDF and forms with a face-guard made in one piece with the skull [ref_arm_1864] PDF or pivoting at its sides [ref_arm_1727] PDF [ref_arm_1735] PDF [ref_arm_1869] PDF. The form usually tapers inwards and has an elongated, pointed, outward-flaring nape-guard.

Some examples can be distinguished from Type V only in views from above, behind or inside. An elongated point on the nape-guard determines assignment to Type VII [ref_arm_2156] PDF. The type was produced from 1440; from the early to the mid-sixteenth century it continued in use only for tournaments.

Modern names include “Schaller” and, for tournament forms, “Rennhut” (German), “celata” (Italian), “sallet” (English) and “salade” (French). Shortly before 1500, it developed into a closed helmet through the addition of neck protection pivoting together with the visor [ref_arm_1810] PDF.

Originalwortlaut vergleichen
2.2.5.3.7 Type-VII [ref_ill_typ_hea_VII]  



This group contains all helmets with an open face [ref_arm_1721], sometimes with a face-



guard either made in one piece with the skull [ref_arm_1864] or pivoting at each side of the 



skull [ref_arm_1727] [ref_arm_1735] [ref_arm_1869]. The shape is usually tapered and has 



an elongated, pointed and flaring nape -guard. In some cases th ese helmets can only be 



distinguished from type -V helmets when a view from the top, the rear or the interior is at 



hand. The examples where the nape -guard forms an elongated point are attributed to type -



VII [ref_arm_2156]. This type of helmet was produced from 1440 on and continued to be 



used for tournament only from the early to the mid-16th century. In modern literature they 



were called “Schaller” (Ger.; in different spelling), “Rennhut” (Ger.; for tournament), 



“celata” (Ital.), “sallet” (Engl.) and “salade” (Fr.). This type of helmet shortly before 1500 



developed into a “closed helmet” by t he attachment of a neck -protection that pivoted 



together with the visor [ref_arm_1810].
S. 47 · Sprachlich überarbeitet · Entwurf

2.2.5.3.8 Type VIII

Type VIII [ref_ill_typ_hea_VIII] consists of large helmets covering the entire head and part of the upper torso. Depending on their purpose, they have fixed [ref_arm_1644] PDF or screwed-on face protection [ref_arm_1646] PDF, or a visor pivoting at the sides of the skull [ref_arm_1626] PDF [ref_arm_1650] PDF. Most were intended exclusively for tournaments and had to be fastened to the torso protection.

The dissertation records the modern names “Stechhelm”, “Kolbenturnierhelm”, “Große Beckenhaube” and “Jousting-helmet” under German terminology, and “frog-mouthed jousting-helmet”, “helmet for the foot-combat” and “Great Basinet” under English terminology.

A comparative overview of the head types is provided in [ref_tab_typ_hea] Original Excel.

Redaktionelle Hinweise · 1
  • „Jousting-helmet“ ist in der Quelle der deutschen Liste zugeordnet. Diese auffällige Sprachzuordnung wurde sichtbar erhalten, nicht stillschweigend berichtigt.
Originalwortlaut vergleichen
2.2.5.3.8 Type-VIII [ref_ill_typ_hea_VIII] 



This group contains huge helmets that cover entirely the head and parts of the upper torso. 



Depending on their use they have a fixed [ref_arm_1644] or a screwed [ref_arm_1646] face-



protection or a visor pivoting at the sides of the skull [ref_arm_1626] [ref_arm_1650]. Most 



of these helmets were meant for tournament use only. They needed to be fastened to the 



torso-protection. In modern terminology the different variations were called: “Stechhelm”, 



“Kolbenturnierhelm”, “Große Beckenhaube”, “Jousting -helmet” (all Ger.); “frog -mouthed 



jousting-helmet”, “helmet for the foot-combat”, “Great Basinet” (all Engl.).  



A comprehensive overview of the aforesaid types can be found here [ref_tab_typ_hea].
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.1 Thigh

Modern literature has no specific name for thigh protection considered on its own. The combination of thigh and knee protection is usually called “Diechling” (German) or “cuisse” (English and French).

Originalwortlaut vergleichen
2.2.5.4.1 Upper Leg 



Upper leg-protections had no specific name in modern literature so far. The combination of 



an upper leg with a knee defense is usually called “Diechling” (Ger.) or “cuisse” (Engl.; Fr.).
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.1.1 Type I

Type I [ref_ill_typ_leg_upp_I] encloses half the thigh. It is the earlier form of thigh protection and was probably no longer made after 1400 [ref_arm_2910] PDF.

Originalwortlaut vergleichen
2.2.5.4.1.1 Type-I [ref_ill_typ_leg_upp_I] 



This defense is enclosing the upper leg only by half. This is the earlier type of upper leg -



protection and was probably not produced after 1400 anymore [ref_arm_2910].
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.1.2 Type II

Type II [ref_ill_typ_leg_upp_II] encloses more than half the thigh. A front plate is supplemented by a hinged flap covering the outer part of the rear, on the side corresponding to the little toe [ref_arm_2366] PDF. It was the most common form of thigh protection from 1400 to the mid-sixteenth century.

Originalwortlaut vergleichen
2.2.5.4.1.2 Type-II [ref_ill_typ_leg_upp_II] 



This defense is enclosing the upper leg more than by half. The front is covered by one plate 



and the small toe side of the rear is covered by a hinged flap [ref_arm_2366]. From 1400 on 



until the mid-16th century this was the most common upper leg defense.
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.1.3 Type III

Type III [ref_ill_typ_leg_upp_III] completely encloses the thigh, with a front plate and a hinged rear flap. This construction was probably not used for thigh protection during the fifteenth century. It is known only from a few costly suits made in the early sixteenth century.50

Originalwortlaut vergleichen
2.2.5.4.1.3 Type-III [ref_ill_typ_leg_upp_III] 



This defense is enclosing the upper leg completely. The front is covered by one plate and the 



rear is covered by a hinged flap. In the 15 th century this system was probably not used for 



the upper leg. It is known from a few costly suits of the early 16th century only50.
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.2 Knee

Modern terms for knee protection are “Kniekachel” (German) and “knee-cop” (English).

Originalwortlaut vergleichen
2.2.5.4.2 Knee 



Knee defenses in modern literature are called “Kniekachel” (Ger.) or “knee-cop” (Engl.).
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.2.1 Type I

Type I [ref_ill_typ_leg_kne_I] encloses half the knee. It is the earliest form and went out of use by the end of the fourteenth century [ref_arm_4650] PDF.

Originalwortlaut vergleichen
2.2.5.4.2.1 Type-I [ref_ill_typ_leg_kne_I] 



This defense is enclosing the knee only by half. This is the oldest knee defense, it got out of 



use by the end of the 14th century [ref_arm_4650].
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.2.2 Type II

Type II [ref_ill_typ_leg_kne_II] encloses more than half the knee through a shell-like extension on the outer side, corresponding to the little toe [ref_arm_2264] PDF. It developed in the second half of the fourteenth century and remained in use until the mid-seventeenth century.

Originalwortlaut vergleichen
2.2.5.4.2.2 Type-II [ref_ill_typ_leg_kne_II] 



This defense is enclosing the knee more than by half with a shell-like extension at the small 



toe side [ref_arm_2264]. It was developed in the second half of the 14 th century and was 



used until the mid-17th century.
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.2.3 Type III

Type III consists of several articulated lames completely enclosing the knee. It is known only from costly suits of the early sixteenth century.51

Originalwortlaut vergleichen
2.2.5.4.2.3 Type-III 



This defense consists of several articulated lames that enclose the knee completely. It is only 



known from costly suits of the early 16th century51.
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.3 Lower leg

Modern literature calls lower-leg protection “Beinröhre” (German) or “greave” (English).

Originalwortlaut vergleichen
2.2.5.4.3 Lower leg 



Lower leg defenses in modern literature are called “Beinröhre” (Ger.) or “greave” (Engl.).
S. 48 · Sprachlich überarbeitet · Entwurf

2.2.5.4.3.1 Type I

Type I [ref_ill_typ_leg_low_I] encloses half the lower leg. It is no longer found in field armour from the mid-fourteenth century onwards, and no example survives.

Originalwortlaut vergleichen
2.2.5.4.3.1 Type-I [ref_ill_typ_leg_low_I] 



This defense is enclosing the lower leg only by half. Such  a protection is not found at field 



armour from the mid-14th century on anymore and no example is extant.
S. 49 · Sprachlich überarbeitet · Entwurf

2.2.5.4.3.2 Type II

Type II [ref_ill_typ_leg_low_II] encloses more than half the lower leg. A front plate is supplemented by a hinged flap covering the outer part of the rear, on the side corresponding to the little toe. The type occurs in only a few suits from the last third of the fifteenth century [ref_arm_2828] PDF and remained in use until the mid-sixteenth century.

Originalwortlaut vergleichen
2.2.5.4.3.2 Type-II [ref_ill_typ_leg_low_II] 



This defense is enclosing the lower leg more than by half. The front is covered by one plate 



and the small toe side of the rear is covered by a hinged flap. It is found on a few armour -



suits of the last third of the 15th century [ref_arm_2828] only and continued to be used until 



the mid-16th century.
S. 49 · Sprachlich überarbeitet · Entwurf

2.2.5.4.3.3 Type III

Type III [ref_ill_typ_leg_low_III] completely encloses the lower leg with a front plate and a hinged rear flap. It is the most common form of lower-leg protection [ref_arm_2310] PDF, made from the mid-fourteenth century and used until the late sixteenth century.

Unlike other categories, these objects were frequently so neutral in form that they cannot usually be assigned to the styles or constructional traditions north or south of the Alps.

Originalwortlaut vergleichen
2.2.5.4.3.3 Type-III [ref_ill_typ_leg_low_III] 



This defense is enclosing the lower leg completely. The front is covered by one plate and the 



rear is covered by a hinged flap. This is the most common lower leg defense [ref_arm_2310]. 



It was made from the mid-14th century on and was in use until the late 16 th century. This is 



the only armour part that frequently was designed so neutral that it usually cannot be 



attributed to either the northern or the southern alpine taste or construction.
S. 49 · Sprachlich überarbeitet · Entwurf

2.2.5.4.4 Foot

Modern literature uses “Schuh” (German) and “solleret” or “sabaton” (English and French) for foot protection.

Originalwortlaut vergleichen
2.2.5.4.4 Foot 



Foot protec tions in modern literature are called “Schuh” (Ger.) or “solleret”/”sabaton” 



(Engl.; Fr.).
S. 49 · Sprachlich überarbeitet · Entwurf

2.2.5.4.4.1 Type I

Type I [ref_ill_typ_leg_foot_I] has a single plate covering the toes, usually connected to the lower-leg protection by ring armour [ref_arm_2781] PDF. It was probably used from the 1440s to the 1520s.

Originalwortlaut vergleichen
2.2.5.4.4.1 Type-I [ref_ill_typ_leg_foot_I] 



At this type only one single plate covers the toes. It is usually connected to the lower leg via 



ring-armour [ref_arm_2781]. This type was probably in use from the 1440ies until the 



1520ies.
S. 49 · Sprachlich überarbeitet · Entwurf

2.2.5.4.4.2 Type II

Type II [ref_ill_typ_leg_foot_II] consists of several articulated plates covering the foot up to the ankle region [ref_arm_2255] PDF. It was probably the most common form of foot protection from the late fourteenth century to the mid-sixteenth century.

Redaktionelle Hinweise · 1
  • „Knuckles“ wurde nach der bisherigen zeichnungsbasierten Interpretation als „ankle region“ gefasst. Diese fachliche Präzisierung ist noch vom Autor zu bestätigen.
Originalwortlaut vergleichen
2.2.5.4.4.2 Type-II [ref_ill_typ_leg_foot_II] 



At this type several articulated plates cover the foot till the knuckles [ref_arm_2255]. This 



was probably the most common foot protection from the late 14 th century on until the mid-



16th century.
S. 49 · Sprachlich überarbeitet · Entwurf

2.2.5.4.4.3 Type III

Type III [ref_ill_typ_leg_foot_III] consists of several articulated plates covering the foot and heel [ref_arm_2257] PDF.

A comparative overview of the leg types is provided in [ref_tab_typ_leg] Original Excel.

Originalwortlaut vergleichen
2.2.5.4.4.3 Type-III [ref_ill_typ_leg_foot_III] 



Several articulated plates cover all the foot and the heel [ref_arm_2257]. 



A comprehensive overview of the aforesaid types can be found here [ref_tab_typ_leg].
S. 49 · Sprachlich überarbeitet · Entwurf

2.2.5.5.1 Type I

Type I [ref_ill_typ_nec_I] protects the front of the neck and is used with helmets that leave the chin and throat uncovered, notably Type VII. It covers the chin, throat and upper front of the torso where the torso defence leaves a gap.

Its main structure is a single plate closely fitted to the chin and upper chest. One or more articulated lames may be added at its upper edge [ref_arm_3173] PDF. The type developed in the second half of the fifteenth century and was no longer used after 1500. Historical and modern German terminology uses forms of “Bart”;52 the modern English term is “bevor”.

Originalwortlaut vergleichen
2.2.5.5.1 Type-I [ref_ill_typ_nec_I] 



This type describes a protection for the frontal parts of the neck, used together with helmets 



that do not cover the chin and the throat (type -VII). It protects the chin, the throat and the 



frontal upper parts of the torso, where the torso-defense leaves the wearer unprotected. This 



type consists of one plate only, closely fitted to the chin and the upper chest. Only at the 



upper end one or more articulated lames might be attached [ref_arm_3173]. Such protections 



developed in the second half of the 15th century and were not used after 1500 anymore. This 



was historically and in modern literature called a “Ba rt”52 (Ger.; in different spelling) or 



modern “bevor” (Engl.).
S. 50 · Sprachlich überarbeitet · Entwurf

2.2.5.5.2 Type II

Type II [ref_ill_typ_nec_II] provides essentially the same coverage as Type I but consists of at least two plates: one for the chin and another for the upper chest, joined at throat level. One or more articulated lames may be attached at the upper edge [ref_arm_3034] PDF. It was worn with Type III, VI [ref_arm_3044] PDF and VII helmets.

Originalwortlaut vergleichen
2.2.5.5.2 Type-II [ref_ill_typ_nec_II] 



This type is basically the same as type -I, but it consists of at least two p lates. One is 



protecting the chin and the second one the upper chest. They are fixed together at the throat-



level. At the upper end one or more articulated lames might be attached [ref_arm_3034]. It 



was worn in combination with helmets of type-III, -VI [ref_arm_3044] or -VII.
S. 50 · Sprachlich überarbeitet · Entwurf

2.2.5.5.3 Type III

Type III [ref_ill_typ_nec_III] forms a complete collar, protecting the front and back of the upper torso, the shoulders and the throat, but not the chin. Both front and back consist of at least two plates [ref_arm_3152] PDF. It was used from the 1430s to the end of the sixteenth century. Historical and modern terms include “Kragen” and “Harnischkragen” (German) and “collar” (English).

A comparative overview of the neck types is provided in [ref_tab_typ_nec] Original Excel.

Originalwortlaut vergleichen
2.2.5.5.3 Type-III [ref_ill_typ_nec_III] 



This type describes a full collar -plate, protecting the front and the back of the upper torso, 



the shoulders and the throat but not the chin. Each, the front and the back-side, consists of at 



least two plates [ref_arm_3152]. This type was in use since the 1430ies and remained in use 



until the end of the 16th century. In old and modern literature this was called “Kragen” (Ger.), 



“Harnischkragen” (Ger.) and “collar” (Engl.).  



A comprehensive overview of the aforesaid types can be found here [ref_tab_typ_nec].
S. 50 · Sprachlich überarbeitet · Entwurf

2.2.5.6.1 Type I

In Type I [ref_ill_typ_tfr_I] [ref_ill_typ_tba_I], the chest and abdomen are covered by a single plate [ref_arm_3734] PDF or by several vertical plates [ref_arm_3811] PDF. These do not flare outwards at the waist. Some examples may have carried pelvis lames, as seen in [ref_arm_3698] PDF.

Type I breastplates were used from the mid-fourteenth century to around 1410. Backplates did not develop alongside them: surviving Type I backplates date from the end of the fifteenth century and never have attached pelvis lames [ref_arm_3417] PDF. The type previously had no specific name; the original dissertation proposes “einteilige/r Brust/Rücken” (German) or “single-piece back-/breastplate” (English).

Redaktionelle Hinweise · 1
  • Die vorgeschlagene historische Redaktionsbezeichnung „single-piece“ steht neben einer Definition, die auch mehrere vertikale Platten umfasst. Widerspruch sichtbar erhalten; hier nicht als neue neutrale Typbezeichnung übernommen.
Originalwortlaut vergleichen
2.2.5.6.1 Type-I [ref_ill_typ_tfr_I] [ref_ill_typ_tba_I] 



At this type the thorax and the abdomen are covered by one plate [ref_arm_3734] or by 



several vertical plates [ref_arm_3811] which are not angling outwards at the waistline. Some 



examples might have had pelvis -lames attached, similar to [ref_arm_3698]. Type -I 



breastplates were only used from the mid-14th century until 1410 ca. Type-I backplates did 



not develop in parallel to the breastplates. There are type-I backplates existing, but they date 



from the end of the 15 th century and never a ny pelvis-lames are attached [ref_arm_3417]. 



This type had no specific name before. It might be described as “einteilige/r Brust/Rücken” 



(Ger.) or “single-piece back-/breastplate” (Engl.).
S. 50 · Sprachlich überarbeitet · Entwurf

2.2.5.6.2 Type II

In Type II [ref_ill_typ_tfr_II] [ref_ill_typ_tba_II], a single plate covers the chest and abdomen and flares outwards at the waist to connect with the pelvis lames. This type was used from the 1480s [ref_arm_3522] PDF [ref_arm_3371] PDF to the mid-seventeenth century.

It previously had no specific name. The original dissertation proposes “einteilige/r Brust/Rücken mit Gesäßreifen” (German) or “single-piece back-/breastplate with fold” (English).

Originalwortlaut vergleichen
2.2.5.6.2 Type-II [ref_ill_typ_tfr_II] [ref_ill_typ_tba_II] 



At this type the thorax and the abdomen are co vered by one plate angling outwards at the 



waistline to join the pelvis -lames. Plates of this type were in use from the 1480ies 



[ref_arm_3522] [ref_arm_3371] until the mid-17th century. This type had no specific name 



before. It would have been described as “einteilige/r Brust/Rücken mit Gesäßreifen” (Ger.) 



or “single-piece back-/breastplate with fold”.
S. 50 · Sprachlich überarbeitet · Entwurf

2.2.5.6.3 Type III

In Type III [ref_ill_typ_tfr_III] [ref_ill_typ_tba_III], separate plates protect the chest and abdomen. The abdominal element may consist of several plates [ref_arm_3334] PDF and lies beneath the chest plate. It flares outwards at the waist to connect with the pelvis lames [ref_arm_3429] PDF [ref_arm_3264] PDF. This type was used from the 1450s to the mid-sixteenth century and previously had no specific name.

Originalwortlaut vergleichen
2.2.5.6.3 Type-III [ref_ill_typ_tfr_III] [ref_ill_typ_tba_III] 



The thorax and the abdomen are covered by separate plates. The abdomen-plate can consist 



of several plates [ref_arm_3334] and lies underneath the thorax-plate. It is angling outwards 



at waistline to join the pelvis -lames [ref_arm_3429] [ref_arm_3264]. This type was in use 



from the 1450ies on until the mid-16th century. It had no specific name so far.
S. 50 · Sprachlich überarbeitet · Entwurf

2.2.5.6.4 Type IV

In Type IV [ref_ill_typ_tfr_IV] [ref_ill_typ_tba_IV], separate elements protect the chest and abdomen. The abdominal plate lies outside the chest element, which may consist of one plate or several lames. It flares outwards at the waist to connect with the pelvis lames [ref_arm_3627] PDF [ref_arm_3412] PDF [ref_arm_3374] PDF.

Breastplates of this type were made from around 1400 to the mid-sixteenth century. Backplates were no longer produced after 1500. The German term was “geschiftete/r Brust/Rücken”.

Redaktionelle Hinweise · 1
  • Die grammatisch mehrdeutige Einschaltung „made of a single plate or several lames“ ist hier auf das Thoraxelement bezogen. Bitte anhand der Originaldefinition bestätigen.
Originalwortlaut vergleichen
2.2.5.6.4 Type-IV [ref_ill_typ_tfr_IV] [ref_ill_typ_tba_IV] 



The thorax and the abdomen are covered by separate plates. The abdomen -plate lies upon 



thorax-plate – made of a single plate or several lames – and is angling outwards at the 



waistline to join the pelvis -lames [ref_arm_3627] [ ref_arm_3412] [ ref_arm_3374]. 



Breastplates of this type were made from about 1400 until the mid-16th century. Backplates 



were not produced after 1500 anymore. This type was called “geschiftete/r Brust/Rücken”.
S. 51 · Sprachlich überarbeitet · Entwurf

2.2.5.6.5 Thigh protection attached to the torso

This category [ref_ill_typ_tfr_leg] protects the right or left thigh and attaches to the pelvis lames of Type II, III or IV front torso protection. From around 1440 to the early sixteenth century, it was made from a single plate [ref_arm_3796] PDF. From the late 1480s, articulated lames were also used [ref_arm_3574] PDF.

From the mid-sixteenth century, this construction developed into long thigh defences with attached knee protection. By the end of that century, it had entirely replaced separate leg protection. Modern terms are “Beintaschen” (German) and “tassets” (English).

Originalwortlaut vergleichen
2.2.5.6.5 Torso upper leg-protection [ref_ill_typ_tfr_leg]  



This is a protection for the left or the right upper leg, attached to the pelvis-lames of a torso-



front-protection of type-II, -III or -IV . From about 1440 on until the early 16th century they 



were made of a single plate [ref_arm_3796]. From the late 1480ies on they could be made 



of several articulated lames [ref_arm_3574]. This system from the mid-16th century on 



developed into long upper leg-protections with knee defenses attached – until the end of the 



century it had completely replaced the separate leg -protection. In modern literature these 



protections are called “Beintaschen” (Ger.) or “tassets” (Engl.).
S. 51 · Sprachlich überarbeitet · Entwurf

2.2.5.6.6 Hip protection

Hip protection [ref_ill_typ_tor_hip] consists of a small plate buckled to the pelvis lames at the front and back of the torso. It occurs on armour made between 1440 and 1500 [ref_arm_3926] PDF.

A comparative overview of the torso types is provided in [ref_tab_typ_tor] Original Excel.

This classification makes it possible to keep track of surviving objects while keeping descriptions concise and unambiguous. Its structure allowed the photographs and data for thousands of objects to be organised in a digital database. The system can be extended beyond this study’s scope, for example to later periods or tournament armour. A diagram illustrates the proposed definitions and the scope of the study [ref_ill_dia_typ]; a concordance links object numbers to armour types [ref_tab_ID-type] Original Excel.53 Chapter 3 discusses their periods of use in greater detail.

The number of surviving objects in each category is also of interest. A short statistical summary is provided in [ref_tab_numb] Original Excel. Pairs of limb and hand protection are counted as two objects, which increases their apparent numbers. Even so, Type V and VII helmets and Type II and IV breastplates are the most numerous. Almost all the individual components of the cited suits are included in the relevant type counts. Many of these suits are composite, incomplete or reproduced.

The terminology is based solely on surviving objects. Visual sources suggest that further types once existed but have not survived. This is a proposed system, intended for further practical testing and discussion.

Originalwortlaut vergleichen
2.2.5.6.6 Hip protection [ref_ill_typ_tor_hip] 



This is a small plate, buckled to the  pelvis-lames of the front - and the backplate to protect 



the hip. This is found at armour made between 1440 and 1500 [ref_arm_3926].  



A comprehensive overview of the aforesaid types can be found here [ref_tab_typ_tor]. 



The structuring of all types proved to be the right way to keep an overview on all extant 



items and to keep descriptions in the text unmistakably and short. Only with the help of this 



clear structure all the collected pictures and data of thousands of objects could be organized 



in a digital database. The system is designed to allow range -extensions to armour pieces 



outside the focus of this study, e.g. of later periods or also to tournament armour. The author 



has tried to visualize the suggested definitions and the focus of this study in a clear structured 



diagram [ ref_ill_dia_typ]. To provide a better overview , a concordance of number and 



belonging armour-type is found here [ref_tab_ID-type]53. In chapter [A brief history of plate 



armour from a technological point of view ] closer descriptions are given on the periods in 



which the certain types were used. 



It is of course an interesting question, how many objects of each type are extant. The author 



extracted a small statistic from his database [ref_tab_numb]. As the extant pairs of limb and 



hand protections count twice, they seem to be extant in large numbers. Considering this, it 



is interesting to note that it is the helmets of type -V and -VII and the breastplates of type-II 



and -IV which are extant in the largest numbers. Nearly all single parts of the quoted suits 



are included in the counts on the single armour -types. Many of the suits are composite, 



incomplete or reproduced. 



The terminology used here was developed by the observation of extant examples only. 



According to many pictorial sources, several more types of each category might have existed 



but have not survived. This terminology is just a suggestion and should undergo further 



practical testing and discussion in the future.

3 A brief technological history of plate armour

S. 52 · Sprachlich überarbeitet · Entwurf

3 A brief technological history of plate armour

The stylistic development of European plate armour has been described extensively in works such as Wendelin Boeheim’s Handbuch der Waffenkunde,54 Ortwin Gamber’s Harnischstudien55 and Claude Blair’s European Armour.56 This chapter complements those studies by considering what may have prompted armourers to alter established forms of construction. It concentrates on the principal constructional changes during the period examined, beginning with the transition from segmented protection to larger plates and ending with mass production and decoration in the so-called Maximilian style. Where relevant, it also notes constructions that continued unchanged in later periods.

Contemporary images often show armour that does not fit the typology developed here. Establishing whether such forms existed, and how they might have been constructed, remains a substantial task for future research. The following discussion is organised by body region.

Established textile, leather, segmented and ring armour offered less protection in some respects than plate armour, but could be lighter and more flexible, with fewer vulnerable gaps. Its manufacture also required less specialised equipment and skill. Grinding and polishing, for example, were necessary only for segmented plates exposed on the outside of a textile, leather or underlying garment.

Reproducing these advantages with large, rigid plates of iron or steel was difficult.57 Armour-making therefore involved continuing experimentation with fashion, protection and comfort. Changes in form did not necessarily improve protection, and apparently older types continued to be made and worn alongside newer inventions. The combinations used for complete arm, leg58 and torso protection59 must consequently be considered as systems that varied by period and region.

Originalwortlaut vergleichen
3 A brief history of plate armour from a technological point of view 



The stylistic genesis of European plate armour is described sufficiently in publications like 



Wendelin Boeheim’s “Handbuch der Waffenkunde” 54, Ortwin Gamber’s 



“Harnischstudien”55 or Claude Blair’s “European Armour” 56 – to name the most 



recommendable works only. The following comments try to extend these works by attempts 



of recreating what might have been the armourer’s considerations when he changed the 



construction of a certain established armour part. The regard is limited to the major 



constructional changes that emerged throughout the considered period. The discussion 



begins with types made in the times when segmented armour changed over to larger plates. 



It will end with the introduction of the mass production and the decoration of armour in the 



so called “Maximilian” style. Occasionally it will be noted wherever a certain construction 



was still produced unaltered in later times. Contemporary artworks often sho w armour that 



does not fit into the type-scheme developed for this study. The discussion of the probability 



that certain items really existed and how they might have been constructed is a wide field 



for future studies. The remarks will be split into sub -chapters, named after the concerned 



body part.  



The long established textile -, leather - segmented- and ring -armour had protective 



disadvantages in comparison to plate armour, but such armour could be lighter and more 



flexible while it left less “dangerous” c hinks. Furthermore, the craftsmen making such 



armour needed less specialized skills, less tools etc. For example grinding and polishing was 



only necessary for segmented -armour plates placed exteriorly to a fabric, leather or 



undergarment. It was not easy f or the armourers to meet the positive properties of the 



established armour types with the inflexible, large iron or steel57 plates. Due to these natural 



limitations, armour making throughout the considered decades was rather a permanent 



experimenting and ch anging of aspects of fashion, protection and wearing -comfort. As a 



result, the developments of the single plate -armour types do not necessarily come together 



with protective improvements. Many presumably “older” types of plate armour have always 



been made and used in parallel to “new” inventions. This makes it necessary to describe the 



different combination-systems of complete limb 58 and torso59 protections, as they can vary 



in different times and regions.
S. 53 · Sprachlich überarbeitet · Entwurf

3.1 Arm protection

Making plate protection for the limbs was probably among the armourer’s most demanding tasks. It is therefore striking that contemporary images suggest that, apart from helmets, the earliest medieval armour made from larger plates protected the arms and legs [ref_ill_art_5343] PDF (description 1). Comfortable, fully enclosing leg protection is difficult enough to make; arm protection presents still greater challenges.

Unlike the lower leg at the knee, the forearm can rotate through the combined action of its two bones and the elbow region. The original dissertation describes a range approaching 360° at the wrist and about 160° of elbow flexion. The shoulder permits the entire arm to move in a circle. Covering these movements with adjoining plates while allowing the wearer to wield a weapon required careful arrangement, particularly around the elbow and forearm.

Ring- and textile-armour sleeves preserved mobility, but by the High Middle Ages were considered insufficient against penetration and blows from various weapons. In the late thirteenth century, armourers began adding plate or leather elements to, or between, ring, textile and segmented protection; the knee defence [ref_arm_4650] PDF is one example. The early forms are outlined below, followed by the development of the systems in which the plates were combined.

Redaktionelle Hinweise · 1
  • Die im Original genannten Bewegungswinkel und die Aussage zur fehlenden axialen Rotation am Knie wurden als Quellenbeschreibung sichtbar gemacht, nicht als neu überprüfte anatomische Messwerte. Vor einer fachlichen Neufassung präzisieren.
Originalwortlaut vergleichen
3.1 Arm-protection  



The making of plate -protections for t he limbs was probably the most challenging task for 



the armourer. It is therefore very surprising to see that – according to contemporary artworks 



and with the exception of the helmet – the first medieval armour to consist of larger plates 



was made for the arms and the legs [ref_ill_art_5343] (descr. 1). While it is already difficult 



enough to entirely protect the leg in a comfortable way by plates, this is even more 



complicated with the ar ms. While the knee allows no axial turning for the lower leg, the 



elbow and the two-boned lower arm can twist, to allow a turning of the wrist to nearly 360 



degrees. The elbow can be bent to about 160 degrees. The shoulder allows a circular motion 



of the whole arm. Due to these facts, it is a difficult task to cover the arms with adjoining 



protections and to still allow an armoured man to fight with a weapon. These demands make 



clear that solutions had to be found for arranging protecting plates in a way so the movement 



of the elbow and the lower arm would not be limited. 



The long-used ring- or textile-armour sleeve did not restrain the arm’s mobility, but already 



in the high middle -ages this protection type was considered to be insufficient against 



penetrations and blows from different kinds of weapons. When in the late 13 th century the 



armourers tried to improve the protection -systems, they started to fasten segments of plate 



or leather onto or in between the ring - (e. g. the knee [ ref_arm_4650]), the textile - or the 



segmented-armour.  



In the following, early arm -defenses will be shortly described. Subsequently, the 



development of the different plate-types will be discussed at examples of the different arm-



protection systems.
S. 53–54 · Sprachlich überarbeitet · Entwurf

3.1.1 Shoulder

Until the second half of the fourteenth century, shoulders were protected only by ring armour [ref_ill_art_5189] PDF or segmented armour.60 The varied, unstandardised arm defences of that period allowed movement but left gaps between the plates, covered only by ring armour.

The earliest surviving medieval shoulder elements are small plates attached to segmented front-and-back torso protection [ref_arm_3904] PDF [ref_arm_3906] PDF [ref_arm_3912] PDF. In [ref_arm_3910] PDF, a small articulated plate is attached at each shoulder. These are not fully developed shoulder defences: they cover the collarbones but offer little coverage of the shoulder joints.

Type I shoulder protection developed during the second half of the fourteenth century. One of its earliest independent depictions is [ref_ill_art_5289] PDF (description 2). The small form frequently shown in German-speaking regions between 1420 and 1450 [ref_ill_art_5176] PDF [ref_ill_art_5198] PDF may be represented by the early surviving example [ref_arm_326] PDF, still assembled from very small plates. Larger Type I examples, probably also from the first half of the fifteenth century, include [ref_arm_204] PDF [ref_arm_220] PDF [ref_arm_330] PDF [ref_arm_427] PDF [ref_arm_881] PDF [ref_arm_5017] PDF [ref_arm_5090] PDF.

To improve coverage of the shoulder joint, Italian armourers developed large, multi-lame Type II defences in the early fifteenth century [ref_arm_565] PDF. A disc could be fitted to the left shoulder, as in the later depiction [ref_ill_art_5270] PDF, or a closely fitting reinforcement could be attached to the front of either shoulder [ref_arm_742] PDF [ref_arm_744] PDF. The latter arrangement continued to the end of the century.

Type II shoulders remained asymmetrical until the late sixteenth century. On the right, a cut-out in the front extension at the armpit accommodated the lance beneath the arm [ref_arm_5058] PDF. Once the lance ceased to be used in battle towards the end of that century, symmetrical shoulders became common.

Originalwortlaut vergleichen
3.1.1 Shoulder 



Until the second half of the 14 th century the shoulder was only 60 covered by ring - 



[ref_ill_art_5189] or segmented -armour. Such different, not standardized arm-defense 



variations of the 14 th century did not restrain the arm’s flexibility, but chinks – again only 



protected by ring -armour – were left between the plates. The oldest medieval shoulder 



defenses to survive are small plate -segments attached to segmen ted torso-front-and-back-



protections [ref_arm_3904] [ref_arm_3906] [ref_arm_3912]. At [ref_arm_3910] one small 



articulated plate is attached at each side of the shoulders. They cannot be considered as real 



shoulder defenses, as they only cover the collarbone and only very insufficiently the shoulder 



joint.  



In the second half of the 14 th century the armourers developed shoulders of type -I. One of 



the oldest depictions  of independent shoulder protections of type -I is found at 



[ref_ill_art_5289] (descr. 2). The oldest surviving example of a small type -I shoulder often 



found at contemporary artworks of the German speaking lands between 1420 and 1450 



[ref_ill_art_5176] [ref_ill_art_5198] is probably [ ref_arm_326] – still made of very small 



plates. Larger examples of type -I, probably also of the first half of the 15 th century are 



[ref_arm_204] [ref_arm_220] [ref_arm_330] [ref_arm_427] [ref_arm_881] [ref_arm_5017] 



[ref_arm_5090].  



To temper with the insufficient protection of the sh oulder-joints, in the early 15 th century 



[ref_arm_565] the Italian armourers developed large shoulder defenses consisting of several 



lames (type-II). To the left shoulder a disc [ref_ill_art_5270] (a late example) or at the front



of each shoulder until the end of the century a close fitting reinforcement could be attached 



[ref_arm_742] [ref_arm_744]. Until the late 16 th century the shoulder defenses of type -II 



were unsymmetrical. At the right side it was necessary to leave a cutout in the armpit-region 



of the frontal wing to allow the lance to be pinched under the arm [ref_arm_5058]. When by 



the end of the 16 th century the lance was not used in battle anymore the shoulders were 



frequently made symmetrical.
S. 54 · Sprachlich überarbeitet · Entwurf

3.1.2 Armpit

A single pair of shoulder defences could carry differently shaped armpit plates [ref_ill_art_5253] PDF. Images also indicate protection at the rear of the armpit [ref_ill_art_5188] PDF [ref_ill_art_5203] PDF. The forms and ridge decoration shown on the effigy of Konrad of Weinsberg, around 1430 [ref_ill_art_5223] PDF (description 1), and the cenotaph of Johann of Freiburg [ref_ill_art_5238] PDF (description 1), closely resemble the sole surviving example of this particular form [ref_arm_880] PDF. During the second half of the fifteenth century, armpit plates were used chiefly in German-speaking regions and were often round [ref_ill_art_5366] PDF (description 2).

Originalwortlaut vergleichen
3.1.2 Armpit 



Different shapes of armpit protections can appear at one particular pair of shoulders 



[ref_ill_art_5253]. According to illustrations also protections for the rear side of the armpits 



existed [ref_ill_art_5188] [ref_ill_art_5203]. At the effigy of Konrad of Weinsberg 1430 ca. 



[ref_ill_art_5223] (descr. 1) and at the cenotaph of Johann of Freiburg [ ref_ill_art_5238] 



(descr. 1) the armpits are strikingly similar in shape and ridge decoration to the only extant 



example [ref_arm_880]. In the second half of the 15 th century they are merely used in the 



German speaking countries and they are frequently round [ref_ill_art_5366] (descr. 2).
S. 54 · Sprachlich überarbeitet · Entwurf

3.1.3 Upper arm

Possibly from the twelfth century, thick, hardened leather61 was used for nearly enclosing protection tied around the upper arm—the only surviving example is [ref_arm_954] PDF, comparable to [ref_ill_art_5167] PDF—and the forearm [ref_ill_art_5249] PDF (description 1). Fourteenth-century examples could be reinforced with applied metal strips [ref_ill_art_5157] PDF; a later example appears in [ref_ill_art_5244] PDF.

Type III upper-arm protection was already used in Germany by 1365.62 Probably from the 1430s, the Italian system enclosed almost the whole upper arm with a single metal plate, Type II. Its lower edge was cut away on the side towards the torso, allowing the arm to lie close to the breastplate’s arm opening [ref_arm_3933] PDF.

Redaktionelle Hinweise · 1
  • Die Datierung vollständig geschlossener Oberarmplatten schon 1365 steht neben der späteren Chronologie in §2.2.5.1.3.3. Beide Quellenangaben erhalten; nicht harmonisiert.
Originalwortlaut vergleichen
3.1.3 Upper arm 



Possibly from the 12th century on, nearly enclosing plates of thick, hardened61 leather were 



tied to the upper (the only existing example is [ ref_arm_954], compare [ref_ill_art_5167]) 



and the lower arm [ref_ill_art_5249] (descr. 1). In the 14th century, sometimes they could be 



reinforced by applied metal bars [ref_ill_art_5157]. A rather late example is found depicted 



on [ ref_ill_art_5244]. Already by 1365 in Germany type -III upper arm defenses were in 



use62. Probably from the 1430ies on the upper arms of the Italian system were nearly 



completely enclosed by one metal-plate (type-II). Towards the torso the plate was cut out at 



the lower edge to allow the arms to be put closely to the arm -cutouts of the breastplate 



[ref_arm_3933].
S. 54 · Sprachlich überarbeitet · Entwurf

3.1.4 Elbow

Disc-shaped elbow protection appears in English artworks from 1260 onwards.63 Leather may also have been moulded into a shell-like form and fastened over the elbow point. A plate enclosing the joint too closely would prevent it from bending. Armourers addressed this by extending the elbow plate into a leaf-like projection, Type II [ref_arm_362] PDF. These shell-like extensions subsequently grew much larger to increase protection [ref_arm_52] PDF.

The left elbow, particularly exposed when fighting on horseback with a lance, could carry an additional, larger and thicker detachable reinforcement [ref_arm_635] PDF. On the right, a small permanently attached plate could reinforce the upper half of the shell-like extension [ref_arm_702] PDF. North of the Alps in the second half of the fifteenth century, elbow protection usually took the form of an independent Type II shell [ref_arm_20] PDF.

Originalwortlaut vergleichen
3.1.4 Elbow 



Elbow protections in the shape of discs appear in English artworks from 1260 on.63 Probably 



also leather was molded into a shape similar to a shell and fastened to the point of the elbow. 



The elbow could not be protected by a closely embracing plate, as this would blockade the 



bending of the elbow. To temper this problem, the elbow plate was enlarged with a leaf -



shaped extension [ ref_arm_362] (type -II). To improve the protection, the shell -like 



extensions of the elbow became much larger [ref_arm_52]. On the left arm – when fighting 



with lances on horseback the most exposed body part – a second, larger and thicker elbow 



plate could be optionally attached (type -II reinforce) [ ref_arm_635]. At the right side the 



upper half of the shell-like elbow extension could be covered by a permanently fixed small 



reinforcement plate [ref_arm_702]. North of the Alps in the second half of the 15 th century 



the elbow protection was usually des igned as an independent shell -like plate (type -II) 



[ref_arm_20].
S. 54–55 · Sprachlich überarbeitet · Entwurf

3.1.5 Forearm

A pair of leather forearm defences has recently been excavated [ref_arm_5103] PDF [ref_arm_5104] PDF, and a single example was found in Dordrecht [ref_arm_5121] PDF. Although no images or objects document the first iron or steel versions, their rigidity makes it likely that they initially enclosed only half the arm, Type I.

The earliest surviving Type III forearm protection may be the pieces in the DNM [ref_arm_1027] PDF [ref_arm_1029] PDF. In 2011 these were displayed as separate Type I upper-arm and forearm defences. More probably, they were originally connected by hinges or leather to form a tube enclosing the forearm. Their slightly curved, pointed elbow extensions resemble those shown on mid-fourteenth-century effigies [ref_ill_art_5344] PDF.

A two-part tube provided full forearm coverage. Early examples fitted closely, leaving room for the broad movement of contemporary hand-protection cuffs [ref_arm_980] PDF. From the 1430s, a new Type I hand form [ref_arm_1294] PDF, open on the palm side of the wrist, provided sufficient room for movement without requiring such a slender forearm defence [ref_arm_1277] PDF. Forearm plates could consequently become shorter, broader and less tapered towards the wrist [ref_arm_846] PDF.

Originalwortlaut vergleichen
3.1.5 Lower arm 



A pair of extant lower -arm defenses made of leather has recently been excavated 



[ref_arm_5103] [ ref_arm_5104] and another, single piece was found in Dordrecht



[ref_arm_5121]. Though no images or artifacts are at hand, the first defenses to be made of 



iron or steel plate were most likely encircling the arms only by half (type -I) – due to the 



inflexibility of the material. Probably the oldest existing protections of type -III lower arms 



are preserved in the DNM [ ref_arm_1027] [ref_arm_1029]. In 2011, they were mistakenly 



shown on display as upper and lower arm -protections of type -I, but most likely the parts 



were once attached to each other via hinges or leather so they would form a “tube” entirely 



embracing the lower arm. The slightly bent and pointed elbow-extension of these examples 



can be seen similarly at contemporary effigies of the mid-14th century [ref_ill_art_5344]. 



Instead, the armourer made a tube of two halves for the protection of the entire lower arm 



(type-III). This was close fitting to allow a wide motion -range of the contempor ary hand-



protection-cuff [ref_arm_980]. From the 1430ies on, the cuffs of a new variation of type -I 



hand-protections [ref_arm_1294] – now open at the pulse -side – allowed enough motion -



space for the wrist and did not depend on a lean lower arm defense anymore [ref_arm_1277]. 



Therefore, in the years to follow the lower arms could be modeled shorter in length, wi der 



in circumference and they were less tapered towards the wrist [ref_arm_846].
S. 55–56 · Sprachlich überarbeitet · Entwurf

3.1.6 Systems

In the last quarter of the fourteenth century, probably in Italy, armourers began trying to close the gaps in earlier systems of separate plates, such as [ref_ill_art_5249] PDF (description 2), by linking the elements while preserving movement. The simplest hypothetical solution would be a channel of three plates: upper arm, elbow and forearm. The arm plates would lie inside the elbow plate and articulate with it. Because the elbow plate had to remain over the elbow point, however, the half-tubes above and below could protect only the rear of the arm. Such a construction [ref_ill_sys_arm_hyp] would leave the exposed side undefended and was therefore probably never made.

By the last third of the fourteenth century, Type III forearms and Type II elbows offered a way forward. Italian upper-arm protection nevertheless remained Type I until the 1430s, leaving the front covered only by ring armour. Small articulated lames between the elbow and neighbouring plates closed the gaps that opened during flexion. Sliding rivets allowed the forearm to rotate,64 while articulated riveted joints held the elements together. Because the earliest examples appear to have been made in northern Italy, this arrangement is termed the “Italian system” [ref_ill_sys_arm_ita_auI_aeII_alIII]; see, for example, the arms of [ref_arm_4098] PDF.

During the 1420s, Type II upper-arm plates replaced Type I, and large Type II shoulders were added. The shoulder remained separate, while the other elements were permanently articulated together. With changes in appearance but little alteration to its construction, including the rotating forearm, this system continued in Italian workshops until the early sixteenth century. From the late fifteenth century it was also made in Flanders, although there the forearms did not rotate and additional reinforcements were no longer fitted.

Until around 1500, this arrangement was widely, though not exclusively, used for comparatively costly armour throughout Europe [ref_ill_sys_arm_ita_asII_auII_aeII_alIII] [ref_arm_4143] PDF. From about 1510, Type III elbows could also be fitted to field armour. With the addition of Type III upper-arm protection in the early sixteenth century, the combination of upper arm III, elbow II or III and forearm III superseded other expensive arm systems from the mid-sixteenth century onwards.

Most plate-arm defences in European art of the first half of the fifteenth century appear to follow the Italian system [ref_ill_sys_arm_ita_auI_aeII_alIII]. On the right wing of the Albrechtsaltar, made in Austria around 1437, a pair hangs beneath a Type III helmet [ref_ill_art_5372] PDF (description 1). In a scene showing fighters around Joan of Arc, the figures wear small shoulder and upper-arm defences, both Type I, with small plates at the front of the armpit. These features are associated exclusively with armour made north of the Alps. Many figures probably wear elements of the Italian system beneath their ring-armour sleeves. Other images support the view that small shoulder defences were commonly worn over sleeves concealing the upper-arm plates [ref_ill_art_5176] PDF [ref_ill_art_5238] PDF (description 2).

Alongside these Italian systems, the separate arm defences of the fourteenth century continued to develop north of the Alps without becoming permanently joined. No examples survive from the first half of the fifteenth century, but artworks demonstrate their use. In the same altarpiece, for example, men on either side of the central woman wear separate elbow plates over ring armour [ref_ill_art_5372] PDF (description 2).

Forearm protection could be Type I [ref_ill_art_5195] PDF, but was more commonly fully enclosing, Type III. Since the elbow was connected to the upper-arm and forearm elements only through the underlying ring armour or a leather strap, the forearm could rotate without the complicated mechanism of the Italian system. The disadvantage was the gaps between the plates. This arrangement, not permanently joined at the elbow, is termed the “German system”: it does not appear in Italy but occurs frequently in German-speaking lands and elsewhere in northern and western Europe.

The German system changed during the second half of the fifteenth century. In the 1460s, costly armour generally joined a Type I shoulder permanently to a Type I upper-arm plate and added armpit protection [ref_ill_sys_arm_ger_asI_apit_auI_aeII_alIII]. From the 1470s, larger Type II shoulders were also used, either separate from a Type III upper-arm defence [ref_ill_sys_arm_ger_asII_auIII_aeII_alIII], as on [ref_arm_3257] PDF, or permanently joined to a Type II upper-arm plate [ref_ill_sys_arm_ger_asII_auII_aeII_alIII], as on [ref_arm_3243] PDF.

Another fifteenth-century arrangement, for which no example survives, is known as “jack-chains”. It usually consisted of one or two narrow plate strips along the upper arm and forearm, joined by a simple elbow plate [ref_ill_art_5166] PDF [ref_ill_art_5202] PDF [ref_ill_art_5282] PDF [ref_ill_art_5304] PDF [ref_ill_art_5309] PDF (description 1).

Originalwortlaut vergleichen
3.1.6 Systems 



By the last quarter of the 14th century, it was probably the Italian armourers that tried to keep 



the chinks at the o lder systems made of single plates (e. g. [ ref_ill_art_5249] (descr. 2)) 



closed by fixing them together in a way that would still allow certain mobility. The simplest 



solution would basically be a groove, consisting of three plates: one for the upper arm, one 



for the elbow and one for the lower arm. The arm -plates would lie inside the elbow -plate 



and they could be bent like the human elbow. As the elbow -plate would have to be placed 



invariably exactly at the elbow -point, the iron half -pipes of the upper and the lower arm 



could only protect the rear side of the arm. Such a hypothetical arm -protection 



[ref_ill_sys_arm_hyp] – leaving the attacked side of the body exposed – made no sense and 



was therefore probably never produced.  



Probably to temper with these problems, already by the last third of the 14 th century the 



armourers protected the lower arm by defenses of type -III and elbows of type -II. 



Nevertheless, at Italian armour the upper arm until the 1430ies was still of type-I, which left 



the front-side to be protected by ring -armour only. To avoid chinks between the elbow and 



the plates – opening when the elbow was bent – the armourers placed small articulated lames 



in between them. By sliding rivets64 they made the lower arm pivotable. All parts now were 



held together by articulated rivet -joints. Due to the first appearance of this arrangement at 



arm defenses most likely made in northern Italy, this might be called the “Italian system” 



[ref_ill_sys_arm_ita_auI_aeII_alIII] (see for example the arms of the suit [ref_arm_4098]).  



In the 1420ies the armourers replaced type-I by type-II upper arms. Furthermore, they added 



large shoulder defenses of type -II. While all other parts of the Italian system were 



permanently connected to each other, the shoulder defenses were always separate and usually 



of type-II. This system of complete arm defense – with variations in design only – including 



the revolving lower arms – was produced in the Italian workshops unaltered until the early 



16th century. From the late 15 th century on it was also produc ed in Flanders – but there the 



lower arms were not pivotable and no reinforcements were attached anymore. Until about 



1500 basically the same system of full arm -protection was used – though not exclusively – 



throughout all Europe on the rather costly armour [ref_ill_sys_arm_ita_asII_auII_aeII_alIII] 



[ref_arm_4143]. From about 15 10 on, also at field armour the elbows could optionally be 



made of type-III. In the early 16 th century an upper arm defense of type -III was added and



this constellation (upper arm III, elbow II or III and lower arm III) was the one to supersede 



all other costly armour systems from the mid-16th century on. 



The majority of all plate arm defenses depicted in European artworks of the first half of the 



15th century seem to be of the Italian system [ ref_ill_sys_arm_ita_auI_aeII_alIII]. For 



example, a pair of such arm -protections is depicted hanging below a helmet of type -III on 



the right wing of the Albrechtsaltar, made in Austria about 143 7 [ref_ill_art_5372] (descr. 



1). A group of fighters is standing around the figure of Jean d’Arc. All protagonists in the 



scene are armoured and each wears rather small protections coverin g the point of the 



shoulders (type -I) and parts of the upper arm (type -I). To protect the underside of the 



shoulder, small plates are placed at the front of the armpit. All these features are found 



exclusively at armour made north of the Alps. It is likely  that many of them wear arm -



protections of this system underneath the ring -armour sleeves. Many other depictions 



support the assumption that north of the Alps the small shoulder defenses were typically 



worn upon a ring -armour sleeve, which covered the uppe r arm of an Italian -system 



[ref_ill_art_5176] [ref_ill_art_5238] (descr. 2).  



Nevertheless, in parallel to these “Italian” systems, in northern alpine Europe the separate 



arm defenses of the 14 th century (e. g. [ref_ill_art_5249] (descr. 2)) were developed further 



without becoming permanently connect ed. From the first half of the 15 th century no 



examples that could tell about the tradition of the older system do survive, but artworks show 



that it was obviously in use. For example the men to the left and to the right of the lady in 



the aforesaid altarp iece [ ref_ill_art_5372] (descr. 2) obviously wear separate elbow 



protections upon a ring-armour shirt.  



The lower arms were either of type -I [ref_ill_art_5195] but more commonly completely 



closed (type-III). As the elbow was connected to the upper and the lower arm only by the 



ring-armour underneath or a band of leather, the lower arm could easily be turned. A 



complicated r evolving system as found on the Italian systems was not necessary. A 



disadvantage was the chinks between the plates. The complete arm -defense system 



consisting of parts not permanently joined at the elbow might be called the “German System” 



– as it never appeared in Italy but frequently in the German speaking lands (but also in other 



western and northern European regions). In the second half of the 15 th century this system 



experienced some alterations. In the 1460ies the type -I shoulder defense at costly ar mour 



was usually permanently fixed to an upper arm defense of type -I with armpit protections 



attached [ref_ill_sys_arm_ger_asI_apit_auI_aeII_alIII]. From the 1470ies on also the larger 



type-II shoulders could be added, either separate from a type -III upper arm defense 



[ref_ill_sys_arm_ger_asII_auIII_aeII_alIII] (see for example the arms of the suit 



[ref_arm_3257]) or permanently connected to an upper arm of type -II 



[ref_ill_sys_arm_ger_asII_auII_aeII_alIII] (see for example the arms of the suit 



[ref_arm_3243]).  



The 15 th century knew also another arm defense system which did not survive in any 



example: The so called “jack-chains”. This was usually only consisting of one or two narrow 



plate straps at the upper and at the lower arm with a simple plate at the elbow 



[ref_ill_art_5166] [ref_ill_art_5202] [ref_ill_art_5282] [ref_ill_art_5304] [ref_ill_art_5309] 



(descr. 1).
S. 56–58 · Sprachlich überarbeitet · Entwurf

3.2 Hand protection

Relatively few scholars have concentrated specifically on hand protection.65 Separate hand defences did not exist before the late twelfth century. The earliest were made of ring armour, sometimes probably continuous with the sleeves of a shirt [ref_ill_art_5390] PDF [ref_ill_art_5374] PDF (description 1). From the second half of the thirteenth century, plate discs were occasionally added over the back of the hand [ref_ill_art_5377] PDF.

The origins of segmented hand protection remain uncertain. Neither late medieval segmented nor plate hand protection covered the palm with plates. Excavated examples have small plates riveted inside an outer textile covering. The earliest finds date from the mid-fourteenth century and differ slightly in construction,66 making it difficult to determine whether established types already existed. Images suggest that larger segments were used in comparable arrangements during the first half of that century [ref_ill_art_5234] PDF. Surviving objects nevertheless suggest considerable individual variation.

Several excavated examples combine small segments with a larger plate over the back of the hand. Some of these larger plates are flat [ref_arm_1281] PDF [ref_arm_1340] PDF; others imitate the contours of the hand through embossing [ref_arm_1341] PDF [ref_arm_1336] PDF [ref_arm_1337] PDF.

The first clearly recognisable group of plate hand protection is commonly called “hour-glass” after its shape. Armourers probably sought a light construction with as few gaps as possible. A broad, flaring cuff allowed the wrist to move freely [ref_arm_1306] PDF [ref_arm_1307] PDF [ref_arm_4859] PDF. From around 1420, another Type I form replaced it: the cuff extended farther up the back of the forearm [ref_arm_1296] PDF, while only a narrow plate bridge closed the palm side of the wrist. This allowed the hand to bend naturally.

In German-speaking lands during the 1430s and 1440s, Type I hand protection was relatively large and usually protected the finger roots only through an extended metacarpal plate [ref_ill_art_5257] PDF [ref_arm_1291] PDF [ref_arm_1310] PDF. A transitional form appears in [ref_ill_art_5223] PDF (description 2). In Italy, modified Type I forms with much longer pointed cuffs and articulated finger protection remained in use until the end of the fifteenth century [ref_arm_1157] PDF.

Type II developed alongside these forms in Italy from the 1420s [ref_arm_1037] PDF [ref_arm_1148] PDF [ref_arm_1150] PDF. Like other Italian hand protection, it remained relatively stiff at the wrist. Bending the hand opened a vulnerable gap between cuff and forearm, a problem Italian armourers never satisfactorily resolved. Production ceased after 1500.

By the mid-fifteenth century, German-speaking armourers were again using smaller plates. Unlike the earlier segmented forms, these plates overlapped and were joined directly, allowing translational movement of the hand while fitting closely. The chief aim may have been to connect hand and forearm protection securely. An early example, possibly Type III, is depicted in [ref_ill_art_5332] PDF. It already shows the essential advantage over Italian forms: the cuffs of all surviving examples from the second half of the fifteenth century could be fastened directly to the forearm protection, preserving movement without opening a vulnerable gap [ref_arm_1061] PDF [ref_arm_1126] PDF [ref_arm_1082] PDF. Type III variants were still occasionally made in the 1580s, for example for armour M99 in the SKD.

In the 1480s, armourers found that a separate wrist plate was not necessary for free hand movement. The metacarpal plates could be joined directly to the cuff, producing Type IV [ref_arm_1228] PDF [ref_arm_1272] PDF. Italian, Spanish and Flemish examples remained relatively stiff, with broad cuffs unattached to the forearm protection [ref_arm_1185] PDF [ref_arm_1222] PDF. Type IV became usual on field armour from the sixteenth to the mid-seventeenth century. From the 1480s, some fully closed cuffs extended to the elbow and themselves served as complete Type III forearm protection [ref_arm_1250] PDF [ref_arm_1244] PDF [ref_arm_1199] PDF.

Redaktionelle Hinweise · 2
  • Mehrere Chronologien weichen von Kapitel 2 ab, insbesondere Type II ab 1420 statt ca. 1440 und Type III noch in den 1580ern. Aussagen beider Kapitel erhalten; fachliche Harmonisierung offen.
  • „Translational movement“ wie im Handtypenabschnitt vorerst erhalten; die genaue Bewegungsbeschreibung bleibt zu klären.
Originalwortlaut vergleichen
3.2 Hand-protection 



Only few scholars had focused their research particularly on hand-protections.65 A separate 



hand-protection did not exist before the late 12 th century. The first defenses were made of



ring-armour, in some cases probably connected to the sleeves of a ring -armour shirt 



[ref_ill_art_5390] [ref_ill_art_5374] (descr. 1). From the second half of the 13 th century to 



such protections plate -discs were occasionally fastened to t he back of the hand 



[ref_ill_art_5377]. The beginnings of segmented armour for the protection of the hand 



remain obscure. It has to be noted that at all late medieval segmented - and plate -hand-



protections the inner side of the hand was never protected by plates. Excavated examples 



show that smaller plate segments were riveted into an exterior fabric cover. The oldest finds 



date from the mid-14th century and all are slightly different in the ir construction. 66 It is 



therefore difficult to tell if certain types had already been developed. Contemporary artworks 



indicate that in the first half of the 14 th century some different variations were made in a 



similar way from larger segments [ ref_ill_art_5234]. Nevertheless, according to extant 



examples, segmented hand -protections were made rather individually. Several excavated 



examples are merely constructed from small segments with a large plate covering the back 



of the hand. While some of these plates were left plane [ ref_arm_1281] [ref_arm_1340], at 



others the natural shape of the back of the hand was imitated by embossing [ref_arm_1341] 



[ref_arm_1336] [ref_arm_1337].  



The first type of plate hand-protection that clearly defines a group of similar objects is called 



“hour-glass hand-protection” – the name derives from its characteristic shape. The intention 



of the armourer was probably to produce a light hand-protection with as little gaps between 



the plates as possible. The cuff was widely flaring out so the wrist could move freely 



[ref_arm_1306] [ ref_arm_1307] [ ref_arm_4859]. This variation from 1420 on was 



superseded by another type -I hand-protection, where the cuff reached further up the lower 



arm at the back -of-the-hand side [ ref_arm_1296]. At the pulse-side these hand -protections 



were closed by only a thin plate -bridge. This construction allowed for a natural angling of 



the wrist. In the German speaking lands the hand -protections of type-I from the 1430ies to 



the 1440ies were rather large and usually had only the extended metacarpal plate to protect 



parts of the fingers [ ref_ill_art_5257] [ ref_arm_1291] [ ref_arm_1310]. An illustrative 



transitional type-I variation is depicted on [ ref_ill_art_5223] (descr. 2). In Italy the type -I 



hand-protection with some alterati ons – a much longer, pointed cuff and articulated finger 



protections – remained in use until the end of the 15th century [ref_arm_1157].  



In parallel from the 1420ies on – exclusively in Italy – hand-protections of type-II were made 



[ref_arm_1037] [ref_arm_1148] [ref_arm_1150]. This type was still ve ry inflexible at the 



wrist, just like all Italian hand -protections. When the hand was angled, at all models a 



dangerous gap opened between the cuff and the lower arm – a problem never satisfactorily 



solved by the Italian armourers. After 1500 these hand -protections were not produced 



anymore. 



By the mid-15th century in the German speaking lands hand-protections of smaller segments 



were produced again. Unlike the 14 th century segmented-armour examples now the plates 



were overlapping and joined directly to each other, allowing for a translational motion of the 



entire hand while the plates were still close fitting. Probably the main intention of turning 



back to smaller segments was to safely connect the hand -protection to the lower arm. An 



early example of such a hand-protection, possibly of type-III, is seen on [ref_ill_art_5332]. 



Already at this model the most important feature that made these hand -protections superior 



to the Italian models is evident: The cuffs of all extant examples of the second half of the 



15th century could be fastened directly to the lower arm. No dangerous gaps opened while at 



the same time the hand could move freely [ref_arm_1061] [ref_arm_1126] [ref_arm_1082].



V ariations of type-III hand-protections were still occasionally made until the 1580ies (e. g. 



for the Armour M99 of the SKD).  



In the 80ies of the 15 th century the armourers found that for a free motion of the hand the 



wrist-plate of type -III hand -protections was obsolete. Now the metacarpal plates were 



directly joined to the cuff (type-IV) [ref_arm_1228] [ref_arm_1272]. The Italian, Spanish or 



Flemish models were still rather stiff at the wrist, the cuff was still very wide and not fastened 



to the lower arm [ref_arm_1185] [ref_arm_1222]. A suit of field armour from the 16th until 



the mid-17th century was usually equipped with type -IV hand -protections. The entirely  



closed cuffs of some examples from the 1480ies on reached to the elbow and thus they served 



as a full lower arm-protection of type-III [ref_arm_1250] [ref_arm_1244] [ref_arm_1199].
S. 58 · Sprachlich überarbeitet · Entwurf

3.2.1 Finger and thumb protection

Classifying finger-protection systems is particularly difficult because most surviving late medieval hand defences have lost their original finger elements. A single hand type could carry several different finger and thumb arrangements. Once articulated finger lames developed during the fourteenth century, many systems probably coexisted throughout the second half of the fifteenth century. Missing components often prevent their original construction from being established.

The differences are therefore defined chiefly through drawings rather than lengthy descriptions. The illustrations show common systems; further variants certainly existed. Three broad groups are distinguished: separate protection for each finger, shared protection in which one plate covers at least two fingers, and systems combining these principles.

Redaktionelle Hinweise · 1
  • Keine neue Typzuordnung für die zurückgestellten Daumensysteme ergänzt. Die allgemeine Aussage des Ausgangstexts bleibt erhalten.
Originalwortlaut vergleichen
3.2.1 Finger and thumb protection  



The definition of different systems for the protections of the fingers is a very difficult task. 



Most of the extant late medieval hand -protections have lost the original finger parts. Hand-



protections of the same type could be equipped with different types of finger and thumb 



protections. After articulated finger -lames had been developed from the 14 th century on, 



many systems had probably been used in pa rallel throughout the second half of the 15 th 



century. On many extant hand -protections the finger parts are lost, thus it often cannot be 



determined how the fingers of an extant hand-protection were constructed. As many systems 



do exist and descriptions would be too confusing, the definition of the differences is reduced 



to illustrations. These illustrations describe the common systems – some further construction 



variations certainly existed.  



In the following the finger protection systems will be split int o three large groups: The 



systems where each finger is protected separately (fingered hand -protections), the systems 



where at least two fingers are covered by one plate (mitten hand-protection) and systems that 



combined both characteristics.
S. 58 · Sprachlich überarbeitet · Entwurf

3.2.1.1 Individually protected fingers

On the earliest surviving segmented hand protection, each finger carries small overlapping scales, system a [ref_ill_sys_fin_a] [ref_arm_1341] PDF. The same arrangement occurs on later objects [ref_arm_1080] PDF [ref_arm_1074] PDF, although both may have later replacement finger elements. During the second half of the fourteenth century, small directly adjoining plates could also follow the same basic arrangement [ref_arm_1343] PDF.

Separate plates for the finger bones and joints were made for [ref_arm_1340] PDF in the mid-fourteenth century.67 The fingers of [ref_arm_1150] PDF and [ref_arm_1165] PDF use a distinctive construction: most segments are riveted inside the covering material, but the fingertip plates are attached outside.

From the 1450s, German-speaking armourers generally added a separate lame over the knuckles at the finger roots, overlapping the neighbouring plates. This feature persisted, with variations in appearance, until the mid-seventeenth century. The rest of the finger construction varied considerably. Systems with separately protected fingers include i [ref_ill_sys_fin_i] [ref_arm_1118] PDF, h [ref_ill_sys_fin_h] [ref_arm_1071] PDF, j [ref_ill_sys_fin_j] [ref_arm_4904] PDF [ref_arm_1059] PDF [ref_arm_1090] PDF68 and k [ref_ill_sys_fin_k] [ref_arm_1096] PDF.

Redaktionelle Hinweise · 1
  • Systembuchstaben folgen unverändert dem Fließtext. Abweichende Katalogfelder sind im Atlas bereits gekennzeichnet; hier keine stille Umnummerierung.
Originalwortlaut vergleichen
3.2.1.1 Fingered hand-protections 



At the oldest extant segment -hand-protection each of the fingers was protected by small 



overlapping scales (type-a) [ref_ill_sys_fin_a] [ref_arm_1341]. This system was also used 



in later times [ref_arm_1080] [ref_arm_1074] (at both items probably later completions). In 



the second half of the 14th century each finger could be protected by small, directly adjoined 



plates basically also arranged like type -a [ref_arm_1343]. In the mid-14th century single 



plates for the finger -bones and the finger -joints were made for the hand -protection 



[ref_arm_1340]67. Of a unique system are the fingers at [ref_arm_1150] and [ref_arm_1165], 



where segments are riveted interiorly and the plates for the points of the fingers exteriorly to 



a lining cover. From the 1450ies on in the German speaking lands the knuckl es at the roots 



of the fingers were usually protected by a separate single lame that lay upon the other plates, 



a feature found on hand-protections with variations in design until the mid-17th century. The 



construction of the remaining plates for the prote ction of the fingers varied widely. Fingers 



could be protected separately but by different systems:  



- Type-i [ref_ill_sys_fin_i] [ref_arm_1118] 



- Type-h [ref_ill_sys_fin_h] [ref_arm_1071]  



- Type-j [ref_ill_sys_fin_j] [ref_arm_4904] [ref_arm_1059] [ref_arm_1090]68 



- Type-k [ref_ill_sys_fin_k] [ref_arm_1096]
S. 59 · Sprachlich überarbeitet · Entwurf

3.2.1.2 Shared finger protection

From the early fifteenth century, some metacarpal plates extended a short distance over the fingers, system b [ref_ill_sys_fin_b] [ref_arm_1308] PDF. Ring armour often protected the fingers and thumbs of such mitten forms [ref_ill_art_5276] PDF. The earliest surviving examples retaining these ring-armour elements are probably [ref_arm_1178] PDF.

From the 1440s, Italian hand protection could cover all the fingers with one articulated lame, system e [ref_ill_sys_fin_e] [ref_arm_1156] PDF, or two, system f [ref_ill_sys_fin_f] [ref_arm_1160] PDF. From the mid-fifteenth century, shared finger protection in German-speaking regions could also have a separate knuckle lame overlapping the other plates. The fingers might then be covered by one lame, system l [ref_ill_sys_fin_l] [ref_arm_1076] PDF, or several, system m [ref_ill_sys_fin_m] [ref_arm_1135] PDF. Protection grouping the fingers in pairs was also common, system n [ref_ill_sys_fin_n] [ref_arm_1245] PDF [ref_ill_art_5383] PDF (description 2).

Italian hand forms were occasionally fitted with similar finger lames, as on the Type II example depicted in [ref_ill_art_5194] PDF. Paired finger protection continued into the early sixteenth century [ref_ill_art_5171] PDF. By the late fifteenth century, lames were sometimes combined with ring armour [ref_ill_art_5229] PDF; a surviving example combines both materials with the fingers divided into pairs [ref_arm_1061] PDF.

Originalwortlaut vergleichen
3.2.1.2 Mitten hand-protections 



From the early 15th century some hand-protections had the metacarpal plate extended a bit 



towards the points of the fingers (type-b) [ref_ill_sys_fin_b] [ref_arm_1308]. The fingers 



and the thumbs of some mitten hand -protections were often protected by ring -armour 



[ref_ill_art_5276]. The oldest extant examples stil l retaining the ring -armour parts are 



probably [ref_arm_1178]. From the 1440ies on the fingers of Italian hand-protections could 



be protected by one (type-e) [ref_ill_sys_fin_e] [ref_arm_1156] or two (type-f) 



[ref_ill_sys_fin_f] [ref_arm_1160] articulated lames covering all fingers together. From the 



mid-15th century on in the German speaking lands also at mitten hand -protections the 



knuckles at the roots of the fingers could be protected by a separate single lame that lay upon 



the other plates. Also here the fingers could be protected by one (type-l) [ref_ill_sys_fin_l] 



[ref_arm_1076] or optionally several lames (type-m) [ref_ill_sys_fin_m] [ref_arm_1135], 



but also h and-protections with pair -wise protected fingers were very common (type-n) 



[ref_ill_sys_fin_n] [ref_arm_1245] [ ref_ill_art_5383] (descr. 2). Also Italian hand -



protection models were occasionally equipped with such finger -lames [ ref_ill_art_5194] 



(here type -II). Finger protections split in pairs were used until the early 16 th century 



[ref_ill_art_5171]. By the late 15 th century some finger -lames were combined with ring -



armour [ ref_ill_art_5229]. Even a combination of lames and ring -armour fingers split in 



pairs still exists [ref_arm_1061].
S. 59 · Sprachlich überarbeitet · Entwurf

3.2.1.3 Combined systems

During the first half of the fifteenth century, Italian armourers favoured a construction combining an extended metacarpal plate with directly attached small finger scales, system c [ref_ill_sys_fin_c] [ref_arm_1148] PDF.69 The first finger lame could alternatively be separately articulated, producing system d [ref_ill_sys_fin_d].

Originalwortlaut vergleichen
3.2.1.3 Combined systems 



In the first half of the 15 th century the Italian armourers favored a finger system that 



combined an elongated metacarpal plate with directly attached small scales for the fingers 



(type-c) [ref_ill_sys_fin_c] [ref_arm_1148]69.Optionally the first finger lame could also be 



articulated (type-d) [ref_ill_sys_fin_d].
S. 59 · Sprachlich überarbeitet · Entwurf

3.3 Head protection

Helmets were the first armour objects made from a single large plate. The Roman legions of the late Republic already used single-plate iron helmets, including the form named after the Weisenau find site. Migration-period helmets were assembled from several riveted plates, the so-called “Spangenhelm” and “Bandhelm”. From the eleventh century, one-piece Type I helmets, usually with nasal guards, were used in eastern and western Europe.

The pivoting visor was probably introduced in the late thirteenth century. Claude Blair cites the will of Odo de Roussillon, dated 1298, which mentions a heaume a vissere.70 Early images of pivoting face-guards date to around 1320 [ref_ill_art_5190] PDF [ref_ill_art_5169] PDF [ref_ill_art_5292] PDF [ref_ill_art_5343] PDF (description 2). The earliest surviving helmets fitted with them, however, are in the style of the last third of the fourteenth century [ref_arm_1495] PDF.

Originalwortlaut vergleichen
3.3 Head-protection 



Helmets are the first armour items to be made of one single larger plate. Already the late -



republic roman legions used helmets made of a single iron plate, for example a certain type 



called after an important find -site “Weisenau-helmet”. The migration period knew only 



helmets riveted together from several plates, the so called “Spangenhelm” and the 



“Bandhelm”. From the 11 th century on a helmet of type -I worked in one piece, usually 



equipped with a nasal-guard, was in use in Eastern and Western Europe.  



The pivoting visor is probably an invention of the late 13 th century. Claude Blair refers to 



the will of Odo de Roussillon (1298) , where a  heaume a vissere is mentioned. 70 Early 



illuminations of helmets with pivoting face -guards date about 1320: [ ref_ill_art_5190] 



[ref_ill_art_5169] [ ref_ill_art_5292] [ ref_ill_art_5343] (descr. 2) – but the oldest extant 



helmets to be equipped with such a face -guard are made in the style of the last third of the 



14th century [ref_arm_1495].
S. 59–60 · Sprachlich überarbeitet · Entwurf

3.3.1 Type I

Type I is the simplest form of one-piece helmet, with two principal skull shapes: pointed and hemispherical. A distinctive example in the SNZ [ref_arm_2093] PDF provides a useful starting point. It has a pointed skull but already carries a detachable nasal guard, developing from earlier fixed nasals and anticipating the visor attachments of Types IV and V.

Only two other pointed Type I helmets from the period survive [ref_arm_1607] PDF [ref_arm_1608] PDF. Their small nasal projections are formed by concave cut-outs above the eyes. The burred lower edges may indicate that lower plates were once attached, in which case they would belong to Type V; compare [ref_arm_2167] PDF.

The most common form has a simple hemispherical skull [ref_arm_1622] PDF [ref_arm_4265] PDF. Many survive, although not all were examined closely here. Production probably extended from the thirteenth to the seventeenth century. Their simplicity often leaves few features by which individual objects can be dated precisely.

Some examples, probably from the first half of the fifteenth century, have slight cut-outs above the ears [ref_arm_1621] PDF [ref_arm_1624] PDF [ref_arm_4468] PDF. Another probably contemporary form turns these ear cut-outs outwards and also has cut-outs above the eyes [ref_arm_1618] PDF [ref_arm_1619] PDF [ref_arm_4625] PDF.

One-piece hemispherical forms remained in use alongside other plate-armour types until the mid-sixteenth century, whereas pointed Type I skulls were no longer made in the fifteenth century. Hemispherical forms were probably easier to produce and were lighter and closer fitting, allowing a ring-armour cap, another helmet or a hat to be worn over them. Their chief disadvantage was the absence of protection for the lower head.

Originalwortlaut vergleichen
3.3.1 Type-I 



Type-I helmets are the most simple types  of all single -piece helmets. Generally two 



variations exist: one with a pointed and another one with a half-bowl shaped skull. A unique 



item in the SNZ [ref_arm_2093] is probably the best example to start the discussion of late 



medieval helmets of type -I. This example still has a pointed skull, but is already equipped 



with a detachable nasal-guard – a predecessor of later visor attachment systems (at type -IV



and -V helmets) and a follower of earlier helmets  with a fixed nasal-guard. Only two more 



type-I helmets of the considered period with pointed skulls are extant [ ref_arm_1607] 



[ref_arm_1608], but they have  only a small nasal -guard formed by two concave cutouts 



above each eye. Due to the burred lower edge it is well possible that these two helmets 



originally had a lower plate attached and would therefore rather count as helmets of type -V 



(compare [ref_arm_2167]).  



The most common model has a simple half -bowl shaped skull [ ref_arm_1622] 



[ref_arm_4265]. Many examples do exist but not all of them were examined closer for this 



study. They were probably produced from the 13 th to the 17 th century. Many are so simple 



there are not many features that allow an exact dating of specific items. Some variations, 



probably of the first half of the 15 th century show slight cutouts above the ears 



[ref_arm_1621] [ref_arm_1624] [ref_arm_4468]. Another model, most likely from the same 



period shows a significant feature: the cutouts above the ears are angled  outwards and the 



plate is also cut out above each eye [ ref_arm_1618] [ ref_arm_1619] [ ref_arm_4625]. 



Hemispheric shaped helmets of type-I made of one piece remained in parallel use throughout 



all the plate -armour period until the mid-16th century, but in the 15 th century the pointed -



skull model was not produced anymore. The production of the half -bowl variatio n was 



probably easier. These models were also lighter and more close -fitting so a cap of ring -



armour, a second helmet or a hat could be worn upon it. The main disadvantage of all type-



I helmets was that they did not protect the lower parts of the head.
S. 60 · Sprachlich überarbeitet · Entwurf

3.3.2 Type II

Until the late fourteenth century, western European Type II field helmets were still assembled from several riveted plates [ref_arm_1443] PDF [ref_arm_1456] PDF [ref_arm_1457] PDF. They were the first helmets since those of ancient gladiators to cover the entire head and face, and part of the neck, with plates. The depth required was probably too difficult to forge from a single plate. From the late fourteenth century, these forms developed into the frog-mouthed Type VIII helmets generally used only for tournaments [ref_arm_1645] PDF.

Probably in the first half of the fifteenth century, the Aegean region produced a final field variant of Type II, with a pivoting face-guard and articulated right cheek-guard [ref_arm_1445] PDF [ref_arm_1458] PDF. Their size made them uncomfortable for fighting on foot. A changing preference for curved, tapered skulls may also have contributed to their disappearance from battlefields around the mid-fifteenth century.

Originalwortlaut vergleichen
3.3.2 Type-II 



Until the late 14 th century the skulls of western European type -II helmets for the field use 



were still made of several segments fixed together by rivets [ref_arm_1443] [ref_arm_1456] 



[ref_arm_1457]. This type was the first helmet since the antique “Gladiator’s helmets” to 



cover all the head, the face and to a limited extend a lso the neck by plates. Probably due to 



the difficulties of forging such deep helmets out of one plate, they were made from segments. 



From the late 14th century on type-II helmets developed into frog-mouthed helmets of type-



VIII which were usually worn in the tournament only [ref_arm_1645].  



Probably in the first half of the 15th century in the Aegean Region a last war-variant of type-



II helmets with a pivotable face -guard and an articulated guard at the rig ht cheek was 



developed [ref_arm_1445] [ref_arm_1458]. One disadvantage of these helmets was that due 



to their large dimensions they were uncomfortable for f ighting on foot. Another factor that 



might have led to their disappearance off the battlefields about the mid-15th century was 



possibly their pointed silhouette being not fashionable anymore. The fighters were now 



looking for helmets with curvy, tapered skulls.
S. 60–61 · Sprachlich überarbeitet · Entwurf

3.3.3 Type III

Images indicate that Type III helmets—whose variants are called “kettle hats”, “capacete” and “morion”—were initially assembled from segments in the thirteenth century. A later example appears in an Italian painting of the mid-fourteenth century [ref_ill_art_5184] PDF. Several probably fourteenth-century segmented examples survive in Scandinavia [ref_arm_1422] PDF [ref_arm_4380] PDF [ref_arm_4579] PDF [ref_arm_4174] PDF. Other variants have been excavated in Germany [ref_arm_1367] PDF [ref_arm_1440] PDF, Italy [ref_arm_4345] PDF and the Netherlands [ref_arm_4251] PDF.

By the end of the fourteenth century, Type III helmets were usually made from one plate. Forms with a small projection at the front of the brim may be among the earliest [ref_arm_1362] PDF [ref_arm_1401] PDF [ref_arm_1414] PDF. With changes in appearance, they continued into the early sixteenth century [ref_arm_1398] PDF [ref_ill_art_5149] PDF. Another form, used from the 1430s [ref_arm_1347] PDF [ref_arm_1368] PDF [ref_arm_1441] PDF to around 1480 [ref_arm_4264] PDF, resembles a top hat with a medial ridge or pointed crown.

A distinctive form, probably developed in Italy in the first half of the fifteenth century, carries a medial ridge from the pointed front of the brim to its rear point [ref_arm_1353] PDF. Other forms have steep brims beside the ears and slightly tapered skulls [ref_arm_1377] PDF. The so-called Burgundian kettle hat [ref_arm_1349] PDF [ref_arm_1424] PDF [ref_arm_4197] PDF occurs not only in Burgundian art but also elsewhere, including Spain [ref_ill_art_5183] PDF. Spanish soldiers in the last third of the fifteenth century often wore the variant called “capacete” [ref_arm_1413] PDF [ref_arm_4184] PDF [ref_arm_5102] PDF.

The unusual example [ref_arm_4464] PDF71 has no surviving parallel, although contemporary art indicates that such forms existed in the mid-fifteenth century [ref_ill_art_5347] PDF. The upturned front brim of [ref_arm_1380] PDF, around 1500, is likewise exceptional and imitates a textile hat.

Contrary to a common assumption, Type III helmets were not confined to foot soldiers. Mounted men-at-arms also wore them [ref_ill_art_5255] PDF (description 2) [ref_ill_art_5200] PDF. They generally resemble ordinary civilian brimmed hats [ref_ill_art_5357] PDF. With the face and field of vision unobstructed, they were well suited to fighters who needed to aim projectile weapons. They chiefly protected against blows from above, while the brim offered some coverage to the shoulders. Different variants remained in use until the mid-seventeenth century.72

Originalwortlaut vergleichen
3.3.3 Type-III 



Type-III helmets, variations are called “kettle hats”, “capacete” or “morion”, according to 



depictions in the 13 th century were initially made from segments. A late example is shown 



on an Italian painting of the mid-14th century [ref_ill_art_5184]. In different Scandinavian 



countries several of such helmets, probably of the 14 th century, survived [ ref_arm_1422] 



[ref_arm_4380] [ ref_arm_4579] [ ref_arm_4174]. Also in Germany [ ref_arm_1367] 



[ref_arm_1440], Italy [ ref_arm_4345] and the Netherlands [ ref_arm_4251] different 



segmented variations were excavated. By the end of the 14 th century type-III helmets were 



usually made of one plate. Probably the earliest examples are variations with a small nose at 



the front of the brim [ref_arm_1362] [ref_arm_1401] [ref_arm_1414]. They were made with 



some alterations in design until the early 16 th century [ref_arm_1398] [ref_ill_art_5149]. 



Another model used from the 1430ies [ref_arm_1347] [ref_arm_1368] [ref_arm_1441] until 



1480 ca. [ref_arm_4264] is basically of the shape of a top-hat with a medial ridge or a point



at the top. I n the first half of the 15 th century, probably in Italy a unique model developed 



with a medial ridge passing from the frontal pointed brim to the rear point of the brim 



[ref_arm_1353]. At other variations the brim at the ears is rather steep and the skull is slightly 



tapered [ ref_arm_1377]. This so called “Burgundian” type of kettle hat [ ref_arm_1349] 



[ref_arm_1424] [ref_arm_4197] is actually not only shown in Burgundian artworks but also 



in artworks of other cultural regions, e. g. in Spain [ ref_ill_art_5183]. The Spanish soldiers 



in the last third of the 15 th century often wore a special variation called “capacete” 



[ref_arm_1413] [ ref_arm_4184] [ ref_arm_5102]. An absolute unique type-III model is 



[ref_arm_4464]71, while according to contemporary artworks [ ref_ill_art_5347] such 



helmets really existed in the mid-15th century. The helmet [ref_arm_1380] of about 1500 is 



singular in its upward bending frontal brim. It is clear that the armourer tried to imitate a 



textile hat. Helmets of type -III are – unlike often suggested – not necessarily foot soldier’s 



equipment only. Also some men -at-arms on horseback wear helmets of t ype-III 



[ref_ill_art_5255] (descr. 2) [ref_ill_art_5200]. They probably generally resemble the simple 



brimmed hat of the  civilian clothing [ ref_ill_art_5357]. The face and the vision were left 



uncovered, which made this helmet a perfect model for all fighters that needed to aim with 



ballistic weapons. Their defensive function is obvious – the head was protected merely from 



blows from above, the brim to a certain extend protected also the shoulders – and therefore 



different variations remained in use until the mid-17th century.72
S. 61 · Sprachlich überarbeitet · Entwurf

3.3.4 Type IV

During the first half of the fourteenth century, armourers extended the plate at the nape of Type I helmets, developing Type IV. The lower edge gradually descended [ref_arm_1518] PDF [ref_arm_1541] PDF until it covered the nape and cheeks. A ring-armour collar was frequently attached to protect the neck [ref_arm_1501] PDF. Surviving objects and images show pointed skulls, resembling contemporary hoods, by at least 1380.

A detachable articulated face-guard was commonly added in the last quarter of the century [ref_arm_1494] PDF. Detachable nasal guards appear on numerous effigies, including German [ref_ill_art_5267] PDF and Italian examples [ref_ill_art_5284] PDF. Only one example appears to survive [ref_arm_4424] PDF,73 apart from the additional case noted below.

A pointed visor with vision slits probably developed in Italy, usually pivoting at the sides of the skull. Centrally pivoted visors, often attributed to Germany, could also have pronounced projecting snouts, as suggested by [ref_ill_art_5258] PDF. Less pointed forms occur frequently on effigies north of the Alps, including [ref_ill_art_5271] PDF. Their shape gave rise to the term “houndskull-basinet”.

The visors were detachable, probably making the helmet more comfortable when immediate danger had passed. Centrally attached face-guards seem to have gone out of fashion in the early fifteenth century, while side-pivoted forms continued into the 1440s. The inability to lock the visor was probably a disadvantage: an upward blow could expose the wearer’s face.

Originalwortlaut vergleichen
3.3.4 Type-IV 



In the first half of the 14th century the armourers tried to improve the protective functions of 



type-I helmets. First they left the plate a bit longer at the nape (type -IV). The lower edge 



continually moved more down [ ref_arm_1518] [ref_arm_1541] until it covered the entire 



nape and the cheeks. To the lower edge – for the protection of the neck – now frequently a 



collar made of ring -armour was attached [ ref_arm_1501]. At least from 1380 according to 



extant examples and depictions the skulls were pointed, resembling a contemporary hood. 



By the last quarter of the century an articulated detachable face-guard was frequently added 



[ref_arm_1494]. Examples for the detachable application of a nasal guard is depicted at 



many effigies: e. g. in Germany [ref_ill_art_5267] and in Italy [ref_ill_art_5284]. Only one 



example seems to survive [ref_arm_4424]73. Probably in Italy a visor of a pointed shape with 



vision slits was developed. It was usually pivoting at each side of the skull. The central 



pivoting visor with vision slits – said to be of German origin – could also have an extensive 



snout, as the effigy [ ref_ill_art_5258] suggests. The less pointed shape can be found very 



often at northern alpine contemporary effigies, e. g. [ ref_ill_art_5271]. Due to the shape of 



their visor such helmets were called “houndskull -basinet”. The visors were all detachable; 



probably to make this helmet a bit more comfortable when there was no threat to life or 



physical condition. While the versions with the centrally fastened face -guard seem to have 



gone out of fashion in the early 15 th century, the models with the side-pivoting visors were 



in use until the 1440ies. A disadvantage of this helmet was probably that the visor could not 



be locked. A strike from an attacker into an upward direction could easily expose the wearer’s 



face.
S. 62 · Sprachlich überarbeitet · Entwurf

3.3.5 Type V

In the first half of the fourteenth century, pointed Type I helmets developed into Type V through the addition of a flaring nape-guard. Two early examples with short nape-guards survive [ref_arm_2157] PDF [ref_arm_1985] PDF, probably made before 1350. If their visor pivot holes and surviving visor-arm remains are original, they may be the earliest surviving helmets once fitted with pivoting face-guards. The similar [ref_arm_1620] PDF may also have had a nape-guard subsequently cut away. The exceptional helmet [ref_arm_4260] PDF has a brim around its circumference and shares features with Burgundian Type III forms.

A new Type V form developed in the second half of the fourteenth century. In most respects it was a stylistic variation on contemporary Type IV helmets; the significant constructional change was a slight outward flare at the nape below an inward taper. Many surviving examples originally carried a face-guard, invariably attached at the forehead by a single detachable hinge. Some had hemispherical skulls, such as [ref_arm_2023] PDF, whose original visor is lost; others had tapered points [ref_arm_2082] PDF. By the end of the century, similar skulls were probably made both with and without visors and ring-armour collars [ref_arm_1981] PDF74 [ref_arm_1993] PDF.

Shallower, lighter Type V forms appeared in the first half of the fifteenth century. A painting by Masaccio, around 1430, may show early examples [ref_ill_art_5248] PDF: they resemble Type I skullcaps but already have small nape-guards. Probably contemporary surviving examples include [ref_arm_1922] PDF [ref_arm_1994] PDF [ref_arm_2070] PDF [ref_arm_4338] PDF [ref_arm_4414] PDF. The slightly flaring front brim makes [ref_arm_2176] PDF an exceptional variant.

Helmet [ref_arm_1994] PDF closely resembles that worn by the soldier at the lower left of [ref_ill_art_5242] PDF. The surviving object is Type V, while the painted example appears to be Type I, but both have embossed ear areas. Other models have pivoting nasal guards [ref_arm_2079] PDF [ref_arm_2085] PDF [ref_arm_2131] PDF [ref_arm_4513] PDF, also seen in contemporary images [ref_ill_art_5165] PDF [ref_ill_art_5243] PDF [ref_ill_art_5212] PDF [ref_ill_art_5208] PDF.

Originalwortlaut vergleichen
3.3.5 Type-V 



In the first half of the 14 th century the type -I helmets with a pointed skull developed into 



helmets of type-V by the addition of a flaring nape-guard. Two early examples with a short 



nape-guard do survive [ ref_arm_2157] [ref_arm_1985]. They were probably made before 



1350. If the visor pivot holes respectively the remains of a visor arm at these helmets are of 



the p roduction time then these helmets might be the oldest surviving examples once 



equipped with a pivoting face -guard. Due to the similarity to these helmets the item 



[ref_arm_1620] might also have had a nape-guard that was cut off at later times. The helmet 



[ref_arm_4260] with its circumferential brim is absolutely unique. It shows features of a 



“Burgundian” helmet of type-III. 



In the second half of the 14th century a new type-V helmet was developed. For the most part 



it was only a stylistic variation of the contemporary type -IV helmets. Technologically 



absolutely new was the skull to slightly flare out at the nape below a slight tapering. Many 



extant examples had a face-guard attached. This was invariably fastened at the forehead by 



a single, detachable hinge. Some variations had a half -bowl shaped skull [ ref_arm_2023] 



(the genuine visor is missing), others a tapered point [ref_arm_2082]. Probably by the end 



of the 14 th century helmets of the same shape were made with and without a ring -armour 



collar and a visor attached [ref_arm_1981]74 [ref_arm_1993]. 



In the first half of the 15 th century also a less deep, lighter variation of type -V helmets was 



produced. Early examples might be depicted on a painting by Masaccio from about 1430 



[ref_ill_art_5248]. They still look like simple skull caps of type-I, but small nape-guards are 



already visible. Extant examples of probably the same period are [ ref_arm_1922] 



[ref_arm_1994] [ref_arm_2070] [ref_arm_4338] [ref_arm_4414]. Due to its brim slightly 



flaring out at the front the helmet [ref_arm_2176] is an absolutely unique variation of type-



V . The helmet [ ref_arm_1994] is very similar to the one worn by the soldier on the lower 



left side of [ref_ill_art_5242]. The extant example is of type-V , while the one in the painting 



seems to be of type -I, but both helmets have the embossing at the ears in common. Some 



models have a pivoting nasal guard [ ref_arm_2079] [ ref_arm_2085] [ ref_arm_2131] 



[ref_arm_4513] that can also be found at contemporary depictions [ ref_ill_art_5165] 



[ref_ill_art_5243] [ref_ill_art_5212] [ref_ill_art_5208].
S. 62–63 · Sprachlich überarbeitet · Entwurf

3.3.6 Type VI

In 1926, Oswald Graf Trapp published a study of the development of the Type VI group commonly called armets.75 These were intended exclusively for mounted combat. Although generally regarded as Italian, their earliest depiction is German [ref_ill_art_5336] PDF and unusually shows a pointed skull. Their relationship to earlier types is uncertain.

The previously overlooked [ref_arm_2158] PDF, possibly made in the early fifteenth century, may be the oldest surviving Type VI example. It remains unrestored in the MDA stores, heavily corroded and lacking its cheek-plates and presumed face-guard. Its rear tail and hinges are nevertheless characteristic of fifteenth-century Type VI helmets. The distinctive [ref_arm_1929] PDF is otherwise known only from artworks of the 1440s.

The form now called an armet probably developed in the 1420s. By at least the 1440s, it frequently had a pointed visor pivoting at the sides [ref_arm_1932] PDF. For the first time, vision was provided by the slit between the visor’s upper edge and the lower edge of the forehead. These models had a riveted forehead reinforcement and an attached ring-armour collar, none of which survives. Most also had a disc riveted to a short horizontal stem at the lower nape [ref_arm_1938] PDF, although these discs are generally lost. Their function remains unresolved despite repeated discussion.

Armet variants continued to be made until around 1520. Their principal advantage was close-fitting protection for the whole head, including the chin and upper neck, while the pointed visor encouraged weapons to glance aside.

Originalwortlaut vergleichen
3.3.6 Type-VI 



Oswald Graf Trapp in 1926 published an article on the development of one group of type -



VI helmets, the so called “armets”. 75 This helmet is exclusively made for fighting on 



horseback. Although this is considered to be an Italian helmet -model, the earliest depiction 



is found in Germany [ref_ill_art_5336] – uncommonly with a pointed skull. It is not clear if 



it developed from a preceding type. An as yet unattended helmet possibly made in the early 



15th century might be the oldest extant example of a type -VI helmet [ ref_arm_2158]. It is 



kept un-restored in the storage of the MDA. The cheek-plates and the presumable face-guard 



are missing and it is heavily corroded. Nevertheless, the “tail” at the rear and the hinges are 



typical for 15 th century type -VI helmets. Anoth er unique example is [ ref_arm_1929] – 



otherwise only known from artworks of the 1440ies.  



The helmet that is now called “armet” probably developed in the 1420ies. At least from the 



1440ies it is frequently equipped with a side -pivoting, pointed face-guard [ref_arm_1932]. 



The sight for the first time was provided by a slit between the upper edge of the visor and



the lower edge of the forehead. All these models had a reinforce-plate riveted to the forehead 



and a ring-armour collar (none is extant) attached to the lower edge. Most of them had a disc 



riveted to a short horizontal shank at the lower edge of the nape [ref_arm_1938], but at extant 



item these discs usually got lost. Their purpose has often been discussed, without any final 



explanation. This type of helmet in different variations was produced until about 1520. It 



had the great advantage of fitting very closely, protecting all the head, including the chin and 



the upper parts of the neck. The pointed visor made attacking weapons slide off.
S. 63 · Sprachlich überarbeitet · Entwurf

3.3.7 Type VII

Type VII, used chiefly in the second half of the fifteenth century, contains the largest number of subgroups. Two open-faced forms were current in Italy. Both have applied forehead reinforcements, but one has a nape-guard made in one piece with the skull [ref_arm_2090] PDF [ref_arm_2117] PDF, while the other uses one or more articulated lames [ref_arm_1777] PDF. The surviving [ref_arm_1830] PDF resembles the helmet in [ref_ill_art_5247] PDF. A richly decorated form, rare among surviving objects, appears in Botticelli’s painting of the early 1480s [ref_ill_art_5375] PDF (description 1); compare [ref_arm_1765] PDF [ref_arm_1855] PDF [ref_arm_1751] PDF.

Another Italian model has a sharply pointed nape-guard and a side-pivoted visor incorporating the forehead reinforcement [ref_arm_1672] PDF [ref_arm_1807] PDF. Alternatively, the reinforcement is riveted directly to the skull, while a visor covering only the area below the eyes turns on low pivots [ref_arm_1688] PDF [ref_arm_1706] PDF [ref_arm_2094] PDF. These forms were intended for foot soldiers and were not fitted to costly Italian suits.

In Germany, Type VII probably developed from Type III helmets with low brims and vision slits. Many forms in the second half of the fifteenth century had fixed face protection with a vision slit; this arrangement continued in the tournament form known as Rennen into the second half of the sixteenth century. From the 1470s, German Type VII helmets also had pivoting visors, with [ref_arm_1704] PDF or without [ref_arm_1733] PDF integrated forehead reinforcements. Their nape-guards were generally longer and could consist of articulated plates [ref_arm_1727] PDF or a single fixed plate [ref_arm_1837] PDF.

The so-called black sallet is rare among surviving Type VII helmets [ref_arm_1702] PDF [ref_arm_4254] PDF [ref_arm_1886] PDF and still rarer in images [ref_ill_art_5306] PDF (description 1) [ref_ill_art_5337] PDF [ref_ill_art_5334] PDF [ref_ill_art_5383] PDF (description 1). It appears to have been confined to southern Germany in the late fifteenth and early sixteenth centuries. These helmets were never polished, have many pairs of small holes, and generally lack turned edges.

Type VII left the chin and neck exposed, so separate neck protection was often added. Towards the end of the fifteenth century, armourers experimented with mounting it on the visor pivots [ref_arm_1904] PDF [ref_arm_1971] PDF [ref_arm_1810] PDF. These arrangements developed into the closed helmet, used into the seventeenth century. Contemporary images show that Type VII helmets with pivoting visors and long nape-guards were, with few exceptions, worn with mounted armour.

Originalwortlaut vergleichen
3.3.7 Type-VII 



The type-VII helmet is the one to be divided into the most sub -groups. It is a type that was 



mainly used in the second half of the 15th century. Basically two open-face versions were in 



fashion in Italy: Both have an attached forehead reinforce, but one has the nape-guard made 



in one piece with the skull [ ref_arm_2090] [ref_arm_2117], the other one has it made from 



one or more articulated lames [ref_arm_1777]. Similar to the helmet shown on the painting 



[ref_ill_art_5247] is the extant example [ref_arm_1830]. A special, richly decorated version 



– rare in extant examples – is painted by Botticelli in the early 1480ies [ ref_ill_art_5375] 



(descr. 1) [ref_arm_1765] [ref_arm_1855] [ref_arm_1751].  



Another Italian model had a sharply pointed nape -guard and a side -pivoting visor with an 



integrated forehead-reinforce [ref_arm_1672] [ref_arm_1807]. Alternatively the forehead -



reinforce could be riveted directly to the skull and the visor – now protecting only below the 



eyes – had only low pivots [ref_arm_1688] [ref_arm_1706] [ref_arm_2094]. These helmets 



were meant only for foot-soldier’s use, in Italy they were never added to costly armour suits. 



In Germany the development of the type-VII helmet is probably based on a helmet of type-



III that had a low brim with vision-slits. In the second half of the 15th century many type-VII 



helmets had a fixed face -guard with a slit for the vision. This variation remai ned in use for 



the tournament -variation “Rennen” until the second half of the 16 th century. From the 



1470ies also in Germany type -VII helmets got a pivoting visor, with [ ref_arm_1704] or 



without [ref_arm_1733] an integrated forehead-reinforce. Usually the German helmets had 



a longer nape-guard that could be made of one or more articulated plates [ref_arm_1727] or 



one single fixed plate [ref_arm_1837]. 



The so called “black sallet” forms a rare group of extant helmets of type-VII [ref_arm_1702] 



[ref_arm_4254] [ref_arm_1886]. Even rarer are illuminations [ ref_ill_art_5306] (descr. 1) 



[ref_ill_art_5337] [ref_ill_art_5334] [ref_ill_art_5383] (descr.1). It seems like this helmet 



was exclusively used in southern Germany in the late 15th and early 16th century. Typical for 



these helmets is that they were never polished, the show many pairs of small holes and the 



edge is usually not turned. 



Type-VII helmets did not protect the chin and the neck. Therefore, the armourers often added 



a separate neck-protection. By the end of the 15th century the armourer’s experimented with 



the attachment of the neck -protection to the visor pivots [ ref_arm_1904] [ref_arm_1971] 



[ref_arm_1810]. These helmets later developed into the so called “closed helmet ”, a type 



used until the 17 th century. According to contemporary depictions type-VII helmets with a 



pivoting visor and a long nape -guard were used with only few exceptions in combination 



with a horseman’s suit of armour.
S. 63–64 · Sprachlich überarbeitet · Entwurf

3.3.8 Type VIII

Type VIII brings together several distinct forms, all of which had to be fastened to torso protection and therefore depended on other armour components. Since from at least 1450 they were used exclusively in tournaments rather than battle, further subdivision is left to future research.

The first group, commonly called “Stechhelm”, developed from Type II. Images indicate occasional battlefield use until around 1450 [ref_ill_art_5148] PDF [ref_ill_art_5358] PDF. It was usually assembled from three riveted plates: a very thick, narrowly curved front plate protecting the face, a low crown and a rear plate. The face protection was never articulated [ref_arm_1644] PDF.

The great basinet was likewise not confined to tournaments [ref_ill_art_5173] PDF. Its skull and rear were made in one piece, with one or two plates beneath the chin protecting the throat and a pivoting visor. Visors could be hemispherical [ref_arm_1633] PDF [ref_arm_1635] PDF [ref_arm_1652] PDF or frog-mouthed [ref_arm_1650] PDF [ref_arm_1627] PDF.

A particular variant consists of at least four plates, with a separate skull and lower rear section. These examples appear to be Type IV helmets converted to Type VIII during the first half of the fifteenth century by replacing the ring-armour collar with plates of comparable extent. Holes for the former collar attachments remain visible inside the skull’s lower edge [ref_arm_1768] PDF [ref_arm_1655] PDF [ref_arm_1653] PDF.

A special great-basinet variant with a bowl-shaped skull continued into the early sixteenth century for the tournament use described in the original as “foot-combat tournaments (Kolbenturnier)”. Its visor was either an iron-bar grille screwed to the skull [ref_arm_1646] PDF or a pivoting, perforated hemispherical plate [ref_arm_1647] PDF.

Redaktionelle Hinweise · 1
  • Die Gleichsetzung „foot-combat tournaments (Kolbenturnier)“ ist fachlich auffällig. Originalaussage sichtbar erhalten und zur Klärung markiert.
Originalwortlaut vergleichen
3.3.8 Type-VIII 



The helmets defined as type-VIII are actually of several different types. All helmets needed 



to be fastened to the torso -protection and therefore they could only be used in combination 



with other body -armour parts. As all type -VIII helmets at least from 1450 on are used



exclusively in different tournament -types and never in battle, a further differentiation was 



spared for future studies. 



The first group, the so called “Stechhelm” developed from type-II helmets. Until about 1450 



– according to depictions in contemporary art – it could occasionally also be used in battle 



[ref_ill_art_5148] [ref_ill_art_5358]. The skull was usually riveted together fro m three 



plates: A very thick frontal plate in the shape of a lean bow for the protection of the face; a 



low skull; and a plate at the rear of the head. The face -guard was never articulated 



[ref_arm_1644]. 



Also the great basinet was not exclusively used in tournament [ ref_ill_art_5173]. This 



helmet had the skull and the rear plate worked in one piece with the skull, one or two plates 



below t he chin to protect the throat and a pivoting visor. The latter was shaped either 



hemispherical [ ref_arm_1633] [ ref_arm_1635] [ ref_arm_1652] or frog -mouthed 



[ref_arm_1650] [ref_arm_1627]. A special variation consists of at least 4 plates, as the skull 



and the low er rear regions are made from separate plates. It has not been noted that all of 



these examples are actually type-IV helmets that – in the first half of the 15th century – were 



turned into type -VIII by basically replacing the ring -armour collar by plates o f the same 



dimensions. At the lower edge of the skull -plate at all examples interiorly the holes for the 



pulleys that once held the ring-armour collar are still visible [ref_arm_1768] [ref_arm_1655] 



[ref_arm_1653]. 



A special version of the great bascinet with a bowl shaped skull remained in use for foot -



combat tournaments (Kolbenturnier) until the early 16 th century. The visor was screwed to 



the skull and forged from iron bars to form a grill  [ref_arm_1646] or it was pivoting and 



made of a perforated hemispherical plate [ref_arm_1647].
S. 64 · Sprachlich überarbeitet · Entwurf

3.3.9 A noteworthy form with no surviving pre-1500 example

No example made before 1500 appears to survive of the helmet commonly called “burgonet” or “Sturmhaube”, although it recurs in images from the early fourteenth century [ref_ill_art_5250] PDF throughout the fifteenth [ref_ill_art_5242] PDF. Its principal features are a projecting fall above the eyes and a flaring nape-guard. It became popular in the early sixteenth century and survives in large numbers.

The only examples with substantially earlier components are Type IV [ref_arm_1562] PDF or Type VII helmets [ref_arm_1793] PDF [ref_arm_5130] PDF fitted with falls during the fifteenth, sixteenth or seventeenth century.

Originalwortlaut vergleichen
3.3.9 A noteworthy, not preserved type 



No example from before 1500 seems to survive of the so called “burgonet” or “Sturmhaube”, 



despite depictions from the early 14 th century on (e. g. [ ref_ill_art_5250]) throughout the 



15th century (e. g. [ref_ill_art_5242]) repeatedly show such a helmet. Its main characteristic 



is the “fall” above the eyes and the flaring napeguard. By the beginning of the 16 th century 



it becomes a popular type and is extant in many examples. The only basically older examples 



are type-IV [ref_arm_1562] or type-VII helmets [ref_arm_1793] [ref_arm_5130] to which a 



“fall” was attached in the 15th, 16th or 17th century.
S. 64 · Sprachlich überarbeitet · Entwurf

3.4 Leg protection

Protecting the leg is almost as demanding as protecting the arm: complete leg armour must still allow the wearer to walk and kneel. The earliest plate-like defences were probably leather, sometimes reinforced with iron or bone strips. None survives. Nor, to the author’s knowledge, do ring-armour or segmented hose or stockings, although they appear in artworks.

Originalwortlaut vergleichen
3.4 Leg-protection 



The sufficient protection for the leg is similarly complicated to the protection of the arm. 



The wearer must not be restrained in walking – and kneeling! – when wearing full leg 



armour.  



The oldest plate-like protections were probably made of leather, occasionally reinforced with 



iron or bone bars. No leather armour -part for the leg survived. As far as the author knows 



also no ring-or segmented-armour hose or stockings are extant, despite them being depicted 



in artworks.
S. 64–65 · Sprachlich überarbeitet · Entwurf

3.4.1 Knee

After helmets, knee defences were the first armour objects made from a single large plate, appearing from around 1250.76 The knight on [ref_ill_art_5254] PDF wears Type I knee protection. Few examples survive [ref_arm_2280] PDF [ref_arm_2281] PDF [ref_arm_2282] PDF [ref_arm_2283] PDF [ref_arm_2284] PDF [ref_arm_2285] PDF [ref_arm_2286] PDF [ref_arm_4650] PDF.

As at the elbow, armourers extended the plate into a shell-like projection on the outer side to protect the rear of the joint, producing Type II. Transitional forms appear in [ref_ill_art_5291] PDF and on the standing knight in [ref_ill_art_5175] PDF. Their parallel vertical ridges resemble those on surviving Type I examples [ref_arm_2282] PDF [ref_arm_2280] PDF.

Gottfried of Arnsberg’s effigy [ref_ill_art_5256] PDF combines older features, such as reinforced leather forearm protection, with Type II knees whose extensions cover the outer side. The surviving [ref_arm_2266] PDF may be among the earliest examples, perhaps the oldest.77 All surviving Type II knee defences have a medial ridge. Pointed versions appear in artworks [ref_ill_art_5279] PDF, but none is known to survive.

Originalwortlaut vergleichen
3.4.1 Knee 



After the helmet the knee protections from 1250 on are the first armour parts to consist of a 



single large plate. 76 The knight on the effigy [ ref_ill_art_5254] wears knee protections of 



type-I. Only few type -I knee prot ections made of plate do survive [ ref_arm_2280]



[ref_arm_2281] [ ref_arm_2282] [ ref_arm_2283] [ ref_arm_2284] [ ref_arm_2285] 



[ref_arm_2286] [ref_arm_4650].  



In parallel to the elbow -protections the armourer later sought to protect the rear side of the 



knee joint by a shell -like extension at the small toe -side (type-II). Transitional types are 



found at [ref_ill_art_5291] and the standing knight [ref_ill_art_5175]. Their parallel vertical 



ridges are similar to extant  examples of type -I [ref_arm_2282] or [ ref_arm_2280]. While 



Gottfried of Arnsberg at his effigy [ ref_ill_art_5256] is still equipped with some old 



fashioned armour parts, like the reinforced leather lower arms, his knee protections are 



already of type-II, with the shell-like extensions at the small toe side. One very early extant 



example – possibly the oldest type-II knee defense – is probably [ref_arm_2266]77. All extant 



knee protections of type -II have a medial ridge. Pointed knee protections seem to have 



existed according to contemporary artw orks [ ref_ill_art_5279], but no extant example is 



known.
S. 65 · Sprachlich überarbeitet · Entwurf

3.4.2 Lower leg

Images already show large plates protecting the front of the lower leg around 1250.78 Leather remained in use in the second half of the fourteenth century [ref_ill_art_5249] PDF (description 1), sometimes fastened over ring-armour stockings [ref_ill_art_5280] PDF. The lower-leg defences on [ref_ill_art_5254] PDF were probably also leather. No Type I lower-leg plate survives, and Type II examples are rare [ref_arm_2539] PDF [ref_arm_2828] PDF.

Most surviving lower-leg protection is Type III. The earliest examples date from the second half of the fourteenth century [ref_arm_2291] PDF [ref_arm_2325] PDF. Contrary to the repeated claim that such plates were never decorated with ridges, contemporary artworks show embossed decoration [ref_ill_art_5285] PDF [ref_ill_art_5296] PDF [ref_ill_art_5156] PDF, as do some surviving objects [ref_arm_2298] PDF [ref_arm_2335] PDF [ref_arm_2304] PDF.

Together with tapered helmet skulls, Type III lower-leg defences were among the most elaborately shaped large plates of the fifteenth century. They follow the asymmetrical anatomy of the lower leg closely, requiring considerable skill. Their shaping became less elaborate as production expanded during the sixteenth century.

Originalwortlaut vergleichen
3.4.2 Lower leg 



Already about 1250 depictions show larger plates for the protection of the front of the lower 



leg.78 In the second half of the 14th century the armour for the lower leg could still be made 



of leather [ ref_ill_art_5249] (descr. 1), occasionally fastened onto ring -armour stockings 



[ref_ill_art_5280]. Also the lower legs at the brass [ ref_ill_art_5254] were probably made 



of leather. No type-I lower-leg and only very few type -II protections exist [ ref_arm_2539] 



[ref_arm_2828].  



The far larger number of lower leg armour is of type-III. The oldest examples date from the 



second half of the 14 th century [ref_arm_2291] [ref_arm_2325]. Despite the often repeated 



opinion that lower legs were never – also not later – decorated by ridges, contemporary 



artworks do often show embossed decorations [ ref_ill_art_5285] or [ ref_ill_art_5296] 



[ref_ill_art_5156]. Also some extant examples are known [ ref_arm_2298] [ref_arm_2335] 



[ref_arm_2304]. Together with tapered helmet skulls lower leg-protections of type-III were 



the most elaborately worked larger plates in the 15 th century. Without exception they 



resemble very closely the human anatomy. As the lower leg is unsymmetrical it is difficult 



to cover it with a close fitting plate. The lower legs were worked less elaborately in shape 



when from the 16th century on armour was produced in larger quantities.
S. 65 · Sprachlich überarbeitet · Entwurf

3.4.3 Thigh

The oldest surviving Type I thigh defence dates from the mid-fourteenth century [ref_arm_3023] PDF and was probably riveted inside a textile or leather covering. A few early fifteenth-century examples survive [ref_arm_2909] PDF [ref_arm_2922] PDF. Type I continued to be made for lighter equipment [ref_arm_2926] PDF, particularly in Spain, until the end of the fifteenth century [ref_arm_2932] PDF.

Since Type I left the rear of the thigh exposed, Italian armourers added a hinged flap from the early fifteenth century, producing Type II. Leg armour was chiefly intended for mounted use, and the side facing the horse was left without plate coverage. Type II remained in field use until the end of the sixteenth century. Type III thigh protection was made only for tournament armour in the early sixteenth century.

Redaktionelle Hinweise · 1
  • Die Fortdauer von Oberschenkeltyp I bis Ende des 15. Jahrhunderts widerspricht der allgemeineren Begrenzung in §2.2.5.4.1.1. Regionale Ausnahme und Unsicherheitsgrad erhalten; noch nicht harmonisiert.
Originalwortlaut vergleichen
3.4.3 Upper leg 



The oldest extant upper leg defense of type -I dates from the mid-14th century 



[ref_arm_3023]. This was probably still riveted interiorly to fabric or leather. A few items 



from the beginning of the 15th  century do survive [ ref_arm_2909] [ ref_arm_2922]. For 



lighter equipment [ref_arm_2926] and especially in Spain this type was still produced until 



the end of the 15th century [ref_arm_2932].  



The type-I upper legs left the rear side of the leg without defense. Therefore, from the early 



15th century on the Italian armourers attached a flap to the upper leg (type-II). As leg armour 



is merely meant for use on horseback, the side of the leg turned to the horse’s body was not 



covered by plates. This type was in use on field armour until the end of the 16th century. 



Type-III upper legs were only made for tournament armour in the early 16th century.
S. 66 · Sprachlich überarbeitet · Entwurf

3.4.4 Systems

Because the lower leg does not rotate in the same way as the forearm, thigh, knee and lower-leg plates can be linked directly. From the second half of the fourteenth century, the knee was permanently connected to the thigh defence, while the lower-leg element remained detachable. Different combinations of types were used.

Until the mid-fourteenth century, thigh, knee and lower-leg systems covered only the front of the leg [ref_ill_sys_leg_luI_lkI_llI]. From then until the early fifteenth century, the usual combination was Type I thigh, Type II knee and Type III lower leg [ref_ill_sys_leg_luI_lkII_llIII]. The combination of Type II thigh and knee with Type III lower leg then became the most widespread system, used across Europe from the early fifteenth to the end of the sixteenth century [ref_ill_sys_leg_luII_lkII_llIII].

During the second half of the fifteenth century, an alternative system used Type II elements throughout [ref_ill_sys_leg_luII_lkII_llII]. In the same period, lightly equipped foot soldiers wore Type I thigh and Type II knee protection without Type III lower-leg defences [ref_ill_art_5309] PDF (description 2).79 Knee plates could also be worn independently of both thigh and lower-leg protection [ref_ill_art_5199] PDF.

Originalwortlaut vergleichen
3.4.4 Systems 



As the lower leg cannot twist like the lower arm it is possible to protect the upper leg, the 



knee and the lower leg by directly joined plates. From the second half of the 14th century on 



the knee was permanently connected to the upper leg, but the lower leg defense was always 



detachable. Systems consisting of a combination of different types were produced.  



Until the mid-14th century armour systems for the knee, the upper and the lower leg was only 



covering the front side of the leg [ ref_ill_sys_leg_luI_lkI_llI]. From then on until  the early 



15th century the leg was covered by an upper leg defense of type -I, by a knee defense of 



type-II and a lower leg defense of type-III [ref_ill_sys_leg_luI_lkII_llIII]. From then on the 



system – type-III lower leg, type-II knee and type-II upper leg – was the most common and 



was made from the early 15 th century until the end of the 16 th century in all Europe 



[ref_ill_sys_leg_luII_lkII_llIII ]. In the second half of the 15th century in parallel to this also 



a system with all parts of made of type-II existed [ref_ill_sys_leg_luII_lkII_llII]. In the same 



period light defenses for foot soldiers of type -I upper legs and type -II knees were worn 



without lower legs of type-III [ref_ill_art_5309]79 (descr. 2). Knee protections could also be 



used singly, without being attached to an upper or lower leg-protection [ref_ill_art_5199].
S. 66 · Sprachlich überarbeitet · Entwurf

3.4.5 Foot

Foot protection appears never to have covered the sole. Images still show relatively old-fashioned scale-covered feet in the 1430s [ref_ill_art_5239] PDF [ref_ill_art_5342] PDF, although larger lames were already known before 1350 [ref_ill_art_5286] PDF. These developed into articulated systems covering the top of the foot up to the lower-leg defence, Type II.

In Italy, ring armour with a small toe plate, Type I, continued alongside them well into the second half of the fifteenth century. The Earl of Warwick’s effigy [ref_ill_art_5232] PDF shows Type III foot protection, with articulated plates covering the heel as well as the rest of the foot.

Originalwortlaut vergleichen
3.4.5 Leg foot 



It seems as if all foot -protections never covered the sole. As late as the 1430ies depictions 



show the somewhat old fashioned scale protected feet [ ref_ill_art_5239] or 



[ref_ill_art_5342]. But already before 1350 foot protections made of larger lames were 



known [ ref_ill_art_5286]. These developed i nto a system of joined articulated plates, 



protecting the upper side of the foot until the lower leg defense (type-II). In Italy in parallel 



the foot until the second half of the 15 th century was often protected merely by ring-armour 



and a small plate at the toes (type-I). At the Earl of Warwick’s effigy [ref_ill_art_5232] foot 



protections of type-III can be seen that cover all the foot including the heels with articulated 



plates.
S. 66–67 · Sprachlich überarbeitet · Entwurf

3.5 Neck protection

Until the first half of the fifteenth century, the gap between helmet and torso protection was covered inadequately by ring armour alone. The development of plate neck protection remains uncertain. An inventory of 1436 already records:

[…] item 27 stukh pertt [German, pl. Bärte] und vizier […]
Inventory of 1436; note 80. 80

The German “Bart”, literally “beard”, now denotes protection for the chin and throat. An early depiction north of the Alps is [ref_ill_art_5153] PDF (description 2), and [ref_arm_3097] PDF may be among the earliest surviving examples. All surviving Type I neck defences date from 1480–1500 [ref_arm_3173] PDF [ref_arm_3197] PDF. Compared with Type II, their principal advantage was the absence of the vulnerable joint between upper and lower elements, which could be forced open by a blow.

Images frequently show protection confined to the lower neck. Surprisingly, only two examples predating 1500 survive [ref_arm_3072] PDF [ref_arm_3152] PDF. Some depictions indicate that plates covered the throat and nape while leaving the chin free, Type III, by the second quarter of the fifteenth century. On [ref_ill_art_5219] PDF (description 1), a hinge on the wearer’s right joins front and rear plates. Type III could also be worn with Italian armour [ref_ill_art_5335] PDF (description 2); only one example of this form survives [ref_arm_3092] PDF.

The lower plate of a neck defence could be worn either outside or beneath the breastplate [ref_ill_art_5218] PDF (description 1). These objects were generally combined with Type III [ref_arm_3133] PDF [ref_arm_3165] PDF, Type VI [ref_arm_3081] PDF or Type VII helmets. Variants of Types II and III continued to be made until the end of the sixteenth century.

Redaktionelle Hinweise · 1
  • Die unterschiedlichen Aussagen zur Zahl erhaltener früher Halsplatten (zwei bzw. eine eines bestimmten Typs) sind erhalten; genauer Bezugsumfang bei der Autorendurchsicht prüfen.
Originalwortlaut vergleichen
3.5 Neck-protection 



Until the first half of the 15 th century the gap between the helmet and the torso -protection 



was insufficiently protected by ring -armour only. The development of the plate neck -



protection is still obscure. Already by 1436 an inventory itemizes:  



[…] item 27 stukh pertt [German, pl. Bärte] und vizier […]80  



The German word for the neck-protection is “Bart”, meaning the same like “beard”. Today 



this term describes a protection for the chin and the throat. A very early depiction of such a 



defense north of the Alps is found in [ref_ill_art_5153] (descr. 2). Probably one of the oldest 



extant examples is [ref_arm_3097]. Extant type-I neck-protection all date from 1480 to 1500 



only [ref_arm_3173] [ref_arm_3197]. Their main advantage over type-II was that the weak 



seam of the upper and the lower part was less likely to open when hit by any kind of weapon. 



In contemporary depictions often also a defense which covers only the lower part of the neck 



can be seen. It is surprising to see that only two examples from before the year 1500 are 



extant [ref_arm_3072] [ref_arm_3152]. On some illustrations it becomes clear that already 



by the second quarter of the 15 th century the throat and the nape could be covered by plates 



while the chin is left unprotected (type -III). This is indicated for example at the effigy



[ref_ill_art_5219] (descr. 1), where on the right side of the deceased’s ne ck-protection a 



hinge is visible, connecting the rear and the front plates. Also on Italian armour a neck -



protection of type -III could be worn [ ref_ill_art_5335] (descr. 2). Of this type o f neck 



defense only one example still exists [ref_arm_3092] 



Neck-protections could be worn with their lower plate optionally upon or underneath the 



breastplate [ ref_ill_art_5218] (descr. 1). They were usually meant to be combined with 



helmets of type-III [ref_arm_3133] [ref_arm_3165], -VI [ref_arm_3081] and -VII. Different 



versions of type-II and –III neck-protections were made until the end of the 16th century.
S. 67 · Sprachlich überarbeitet · Entwurf

3.6 Torso protection

Claude Blair cites a document of 1171 that may refer to torso protection made from small plate segments, the earliest written evidence for plate armour he located.81 Tracing torso construction is difficult because plates were generally concealed beneath a surcoat until the late fourteenth century.

A stained-glass window of around 1370 suggests one arrangement: two armoured men wear vertical lames, probably riveted over an underlying garment [ref_ill_art_5159] PDF. Several segmented torso defences survive. Before 1400, their fronts were permanently connected to their backs [ref_arm_3924] PDF [ref_arm_3923] PDF; [ref_arm_3886] PDF [ref_arm_3885] PDF. Textile garments lined with small plates continued into the mid-sixteenth century; such an armoured jacket is usually called a brigandine.

Originalwortlaut vergleichen
3.6 Torso-protection 



Claude Blair quotes a written document of 1171 that might tell of torso-protections 



consisting of smaller plate segments.81 This is also the earliest document of plate armour he 



could find. The tracking of the development of torso-protections is difficult, as until the late 



14th century the plates were usually covered by a surcoat. What such an arrangement could 



have looked like can be seen on a stained glass window of about 1370: Two armoured man 



wear torso -protections with vertical lames – probably riveted upon an undergarment 



[ref_ill_art_5159]. Several segmented torso-protections still exist. Before the year 1400 they 



consisted of a front -protection that was permanently connected to a back -protection 



[ref_arm_3924] [ref_arm_3923]; [ref_arm_3886] [ref_arm_3885]. Torso protections being 



a combination of textiles and small, interiorly placed plate segments were used until the mid-



16th century. Such an armoured jacket is usually called “brigandine”.
S. 67–68 · Sprachlich überarbeitet · Entwurf

3.6.1 Front of the torso

The earliest surviving breastplates are Type I [ref_arm_3734] PDF [ref_arm_3814] PDF [ref_arm_3963] PDF [ref_arm_4018] PDF [ref_arm_4071] PDF [ref_arm_4077] PDF, all probably dating to around 1400. The first one-piece example cannot be located or dated precisely, but was most likely made in the second half of the fourteenth century. Early examples had textile coverings, preserving a connection with segmented construction. The covering may also have joined front and rear plates directly [ref_ill_art_5289] PDF (description 1).

An unflared lower edge could be driven into the wearer’s abdomen by a blow. Around 1410, some Type I plates therefore had their lower edges turned outwards to present a less sharp surface [ref_arm_3810] PDF. Such plates, and examples with decorative applied strips, were no longer covered externally by fabric and may have lacked directly attached pelvis protection. The vertical segments of [ref_arm_3811] PDF, however, remained connected internally by leather, still recalling the earlier covered construction.

Two breastplates once covered with fabric retain pelvis lames in their original positions [ref_arm_3698] PDF [ref_arm_3507] PDF. These lie outside the breastplate’s lower edge. This joint was vulnerable: a weapon sliding towards the waist could enter between the upper plate and the lames. The uppermost pelvis lame was made concave to improve its fit [ref_arm_3698] PDF.

In early fifteenth-century Italy, once all the plates were external, the upper edge of this lame was extended over part of the breastplate, producing Type IV [ref_arm_3607] PDF. Type I then ceased to be made. The extended lame, better termed an abdominal plate, gradually rose farther over the chest plate [ref_arm_3797] PDF. By around 1490, Italian examples could cover almost the entire upper plate, leaving only its turned edges visible [ref_arm_3609] PDF. Surviving objects suggest that German armourers did not begin making Type IV breastplates before the 1470s. In both regions, weight could be reduced by cutting away the lower chest plate so that the overlap was limited to a narrow joint. Type IV remained in production until the mid-sixteenth century.

Probably alongside this Italian development, German-speaking armourers developed a comparatively neglected construction. To close the vulnerable waist joint, they placed the uppermost pelvis lame inside the lower edge of a Type I chest plate, producing Type III. This abdominal element could itself consist of several lames [ref_ill_art_5372] PDF (description 3) [ref_ill_art_5341] PDF (description 1) [ref_ill_art_5216] PDF [ref_ill_art_5230] PDF [ref_ill_art_5193] PDF [ref_arm_3440] PDF [ref_arm_4024] PDF.

The earliest surviving chest plate probably once fitted with a narrow internal abdominal element may be [ref_arm_3428] PDF. It is the only surviving example of the box-shaped Type III form frequently depicted in northern European art from around 1420 to 1450.82 Images confirm that the so-called Kastenbrust was often Type III [ref_ill_art_5241] PDF. Less pronounced box forms survive from the 1440s [ref_arm_3621] PDF and 1450s [ref_arm_3438] PDF [ref_arm_3623] PDF [ref_arm_4043] PDF.

Many carried broad skirts of pelvis lames. A sword could pass through an opening in the skirt [ref_ill_art_5223] PDF (description 3), recalling twelfth-century practice with openings in ring-armour shirts [ref_ill_art_5310] PDF. Images also show scale skirts on Kastenbrust forms [ref_ill_art_5268] PDF (description 1).

A late medieval fencing book shows Type III breastplates whose chest elements appear divided centrally, hinged to the backplate at the sides and buckled together at the front [ref_ill_art_5226] PDF. No example survives, but similar constructions appear in several artworks [ref_ill_art_5193] PDF [ref_ill_art_5341] PDF (description 2). A related example in [ref_ill_art_5209] PDF may have a central strip covering such a division, although this is uncertain. Type III breastplates appear to have been used chiefly north of the Alps until the mid-sixteenth century.

The simplest breastplate form may be the latest to develop. Type II appears in images only from around 1480 [ref_ill_art_5354] PDF (description 2), and the earliest surviving examples generally date from that period [ref_arm_3458] PDF [ref_arm_3447] PDF. A single plate above the pelvis was easier to make because separate chest and abdominal elements did not need to be fitted together. It also reduced weight by eliminating overlaps and presented no stepped joint in which a weapon could catch. Type II continued to be made for cavalry until the nineteenth century, giving it the longest production history of any armour component.

Originalwortlaut vergleichen
3.6.1 Torso front  



The oldest extant breastplates are of type-I [ref_arm_3734] [ref_arm_3814] [ref_arm_3963] 



[ref_arm_4018] [ ref_arm_4071] [ ref_arm_4077], they all date around the year 1400 



probably. It is not clear when and where the first single piece example was made, but it was 



most likely in the second half of the 14 th century. The earliest of them had been covered by 



fabric, which emphasizes their relation to former segment-armour protections. Via the cover-



material the back-plates were possibly directly attached to the front-plate [ref_ill_art_5289] 



(descr. 1). As the lower edge was not angled, a blow would probably drive the edge into the 



wearer’s abdomen. At some plates of type-I therefore about 1410 the lower edge was turned 



exteriorly to reveal a les s sharp radius [ ref_arm_3810]. Such plates, as well as plates with 



decorative plate straps, were not covered exteriorly by fabric anymore and possibly had no 



directly attached pelvis protection. Nevertheles s, the different vertical segments of the 



breastplate [ref_arm_3811] – still similar to the segmented -armour system with an exterior 



cover – are connected interiorly via a leather -lining. Two breastplates – once exteriorly 



covered by fabric – still retain one or more pelvis -lames in their original position 



[ref_arm_3698] [ref_arm_3507]. In both cases they are placed exteriorly at the lower edge 



of the breastplate. This region was a weak point. Attacking weapons would easily slide to 



the direction of the waist and penetrate in between the pelvis-lames and the upper breastplate. 



To improve their fitting, the armo urer gave the most upper pelvis -lame a concave section 



[ref_arm_3698]. In the early 15th century – when the plates were already all placed exteriorly 



– the Italian armourers extended the upper edge of the f irst pelvis-lame to double parts of 



the upper breastplate (type-IV) [ref_arm_3607]. The type-I breastplate was from then on not 



produced anymore. Within the next years to come, on Italian armour the upper e dge of the 



doubling lower pelvis -lame – now it should be rather called “abdomen -plate” – extended 



permanently further up the thorax-plate [ref_arm_3797], until about 1490 in Italy it covered 



all the upper b reastplate with the exception of the turned edges of the thorax -plate below



[ref_arm_3609]. According to extant examples it seems as if the German armourers did not 



start to make breastplates of type -IV before the 1470ies. In Italy and Germany the total 



weight of type -IV breastplates was often reduced by cutting the lower edge of the thorax -



plate so the abdomen -plate would only overlap at a narrow seam -region. Type -IV 



breastplates were produced until the mid-16th century. 



Probably in parallel to the development of type -IV breastplates in Italy, in the German 



speaking lands an as yet insufficiently attended breastplate-type was developed. Presumably 



also with the intention of protection improvement at the gap between the waist and the upper 



breastplate the armourers placed the most upper pelvis -lame interiorly at the lower edge of 



the type-I thorax-plate (type-III). This lame – now also better called “abdomen-plate” could 



also consist of several lames [ ref_ill_art_5372] (descr. 3) [ ref_ill_art_5341] (descr. 1) 



[ref_ill_art_5216] [ ref_ill_art_5230] [ref_ill_art_5193] [ ref_arm_3440] [ref_arm_4024]. 



The oldest extant plate that once probably had such a narrow abdomen -plate attached 



interiorly is possibly [ ref_arm_3428]. It is the only s urviving model of a box shaped type -



III breastplate found in large numbers in northern European artworks from about 1420 to 



1450.82 That the so called “Kastenbrust” was often of type -III is documented on many 



contemporary artworks [ ref_ill_art_5241]. Several examples with only moderately box -



shaped silhouettes dating from the 1440ies [ ref_arm_3621] to the 1450ies do exist 



[ref_arm_3438] [ref_arm_3623] [ref_arm_4043]. Many examples have several pelvis-lames 



attached, forming a wide skirt of plates. The sword is often stuck through a hole in the pelvis-



lames [ref_ill_art_5223] (descr. 3) – a feature that is known similarly already in the 12 th 



century [ref_ill_art_5310], where the sword was stuck through a hole in the ring -armour 



shirt. According to depictions the skirt of the “Kastenbrust” could also be made of scales 



[ref_ill_art_5268] (descr. 1).  



In a late medieval fencing book the fighters wear breastplates of type-III [ref_ill_art_5226]. 



The thorax-plate seems to be split in two, hinged to the backplate at the sides and fastened 



in the center by buckles. Even though no extant plate of this system is known, it is similarly 



depicted at several different artworks, e. g. [ ref_ill_art_5193] or [ ref_ill_art_5341] (descr. 



2). A related breastplate – here it is unclear if the central plate strap covers the gap of the 



centrally split plate – is shown on [ref_ill_art_5209]. Type-III breastplates seem to have been 



used merely in northern alpine Europe until the mid-16th century.  



A very simple type of breastplate is probably the you ngest development. Only from about 



1480 on breastplates of type -II appear in contemporary artworks [ref_ill_art_5354] (descr. 



2) and the earliest extant exam ples do usually date from about 1480 on [ ref_arm_3458] 



[ref_arm_3447]. They have major advantages in comparison  to all other types: As the part 



above the pelvis consists of one plate only, they are easy to make. T he thorax and the 



abdomen-plate do not have to get adjusted  to each other ; they are l ight as they have no 



overlaps. There are no steps from overlapping plates on the surfa ce, no weapon would get 



stuck there. This type of breastplate was made for Cavalry until the 19 th century and is 



therefore the armour part with the longest tradition.
S. 68–69 · Sprachlich überarbeitet · Entwurf

3.6.1.1 Front of the hips

By the 1430s, armourers in Italy and the German-speaking lands were attaching individual plates beneath the breastplate’s pelvis lames, one over each thigh, to cover the gap above the thigh defence. Early square forms appear on the Ghent Altarpiece [ref_ill_art_5262] PDF. A stained-glass window in Bern Minster, dated 1447, already shows the shield-like outline retained over the next forty years [ref_ill_art_5153] PDF (description 1).

From the late 1480s, these single plates were replaced by several horizontal lames extending the pelvis protection over each thigh. Early examples may be [ref_ill_art_5368] PDF and [ref_arm_3652] PDF.83 During the sixteenth century they lengthened, reaching the knee around 1550. Between 1550 and 1630, the addition of Type II knee defences allowed them to replace separate thigh and knee protection entirely.

Originalwortlaut vergleichen
3.6.1.1 Front of hip 



Already in the 1430ies the armourers in Italy and in the German Speaking lan ds attached 



single plates at the lower edge of the breastplate pelvis-lames – one for each upper leg. They 



were meant to protect the gaps between the upper leg defense and the breastplate. Early 



square examples are depicted at the Gent altarpiece [ref_ill_art_5262] and at a stained glass 



window in the Münster of Bern of 1447. Here they have already the shape of coat -of-arms,



a shape they will keep for the next 40 years [ ref_ill_art_5153] (descr. 1). From the late 



1480ies on the one -piece “torso upper leg -protections” were split into several horizontal 



lames, being extensions of the pelvis -lames for the protection of each upper leg. Early 



examples might be [ref_ill_art_5368] and [ref_arm_3652]83. In the 16th century they reached 



further down the upper leg until about 1550 they reached the knee. When between 1550 and 



1630 a knee-defense of type-II was joined to the torso -upper leg-protections, they entirely 



replaced the separate knee and upper leg defense.
S. 69–70 · Sprachlich überarbeitet · Entwurf

3.6.2 Back of the torso

Back protection is rarely shown in contemporary art. The earliest rear view located for this study is the statue of St Maurice in Magdeburg Cathedral [ref_ill_art_5374] PDF (description 2). Dating is difficult because close comparisons are lacking. It is usually assigned to the second half of the thirteenth century, but a date in the first half of the fourteenth is also possible, in view of Italian depictions of segmented back protection from the second quarter of that century.

In [ref_ill_art_5185] PDF, the back protection is painted violet and rivet heads are visible, suggesting small plates held together beneath a textile covering, perhaps like [ref_arm_3909] PDF. Two extensions beneath the arm openings buckle together across the centre with horizontal leather straps. Each also buckles upwards towards the neck opening of an underlying central element, which may have consisted of one or several plates.

At first sight, the horizontal lines and rivet rows on St Maurice suggest plates fixed outside leather or fabric. The lines may instead indicate a belt or lame permanently attached around the waist. Surviving objects show that horizontal rivet rows can secure vertically arranged internal lames. The statue’s back protection may therefore resemble examples from Wisby [ref_arm_3891] PDF.

The development of plate back protection is particularly difficult to reconstruct because so few early examples survive. The statue of St George in Prague [ref_ill_art_5290] PDF (description 1) gives a detailed rendering of small segments beneath fabric or leather. An hourglass-shaped central upper plate can be discerned. One surviving plate has precisely this form [ref_arm_3384] PDF, and another is similar but larger [ref_arm_4800] PDF.

Back protection appears to have developed more slowly than breastplates. Until the end of the fourteenth century, it probably continued to use small segments riveted inside a covering. One form combined a central trapezoidal plate with smaller elements over the lower sides. Few of the latter have been identified; some may survive unrecognised in collections. Central plates are more numerous [ref_arm_3379] PDF [ref_arm_3380] PDF [ref_arm_3382] PDF [ref_arm_3383] PDF [ref_arm_3385] PDF [ref_arm_4767] PDF [ref_arm_4773] PDF [ref_arm_4780] PDF [ref_arm_4789] PDF [ref_arm_4792] PDF [ref_arm_4796] PDF.

Type IV backplates appeared in Italy around 1400, alongside Type IV breastplates. The earliest example, around 1410, is preserved at Churburg. Although chiefly Italian, the construction also occurs in later examples decorated in northern Alpine styles. The plain [ref_arm_3374] PDF and [ref_arm_3406] PDF were made in Innsbruck around 1490. The closely related [ref_arm_3327] PDF and [ref_arm_3387] PDF were probably made in German-speaking lands, whereas marks on [ref_arm_3404] PDF [ref_arm_3410] PDF [ref_arm_3412] PDF indicate northern Italy.

Type III probably developed in German-speaking regions: it is absent from Italian artworks and Italian suits. The earliest surviving examples may be [ref_arm_3303] PDF and [ref_arm_3269] PDF, followed perhaps in the 1460s by [ref_arm_3315] PDF. The latter’s broad ridges beside the arm openings recall earlier northern forms. Images show centrally divided backs, resembling segmented constructions, apparently hinged to the breastplate [ref_ill_art_5172] PDF [ref_ill_art_5275] PDF.

Later backplates often have a separate plate riveted around the neck opening [ref_arm_3345] PDF. This may recall either the earlier central trapezoidal element or the way an undergarment remained visible at German backs of the 1450s [ref_ill_art_5275] PDF. Italian armourers also made Type III for northern markets, but the sole surviving example [ref_arm_3296] PDF suggests that this was uncommon. A painting demonstrates continued production into the early sixteenth century [ref_ill_art_5151] PDF.

Fifteenth-century Type II backplates are rare, the earliest dating from the final two decades of the century. Front and rear Type II protection probably developed at roughly the same time. Early Italian examples are plain [ref_arm_3365] PDF, while German-speaking examples carry modest ridge decoration [ref_arm_3311] PDF [ref_arm_3368] PDF. Type II backplates continued to be made for cavalry until the nineteenth century.

Type I backs, unlike the preceding types, did not develop alongside the corresponding breastplates. They first appear in the 1490s [ref_arm_3417] PDF. A connection with older segmented backs remains possible: all surviving examples combine a central trapezoidal plate with a smaller plate on either side. Contemporary Type III [ref_arm_3334] PDF and Type IV backs [ref_arm_3390] PDF [ref_arm_3374] PDF can use the same upper construction. Even the upper element of the early Type IV back [ref_arm_3391] PDF consists of a central plate with permanently attached side extensions.

Originalwortlaut vergleichen
3.6.2 Torso back 



Backplates are rarely illustrated in contemporary artworks. The earliest depiction the author 



could find of an armoured man shown from his back is the statue of St. Mauritius in the 



Dome of Magdeburg [ ref_ill_art_5374] (descr. 2). T his statue is very difficult to date, as 



comparable objects are not at hand. Usually it is said to date from the second half of the 13th 



century. Anyway, it is also possible that it was made in the first half of the 14 th century, as 



other depictions of segmented back-protections in artworks of Italian make from the second 



quarter of the 14 th century suggest. In the painting [ ref_ill_art_5185] the back parts are 



shown colored in violet and a s rivet heads are visible it is likely that the back armour 



consisted of small plate segments covered and held together by fabric, probably similar to 



the extant example [ref_arm_3909]. Two “wings” are visible under the arm cutouts, fastened 



centrally by two horizontally buckled leather straps. Each is also buckled upwards towards 



the nape cutout of a central plate underneath. The latter may have consisted of one or several 



single plates. The backplates at the statue of St. Mauritius on the first look seem been riveted 



exteriorly on leather or fabric, as the visible horizontal lines and the horizontal rows of rivets 



suggest. The horizontal lines do rather remark a belt or a plate -lame that was permanently 



fixed to the armour and that surrounded the entire waist. Extant examples do suggest that the 



horizontal rows of rivets can actually interiorly hold vertically arranged lames. Similar to 



the backplates found in Wisby the plates of St. Mauritius could have bee n arranged 



[ref_arm_3891].  



It is particularly difficult to reconstruct the genesis of plate armour protections for the back 



as only very few early examples do survive. The most precise rendition of an earl y back-



protection, still consisting of very small segmented plates inside a fabric or leather material 



is found at the statue of St. George from Prague [ ref_ill_art_5290] (descr. 1). In the upper 



central area the silhouettes of hour -glass shaped plate is visible. One plate of exactly the 



same shape [ ref_arm_3384] and a similar, but larger plate [ ref_arm_4800] are extant. 



However, it seems like the development of a plate-protection for the back had fallen behind 



the development of breastplates. Until the end of the 14th century backplates were most likely 



still made of smaller plate segments riveted inside a fabric cover. One special type seems to 



have consisted of one trapeze-shaped central plate together with some smaller segments that 



covered the sides of the lower back. The latter segments are not preserved in large numbers, 



some separate items might still exist in collections but have not yet be identified as parts of 



a back-protection. On the other hand the larger central plates are extant in several examples 



[ref_arm_3379] [ ref_arm_3380] [ ref_arm_3382] [ ref_arm_3383] [ ref_arm_3385] 



[ref_arm_4767] [ ref_arm_4773] [ ref_arm_4780] [ ref_arm_4789] [ ref_arm_4792] 



[ref_arm_4796].



In parallel to the breastplates of type -IV from 1400 on in Italy backplates of type -IV were 



made. The oldest example of about 1410 i s preserved in the armoury at the Castle of 



Churburg. While this remained merely an Italian backplate -construction, also few later 



examples decorated in the northern alpine taste are preserved. The backplates 



[ref_arm_3374] and [ref_arm_3406] are plane examples made in Innsbruck about 1490. The 



closely related backplates [ ref_arm_3327] and [ref_arm_3387] were probably made in the 



German speaking lands, but the items [ref_arm_3404] [ref_arm_3410] and [ref_arm_3412] 



according to the types of their marks were made in northern Italy.  



The backplate of type-III was probably developed in the German speaking lands – it is found 



neither in Italian artworks nor at Italian suits of armour. The oldest examples to survive are 



probably [ref_arm_3303] and [ ref_arm_3269]. Only slightly later, maybe dating from the 



1460ies is [ ref_arm_3315]. At this example, the wide ridges in parallel to the arm -cutouts 



remind on the design of older northern alpine backplates. At these – similar to the segmented 



types seen on artworks – the plate was still split vertically in the center [ ref_ill_art_5172] 



and obviously hinged to the breastplate [ ref_ill_art_5275]. Later backplates often have a 



separate plate riveted at the nape cutout [ ref_arm_3345]. This feature might remind either 



on the central trapeze-shaped plate of older backplates or on the way the undergarment was 



visible at German backplates of the 145 0ies [ ref_ill_art_5275]. For the northern alpine 



market also the Italian armourers produced back -protections of type -III, but as 



[ref_arm_3296] is the only extant example such variations were probably less common. 



Backplates of type-III were obviously still produced by the early 16th century, as the example 



at the painting [ref_ill_art_5151] shows. 



15th century backplates of type-II are very rare; the earliest examples date from the last two 



decades of the 15th century. It is very likely that both, front and back-protections of type-II, 



were developed more or less about the same time. The earliest extant Italian examples are 



plane [ref_arm_3365]. In the German speaking lands they were decorated only moderately 



by few ridges [ref_arm_3311] [ref_arm_3368]. Until the 19 th century backplates of type-II 



were made for the cavalry. 



On the contrary to all aforesaid backplat es, those of type-I were not made in parallel to the 



corresponding breastplate type. Type -I backplates appear for the first time in the 1490ies 



[ref_arm_3417]. Nevertheless, some connection to older segmented backplates might exist, 



as all extant type-I examples are made of a central, trapeze-shaped plate with a smaller plate 



attached at each side. There are also some contemporary backplates of type -III 



[ref_arm_3334] and –IV [ ref_arm_3390] [ ref_arm_3374] where the upper plates are 



constructed in exactly the same manner. Actually the upper plate of the very early backplate 



of type-IV also consists of one c entral plate with two permanently fixed prolongations at 



each side [ref_arm_3391].
S. 70 · Sprachlich überarbeitet · Entwurf

3.6.3 Front and back considered together

Originalwortlaut vergleichen
3.6.3 Concerning torso front and back together
S. 70 · Sprachlich überarbeitet · Entwurf

3.6.3.1 Sides of the hips

Small plates could be fitted at the sides of the hips on both Italian [ref_ill_art_5182] PDF and German armour [ref_ill_art_5228] PDF. Surviving pelvis lames rarely make the original attachment of missing hip plates clear. Images indicate two straps, one riveted to the front pelvis lames and one to the rear [ref_ill_art_5182] PDF. Few hip plates survive; their style suggests Italian manufacture [ref_arm_3872] PDF [ref_arm_3925] PDF [ref_arm_3926] PDF [ref_arm_5136] PDF [ref_arm_3871] PDF.

Originalwortlaut vergleichen
3.6.3.1 Side of hip 



To Italian [ref_ill_art_5182], but also to German armour [ref_ill_art_5228] small plates can 



be attached to the side of the hips.  At the sides of the pelvis -lames at extant armour it is 



usually not visible how the lost hip  protections once were attached . Artworks help to 



understand that they were attached with two straps, one riveted to the pelvis -lames of the 



breastplate and one riveted to the pelvis-lames of the backplate [ref_ill_art_5182]. Not many 



examples are extant and by style they are probably all of Italian make [ ref_arm_3872] 



[ref_arm_3925] [ref_arm_3926] [ref_arm_5136] [ref_arm_3871].
S. 71 · Sprachlich überarbeitet · Entwurf

3.6.4 Systems

A breastplate could be worn without a backplate, but not the reverse. Where both were used, several combinations were possible. The Italian Type IV arrangement is probably the earliest complete torso system [ref_ill_sys_tor_ita_tfIV_tbIV]. Front and back are usually hinged beneath the left arm [ref_ill_art_5231] PDF (description 2) and buckled on the right [ref_ill_art_5233] PDF (description 2). The chest elements are separate from the abdominal elements, creating a horizontal division. Other systems divide vertically into independent front and rear defences.

From the mid-fifteenth century, Type III fronts and backs were worn together north of the Alps [ref_ill_sys_tor_ger_tfIII_tbIII]. From the 1470s, Type III backs were also combined there with Type IV breastplates [ref_ill_sys_tor_ger_tfIV_tbIII], the most common arrangement in German-speaking lands until around 1490. Paired Type II fronts and backs probably appeared in the 1480s and continued into the nineteenth century [ref_ill_sys_tor_ger_tfII_tbII]. In terms of protective coverage, none of these systems is superior to the others.

Redaktionelle Hinweise · 1
  • Die absolute Aussage, ein Rückenschutz könne nicht allein getragen werden, ist eine Aussage dieses Quellenabschnitts und keine allgemeine Regel des Datenmodells. Die Zugehörigkeit einzelner erhaltener Objekte wird daraus nicht abgeleitet.
Originalwortlaut vergleichen
3.6.4 Systems 



A breastplate could be worn without a backplate , but not vice versa . Breast and backplates 



were worn together in different combinations. The Italian type -IV system is probably the 



oldest full torso-protection [ref_ill_sys_tor_ita_tfIV_tbIV]. Here the front- and the backplate 



are usually hinged together under the left arm [ref_ill_art_5231] (descr. 2) and closed by 



buckles at the right side [ref_ill_art_5233] (descr. 2). The thorax-plates are separate from the 



abdomen-plates – a horizontal split. All other systems are split vertically in an independent 



front- and backplate. From the mid-15th century on in northern alpine Europe front and back-



protections of type -III were worn together [ ref_ill_sys_tor_ger_tfIII_tbIII]. Exclusively in 



these regions from the 1470ies on backplates of type-III were combined with breastplates of 



type-IV [ref_ill_sys_tor_ger_tfIV_tbIII] – until about 1490 the most common system in the 



German speaking lands. Probably from the 1480ies on – until the 19th century – type-II torso-



protections were combined [ ref_ill_sys_tor_ger_tfII_tbII]. Judging by protective aspects 



none of the system is superior to the other.

4 Technological features

S. 72–74 · Sprachlich überarbeitet · Entwurf

4 Technological features: an overview

Armourers left no written accounts explaining their working methods or the intended functions of particular constructional features. Today, their products are valued more for their beauty and individuality than for the sophisticated technology involved in making them centuries ago. Yet surviving objects still reveal much about the engineering skills of their makers. Their visible details must be studied and interpreted if we are to answer the many questions that remain. In 1921, Bashford Dean, founder of the Department of Arms and Armor at the Metropolitan Museum of Art in New York, wrote:

For, truth to tell, no one can really know armour who has not studied it with microscopic care, examining its spring-latches, linings, straps, hinges, rivets, plume holder, and […] its buckles.
Bashford Dean (1921), p. 60.

The technological features Dean listed have never been adequately examined and described, although they offer a wide range of criteria for comparison.84 This study aims to establish a sound basis for comparisons that may help distinguish original armour from later reproductions. To do so, it is necessary to classify the features found on surviving plate armour.

Why did nineteenth- and twentieth-century collectors and scholars not compare and publish the largest possible number of objects to substantiate their findings? Many of the objects known today were already known to them. One principal constraint explains why their comparisons generally remained limited: the cost of assembling the necessary information in one place. Ideally, researchers would examine all the relevant objects together. Since this was—and remains—impracticable for various reasons, bringing together records of those objects is indispensable.

Researchers had to travel, photograph objects, develop their photographs, and obtain books and documents. Publication required manuscripts to be typed, pages to be laid out by hand, and books to be printed. The more objects an author compared, the greater the research costs; the more images included to substantiate statements about those objects, the greater the printing costs. These expenses led to various compromises. Print runs were small. Many nineteenth- and early twentieth-century publications contained no images, substituting lengthy descriptions for illustrations. Others used drawings or a limited number of black-and-white photographs. Even today, colour printing is often avoided because of its cost.85

Digital technologies have reduced these obstacles to scholarly communication.86 Digital photography removes the need to develop film, while the internet provides access to countless free resources, including museum images, illustrated discussions in forums, bibliographies and texts. Above all, it offers a virtually unlimited publishing platform at very low cost. The cost of printing images no longer constrains the author. Comprehensive discussion based on a broad body of related evidence has therefore become much more achievable.

Had earlier scholars had these tools, they would surely have used them extensively. Direct access to images could have reduced the need for lengthy descriptions, while removing the constraints of small print runs and expensive books would have brought their findings to a much wider readership. A digital device cannot yet reproduce the tactile experience of a book. Print-on-demand technology nevertheless offers another way of presenting digitally assembled knowledge in a familiar format, while reducing the author’s publication costs.

A publicly accessible digital database, administered by humanities researchers, could bring together many different aspects of armour. Researchers from every relevant discipline could use its records and contribute new findings. Provenance research, for example, is often difficult: many objects have passed through several private collections, leaving gaps in their documented histories. Recording this information centrally would make it easier to consult and help prevent further losses. The standardised terminology proposed above would reduce misunderstandings and facilitate international cooperation. Classifying technical features would also provide extensive comparative evidence. Reconstructing manufacturing processes would support further scientific investigation of historical technologies and questions of authenticity.87

For this study, I developed a digital database capable of serving as such a central information resource. At present, it functions as a research tool for the questions addressed here and does not yet contain all the desired information. Its structure nevertheless allows all traceable object data to be recorded and compared. For almost all of the approximately 5,000 objects included, it contains at least basic collection information and one image. Many records also contain further technological and other details.

Earlier studies commonly excluded doubtful objects from their discussion. This obscured a significant and problematic aspect of the history of arms and armour. Doubtful pieces can be assessed objectively only when both originals and reproductions are considered. The database therefore includes many reproduced objects.

The foundation of this study is the description and classification of details that permit comparisons between surviving objects. The lack of written sources makes this approach necessary. Turned edges, rivets, joints and embossed ridges are among the features that provide comparative evidence. During the research, many details on different objects proved so similar that they could be covered by a common description. Some occur so frequently that they can almost be regarded as standard forms. These recurring forms can often support well-founded proposals for the original appearance of damaged objects or objects with missing constructional elements.

The objects themselves provide the evidence for every classification and reconstruction proposed here. The aim is to develop an expandable catalogue of observations that can help answer a range of technological questions. It is not possible to cite every object displaying each feature discussed below; the references are therefore limited to a few illustrative examples.

Redaktionelle Hinweise · 2
  • Zeitgebundene Aussagen über Forschung, digitale Möglichkeiten und Datenbankbestand beziehen sich auf die Dissertation, nicht auf einen neu erhobenen Stand von 2026.
  • Die absolute Aussage zum Fehlen schriftlicher Werkstattberichte wurde als Aussage des Originals erhalten. Keine neue Quellenprüfung.
Originalwortlaut vergleichen
4 Summarizing technological features 



The armourers did not leave any written document on how they were working and what they 



intended to achieve with the construction of certain p roduct-features. Today, such products 



are valued rather for their beauty and uniqueness than for the sophisticated technology that 



created them so many centuries ago. This is an unfortunate truth, as in the extant examples 



themselves there is still a lot t o be read about the “engineers” the armourers of old were. It 



is the visible details that have to be studied and interpreted to find answers on many open 



questions on the topic. Already in 1921 Bashford Dean, the founder of the arms and armour 



department at the metropolitan Museum of Art in New York, wrote: 



For , truth to tell, no one can really know armour who has not studied it 



with microscopic care, examining its spring-latches, linings, straps, 



hinges, rivets, plume holder , and […] its buckles.84 



The tech nological features named by Dean had never been examined and described 



satisfactorily, despite them providing a vast field of comparable factors. It is the aim of this 



study to establish a stable basis for comparisons that could possibly help to tell the g enuine 



armour apart from the reproduced. Therefore, it is necessary to classify all the features found 



on extant plate armour. 



Why did not already 19 th and 20 th century collectors and scholars simply compare and 



publish the largest possible number of objects for substantiating the findings of their studies? 



A good part of the objects known now was also known then!  



The answer is simple: When reconsidering why comparisons remained limited to a small 



choice of extant examples only, the reasons can be reduced to one main factor: the cost of 



centrally assembling all the necessary data for comprehensive comparisons. Of course, it 



would be best for scholars to have all concerned artifacts – the objects themselves – on the 



table. As this; for various reasons; is no t possible, a central assembling of data was – and 



still is – indispensable. For this purpose, journeys had to be made, items had to be 



photographed and to be developed; literature or documents had to be obtained. If the findings 



were meant to be published , manuscripts had to be typed, text layouts had to be made 



manually and books had to be printed. All this meant: The more items an author intended to 



compare the higher the research -costs would become; the more images were about to be 



included in a publication – inescapable for substantiating statements made in text on artifacts 



– the higher the printing costs would become. The necessary consideration of these cost -



factors resulted in different compromises: editions were limited to few copies only; in the 



19th and early 20th century many publications contained no images; instead of illustrations, 



long and detailed descriptions were inserted; some publications made use of drawings, while 



others of course were already illustrated by a limited number of black -and-white 



photographs. Until today the print of colored images is often avoided – due to the higher 



costs.85  



The digital age by various technological innovations 86 makes it now possible to reduce the 



impact of the aforesaid factors on scientific knowledge-transfer. Digital photography makes 



the film -development dispensable. The internet provides for a countless number of free 



sources – be it images from museum databases, discussions and images in forums or access



to bibliographies and texts. The most important feature that the internet provides is the very 



low cost unlimited platform for scholarly publications of any kind. The printing cost of 



images becomes irrelevant for the author. Therefore, the goal of discussing topics on the 



basis of all -embracing, related data had become much closer at hand. If the 19 th and 20 th 



century scholars would have had such tools at hand, they would certainly have made 



extensive use of it. Description would have been reduced, due to the simple visual access to 



the artifacts. The scientific findings would have spread much wider, as the barrier of limited 



prints and high book-prices would be largely reduced. Of course, the haptics of a book cannot 



yet equivalently be replaced by a digital device. The printing of books on demand wit h the 



help of modern technology offers a further possibility that makes digital knowledge 



accessible the way people are used to – but with reduced cost for the scholarly author 



himself.  



A digital and publicly accessible database could provide for an overv iew of many different 



aspects of armour, a project that should be administrated by scientists of the humanities. All 



kinds of approaches and disciplines occupied with historical armour could make use of the 



collected data – and in return could feedback potential new recognition to the database. For 



example the reconstruction of all provenance -stations is usually a difficult endeavor. Most 



of the objects went through different private collections and their provenance documentation 



is often interrupted. A cen tral registration of provenance data would make this important 



information easily accessible and would help to avoid further losses. The acceptance of a 



standardized terminology as suggested above would help to avoid misunderstandings and 



would make international cooperation much easier. The classification of different technical 



features of armour would deliver a large amount of data for analogies. The reconstruction of 



the techniques necessary for the making of armour would provide a basis for further 



approaches of natural sciences to the reconstruction of the historical technologies and the 



authenticity question87. 



The author of this paper has developed a digital database -system that could fulfill the 



requirements of a central information -platform. For the moment it serves only as technical 



equipment for the research questions of this study and does not contain all desired object -



data yet. Nevertheless, the structure of this database provides the possibility to collect and 



subsequently compare all traceable object-data. On nearly all of the ca. 5000 objects in the 



database the author noted at least the basic collection da ta and at least one image of  each 



item is included. For many objects further data on technological and other details has already 



been added to the data-sheet.  



Preceding studies focusing on armour usually ignored the doubtful pieces found within the 



sum of considered objects. This is not acceptable as this way an important and problematic 



aspect of the history of arms and armour got widely concealed. Only after both, originals 



and fakes, are overviewed, objective conclusions on doubtful objects can be drawn. 



Therefore, many reproduced items were included in the database. 



The main column on which this study will be standing is the description and classification 



of any kind of detail to be found on extant armour, which could serve for comparisons to 



other objects. The lack of written sources makes such an approach necessary. Th ere are 



actually a number of features on late medieval armour that provide information for analogies: 



turned edges, rivets, joints, ridge-embossing etc. In the course of this study it became clear 



that many of these technological features found on different extant items were so similar to 



each other that they could be summarized by one description. Some features are so common 



that they can almost be considered as “standards”. In many cases these “standards” allow



well-founded suggestions on how damaged or i ncomplete armour appeared in its original 



condition. The source for all classifications and suggestions is the real object. The aim is to 



develop an extendible catalogue that comprises facts for answers on different technological 



questions. It is not possible to quote all items showing one of the specific features discussed 



below. Therefore, only few examples are quoted as illustrative references.
S. 74–75 · Sprachlich überarbeitet · Entwurf

4.1.1 Forming the plates

Several depictions of armourers at work survive from the fourteenth to the sixteenth century [ref_ill_art_5373] PDF [ref_ill_art_5329] PDF [ref_ill_art_5214] PDF [ref_ill_art_5301] PDF (description 1) [ref_ill_art_5356] PDF [ref_ill_art_5323] PDF [ref_ill_art_5325] PDF. Only one shows almost the full range of tools and equipment in detail [ref_ill_art_5330] PDF (description 1). Identifying the tools is only part of reconstructing the craft. Tools of similar form and function remain in use in other trades; the techniques by which armourers produced particular shapes are much harder to establish. The following account briefly considers how protection for different body regions may have been made.

Forming a helmet from a single plate requires the greatest investment of time and effort. Transforming a rigid, flat sheet into a deep bowl demands considerable skill. These difficulties probably explain why several helmet types were assembled from riveted segments, both before and after 1350. Protection for other body regions could also require elaborate shaping. Two basic methods can produce the same form, making it impossible to determine with certainty which was used for a particular surviving object.

In the first method, the plate is worked from the inside of the intended bowl. Closely spaced blows from a round-headed hammer drive it into a hemispherical mould or hollow stake, while the workpiece is continually rotated. Depending on its thickness, the plate need not be heated. The following forms may have been made by this process—dishing—in cold metal, although thicker plates may have required hot working:

The second method resembles the making of a silver cup [ref_ill_art_5311] PDF, using a technique still practised by goldsmiths and silversmiths. The plate may first be dished into a shallow bowl. Its inner surface is then placed against a stake, and the outside is hammered, beginning at the widest diameter and rotating the plate as work proceeds. The hammer strikes just below the point of contact with the stake, leaving a small inward indentation with each blow. Repeated working gathers the metal towards the rim and may make it slightly thicker. In the process described here, this gathering requires hot forging. The following forms are identified as requiring this method—raising:

  • Helmet skulls made from a single plate.
  • Pointed visors for Type IV [ref_arm_1567] PDF and Type VI helmets.
  • Pointed, tapered Type II elbow defences [ref_arm_718] PDF.
  • Elbow reinforcements [ref_arm_357] PDF.
  • The tapering portions of Type III, V and VII helmet skulls.
  • The narrowed wrist portions of Type I hand protection.
  • The tapering portions of Type I neck protection.
  • The taper around the knuckles on some Type III hand defences [ref_arm_1063] PDF.
  • Knee defences.
  • Lower-leg defences.
  • The taper of some pointed toe plates [ref_arm_2698] PDF.

Other elements could be cut from a larger sheet and bent into a simple channel, requiring very little additional shaping:

  • Thigh defences.
  • Upper-arm defences.
  • The uppermost lame or lames of Type II neck protection.
  • At least the lower plates of Type II helmets.
  • The lower plates of two-piece Type V helmets [ref_arm_2146] PDF.
  • Separate nape guards attached to Type VII helmets.
  • The lower plates of some Type VIII helmets [ref_arm_1651] PDF.
  • The finger lames of certain hand defences [ref_arm_1127] PDF.
  • The metacarpal plates of certain hand defences [ref_arm_1205] PDF.

The following lames were generally bent without further embossing:

  • Pelvic lames.
  • Lames of thigh protection attached to the torso.
  • Hip-protection lames attached to the torso.
  • Lames between the abdominal and chest plates [ref_arm_3586] PDF.
  • Lames joining the elbow to the upper-arm and forearm plates in the Italian system.
  • Lames at the upper and lower edges of shoulder defences.
  • Lames between the knee and the thigh or lower-leg plates.
  • Foot-protection lames.
  • Upper-arm and forearm lames.
  • Lower-leg lames [ref_arm_2329] PDF.
  • Cuff lames of Type II, III and IV hand protection.
Redaktionelle Hinweise · 1
  • Die Werkstattbegriffe „dishing“ und „raising“ benennen die beiden im Original beschriebenen Verfahren. Die Aussagen zur zwingenden Warmbearbeitung und zur ausschließlich möglichen Herstellung bestimmter Formen bleiben Aussagen der Dissertation; für eine technische Neufassung gegebenenfalls prüfen.
Originalwortlaut vergleichen
4.1.1 The general forming of plate armour 



From the 14 th to the 16 th century several depictions of armourers at work do exist 



[ref_ill_art_5373] [ ref_ill_art_5329] [ ref_ill_art_5214] [ ref_ill_art_5301] (descr. 1) 



[ref_ill_art_5356] [ ref_ill_art_5323] [ ref_ill_art_5325]. Only one is really detailed in 



showing nearly completely all the tools and installations an armourer needed 



[ref_ill_art_5330] (descr. 1). It is not only the tools that need to be known when 



reconstructing the armourer’s craft. The tools are actually all still used in similar shape and 



function for different kinds of crafts until today. What is much more difficult to be 



reconstructed is the techniques the armourers applied to reveal the final shapes of the items. 



The following chapter is a short assumption on how certain body -parts might have been 



made. 



The part consuming the most time and energy is the three dimensional shaping of a helmet 



from a single plate. It requires sophisticated skills to deform a stiff, plane sheet -metal into 



the shape of a bowl. Probably due to these difficulties several helmet types – not only before 



1350 – were made of segments riveted together. Not only the head, also other body regions 



were protected by laboriously shaped plates. Basically two methods can result in the same 



shape. Therefore, it cannot be said with certainty i n which process an extant item has been 



produced. 



The first method is merely working the plate from the inside of the bowl. The material is 



driven into a hemispherical shaped mold or stake by neighboring blows from a round-headed 



hammer. The plate needs to be turned permanently. This process – depending on the plate -



thickness – does not necessarily require the heating of the plate. The following armour parts 



might have been made by this process in cold work – thicker material might have had to be 



worked hot: 



- breastplates 



- backplates  



- lower arm defenses 



- simple elbows [ref_arm_21] 



- shoulders 



- shallow visor [ref_arm_1483] [ref_arm_2172] 



- separate forehead reinforces at type -V , [ref_arm_1946] [ ref_arm_4492] -VI 



[ref_arm_1919] and -VII helmets [ref_arm_2090] [ref_arm_1777] [ref_arm_1706] 



- shoulder reinforces 



The second method works similar to the making of a silver cup [ ref_ill_art_5311] – a 



technique that is still used by gold - and silversmiths today. At the beginning, the work can 



be eased by driving the plate into the shape of a shallow bowl by the aforesaid method. Then 



the bowl is placed with the interior side upon a stake and is hammered from the outside. The 



process is started at the widest diameter; the plate is turned while hammered. The hammer 



does not hit the plate exactly where it is in contact with the stake. It hits instead beneath to 



deform the plate by small negative ditches left by each blow of the hammer. With the 



repetition of this process the material towards the edges gets bulged and therefor e maybe



slightly thicker. The bulging will only work when the metal is forged hot. Some shapes can 



be achieved only by this method: 



- all single-piece helmet skulls 



- pointed visors of type-IV [ref_arm_1567] and -VI helmets 



- pointed and tapered type-II elbows [ref_arm_718] 



- elbow reinforces [ref_arm_357] 



- tapering at type-III, V or -VII helmet skulls  



- tapering at the wrists of type-I hand-protections 



- tapering at type-I necks 



- tapering of knuckles at some type-III hand-protections [ref_arm_1063] 



- knee protections 



- lower leg defenses 



- tapering of some pointed toe-plates [ref_arm_2698] 



Several armour segments could be cut from a larger sheet and be bent into a simple groove. 



Only very little embossing-work was necessary for the making of the following parts: 



- upper legs 



- upper arms 



- most upper lame(s) of type-II necks 



- type-II helmets (at least for the lower plates) 



- the lower plates of two-piece type-V helmets [ref_arm_2146] 



- the attached nape-guards at type-VII helmets  



- the lower plates at some type-VIII helmets [ref_arm_1651] 



- the finger-lames of some hand-protection models [ref_arm_1127] 



- the metacarpal-plates of some hand-protection models [ref_arm_1205] 



 



Usually simply bent and not embossed are the lames: 



 



- of the pelvis 



- of the (torso) upper-legs  



- of the torso-hip 



- between the abdomen and the thorax-plate [ref_arm_3586] 



- between the elbow and the upper/lower arm (Italian system) 



- at the upper and the lower edge of the shoulder 



- between the knee and the upper/the lower leg 



- of the foot  



- of lower/upper arms 



- of lower legs [ref_arm_2329] 



- of type-II, -III and -IV hand-protection-cuffs
S. 75–76 · Sprachlich überarbeitet · Entwurf

4.1.2 Turned and angled edges, and applied bars

The treatment of plate edges is an important feature that has received surprisingly little close attention. No classification of turned edges appears in the existing literature, although such a system could be valuable when comparing objects.

Beyond their decorative role, applied bars and turned edges can serve three purposes:

  • Stiffening the plate. The effect of a shaped section can be illustrated by comparing a flat plastic ruler with the tubular body of a ballpoint pen: the latter can resist bending more effectively even when made from thinner material.
  • Preventing sharp plate edges from cutting the wearer during movement or under the force of a blow.
  • Preventing bullets, arrowheads and blows from polearms or other hafted weapons from sliding across the plate into unprotected areas.

Three main forms of edge treatment can be distinguished. The first uses a solid bar riveted at or close to the edge, most commonly on Italian armour. Between about 1350 and 1450, bars were sometimes fitted around the neck and arm openings of segmented torso protection [ref_arm_3861] PDF [ref_arm_3867] PDF and plate torso protection [ref_arm_3810] PDF [ref_arm_3438] PDF [ref_arm_3623] PDF88 [ref_arm_3607] PDF [ref_arm_3621] PDF [ref_arm_3814] PDF. They also occur on shoulder defences [ref_arm_724] PDF, around the face openings of Type V helmets [ref_arm_1978] PDF [ref_arm_2034] PDF [ref_arm_2043] PDF, near the upper edges of thigh defences [ref_arm_2909] PDF [ref_arm_2851] PDF, and on forearm defences [ref_arm_1] PDF [ref_arm_47] PDF. Their purpose was certainly to intercept blows or projectiles that might otherwise slide off the plate towards unprotected areas.

On fifteenth-century Italian armour, such bars sometimes carry inscriptions or floral ornament made with closely spaced dots punched using a pointed chisel—the technique termed “pointillier” here [ref_arm_3878] PDF. Other bars are decorated by filing [ref_arm_90] PDF [ref_arm_3861] PDF.

The other two main forms can be classified together, since the fully turned edge evidently developed from the simple angled edge: in the second group, the plate edge is bent through approximately 90°; in the third, it is turned until the cut edge touches the plate surface. The classification below describes their sections, probable methods of manufacture and chronological occurrence.

Already in the Bronze Age, armourers turned the lower edges of so-called ridge helmets. These helmets consisted of two halves joined along the crest by an overlapping folded seam [ref_ill_art_5303] PDF. By contrast, the edges of segmented armour were neither turned nor angled. Turning an edge was never essential to the function of plate armour: throughout its history, some edges remained untreated, even in exposed positions. The lower edges of certain late fifteenth-century Type VII helmets, for example, are often left unturned [ref_arm_1796] PDF [ref_arm_1859] PDF, although turned edges had long been established on Types V and VII. On surviving objects, horizontal edges are generally more often turned than vertical ones.

Edges are best turned or angled after the main shape of the object has been completed, because subsequent deformation can damage the edge profile. The operation begins by bending the plate inwards or outwards along a defined line. Different techniques then produce the cross-sections used as the basis for this classification. The accompanying videos demonstrate possible methods of manufacture.

Redaktionelle Hinweise · 1
  • Die umfassende Aussage zu unbehandelten Rändern segmentierter Panzerung wurde erhalten; sie ist keine 2026 neu geprüfte Feststellung.
Originalwortlaut vergleichen
4.1.2 Turned or angled edges and riveted bars 



Surprisingly the very important feature of plate-edge conditioning seems to have never been 



closely regarded by scholars of the subject so far. No attempt for a classification of turned 



edges can be found in the literature. For comparisons of different arm our parts, such a 



classification can be of great importance.  



The application of bars or turns to plate edges besides a decorative aspect can follow the 



subsequent intentions: 



- To stabilize the plate: To illustrate the stabilizing effect of a profile, a good example 



is maybe that a plastic ruler can easier be broken than a plastic ball-pen made of even 



thinner material.



- To prevent the wearer from cuts caused by sharp plate edges: Certain movements of 



the body or strong blows of any kind can cause injuries.  



- To prevent bullets, arrowheads as well as blows and strikes from staff -, or hafted 



weapons from sliding off the plate-surface into unprotected body-regions.  



Three main groups of edge-conditioning can be distinguished: 



1. A massive bar is riveted directly at- or close to an edge – in most cases found on Italian 



armour. From about 1350 to 1450 occasionally bars were riveted close to the throat- and arm 



cutouts of segmented - [ref_arm_3861] [ ref_arm_3867] or plate armour torso-protections 



[ref_arm_3810] [ ref_arm_3438] [ ref_arm_3623]88 [ref_arm_3607] [ ref_arm_3621] 



[ref_arm_3814]; to shoulder protections [ ref_arm_724]; around the face -cutouts of type-V 



helmets [ref_arm_1978] [ref_arm_2034] [ref_arm_2043]; near the upper edge of upper legs 



[ref_arm_2909] [ ref_arm_2851] or to lower arms [ ref_arm_1] [ ref_arm_47]. This was 



certainly done to prevent unprotected body -regions from being injured by strikes or shots 



sliding off the plate surface. On Italian armour of the 15th century, occasionally inscriptions 



or floral ornaments decorated the surface of such bars. They were applied by small dots, 



punched next to each other with the help of a pointed chisel (pointillier) [ ref_arm_3878]. 



Other bars were decorated by simple filing [ref_arm_90] [ref_arm_3861].  



The classification of the following two groups can be combined,  as it was certainly the 



simple angling that later developed into the complete turning. 



2. The edge is simply angled to 900 ca. 



3. The edge is turned so it touches the plate-surface. 



In the following, first the different turned or angled edges found at ext ant armour parts will 



be classified and their making as well as their chronological appearance will be described.  



Already in the Bronze Age, the armourers turned the lower edge of so called “ridge helmets”. 



These helmets consisted of two halves that were connected by an overlapping, over-turned 



edge at the comb [ref_ill_art_5303]. In all times, the plate edges of segmented armour were 



neither turned nor angled. It is generally not necessary to turn the edges to make plate armour 



work. Throughout all times while armour was produced, certain edges remained unturned – 



even at exposed spots. For example, the lower edges of late 15 th century type-VII helmet-



variations are often not turned [ ref_arm_1796] [ ref_arm_1859], even though they were 



produced in a time when turned edges were a long established feature of type -V and -VII 



helmets. A general finding is that most of the turned edges on extant armour parts are set 



horizontally, while most of the vertical edges are not turned.  



An edge can best be turned or angled after the armour piece is readily shaped, as too much 



deformation of a turned edge will result in the partly destruction of its profile. The process 



of turning an edge always starts with angling the plate along a certain line outwards or 



inwards. An edge can be turned by different techniques, to reveal different sections that serve 



as the basis for the following classifications. The quoted videos show how such edges might 



have been made.
S. 76–77 · Sprachlich überarbeitet · Entwurf

4.1.2.1 Type a: a simple angled edge

[ref_ill_edg_a] This is the simplest edge treatment: the plate is bent inwards or outwards through approximately 90°. The resulting profile stiffens the plate but leaves the cut edge relatively sharp. It is easily made with a hammer and an angular stake.

In the first half of the fourteenth century, armourers began slightly bending the edges of vision slits, as on [ref_arm_1443] PDF. Earlier helmets had reinforced these slits with a second, overlapping plate [ref_arm_1457] PDF. Outer edges were also occasionally angled, as on the helmet [ref_arm_1422] PDF, forearm defences [ref_arm_1027] PDF [ref_arm_1029] PDF, segmented front torso protection [ref_arm_3860] PDF, and breastplate [ref_arm_3734] PDF. Type a edges are never decorated.

After 1400, this outward-angled form no longer occurs. In the second half of the fifteenth century, the edges of the shell-like extensions on knee [ref_arm_2405] PDF and elbow defences [ref_arm_722] PDF were bent inwards. Sometimes the bend was divided into segments, producing a faceted outline [ref_arm_127] PDF [ref_arm_583] PDF [ref_arm_3296] PDF.

Originalwortlaut vergleichen
4.1.2.1 Type-a [ref_ill_edg_a] 



This is the simplest conditioning of a plate-edge: It is simply angled outwards or inwards to 



about 900. This profile already stiffens the plate, but the edge is still left relatively sharp. It



is very easy to angle an edge this way. The only tools needed are a hammer and an edged 



stake.  



In the first half of the 14th century the armourers started to slightly angle the edges of vision 



slits, as can be seen at the helmet [ ref_arm_1443]. At earlier helmets these slits were 



reinforced by a second, doubling plate [ ref_arm_1457]. But also outer edges were 



occasionally angled, e. g. at the helmet [ ref_arm_1422], the lower arms [ ref_arm_1027] 



[ref_arm_1029], the segmented torso front [ ref_arm_3860] and the breastplate 



[ref_arm_3734]. Ty pe-a edges are never decorated. After 1400, edges are not angled 



outwards anymore this way. In the second half of the 15th century, the edges of the shell-like 



extensions at knees [ ref_arm_2405] or elbows [ ref_arm_722] were angled inwards, 



sometimes in segments [ ref_arm_127] [ref_arm_583] [ref_arm_3296] to reveal a faceted 



appearance.
S. 77 · Sprachlich überarbeitet · Entwurf

4.1.2.2 Type b: a flat folded edge

[ref_ill_edg_b-inw] [ref_ill_edg_b-outw] [ref_vid_edg_b] Folding the plate edge back through a full 180° produces a rounded, blunt margin. The sharp cut edge is no longer exposed to the wearer, although the stiffening effect may be less than that of Type a. Surviving examples are folded either inwards or outwards. Manufacture is straightforward: a Type a edge is simply hammered flat in the appropriate direction. No decorated fifteenth-century examples are known.

The earliest surviving examples are folded outwards, as on the forearm defence [ref_arm_956] PDF and Type I hand protection [ref_arm_1307] PDF. Type b occurs throughout the fifteenth century, and probably later, on various forms of armour from all production regions. Examples include inward folds [ref_arm_12] PDF [ref_arm_4310] PDF and outward folds [ref_arm_888] PDF [ref_arm_272] PDF. Nevertheless, this is a relatively uncommon edge treatment.

Originalwortlaut vergleichen
4.1.2.2 Type-b [ref_ill_edg_b-inw] [ref_ill_edg_b-outw] [ref_vid_edg_b] 



When a type -a edge is turned completely – by 1800 – the edge gets blunt by the revealed 



radius. No edge threatens to cut the wearer anymore. The stiffening effect might be inferior 



to type-a edges. At extant armour parts, type -b ridges are found either turned interiorly or 



exteriorly. Also this type of turn is not difficult to be made. A type -a edge just needs to be 



hammered flat into the right direction. No decorated variation is known from 15 th century 



armour. 



The earliest extant examples showing an edge of type-b have the latter turned outwards, for 



example the lower arms [ref_arm_956] or the type-I hand-protections [ref_arm_1307]. This 



edge appears throughout all the 15th century and probably also later at different armour types 



of all production regions (interiorly [ ref_arm_12] [ ref_arm_4310] and exteriorly 



[ref_arm_888] [ref_arm_272]). Nevertheless, it is a rather rarely applied type.
S. 77 · Sprachlich überarbeitet · Entwurf

4.1.2.3 Type c: an angled edge with a folded margin

[ref_ill_edg_c-inw] [ref_ill_edg_c-outw] [ref_vid_edg_c-inw] [ref_vid_edg_c-outw] Type c combines the advantages of the preceding forms. An angle stiffens the plate, while the outer margin is folded through 180°, either inwards or outwards, to blunt the edge.

The earlier examples are folded outwards. This treatment occurs around 1410 on the probably Italian breastplate [ref_arm_3814] PDF. From about 1470, Type c is commonly found at the neck and arm openings of plain breastplates probably made in German-speaking regions [ref_arm_3501] PDF [ref_arm_3699] PDF. Inward-folded versions occur on German infantry breastplates from the late fifteenth century [ref_arm_3527] PDF and are common in the early sixteenth. These edges are never decorated.

Originalwortlaut vergleichen
4.1.2.3 Type-c [ref_ill_edg_c-inw] [ref_ill_edg_c-outw] [ref_vid_edg_c-



inw] [ref_vid_edg_c-outw] 



Type-c edges combine both advantages of the aforesaid types. The edge is stiffene d by the 



angling of the plate and the edge is blunted, due to the either in- or exterior 1800 –turning of 



the outer edge. The older versions are turned exteriorly: Already about 1410 the edges of the 



– most likely Italian – breastplate [ref_arm_3814] is turned this way. Edges of type -c are 



usually found at the throat - and arm cutouts of simple breastplates, probably made in the 



German speaking lands [ ref_arm_3501] [ref_arm_3699] from 1470 on. From the late 15 th 



century on also interiorly turned variations were applied to German foot-soldier breastplates 



[ref_arm_3527] – a feature common in the early 16 th century. These edges were never 



decorated.
S. 77–78 · Sprachlich überarbeitet · Entwurf

4.1.2.4 Type d: a rounded hollow roll

[ref_ill_edg_d-inw] [ref_ill_edg_d-outw] [ref_vid_edg_d] This is the simplest edge treatment with a hollow cross-section. The margin is rolled inwards or outwards to form a tube-like section. Sometimes it encloses a wire that remains inside the roll, as in the inward-rolled [ref_arm_1754] PDF and outward-rolled [ref_arm_1802] PDF.

Type d strongly resists bending, and its broad radius prevents the cut edge from injuring the wearer. It is more difficult to make than the preceding types. The edge is first bent around an angular stake with a broad radius, then carefully rolled over with light hammer blows.

Outward-rolled Type d edges occur on all kinds of armour, in all production regions, from the last third of the fourteenth century [ref_arm_810] PDF. The form seems to have gone out of fashion after 1500. Early inward-rolled examples include [ref_arm_1461] PDF [ref_arm_1148] PDF [ref_arm_1711] PDF. In the late fifteenth century, armourers began filing rope-like decoration into these rolls [ref_arm_1063] PDF [ref_arm_1128] PDF. From the early sixteenth century, this roping was often embossed [ref_arm_1345] PDF.

Originalwortlaut vergleichen
4.1.2.4 Type-d [ref_ill_edg_d-inw] [ref_ill_edg_d-outw] [ref_vid_edg_d] 



This is the simplest edge-conditioning with a hollow profile-section. The edge is rolled either 



in- or exteriorly to reveal a pipe -like section. Sometimes the  plate is rolled around a wire 



that remained ins ide the edge (turned interiorly  [ref_arm_1754], turned exteriorly 



[ref_arm_1802]). An edge of type-d strongly resists any kind of bending and its wide radius 



makes absolutely sure that no sharp plate edges can harm the wearer. It is more complicated 



to roll an edge this way than to make one of the aforesaid edges. First the edge is angled with 



a wide radius on an edged stake and then carefully rolled in by slight beats from a hammer. 



Exteriorly turned type-d edges are found at all kinds of armour parts in all production regions 



from the last third of the 14th century on [ref_arm_810]. After 1500 this type seems to have 



gone out of fashion. Early examples of interiorly turned type -d edges are  [ref_arm_1461] 



[ref_arm_1148] [ref_arm_1711]. In the late 15th century, the armourers started to file a roped-



decoration into the turned edges [ ref_arm_1063] [ ref_arm_1128]. From the early 16 th 



century on the roping was often embossed [ref_arm_1345].
S. 78 · Sprachlich überarbeitet · Entwurf

4.1.2.5 Type e: a rounded roll on an angled base

[ref_ill_edg_e-inw] [ref_ill_edg_e-outw] [ref_vid_edg_e] Like Type d, Type e has a rounded cross-section rolled inwards or outwards. It differs in having an approximately 90° bend where the rolled cut edge returns to the plate surface. Some examples also enclose a wire [ref_arm_1404] PDF. Its stiffening and blunting effects resemble those of Type d.

This edge is very common on mid-fifteenth-century Type III helmets from German-speaking regions, both rolled outwards [ref_arm_1402] PDF [ref_arm_1400] PDF [ref_arm_1420] PDF and inwards [ref_arm_1346] PDF [ref_arm_1360] PDF. Inward rolls also commonly occur along the lower edges of separate forehead reinforcements for Type VI helmets [ref_arm_1938] PDF [ref_arm_1942] PDF, on shoulder [ref_arm_612] PDF and forearm defences [ref_arm_365] PDF, and around the neck openings of early sixteenth-century infantry breastplates [ref_arm_3551] PDF. Inward-rolled Type e edges are occasionally decorated by embossing [ref_arm_2054] PDF [ref_arm_1384] PDF.

Originalwortlaut vergleichen
4.1.2.5 Type-e [ref_ill_edg_e-inw] [ref_ill_edg_e-outw] [ref_vid_edg_e] 



This edge is also of an in - or exteriorly rolled round profile -section like type -d, but it is 



angled to about 90 0 where the rolled in cut -edge touches the plate again. Also some items 



with edges of type -e occasionally have a wire inserted [ ref_arm_1404]. The stiffening and 



the blunting effect is similar to type -d edges. This type of turned edge is a very common 



feature of type -III helmets, made in the mid-15th century in the German speaking lands 



(exteriorly [ ref_arm_1402] [ ref_arm_1400] [ ref_arm_1420], interiorly [ ref_arm_1346] 



[ref_arm_1360]). Interiorly turned edges of type-e are commonly found at the lower edge of 



forehead reinforces of type -VI helmets [ ref_arm_1938] [ ref_arm_1942], but also at 



shoulders [ref_arm_612], lower arms [ref_arm_365] and early 16th century throat-cutouts of 



foot-soldier breastplates [ ref_arm_3551]. An interiorly turned edge of type -e can 



occasionally be decorated by embossing [ref_arm_2054] [ref_arm_1384].
S. 78 · Sprachlich überarbeitet · Entwurf

4.1.2.6 Type f: a hollow triangular roll

[ref_ill_edg_f] [ref_vid_edg_f] Type f is the most labour-intensive edge treatment and can only be worked hot. Its hollow section is approximately triangular. The outer apex forms a ridge along the edge, while another corner is rounded. The ridge adds stiffness, and the rounded corner protects the wearer from injury. Only outward-turned examples survive.

On armour from German-speaking regions, the section is approximately equilateral. On armour in the Italian style, the side between the apex and the cut edge is generally shorter than the other two sides, which are roughly equal. The proportions remain broadly consistent as the section becomes smaller towards the ends of the treated edge. This taper occurs around the neck and arm openings of front torso protection, the nape and arm openings of back protection, and on thigh protection attached to the torso, shoulder reinforcements and thigh defences. Type f also occurs along the lower edges of some helmets [ref_arm_1394] PDF and the upper visor edges of Type VI helmets [ref_arm_1908] PDF.

On Italian armour, these edges often carry floral “pointillier” ornament or inscriptions [ref_arm_732] PDF [ref_arm_2873] PDF [ref_arm_3880] PDF. Faceted embossing also occurs [ref_arm_1735] PDF [ref_arm_3637] PDF [ref_arm_3688] PDF, sometimes combined with filing [ref_arm_3723] PDF.

On breastplates attributed to workshops in western Europe, including France, Spain and Flanders, the neck opening may form a small central projection [ref_arm_3518] PDF [ref_arm_3570] PDF [ref_arm_3465] PDF. At least one example in the style of the German-speaking regions also survives [ref_arm_3703] PDF.

Originalwortlaut vergleichen
4.1.2.6 Type-f [ref_ill_edg_f] [ref_vid_edg_f] 



This edge is the most laborious of all types. It can only be worked hot. Edges of type -f are 



basically of a hollow, triangle section. The outer point of the triangle defines a ridge along 



the turned edge; the other angle is defined by a blunt radius. The ridge at the turn further 



stiffens the edge and the radius prevents the wearer from injuries. Only exteriorly turned 



versions are found at extant armour parts. In the German speaking lands, the section of the 



triangle is rather equal-sided. On armour of Italian style in section the side between the point 



and the cut plate -edge is usually shorter than the other two sides, which are more or less 



equal in length. While the proportions of the sides stay more or less the same, the dimensions 



of the cross section usually grow more narrow towards the end of the turned edge at throat-



, nape and arm cutouts of torso front - and back-protections, at torso-upper leg-protections, 



shoulder reinforces and upper legs. Some helmets have a type-f edge applied [ref_arm_1394] 



to the lower edge and also the upper visor -edge at helmets of type -VI is sometimes turned 



this way [ref_arm_1908].  



At the type-f edges of Italian armour often floral “pointillier” decorations or inscriptions can 



be found [ ref_arm_732] [ ref_arm_2873] [ ref_arm_3880]. Also faceted embossing 



occasionally occurs [ ref_arm_1735] [ ref_arm_3637] [ ref_arm_3688], sometimes in 



combination with filing [ref_arm_3723]. 



On breastplates attributed to workshops in Western Europe, like France, Spain or Flanders, 



the cutout for the throat might form a central small nose [ ref_arm_3518] [ref_arm_3570] 



[ref_arm_3465]. Also at least one example made in the style of the German speaking lands 



exists [ref_arm_3703].
S. 78 · Sprachlich überarbeitet · Entwurf

4.1.2.7 Type g: a triangular roll with a concave side

[ref_ill_edg_g] [ref_vid_edg_g] This form occurs exclusively on armour made in German-speaking regions. It resembles Type f, but the side between the apex and the cut edge is concave in section. Such edges are found only on breastplates from the last quarter of the fifteenth century, probably all made in Augsburg [ref_arm_3668] PDF [ref_arm_3614] PDF [ref_arm_3695] PDF [ref_arm_3757] PDF [ref_arm_3601] PDF [ref_arm_4049] PDF.

One breastplate has a small central projection at the neck opening [ref_arm_3671] PDF. Decoration includes filed roping [ref_arm_3613] PDF, while [ref_arm_3615] PDF and [ref_arm_3611] PDF have an engraved or filed line and punched dots along the cut edges.

Originalwortlaut vergleichen
4.1.2.7 Type-g [ref_ill_edg_g] [ref_vid_edg_g] 



This edge-type is found exclusively  on armour made in the German speaking lands. It is 



basically similar to type -f, but in section the side of the triangle between the point and the 



cut plate edge is shaped concave. Such turned edges are found on ly on breastplates of the 



last quarter of the  15th century – probably all made in Augsburg [ ref_arm_3668] 



[ref_arm_3614] [ ref_arm_3695] [ ref_arm_3757] [ ref_arm_3601] [ ref_arm_4049]. One 



breastplate has a small nose at the center of the turned ed ge at the throat cutout 



[ref_arm_3671]. For example [ref_arm_3613] is decorated by a roped -filing, the cut-edges 



of the breastplates [ref_arm_3615] and [ref_arm_3611] are decorated by an engraved or filed 



line and punched dots.
S. 79 · Sprachlich überarbeitet · Entwurf

4.1.2.8 Type h: an open, double-angled edge

[ref_ill_edg_h] [ref_vid_edg_h] Type h is not fully turned. The plate is first bent outwards through approximately 45°, then inwards through approximately 45°. The sides of the resulting section are about 5–7 mm long. This treatment primarily stiffens the plate; the cut edge remains relatively sharp.

It occurs only on German armour from the last quarter of the fifteenth century, including the upper edges of thigh defences [ref_arm_2412] PDF, the edges of elbow shells [ref_arm_283] PDF, and the upper edges of shoulder defences [ref_arm_282] PDF. Several examples occur along the lower edges of pelvic lames [ref_arm_3479] PDF [ref_arm_3284] PDF.

An engraved or filed line often follows the first bend [ref_arm_3311] PDF. On [ref_arm_3296] PDF, “pointillier” decoration occurs along the edge where the chest plate overlaps the inserted nape plate. The upper edge of [ref_arm_2412] PDF has embossed and filed rope-like decoration.

Redaktionelle Hinweise · 1
  • Das Original nennt bei ref_arm_3296 ausdrücklich „thorax-plate“ und „nape-plate“. Diese anatomisch auffällige Verbindung wurde nicht stillschweigend zu einer Rückenplatte korrigiert; am Objekt prüfen.
Originalwortlaut vergleichen
4.1.2.8 Type-h [ref_ill_edg_h] [ref_vid_edg_h] 



The type-h edges are again not completely turned. The plate is first angled outwards to about 



450 and then angled inwards again to about 450. The sides of the section maybe have a length 



of about 5 -7 mm. This edge -conditioning mainly serves as a stiffening of the plate – the 



edges remain relatively sharp. It is found at German armour of the last quarter of the 15 th 



century only. The upper edges of upper legs  [ref_arm_2412], the edges of elbow -shells 



[ref_arm_283] and the upper edges of shoulders [ref_arm_282] for example can be designed 



this way. In several cases, this type of edge is applied to the lower edges of pelvis -lames 



[ref_arm_3479] [ ref_arm_3284]. Often a line is engraved or filed along the first angle 



[ref_arm_3311]. At [ref_arm_3296] the edge where the thorax -plate overlaps the inserted 



nape-plate a “pointillier ” decoration is applied. The upper edge at [ ref_arm_2412] is 



embossed rope-like and filed.
S. 79 · Sprachlich überarbeitet · Entwurf

4.1.2.9 Type i: a three-bend open profile

[ref_ill_edg_i] [ref_vid_edg_i] The edge is first bent outwards through approximately 60–70°, then back to its original orientation, and finally inwards through another 60–70°. The resulting cross-section resembles an inverted pan.

Often decorated with embossed roping, this form occurs from about 1490 on Italian Type VII helmets [ref_arm_1855] PDF [ref_arm_2035] PDF, on a German backplate [ref_arm_3268] PDF, and along the upper edges of Italian thigh defences. Plain versions are very common along the upper edges of backplates where the separate nape plate overlaps them [ref_arm_3310] PDF [ref_arm_3267] PDF.

Originalwortlaut vergleichen
4.1.2.9 Type-i [ref_ill_edg_i] [ref_vid_edg_i] 



Edges of type-i are first angled outwards at about 60-700, then back to the starting angle and 



inwards again by 60 -700. The section is that of a pan turned upside down. Such edges are 



often rope -like embossed and found from about 1490 at Italian helmets of type -VII 



[ref_arm_1855] [ref_arm_2035]; at one German backplate [ ref_arm_3268] or at the upper 



edges of upper leg-protections of Italian production. Plain versions are very often applied to 



the upper edge of backplates wher e the inserted nape -plate overlaps [ ref_arm_3310] 



[ref_arm_3267].
S. 79–80 · Sprachlich überarbeitet · Entwurf

4.1.3 Embossing

The stiffening effect of ridges and corrugations has been understood since antiquity. The Celts used it on shield bosses, for example, and the Greeks reinforced the edges of Illyrian-type helmets in this way. Most surviving late medieval armour incorporates elongated embossed features. Ridges occur on knee defences from at least the mid-fourteenth century [ref_ill_art_5157] PDF [ref_arm_2282] PDF. They were long interpreted solely as a means of strengthening the plate against penetration by weapons, but this was probably only one reason for their use. Their initial appearance more likely reflected an imitation of pleated clothing, since developments in armour and textile fashions were closely connected.89

In general, elongated embossing appears earlier on armour made in German-speaking regions than on Italian products. Fifteenth-century armour from either region rarely has relief decoration depicting figures or symbols. Unique examples include the breastplate [ref_arm_3721] PDF, embossed with a rudimentary face, and [ref_arm_3678] PDF, embossed with a heart.

Like turned edges, ridges and corrugations offer evidence for grouping related objects. Despite their significance, Bruno Thomas appears to have made the only attempt to classify these features.90 His drawings apply chiefly to armour dating from about 1500 onwards and do not define the different forms of medial ridge.

Two broad categories must be distinguished:

  • Elongated surface decoration, either raised as a ridge or recessed as a corrugation, primarily decorative in character.
  • Raised medial ridges that divide an object along its centre into two usually symmetrical halves.

Both can be produced by several methods, generally after the object has received its overall shape. The simplest begins by marking the course of each edge of the intended feature on the inside of the plate with a chisel. When supported on a soft material such as lead or wood, the plate may already acquire a slight relief from the force of the chisel blows. Some form of chisel holder was probably used to make this work easier, resembling that shown in [ref_ill_art_5361] PDF.

The plate is then placed on an angular stake and hammered from the outside. The marked lines guide its precise placement. The hammer strikes just below the highest point of the stake, driving the surrounding plate down to form the relief. Heating is not necessary for this operation.

Originalwortlaut vergleichen
4.1.3 Embossing 



The reinforcing or stiffening effect of ridges or corrugations is known since antiquity, when 



for example the Celts used this feature at the bosses of their shields or when the Greeks gave 



stability to the edges of helmets of the Illyrian type. Most of the extant late medieval armour 



parts show elongated embossing at the plates. From at least the mid-14th century on, the 



plates at the knees were decorated by ridges [ref_ill_art_5157] [ref_arm_2282]. It was long 



thought that these features were meant to stiffen the plate against arm penetration only. This 



might be only one of the reasons why they were applied to armour. The aspect of imitating 



the pleats of textile clothing is rather likely to have been the archetype for the first appearance 



of ridges – last but not least as textile - and armour-fashion always went hand in hand. 89 



Generally, it can be noted that armour made in the German speaking lands is earlier decorated 



with elongated embossing than armour of Italian make. In the fifteenth century in both 



regions, relief -like embossing of symbols or images was very rarely execut ed. Unique 



examples are the breastplate [ref_arm_3721], with the embossing of a primitive face and the 



breastplate [ref_arm_3678], with the embossing of a heart.  



Like turned edges, also ridges and corrugations can tell a lot about armour – groups of 



different objects related by their embossing might be assembled. Despite the significance of 



the information delivered by different embossing types, the only att empt to classify 



embossing seems to have been made by Bruno Thomas.90 His drawings are for the most part 



only relevant for armour from about 1500 or later. He does not define the different medial -



ridge types.  



Two large blocks of embossing need to be distinguished:



1. Raised (ridge) or recessed (corrugation) elongated embossing on the surface of 



merely decorative character. 



2. Raised medial ridges that split an armour part medially into two (usually) 



symmetrical halves. 



Both elongated embossing-types can be applied to a plate by different methods. Usually the 



general shape of the item is finished first. The simplest way is then to chisel the course of 



each edge of the later embossing to the interior surface of the plate. Placing the plate on a 



soft support, like lead or wood, – depending on the used force of the hammer-work – would 



already allow a slight embossing from the chisel punched into the plate. It is very likely that 



the workers used some kind of chisel-handle to ease this work, similar to the one seen in the 



painting [ref_ill_art_5361]. The plate is then placed on an edged stake and worked with the 



hammer from the exterior. The lines marked with the chisel will allow an exact placing of 



the plate on the stake. The hammer would always hit slightly beneath the highest spot of the 



stake, driving down the plate to reveal an embossing. It is not necessary to heat the plate for 



this work.
S. 80 · Sprachlich überarbeitet · Entwurf

4.1.3.1.1 Type a: a simple raised ridge

[ref_ill_rid_a] The simplest raised ridge has a cross-section resembling a mountain peak rising from a flat surface. Several such ridges occur in parallel, chiefly on armour made in German-speaking regions [ref_arm_9] PDF [ref_arm_1067] PDF [ref_arm_2304] PDF [ref_arm_3264] PDF. They are sometimes accompanied by parallel filed lines [ref_arm_3668] PDF. Their paths generally follow the curves of adjacent plate edges. This form appears in the second half of the fifteenth century.

Originalwortlaut vergleichen
4.1.3.1.1 Type-a [ref_ill_rid_a] 



This type of ridge is the simplest version. It is only raised and in profile it forms a “mountain 



pike” rising from a plane surface. Merely on armour made in the German speaking lands 



several of  such ridges are applied in parallel lines [ ref_arm_9] [ ref_arm_1067] 



[ref_arm_2304] [ref_arm_3264]. Sometimes they are accompanied by parallel filed lines 



[ref_arm_3668]. The lines of these ridges are usually following the curve of the neighboring 



plate-edges. They appear at armour in the second half of the 15th century.
S. 80 · Sprachlich überarbeitet · Entwurf

4.1.3.1.2 Type b: a rounded recessed groove

[ref_ill_rid_b] Type b is recessed below the plate surface, forming a concave valley or groove. It is likewise characteristic of armour north of the Alps. Several parallel grooves may decorate a plate, sometimes accompanied by filed lines [ref_arm_19] PDF. Occasionally, grooves intersect [ref_arm_1075] PDF. They usually curve along an adjacent plate edge [ref_arm_364] PDF. This feature was used only in the last quarter of the fifteenth century.

Originalwortlaut vergleichen
4.1.3.1.2 Type-b [ref_ill_rid_b] 



This embossing is recessed from the plate surface. It forms a concave “valley” or groove on 



a plane surfa ce. This is again a feature of the northern -alpine taste and also here several 



parallel corrugations can decorate the plate-surface – occasionally with accompanying filed 



lines [ref_arm_19]. In a few cases these embossing can cross others [ref_arm_1075]. These 



embossing occurs usually in curved lines following the neighboring plate -edge 



[ref_arm_364]. This feature was used only in the last quarter of the 15th century.
S. 80 · Sprachlich überarbeitet · Entwurf

4.1.3.1.3 Type c: a series of steps

[ref_ill_rid_c] In section, Type c resembles a row of steps or the teeth of a saw. It always occurs as a group of steps, sometimes with a parallel filed line beside each ridge [ref_arm_304] PDF. This form occurs exclusively on German armour between the 1470s and 1500. It can decorate any part, including breastplates [ref_arm_3632] PDF, backplates [ref_arm_3319] PDF, and the cuffs of Type III or IV hand protection [ref_arm_1064] PDF [ref_arm_1075] PDF.

Originalwortlaut vergleichen
4.1.3.1.3 Type-c [ref_ill_rid_c] 



The section of a ridge of type c forms a row of several steps, similar to a saw-blade. Always 



a bundle of steps decorates the surface. Each ridge is occasionally accompanied by parallel 



filed lines [ref_arm_304]. This embossing type is found exclusively at German armour from 



the 1470ies to 1500. All armour parts can be decorated by these ridges, for example 



breastplates [ref_arm_3632] and backplates [ ref_arm_3319] or the cuffs of type -III or -IV 



hand-protections [ref_arm_1064] [ref_arm_1075].
S. 80 · Sprachlich überarbeitet · Entwurf

4.1.3.1.4 Type d: a sharply defined raised ridge

[ref_ill_rid_d] This form first appears around 1490 on armour made in German-speaking regions [ref_arm_1207] PDF. It differs from Type a in the sharper angles where each side of the ridge meets the plate surface. Parallel lines emphasise these junctions. Thus, the valley between neighbouring Type d ridges contains two filed lines, whereas a Type a ridge is accompanied by either one line or none. In the early sixteenth century, these ridges—called “Riefel” in German—became the most common embossed decoration on German [ref_arm_3473] PDF [ref_arm_8] PDF and Italian armour.

Originalwortlaut vergleichen
4.1.3.1.4 Type-d [ref_ill_rid_d] 



This type of ridge occurs for the first time about 1490 on armour made in the German 



speaking lands [ref_arm_1207]. Its main difference to the section of a ridge of type -a is the 



sharper angles at the two feet of the “mountain”. These are further  emphasized by 



accompanying parallel lines. Therefore, in each “valley” between two or more of such ridges 



two parallel filed lines are found while a type -a ridge is accompanied by no or one single 



line only. In the early 16 th century these ridges – in German called “Riefel” – became the 



most common embossing-type for German [ref_arm_3473] [ref_arm_8] and Italian armour.
S. 81 · Sprachlich überarbeitet · Entwurf

4.1.3.1.5 Type e: an inverted Type a profile

[ref_ill_rid_e] Type e is made in the same way as Type a, but with the profile inverted. Such recessed features often decorate the back of hand protection [ref_arm_1336] PDF [ref_arm_1305] PDF [ref_arm_1066] PDF [ref_arm_1088] PDF and also occur on the breastplate [ref_arm_3428] PDF. This form was used from the 1430s to the end of the century.

Originalwortlaut vergleichen
4.1.3.1.5 Type-e [ref_ill_rid_e] 



Type-e embossing are made exactly the same way like ridges of type -a, but here the inside 



is turned out. Often at hand -protections the back of the hand is decorated with such 



corrugations [ref_arm_1336] [ref_arm_1305] [ref_arm_1066] [ref_arm_1088], but also the 



breastplate [ref_arm_3428] shows this feature. This type of ridge decorated armour from the 



1430ies until the end of the century.
S. 81 · Sprachlich überarbeitet · Entwurf

4.1.3.1.6 Type f

[ref_ill_rid_f] Type f is produced by a process very similar to that used for Type b corrugations. A few early examples occur on elbow [ref_arm_955] PDF and knee defences [ref_arm_2919] PDF. Between 1470 and 1510 in German-speaking regions, the form occurs chiefly on the backs of certain Type III [ref_arm_1061] PDF [ref_arm_1096] PDF and Type IV hand defences [ref_arm_1245] PDF [ref_arm_1274] PDF, on armpit protection [ref_arm_128] PDF [ref_arm_129] PDF, and on the pelvic lames of backplates [ref_arm_3311] PDF.

Redaktionelle Hinweise · 1
  • Das Original definiert den Querschnitt von Typ f nicht ausdrücklich im Fließtext. Keine zusätzliche Formbeschreibung aus einer ungeprüften Zeichnung ergänzt.
Originalwortlaut vergleichen
4.1.3.1.6 Type-f [ref_ill_rid_f] 



The making of type-f is very similar to the making of type-b corrugations. Type-f embossing 



is found in few early cases at the elbows [ ref_arm_955], the knees [ ref_arm_2919], but in 



the German speaking lands between 1470 and 1510 merely at the back of the hand on certain 



variations of type -III [ ref_arm_1061] [ ref_arm_1096] or -IV [ ref_arm_1245] 



[ref_arm_1274] hand-protections, at armpit protections [ ref_arm_128] [ref_arm_129] or at 



the pelvis-lames of backplates [ref_arm_3311].
S. 81 · Sprachlich überarbeitet · Entwurf

4.1.3.1.7 Type g: a flat-topped raised band

[ref_ill_rid_g] The section resembles a flat-topped mountain or raised plateau. Because it consists of two steps, its manufacture is similar to that of Type c. It occurs in the last quarter of the fifteenth century, for example on thigh defences [ref_arm_2406] PDF. Variants have filed roping [ref_arm_246] PDF or embossed decoration [ref_arm_2901] PDF [ref_arm_3725] PDF.

Originalwortlaut vergleichen
4.1.3.1.7 Type-g [ref_ill_rid_g] 



The section of this ridge -type can be described as a “flat -topped mountain” or “elevated 



plain”. As it actually consists of two “steps”, its making is similar to the making of type -c 



ridges. Type-g ridges are found in the last quarter of the  15th century for example at upper 



legs [ ref_arm_2406] – in a rope -like filed [ ref_arm_246] or embossed variation at 



[ref_arm_2901] [ref_arm_3725].
S. 81 · Sprachlich überarbeitet · Entwurf

4.1.3.1.8 Type h: a single step

[ref_ill_rid_h] Type h forms a single step in the plate surface and is made by a process similar to that used for Type c. On the thigh defences [ref_arm_2410] PDF [ref_arm_2809] PDF, these ridges form two arcs. They also run parallel to the arm openings on the backplate [ref_arm_3279] PDF and breastplate [ref_arm_3653] PDF. This feature was used from the 1460s to the 1480s.

Originalwortlaut vergleichen
4.1.3.1.8 Type-h [ref_ill_rid_h] 



A ridge of type-h is a single step in the surface; its making is similar to t he making of type-



c ridges. At the upper legs [ ref_arm_2410] [ref_arm_2809] type-h ridges form two bows, 



also in parallel to the arm cutouts at the backplat e [ ref_arm_3279] or the breastplate 



[ref_arm_3653]. This feature was used from the 1460ies to the 1480ies.
S. 82 · Sprachlich überarbeitet · Entwurf

4.1.3.2 Medial ridges

Medial ridges were the first ridges to appear on late medieval plate armour. They are more likely to have served a stiffening function than the surface decoration described above, but reinforcement cannot have been their only purpose. Throughout the main period of plate-armour production, many helmets lacked a ridge along the top of the skull [ref_arm_4343] PDF [ref_arm_1702] PDF [ref_arm_2086] PDF. Early Type I hand protection and Italian arm protection, apart from shoulder defences, also lacked medial ridges. Italian breastplates had them only when made for export to northern Europe.

Backplates never had a medial ridge, except on their pelvic lames, because of the convex shape of the main plate. Towards the end of the fifteenth century, breastplates from German-speaking regions often omitted the ridge [ref_arm_3425] PDF, although it had been used there for many years. These objects were certainly not regarded as less protective. Decisions to include or omit a medial ridge therefore also reflected considerations of design.

Medial ridges are made by essentially the same method as surface embossing, but many have different cross-sections. The following classification distinguishes these forms.

Redaktionelle Hinweise · 1
  • Die absoluten Aussagen zu regionalen Vorkommen und zu Rückenplatten bleiben als Aussagen der Dissertation erhalten. „Convex“ wurde nicht anatomisch umgedeutet; Betrachtungsseite gegebenenfalls präzisieren.
Originalwortlaut vergleichen
4.1.3.2 Medial ridges 



Medial ridges are the first ridges to appear at late medieval plate armour. They are much 



more likely to have had a stiffening function than the surface embossing described above. 



But also here this cannot be the only reason for their application, as many objects from the 



beginning of the g reat period of plate armour until its end do not necessarily show central 



ridges at the top of the skulls [ref_arm_4343] [ref_arm_1702] [ref_arm_2086]. Early type-I 



hand-protections and also no Italian arm -protection – with the exception of the shoulders – 



had a medial ridge and only Italian breastplates made for export to northern Europe had such 



an embossing. No backplate (except of the pelvis -lames) ever had a medial ridge – due to 



the convex shape of the plate. After medial ridges had been applied to breastplates for years, 



by the end of the 15 th century also in the German speaking lands th is feature was often 



omitted [ref_arm_3425]. These items were for sure not considered as less protective. So here 



the design aspect was again also part of the armourer’s intention when leaving or adding a 



medial ridge.  



The making of a medial ridge is basically the same as the making of a surface embossing. 



Nevertheless, many types have a section different to the aforesaid ridges and corrugations. 



In the following the various types will be classified and described.
S. 82 · Sprachlich überarbeitet · Entwurf

4.1.3.2.1 Type a: a pointed-arch section

[ref_ill_med_a] This section resembles the pointed arch of Gothic architecture. It occurs on all kinds of helmets from the early fourteenth to the early sixteenth century [ref_arm_1456] PDF [ref_arm_1364] PDF [ref_arm_1446] PDF [ref_arm_1982] PDF [ref_arm_1918] PDF, and on many breastplates from the second half of the fifteenth century [ref_arm_3438] PDF [ref_arm_3458] PDF [ref_arm_4076] PDF.

All thigh [ref_arm_2909] PDF, knee [ref_arm_2987] PDF and lower-leg defences [ref_arm_2295] PDF have medial ridges of this type. It also occurs on most neck defences [ref_arm_3034] PDF, thigh protection attached to the torso [ref_arm_3858] PDF, and hand-protection cuffs [ref_arm_1064] PDF [ref_arm_1205] PDF. In Germany, it may occur on any form of arm protection [ref_arm_312] PDF [ref_arm_306] PDF; Spanish elbow defences also share this feature [ref_arm_12] PDF.

Redaktionelle Hinweise · 1
  • Das pauschale „all“ für Oberschenkel-, Knie- und Unterschenkelschutz stammt aus dem Original. Der Geltungsbereich sollte bei der fachlichen Durchsicht gegebenenfalls eingegrenzt werden.
Originalwortlaut vergleichen
4.1.3.2.1 Type-a [ref_ill_med_a] 



The section of a medial ridge of type -a reminds on a pointed arch or bow in the gothic 



architecture. This type of ridge is found at all kinds of helmets from the early 14th century to 



the early 16 th century [ ref_arm_1456] [ ref_arm_1364] [ ref_arm_1446] [ ref_arm_1982] 



[ref_arm_1918]. Also many breastplates of the second half of the 15th century have a type-a 



ridge [ ref_arm_3438] [ ref_arm_3458] [ ref_arm_4076]. All upper legs [ ref_arm_2909], 



knees [ref_arm_2987], lower legs [ref_arm_2295] have a medial ridge of this type. Most of 



the neck defenses [ref_arm_3034], torso-leg-protections [ref_arm_3858], hand-protection-



cuffs [ref_arm_1064] [ref_arm_1205] have such a ridge applied as well. In Germany all arm-



protections can have a type -a medial ridge [ ref_arm_312] [ref_arm_306] and also Spanish 



elbows share this feature [ref_arm_12].
S. 82 · Sprachlich überarbeitet · Entwurf

4.1.3.2.2 Type b: a prominent ridge with concave sides

[ref_ill_med_b] Type b projects strongly from the plate surface and has concave sides. An early fifteenth-century effigy in Wertheim shows a breastplate with a particularly pronounced example [ref_ill_art_5272] PDF (description 2). No comparable breastplate of that date survives.

From the 1430s, Type b occurs on all helmet types [ref_arm_2030] PDF [ref_arm_1382] PDF [ref_arm_1348] PDF [ref_arm_1721] PDF [ref_arm_1945] PDF. From the second half of the fifteenth century, it becomes common on elbow defences [ref_arm_21] PDF, western European breastplates [ref_arm_3518] PDF [ref_arm_3624] PDF, German breastplates [ref_arm_3593] PDF [ref_arm_3497] PDF, and Italian breastplates made for export to northern Europe [ref_arm_3649] PDF, together with their attached thigh protection [ref_arm_3817] PDF.

Originalwortlaut vergleichen
4.1.3.2.2 Type-b [ref_ill_med_b] 



This type of medial ridge is strongly embossed from the plate surface and shows concave 



sides. An early 15th century depiction of a very strong medial ridge of type -b is found at a 



breastplate depicted at an effigy in Wertheim [ ref_ill_art_5272] (descr. 2). No similar 



breastplate of this date is preserved. From the 1430ies on, medial ridges of type-b are applied 



to all types of helmets [ ref_arm_2030] [ ref_arm_1382] [ ref_arm_1348] [ ref_arm_1721] 



[ref_arm_1945]; from the second half of the 15 th century they become commonly attached 



to elbows [ ref_arm_21], to Western European [ ref_arm_3518] [ ref_arm_3624], German 



[ref_arm_3593] [ ref_arm_3497] and Italian breastplates (for export to northern Europe) 



[ref_arm_3649] together with their torso upper-legs [ref_arm_3817].
S. 82–83 · Sprachlich überarbeitet · Entwurf

4.1.3.2.3 Type c: a flat-topped medial ridge

[ref_ill_med_c] Type c has a section resembling a raised plateau and occurs between about 1480 and 1510. It is rare on German breastplates [ref_arm_3658] PDF and knee defences [ref_arm_2868] PDF. On the hand defences [ref_arm_1207] PDF, each knuckle at the base of the fingers has a Type c ridge decorated by filing.

German Type VII helmets often have this medial ridge [ref_arm_1730] PDF [ref_arm_1692] PDF, sometimes with filed lines [ref_arm_1845] PDF. Filed lines also often occur near a small hole in the centre of the skull or ridge [ref_arm_1800] PDF; their purpose is unknown. Helmets are the only Italian armour objects to carry this form [ref_arm_1442] PDF [ref_arm_1752] PDF. Some Type VII helmets attributed to France or Flanders also have it [ref_arm_1718] PDF.

Originalwortlaut vergleichen
4.1.3.2.3 Type-c [ref_ill_med_c] 



The section of this medial ridge looks like an “elevated plain”. This type was applied to 



armour between 1480 ca. and 1510. It is rarely found at German breastplates [ref_arm_3658] 



and knees [ ref_arm_2868]. At the hand -protections [ ref_arm_1207] each knuckle at the 



finger-root has a type -c ridge with decorative filing applied. German helmets of type -VII 



often have a type-c medial ridge [ ref_arm_1730] [ref_arm_1692], in some cases decorated 



with filed lines [ref_arm_1845]. German type-VII helmets often show some filed lines close 



to a small hole in the central skull/ridge [ref_arm_1800]. The purpose of these lines remains 



obscure. Helmets are the only Italian armour parts to have such a ridge applied



[ref_arm_1442] [ref_arm_1752]. Some type-VII helmets – said to be of French or Flemish 



production – have a medial ridge of type-c embossed as well [ref_arm_1718].
S. 83 · Sprachlich überarbeitet · Entwurf

4.1.3.2.4 Type d: a combined Type a and c profile

[ref_ill_med_d] Type d combines features of Types a and c. The only surviving example known to me is [ref_arm_1810] PDF.

Originalwortlaut vergleichen
4.1.3.2.4 Type-d [ref_ill_med_d] 



This type is a kind of combination between a type -a and a type -c medial ridge. The only 



extant example known to the author to have such a ridge is [ref_arm_1810].
S. 83 · Sprachlich überarbeitet · Entwurf

4.1.3.2.5 Type e: two parallel Type b ridges

[ref_ill_med_e] Type e consists of two parallel Type b medial ridges. A plain example occurs on the Type VII helmet [ref_arm_1690] PDF; filed decoration appears on [ref_arm_1881] PDF [ref_arm_1862] PDF. I know this form only on Type VII helmets.

Originalwortlaut vergleichen
4.1.3.2.5 Type-e [ref_ill_med_e] 



A type-e ridge consists of two parallel type -b medial ridges. A plain version is found for 



example at the type-VII helmet [ref_arm_1690] or file-decorated variants at [ref_arm_1881] 



[ref_arm_1862]. The author knows this type only from helmets of type-VII.
S. 83 · Sprachlich überarbeitet · Entwurf

4.1.3.2.6 Type f: three parallel Type b ridges

[ref_ill_med_f] Type f consists of three parallel Type b ridges and occurs exclusively on a few Type VII helmets. According to its display label, [ref_arm_1899] PDF is a reproduction made by the Ernst Schmidt workshop in Munich. Its marks instead suggest manufacture by Winkelmayer in Vienna.91

Three further helmets [ref_arm_1875] PDF [ref_arm_4591] PDF [ref_arm_4543] PDF are so similar in shape and decoration that they were most probably made in a single workshop. They share numerous features, particularly the many surface ridges on their skulls and nape guards. All these helmets are highly likely to be reproductions. If so, Type f may not have been used by late medieval armourers.

Originalwortlaut vergleichen
4.1.3.2.6 Type-f [ref_ill_med_f] 



This type consists of three parallel type -b ridges. This feature is found exclusively at a few 



type-VII helmets. The example [ ref_arm_1899] is a reproduction – according to the 



showcase-label – made by the Atelier Ernst Schmidt in Munich. The marks do rather suggest 



that this helmet was made by Winkelmayer in Vienna 91. The other items [ ref_arm_1875] 



[ref_arm_4591] [ ref_arm_4543] are most likely made in one workshop, as all are very 



similar to each other in shape and decoration. All three helmets share some common features, 



especially the many surface -ridges on the skull and the nape -guard. There is a high 



probability that all these helmets are reproductions. If this is true, type -f ridges might not 



have been known to armourer’s in the late Middle Ages.
S. 83 · Sprachlich überarbeitet · Entwurf

4.1.3.2.7 Type g: two narrow Type c ridges

[ref_ill_med_g] Type g consists of two narrow, parallel Type c ridges. Examples include [ref_arm_4448] PDF [ref_arm_4325] PDF. Their ridge decoration closely resembles that of the Type VII helmets with Type f medial ridges discussed above. These helmets are also very likely to be reproductions by the same Viennese maker.

Originalwortlaut vergleichen
4.1.3.2.7 Type-g [ref_ill_med_g] 



The type -g medial ridge is defined by two parallel, narrow type -c ridges. Examples are 



[ref_arm_4448] [ref_arm_4325]. Both have many similarities in the ridge decoration to the 



aforesaid type-VII helmets with a medial ridge of type -f. It is very likely that also these 



helmets are reproductions made by the aforesaid Vienna Master.
S. 83 · Sprachlich überarbeitet · Entwurf

4.1.3.2.8 Type h: a combined Type a and b profile

[ref_ill_med_h] Type h combines Types a and b. Examples include [ref_arm_2035] PDF, [ref_arm_4452] PDF—probably a reproduction—and [ref_arm_4589] PDF.

Originalwortlaut vergleichen
4.1.3.2.8 Type-h [ref_ill_med_h] 



This is a combination of a type -a and a type -b medial ridge, found for example at 



[ref_arm_2035] [ref_arm_4452] (probably a reproduction) and [ref_arm_4589].
S. 83 · Sprachlich überarbeitet · Entwurf

4.1.3.2.9 Type i: two superimposed Type c profiles

[ref_ill_med_i] Type i consists of two Type c profiles superimposed vertically. At least two Type VII helmets have this feature [ref_arm_1757] PDF [ref_arm_1837] PDF.

Originalwortlaut vergleichen
4.1.3.2.9 Type-i [ref_ill_med_i] 



A type-i ridge consists of two piled type -c ridges. At least two type -VII helmets show this 



feature [ref_arm_1757] [ref_arm_1837].
S. 83 · Sprachlich überarbeitet · Entwurf

4.1.3.2.10 Type j: a convex section

[ref_ill_med_j] Type j has a convex cross-section. Examples occur on breastplates probably made in German-speaking regions around 1490 [ref_arm_3580] PDF [ref_arm_3789] PDF, and on two Italian Type V helmets [ref_arm_2024] PDF—possibly a reproduction—and [ref_arm_2052] PDF.

The two Type IV helmets with this feature [ref_arm_1499] PDF [ref_arm_1510] PDF are most likely reproductions from one workshop. Comparable helmets never have a Type j ridge, which generally occurs on objects later than the stylistic dates of these examples. Moreover, their skulls were not formed deeply from a single plate: instead, a plate was rolled into a cone and joined along a seam running from the apex to the brow.

Originalwortlaut vergleichen
4.1.3.2.10 Type-j [ref_ill_med_j] 



This type of medial ridge has a convex section. It is found for example at breastplates, 



presumably made in the German speaking lands about 1490 [ref_arm_3580] [ref_arm_3789] 



and two Italian helmets of type-V [ref_arm_2024] (reproduction?) [ref_arm_2052]. The two 



type-IV helmets [ ref_arm_1499] [ ref_arm_1510] with this feature are most likely 



reproductions made by one workshop. Comparable examples never have a type-j ridge, it is 



also a feature usually found at items of younger date than the style -date of the aforesaid 



helmets. Furthermore, the skulls are not deep -drawn from one plate, but cone -like rolled 



from a plate with the edges connected at a seam, leading from the point to the brow.
S. 84–85 · Sprachlich überarbeitet · Entwurf

4.1.4.1 Edge decoration

Unturned plate edges may be decorated with applied elements or ornament cut directly into the metal. Four principal techniques can be distinguished, often in combination on a single object.

1. Shaping the cut edge into a succession of convex or concave curves. The outline was probably cut roughly with shears and then finished with a file. This treatment is characteristic of armour made in German-speaking regions during the second half of the fifteenth century. Concave curves usually occur along overlapping lame edges, for example on shoulder [ref_arm_329] PDF, pelvic [ref_arm_3623] PDF, abdominal [ref_arm_3604] PDF and neck protection [ref_arm_3059] PDF. They occur less often on the abdominal plates of Italian breastplates [ref_arm_3716] PDF and on thigh protection attached to the torso [ref_arm_3817] PDF. On Italian armour from the mid-fifteenth century, the lame joining the elbow to the forearm usually has this treatment [ref_arm_882] PDF, as do some shoulder lames [ref_arm_715] PDF and, frequently, the upper plates of back protection [ref_arm_3404] PDF.

Convex curves often occur along overlapping edges on rear pelvic lames [ref_arm_3360] PDF, on the backs of hand defences [ref_arm_1061] PDF, at the ends of visor arms [ref_arm_1702] PDF, and along the lower edge of the lowest lame [ref_arm_3302] PDF. Both concave and convex outlines remained in use on overlapping edges into the first third of the seventeenth century.

2. Filing a simple toothed pattern into the cut edge. This required a file much like those used today. Italian armour from the second half of the fifteenth century often has toothed filing close to the points of overlapping plate edges [ref_arm_861] PDF [ref_arm_3817] PDF [ref_arm_3410] PDF. A few Italian breastplates also have simple filed decoration along the upper edge of the abdominal plate [ref_arm_3721] PDF. On more costly armour from German-speaking regions, overlapping edges often carry delicate filed ornament [ref_arm_1064] PDF, frequently combined with pierced work.

3. Piercing ornamental openings near the cut edge. An opening was first drilled or punched, then shaped with files. This technique occurs only on expensive armour made in German-speaking regions during the last third of the fifteenth century. It was generally confined to overlapping edges, probably to prevent the delicate ornament from catching clothing or skin. The lower edges of some knee defences count as overlapping edges in this context, since leg protection with such pierced decoration was always worn with lower-leg defences [ref_arm_4701] PDF.

The central point of a Type IV abdominal plate was often pierced with floral ornament [ref_arm_3587] PDF, although almost any overlapping edge could be decorated in this way. Augsburg probably produced the most accomplished practitioners, particularly the Helmschmied family [ref_arm_3300] PDF [ref_arm_3695] PDF [ref_arm_5094] PDF. Their ornament often resembles plants growing out of the plate edge, comparable to carved architectural decoration north of the Alps. Floral pierced edges ceased to be produced in German-speaking regions around 1500; [ref_arm_3363] PDF may be a late example. Italian armourers made little use of elaborate pierced decoration.

4. Decorating a band along the edge by filing, engraving, etching, gilding or related techniques. Bands of ornament punched with small chisels—the “pointillier” technique—occur on Italian armour from the second half of the fourteenth century, sometimes combined with filed or engraved lines [ref_arm_1251] PDF. Italian armourers continued to decorate costly products in this way until the late fifteenth century [ref_arm_3723] PDF. Previously unrecognised examples also occur on German armour [ref_arm_3322] PDF [ref_arm_3318] PDF. On some German objects from the final two decades of the century, each convex curve at the edge is decorated with a small crescent-shaped stamp [ref_arm_1272] PDF [ref_arm_3447] PDF.

Helmschmied armourers often filed a line parallel to the edge, approximately 3 mm from it, then added short lines running to the edge to create a toothed or rope-like band [ref_arm_1207] PDF. These bands may originally have been gilded on all surviving examples, as the remaining gold on the shoulder defence [ref_arm_5098] PDF suggests. Shoulder defences depicted around 1600 [ref_ill_art_5163] PDF provide further evidence for this treatment.

In the early sixteenth century, many expensive suits of armour had borders combining blueing, gilding and etching. The earliest surviving example with gilded ornament on a blue band along the lower edge is the Type VII helmet [ref_arm_1971] PDF, probably made in Augsburg in the 1490s.

Redaktionelle Hinweise · 1
  • Die Aussage zur stets gemeinsamen Nutzung bestimmter durchbrochen verzierter Knie- und Unterschenkelpanzerung wurde als spezifische Aussage des Originals erhalten. Sie ist keine allgemeine Regel für die Zuordnung isolierter Objekte.
Originalwortlaut vergleichen
4.1.4.1 Edges 



The not-turned plate edges of at some items are decorated either by applications directly cut 



into the plate. Four main technique-groups can be distinguished, but they often appear in 



combination at the same object: 



1. The cut-edge is simply shaped by a series of convex or concave bows: 



The edges were probably roughly cut with the help of shears and then filed to the 



final shape. This feature is significant for armour made in the second half of the 15th 



century in the German speaking lands. The concave bows are usually found at the 



overlapping edges of lames, for example at shoulders [ ref_arm_329], pelvis 



protections [ ref_arm_3623], abdomen protections [ ref_arm_3604] or at neck -



protections [ ref_arm_3059]. In fewer cases, also the abdomen -plates of Italian 



breastplates [ref_arm_3716] and torso-upper leg -protections [ ref_arm_3817] are 



decorated by concave cutouts. The lame that connects the elbow to the lower arm on 



Italian armour from the mid-15th century on usually shows this feature 



[ref_arm_882], sometimes also one of the shoulder  lames [ ref_arm_715] and 



frequently the thorax-plates of back-plates [ref_arm_3404]. 



Convex bows are often found for example at overlapping edges of torso-back pelvis-



lames [ref_arm_3360], at the back of the hand [ ref_arm_1061] or the ends of the 



visor-arms [ ref_arm_1702], but also at the lower edge of the lowest lame 



[ref_arm_3302]. The concave and the convex cutouts at overlapping edges are found 



at armour until the first third of the 17th century. 



2. The cut-edge is decorated by simple tooth-like filing:  



This work has been done with the help of a file, not much different to modern 



examples. On Italian armour of the second half of the 15th century, close to the points 



at the overlapping plate edges, of ten tooth -like filings are visible [ ref_arm_861] 



[ref_arm_3817] [ref_arm_3410]. A few Italian breastplates show a simple, filed edge 



decoration at the upper edge of the abdomen -plate [ref_arm_3721]. In the German 



speaking lands, the overlapping edges of more costly armour in many cases are 



delicately decorated by filing [ref_arm_1064], often in combination with fretwork.  



3. Close to the cut edge, the plate is pierced by ornamental fretwork:  



It was first necessary to drill or punch a hole through the plate and then to use a file 



to finish the details. This decoration technique is found only at costly armour parts 



made in the German speaking lands in the last third of the 15 th century. Probably to 



avoid getting stuck in the delicate ornaments  with clothes and flesh , usually only 



overlapping edges are decorated this way. The lower edges of some knees count here 



as overlapping edges as such leg armour decorated with fretwork was always worn 



in combination with lower leg defenses [ref_arm_4701]. Often the central point of a 



type-IV abdomen -plate was decorated with floral fretwork [ ref_arm_3587], but 



nearly any kind of overlapping edge c ould be decorated this way. Probably the 



greatest masters of fretwork came from Augsburg, particularly the Helmschmied 



family cut beautiful ornaments into the plates [ ref_arm_3300] [ ref_arm_3695] 



[ref_arm_5094]. The fretwork often imitates plants that seem to grow out of the edge 



– similar to some masonry -ornaments found frequently at contemporary northern 



alpine architecture. In the German speaking lands, the floral decorations of plate 



edges were not produced anymore after 1500 ca. A late example might be the



backplate [ref_arm_3363]. Italian armourers did not make extensive use of elaborate 



fretwork-techniques. 



4. A stripe of the surface along the edge is decorated either by filing, engraving, etching, 



gilding etc.: 



Ornamented bands, punched into the plate surface with the help of small chisels 



(pointillier), sometimes together with filed or engraved lines, are found on Italian 



armour from the second half of the 14 th century [ ref_arm_1251]. The Italian 



armourers decorated some costly armour this way until the late 15th century 



[ref_arm_3723]. It has not been noted so far that also on German armour surface 



decorations made in the pointillier -technique are to be found [ ref_arm_3322] 



[ref_arm_3318]. On some German items of the last two decades of the 15 th century 



each convex edge -bow is decorated with a small crescent -shaped stamp 



[ref_arm_1272] [ref_arm_3447]. The armourers of the Helmschmied family often in 



parallel to the edge filed a line into the surface, with a distance of approximately 3 



mm. Then they filed small lines to the edge to reveal a tooth- or rope- like appearance 



[ref_arm_1207]. It is possible that at all extant examples this stripe once was gilded, 



as the remaining gold -coating at the shoulder [ ref_arm_5098] suggests. Also the 



shoulders [ref_ill_art_5163] of about 1600 suggest that this feature really existed. In 



the early 16th century many costly suits of armour were decorated at the edges by a 



technique being a combination of blueing, gilding and etching. The oldest extant 



armour to have a blued stripe with gilded ornaments at the lower edge, is the type -



VII helmet [ref_arm_1971], probably made in Augsburg in the 1490ies.
S. 85 · Sprachlich überarbeitet · Entwurf

4.1.4.2 Surfaces

Surface condition can reveal how an object was made, used, maintained and subsequently treated. Each object has two distinct surfaces: an interior that was never ground or polished, and an exterior either left rough or fully ground and polished, sometimes with elaborate decoration. Grinding generally removes external evidence of forging, such as hammer marks and scale. On original objects, ground surfaces are usually completely even.

Most surviving armour no longer retains its original surface condition. Iron-based materials are vulnerable to corrosion, and repeated cleaning during use and later preservation has altered their surfaces. Interior and exterior coatings, together with shallow incised decoration, have often been polished away over the centuries. Close examination is now needed to identify their remains.

Both the exterior and the interior provide evidence about an object. Their respective characteristics are considered below.

Originalwortlaut vergleichen
4.1.4.2 Surfaces 



Surface conditions can tell details about the technology of the production, about the later 



use, maintenance and treatment of a certain object. Two different kinds of surfaces are found 



at each object: One at the interior, never ground and polished; the other one at the exterior, 



either left “rough” or entirely ground, polished and often even elaborately decorated. It has 



to be emphasized that a ground item does exteriorly usually not show remains of the forging 



like hammer scale, hammer -marks etc. The ground surfaces of genuine items are in most 



cases absolutely even. 



Most of the surfaces of extant armour pieces cannot be considered as genuine. Iron based 



material is prone to corrosion. Repeated cleaning, in the time of use and conservation, had 



altered the original condition. Original coatings – interiorly and exterior ly – and shallow, 



recessed decorative drawings were often simply polished off throughout the ages. Today, a 



very close look is necessary to detect the remains of former decorations or coatings.  



Not only the exterior, but also the interior surfaces deliver information on the object. In the 



following the significances of both will be described in detail.
S. 85–86 · Sprachlich überarbeitet · Entwurf

4.1.4.2.1.1 Rough and blackened finishes

After forming was complete, the plate surface bore hammer marks and hammer scale.92 Not every object was sold polished: fifteenth-century documents distinguish between “white”, meaning polished, and “black”, meaning left rough from the hammer, armour. A Viennese will of 1460, for example, records:

[…] zwen eisenhuet, swarz und weiss […] doch nim ich meinem weib aus



den pesten eisenhut […] sol meiner hausfraun pei dem haus beleiben
Viennese will, 1460; see note 93.

The “best” helmet was most likely the polished one.93 Only a few surviving objects may have been sold rough from the hammer. Their outer surfaces were probably at least coated with oil and heated, producing a black layer that both inhibited corrosion and gave an even colour. Several late fifteenth-century helmets were probably never polished [ref_arm_1859] PDF; some retain coloured paint [ref_arm_1758] PDF [ref_arm_1893] PDF. Conversely, repeated cleaning may have turned formerly “black” objects “white” [ref_arm_1796] PDF. Apart from helmets, no fifteenth-century armour appears to have been sold black. Rough, blackened finishes became more common in the early sixteenth century, and most seventeenth-century armour was blackened.

It is now difficult to establish whether a black surface dates from manufacture or was applied later. In many cases, an apparent blackened finish is modern paint—possibly on [ref_arm_2114] PDF—or a rust converter such as tannin applied directly to corrosion products, as on [ref_arm_2013] PDF and the other objects in Athens.

Originalwortlaut vergleichen
4.1.4.2.1.1 “Rough” and blackened 



After all deformation work was finished, the surface of the armour plate was covered with 



hammer-marks and hammer scale92. Obviously, not all items were sold polished: 15th century



sources do differ between “white” (i. e. polished) and “black” (i. e. rough from the hammer) 



armour. For example, a Viennese will from the year 1460 names:  



[…] zwen eisenhuet, swarz und weiss […] doch nim ich meinem weib aus 



den pesten eisenhut […] sol meiner hausfraun pei dem haus beleiben93 



The “best” helmet was most likely the polished one. Only few existing items might have 



been sold “rough” from the hammer. Most likely their outer surface has at least got painted 



with oil and heated. The revealed black layer would prevent the item from corrosion and 



provide for a uniform color. A few helmets of the late 15 th century were most likely never 



polished [ ref_arm_1859]; some of them still retain colorful painting [ ref_arm_1758] 



[ref_arm_1893]. Some formerly “black” items might have been made “white” b y the 



cleaning throughout the ages [ ref_arm_1796]. With the exception of helmets, no armour 



parts of the 15 th century seem to have been sold “black”. From the early 16 th century on it 



became more common to leave the surface “rough” and “black”. In the 17th century, most of 



the produced armour got blackened.  



Today, it is very difficult to tell if a black surface is of the production time or maybe applied 



later. In many cases, what appears to be a blackened s urface is actually a modern paint 



(maybe [ref_arm_2114]) or a rust-converter (e. g. tannin) applied directly onto the corrosion 



products (e. g. [ref_arm_2013] and all other items in Athens).
S. 86–87 · Sprachlich überarbeitet · Entwurf

4.1.4.2.1.2 Polished finishes

Most objects were ground and polished over their entire outer surfaces. Some may subsequently have been blackened by the method described above. Certain objects were clearly polished before blackening [ref_arm_2348] PDF, although that treatment may have been applied later, during the sixteenth or seventeenth century [ref_arm_3333] PDF.

An unfinished early sixteenth-century suit of costume armour in Vienna [ref_ill_art_5382] PDF preserves the stage after forming but before grinding. Its hammer work is so fine that little material would have needed to be removed to create smooth surfaces. By the mid-sixteenth century, a particular style of infantry armour combined polished areas with rough, blackened ones: “black-and-white armour” [ref_ill_art_5363] PDF (description 2).

Documents up to the early sixteenth century refer to “filing” when describing the finishing of armour.94 Several tools and techniques could be used, including sandstone and files. Sandstone could be shaped into a large wheel powered by a person, horse, mule or waterwheel. Some work was probably done with large files. In the fifteenth century, final polishing was probably still carried out by hand at a polishing bench [ref_ill_art_5313] PDF [ref_ill_art_5326] PDF [ref_ill_art_5316] PDF [ref_ill_art_5318] PDF. Water power must also have been used for finishing from at least the second half of that century [ref_ill_art_5322] PDF.

The earliest reference I have found to an armour-polishing mill dates to 1483, when a citizen of Innsbruck sold a polishing mill and smelting works in Mühlau, probably established by the armourer Christian Spor.95 Water-powered wheels and a gripper to hold the workpiece, keeping the heated metal away from the fingers, would have made grinding considerably easier [ref_ill_art_5340] PDF. Specialist polishing workshops and equipment developed during the sixteenth and seventeenth centuries to support mass production [ref_ill_art_5339] PDF.

Works of art [ref_ill_art_5354] PDF (description 1) and surviving surfaces indicate that armour could be polished to a chrome-like brilliance. When the forehead reinforcement of [ref_arm_1802] PDF was removed for restoration in the late 1970s or early 1980s, it revealed an original mirror-polished surface beneath.

Originalwortlaut vergleichen
4.1.4.2.1.2 Polished 



The largest number of objects had been ground and polished at all outer surfaces. Some 



might have been subsequently “blackened” by the aforesaid method. Some items were 



obviously first polished and then blackened [ref_arm_2348], but maybe at a later time in the 



16th or 17 th century [ref_arm_3333]. In Vienna, an early 16 th century, unfinished suit of 



costume-armour is preserved [ ref_ill_art_5382]. It still shows the stage of work when the 



forming was finished, but had still to be ground. It is noteworthy that the hammer -work is 



so fine that not much material would have to be ground off to reveal plane surfaces. By the 



mid-16th century, infantry armour of a certain style showed both, partly polished and partly 



rough/blackened surfaces (black and white armour) [ref_ill_art_5363] (descr. 2). 



The sources – until the early 16 th century – speak of “filing” when the finishing of armour 



parts is concerned.94 The grinding of the plate can be done by different tools and techniques. 



Sandstone or files can serve this purpose. The sandstone could be cut into a huge wheel, 



which is either powered by a man, by a horse, a mule or by a water wheel. Probably some 



of the grinding work was achieved with large files. T he finish in the 15 th century was 



probably still made by hand on a polishing -bench [ ref_ill_art_5313] [ ref_ill_art_5326] 



[ref_ill_art_5316] [ref_ill_art_5318]. At least from the second half of the 15 th century on 



also water power must have been used for finishing the products [ref_ill_art_5322]. The first 



mention of an armour polishing-mill found by the author derives from the year 1483, when 



a citizen of Innsbruck sells a polishing-mill and a smeltery in Mühlau, probably once build 



by the armourer Christian Spor. 95 With the help of water powered wheels and a gripper to 



hold the work-pieces in place – and the hot piece away from the fingers – the grinding might



have been eased  immensely [ref_ill_art_5340]. In the 16 th and 17 th century, for the mass 



production of armour professional polishing workshops and devices were developed 



[ref_ill_art_5339]. 



Works of art [ ref_ill_art_5354] (descr. 1) and even surviving armour pieces indicate that 



armour generally could have been polished to chrome like appearance. When in the late 



1970ies or early 1980ies the forehead reinforce of the helmet [ref_arm_1802] was detached 



for restoration, underneath a mirror-like polished genuine surface came to light.
S. 87 · Sprachlich überarbeitet · Entwurf

4.1.4.2.1.3 Blueing

Blueing is probably a very old finishing technique. Heating a bright metal surface uniformly to approximately 280–320°C in air produces a lustrous blue oxide layer. Achieving even heating is the principal difficulty; immersion in a heated liquid or placement in heated sand can provide it.

Contrasting blue and “white” ornament can be produced by removing selected areas of this thin oxide layer through etching. The areas intended to remain blue are protected with a resist coating, while exposed areas are treated with weak acetic acid. The resist is then removed.96 The earliest surviving armour with etched blue decoration is Friedrich III’s horse armour of 1477, HJRK A 69.97 Many objects may once have been blued, but the extremely thin oxide layer could easily have been removed by repeated polishing over the centuries.

Originalwortlaut vergleichen
4.1.4.2.1.3 Blueing 



Blueing is probably a very old technique of surface -finishing. It is very simple to turn the 



silver-shiny color of the plate -surface into blue. The plate only needs to be heated all -over 



to 280-320 0C in a normal room-atmosphere reveal a shiny blue oxide layer on the surface. 



The most challenging part of this process is the uniform heating, which can be achieved by 



placing the object in a heated liqui d or in heated sand. For a contrast -ornamentation of 



“white” and blue areas, this thin oxide-layer can be taken off by etching. The blue segments 



need to be covered by a special paint and the uncovered regions are treated with a weak 



acetic acid. The paint  is subsequently wiped off the blue surface. 96 The oldest extant blue -



etched armour is Friedrich III.’s horse armour of 1477 (HJRK A 69). 97 It is possible that 



many armour parts once were blued, but as the blue oxide-layer is very thin, it got polished 



off throughout the ages.
S. 87–88 · Sprachlich überarbeitet · Entwurf

4.1.4.2.1.4 Gilding and silvering

Gilding and silvering can be applied only to polished surfaces. Documentary evidence from German-speaking regions dates back to 1445. A payment list for work commissioned by Duke Albrecht VI of Austria records:

[…] dem platner 19 ducaten; daz silber auf der platen hat funf markh



und drei gulden auf ain markh zu vergolden und zwen gulden von dem



markch zu lon […]
Payment record, 1445; see note 98.

It is unclear whether the armourer gilded the plate itself or only applied ornaments, but the wording suggests that at least the silver was applied directly to the plate.98

A document of 1460 is similarly imprecise but also records the gilding of at least part of an armour:

So hab ich geben in presencia herrn Hilbranden Fuchs Micheln,



goltschmid, zu dem harnasch gen Schottennland zu vergulden, geben 10



ducaten und 4 r. gulden.
Payment record, 1460; see note 99.

Some armour belonging to Emperor Friedrich III or his son Maximilian was partly gilded:99

1465 Juli 10. Hab ich auf gescheft meins gnedigen herrn, aber des



jungen chaisers harnasch zu vergulden, per Hainrichen von Freyberg



hofmaister geben 6 ducaten.
Payment record, 10 July 1465; see note 100.

No silvered armour object dating from before 1500 is known.100 The earliest gilded helmet is made of copper [ref_arm_1414] PDF. The helmet [ref_arm_1855] PDF preserves exceptionally fine etched decoration beneath gilding subsequently applied over its entire skull.

The technique of gilding ornamental patterns against a blue ground was most probably developed shortly before 1500. One of the earliest depictions is an Italian painting from approximately the last decade of the fifteenth century [ref_ill_art_5186] PDF. The helmet [ref_arm_1924] PDF retains traces of gilding in its etched ornament. The sides of its skull are undecorated but were probably blued to contrast with the gilded areas.

Redaktionelle Hinweise · 1
  • Die historischen Zitate bleiben unverändert; ihre schon in der Dissertation enthaltenen Übersetzungen stehen in den Fußnoten. Die Übersetzung von Anm. 99 scheint Personennamen anders zu gliedern als das deutsche Zitat. Vor einer neuen Übersetzung am historischen Beleg prüfen.
Originalwortlaut vergleichen
4.1.4.2.1.4 Gilding and silvering 



Only polished surfaces can be gilded or silvered. Documentary evidence for the silvering 



and gilding of armour in the German speaking lands is found already by 1445. A list of 



payments for works ordered by Duke Albrecht VI. of Austria notes the following:  



[…] dem platner 19 ducaten; daz silber auf der platen hat funf markh 



und drei gulden auf ain markh zu vergolden und zwen gulden von dem 



markch zu lon […]98 



It is unclear whether the armourer directly gilded the plate or just some applications, but the 



text suggests that at least the silver has been applied directly to the plate. 



Another document of 1460 is similarly imprecise, but it is also telling that at least parts of 



plate-armour had been gilded: 



So hab ich geben in presencia herrn Hilbranden Fuchs Micheln, 



goltschmid, zu dem harnasch gen Schottennland zu vergulden, geben 10 



ducaten und 4 r . gulden.99 



Some armour of Emperor Friedrich III. or his son Maximilian was partly gilded:



1465 Juli 10. Hab ich auf gescheft meins gnedigen herrn, aber des 



jungen chaisers harnasch zu vergulden, per Hainrichen von Freyberg 



hofmaister geben 6 ducaten.100 



No silvered armour part from before 1500 is known. The earliest gilded helmet is made of 



copper [ ref_arm_1414]. An extraordinarily well preserved, etched decoration on a 



subsequently entirely gilded skull is found at the helmet [ref_arm_1855].  



The techni que of ornamental pattern -gilding on a blue surface has most likely been 



developed shortly before 1500. One of the earliest illustrations is an Italian painting from 



about the last decade of the 15th century [ref_ill_art_5186]. The helmet [ref_arm_1924] still 



retains some gilding where the surface is decorated by ornamental etching. The sides of the 



skull are not decorated, but they were probably blued to contrast the golden areas.
S. 88 · Sprachlich überarbeitet · Entwurf

4.1.4.2.1.5 Etching

Italian armourers most probably introduced deep-etched decoration. The earliest etched breastplate dates from the 1480s [ref_arm_3736] PDF. Only one etched pair of hand defences probably made in German-speaking regions before 1500 survives [ref_arm_1136] PDF. Its etching was most likely added in the sixteenth century to match the pieces to other objects in a composite suit of armour.

Originalwortlaut vergleichen
4.1.4.2.1.5 Etching 



It was most likely the Italian armourers that first decorated their products with deep-etching. 



The oldest etched breastplate dates from the 1480ies [ref_arm_3736]. Only one etched pair 



of hand -protections, most likely made in the German speaking lands before 1500 exists 



[ref_arm_1136]. Most likely the etchings were applied secondarily in the 16 th century, to 



match the hand-protections to other armour parts of a composite suit of armour.
S. 88 · Sprachlich überarbeitet · Entwurf

4.1.4.2.1.6 Tinning

Exterior tin coatings are very rare on surviving armour. The only examples known to me are [ref_arm_1399] PDF and [ref_arm_1471] PDF. Tin is soft and can easily be scratched or polished away. Even when polished, it is less brilliant than polished steel, suggesting that its main purpose was protection against corrosion.

Tinning iron is a simple process. The ground surface is first etched to remove corrosion products and other oxides. It is then covered with a protective flux, such as animal fat or natural resin, and heated. Rubbing a tin bar across the hot surface melts the tin into a continuous coating.

Redaktionelle Hinweise · 1
  • „Natural-raisin“ als offensichtlichen Schreibfehler zu „natural resin“ korrigiert; keine Änderung der genannten Stoffgruppe.
Originalwortlaut vergleichen
4.1.4.2.1.6 Tinning 



Exteriorly, only very rarely a tin coating is found on extant armour. The only items known 



to the author are [ ref_arm_1399] and [ref_arm_1471]. Tin is a soft metal that can easily be 



polished or scratched off the plate-surface. It is also – even when polished – never as shiny 



as a polished steel plate. It is therefore very likely that the tin-coating of armour was merely 



intended to prevent the plate from corrosion. The technique of tinning iron is simple. The 



ground surface first needs to be etched to be free of corrosion products or other oxide layers. 



Then it is covered with an anti -oxidizing layer like animal -fat or natural -raisin and 



subsequently heated. A bar of tin is wiped over the surface and the melted tin will form a 



covering layer on the plate.
S. 88 · Sprachlich überarbeitet · Entwurf

4.1.4.2.1.7 Painting

Some armour was decorated with paint. The earliest object is a Type II helmet [ref_arm_1481] PDF, although its paint may have been applied in the sixteenth or seventeenth century. A Type VIII helmet [ref_arm_1635] PDF has alternating dark and light stripes. Several Type VII helmets made in German-speaking regions and left rough from the hammer were also painted [ref_arm_1741] PDF [ref_arm_1758] PDF [ref_arm_1882] PDF [ref_arm_1883] PDF [ref_arm_1893] PDF.

The breastplate [ref_arm_3684] PDF received its black-and-white painted areas in the mid-sixteenth century, while still in use, to imitate contemporary black-and-white armour.

Originalwortlaut vergleichen
4.1.4.2.1.7 Painting 



Some armour has been decoratively painted. The earl iest example is a helmet of type -II 



[ref_arm_1481], but it is possible that the painting was applied in the 16th or 17th century. A 



helmet of type-VIII [ref_arm_1635] is painted with alternating dark and bright stripes. A few 



helmets of type-VII, made in the German speaking lands and left “rough” from the hammer, 



were also painted [ ref_arm_1741] [ ref_arm_1758] [ ref_arm_1882] [ ref_arm_1883] 



[ref_arm_1893]. The black and the white areas on the breastplate [ref_arm_3684] have been 



painted in the mid-16th century when the plate was still in use – to imitate the contemporary 



black-and-white armour.
S. 88–89 · Sprachlich überarbeitet · Entwurf

4.1.4.2.1.8 Engraving, chiselling and filing

Surface ornament can also be applied mechanically. Fairly straight lines are easily filed, while more tightly curving lines can be incised with engraving needles. Repeated motifs or symbols can be stamped with specially shaped chisels [ref_arm_3197] PDF [ref_arm_1245] PDF. An image or inscription may consist of hundreds of small dots made with a pointed chisel [ref_arm_621] PDF [ref_arm_3062] PDF.101 All these techniques have been used since antiquity and are the earliest decorative methods found on surviving armour.

In complex designs, it can be difficult to distinguish a chiselled line from an etched one. A lens or microscope may help: etched lines have irregular, burred-looking margins, while the ends of engraved lines form narrow curves. By the end of the fifteenth century, expensive German armour often carried mechanically incised lines and inscriptions [ref_arm_3363] PDF. Etching replaced these older methods in the early sixteenth century.

Redaktionelle Hinweise · 1
  • „Lean-bow“ im Original wurde als schmal gebogener Linienabschluss wiedergegeben. Die genaue diagnostische Form sowie die Aussage zu „burred“ geätzten Rändern fachlich prüfen; keine mikroskopische Neubewertung vorgenommen.
Originalwortlaut vergleichen
4.1.4.2.1.8 Engraving, chiseling, filing 



Surface ornamentations can be applied mechanically. More or less straight lines can easily 



be filed; more narrowly winding lines can be engraved with etcher’s -needles. Repeated 



patterns or symbols can be stamped with especially shaped chisels [ ref_arm_3197] 



[ref_arm_1245]. A drawing or an inscription could consist of hundreds of small dots applied



by a pointed chisel [ ref_arm_621] [ref_arm_3062]101. All these techniques are in use since 



antiquity and therefore they are also the oldest decorating-techniques found on extant armour 



pieces. In some complex drawings it is difficult to tell a chiseled line from an etched line. A 



closer look through a lens or a microscope might help. The edges of an etched line appear 



burred and the endings of an engraved line have the shape of a lean -bow. By the end of the 



15th century, the costly German armour was often decorated with mechanically applied 



decorative lines and inscriptions [ ref_arm_3363], until in the early 16 th century the etching 



techniques replaced the older methods.
S. 89 · Sprachlich überarbeitet · Entwurf

4.1.4.2.2 Interior surfaces

Interior surfaces normally face the wearer’s body and retain the closest approximation to the armour’s original worked surface. No armour object was ground on the inside; before grinding and polishing, the exterior must have looked similar. Hammer marks and often layers of hammer scale remain visible inside. Nevertheless, repeated removal of corrosion means that most interiors no longer preserve their exact condition at manufacture.

Perspiration and condensation increased the risk of internal corrosion. Surprisingly few objects nevertheless retain an interior coating. Some were certainly tinned during manufacture. The coating inside the late fourteenth-century breastplate [ref_arm_3698] PDF, for example, cannot be a later addition because its original velvet covering survives. Small plates from segmented torso protection are often tinned [ref_arm_3885] PDF.

The bright red or orange paint inside many objects [ref_arm_3638] PDF [ref_arm_1352] PDF [ref_arm_2039] PDF is characteristic of Luigi Marzoli’s collection in Brescia and was probably applied by one of his restorers in the twentieth century. The paint on the leg protection [ref_arm_2843] PDF may also be modern.

Originalwortlaut vergleichen
4.1.4.2.2 Inner surfaces 



Interior surfaces of armour are regularly those that are facing the wearer’s body. They 



resemble the most original surface of armour. No single piece of armour is ground interiorly. 



The outer surface must have looked similar before i ts grinding and polishing. Interiorly, 



hammer-marks are visible and often layers of hammer -scale. As these surfaces were often 



cleaned from corrosion, most of them cannot be considered as showing the state of the 



production time. Body sweat and condensing water increased a potential corrosion -risk of 



the interior surfaces. Despite this fact, surprisingly few items show an interior coating. Some 



armour was originally certainly tinned. For example the interior coating of the late 14 th 



century breastplate [ref_arm_3698] cannot have been applied in later times, as the item still 



retains its original velvet -cover. Often the small plates of segmented torso -protections are 



tinned [ref_arm_3885]. The bright red or orange color found inside many extant armour parts 



[ref_arm_3638] [ref_arm_1352] [ref_arm_2039] are significant for the collection of Luigi 



Marzoli in Brescia – probably one of his restorers applied them in the 20th century. Possibly 



also modern is the paint at the leg armour [ref_arm_2843].
S. 89 · Sprachlich überarbeitet · Entwurf

4.2 Joints, fastenings and applied elements

Once the plates had been shaped and polished, the individual elements had to be joined and fitted with fastenings and other applied features. Many of these components are now missing, so most objects would no longer function in their present display or storage condition. Understanding their former operation and appearance requires a classification of the surviving evidence for joints, fastenings and non-structural attachments. These important features have not previously been the focus of a dedicated study.

Originalwortlaut vergleichen
4.2 Joints and applications 



After the armourer had finished the general shaping and polishing of the plates, the single 



armour parts needed to be joined together and to be fitted with fastening systems and 



applications. Most armour  parts would not function anymore in the condition they are 



currently displayed or stored, as many of these features are lost today. For the understanding 



of the former function and appearance of a certain item, it is indispensable to classify all the 



data on joints, fastenings and non -constructive applications found on extant armour parts. 



No study has ever focused on such important aspects.
S. 89–91 · Sprachlich überarbeitet · Entwurf

4.2.1 Rivets

A rivet can be described as a short metal rod with two expanded, mushroom-like ends. It primarily serves either to join two elements permanently or to decorate an object; in some cases, it performs both functions.

Riveting is among the oldest techniques for assembling metal components. Only lacing may be older. For example, the hilts of eleventh-century BC Celtic brass swords were riveted to their blades.102 Hellenistic brass helmets often retain rivets that probably once secured a lining.103

Historically, a rivet was simply called a “nail”104 or, in German, “Nagel”,105 probably because it served the same purpose: fastening components together. Whereas handmade nail heads were roughly shaped with a few hammer blows, the primary heads of rivets were generally formed with a die or by embossing. Like nails, armour rivets are solid and have one preformed head, made before installation. The rivet is then closed with a hammer to secure the components. A small plate washer may first be placed over the shank to enlarge the bearing area of the smaller, newly formed closing head and prevent the rivet from pulling through.

Late medieval plate armour uses rivets in three basic ways. They may fasten components rigidly together, secure overlapping plates to textile or leather to permit limited articulation, or join plates directly while allowing them to pivot—or both pivot and slide—around the rivet.

Every object of plate armour has rivets, or holes indicating where lost rivets once stood. Rivets are wearing components, especially in articulated joints. They could be lost when the plates were stressed or when corrosion reduced their diameter enough to let them pass through the holes. Material defects could also cause their shanks to fracture. Maintenance required rivets to be replaced when damaged plates were removed or organic components renewed, both during use and later in collections. Rivets therefore provide important evidence for an object’s restoration history and authenticity. Certain features may indicate whether they were made by hand or machine.

There is no evidence that original rivets were shaped by material-removing processes such as filing or turning. These would have been unnecessarily expensive, and no corresponding tool marks are visible on rivets presumed to be original. Such marks could have been polished away, but occasional eccentricity between head and shank also argues against manufacture on a lathe. Iron rivets were certainly not cast: cast iron would be too brittle for hammering, quite apart from the difficulties of casting such small objects before the development of late nineteenth-century techniques. Contemporary images show nails being forged [ref_ill_art_5327] PDF, and there is no reason why rivets should have been made differently. All old structural armour rivets may therefore be presumed to have been forged.

A possible exception is the large flower-headed rivets securing the chin straps inside [ref_arm_2028] PDF. They were probably cast in copper alloy and gilded. The helmet was originally “white”, or polished. In the sixteenth or early seventeenth century, probably in Venice, it received a textile covering, now lost, and several gilded ornaments. Its nape guard was also lengthened with a pointed plate. Since the rivets lie beneath the other copper-alloy attachments, their heads were probably concealed by the textile and may predate the covering.

Rivets made entirely of copper alloy were used only to secure non-structural attachments. On the hand defence [ref_arm_1251] PDF, the brass rivets are demonstrably old: engraved and punched decoration continues uninterrupted across their flush heads and the copper-alloy bands they secure. The closely spaced dome-headed rivets around the cuff are also entirely of copper alloy.

No scholarly discussion or historical description of rivet manufacture could be found. Nineteenth-century descriptions of nail-making offer a substitute. The shared historical terminology also suggests that nails and rivets were made in the same workshops. Before considering manufacture, the different rivet forms found on late medieval armour must be distinguished.

Redaktionelle Hinweise · 2
  • „Celtic brass swords“ des Originals bleibt wörtlich als Material- und Kulturzuordnung erhalten; „bronze“ wurde nicht ohne Quellenprüfung eingesetzt. Ebenso steht „Hellenistic“ neben dem Hinweis auf Helme des 6. Jh. v. Chr. in Anm. 103.
  • Die pauschalen Aussagen zu massiven und geschmiedeten Nieten sind im Zusammenhang mit den anschließend beschriebenen hohlen Köpfen und Ausnahmen zu lesen.
Originalwortlaut vergleichen
4.2.1 Rivets 



A rivet is maybe best described as a metal wire with two mushroom-like widened ends. The 



main tasks of rivets  can either be to connect two segments of any material inseparably 



together or to bring a decorative highlight to a surface of any kind of artifact. In some cases, 



rivets fulfill both tasks together. 



Rivets are one of the oldest techniques for joining seve ral metal pieces to become one 



artifact. Only the lacing of metal parts might be older. For example the hilts of 11 th century



B.C. Celtic brass swords had already been riveted to the blade. 102 Hellenistic brass helmets 



often retain the rivets that once probably held some sort of lining.103 



The historical term for “rivet” has been simply “nail”104 or in German “Nagel”105, probably 



as it had the same purpose like a nail: fixing parts together. While th e heads of simple 



handmade nails were shaped roughly by a few blows of the hammer, the basic shape of the 



exterior rivet-heads is usually made by either some kind of die or by embossing. Just like 



nails, all armour -rivets are massive and have one “factory -head”, formed before the rivet 



was attached to armour. The rivets were “closed” with the help of a hammer, when parts had 



to be joined together. Sometimes small plate -washers (see below) were first stuck over the 



shank to enlarge the surface of the revealed smaller mounting-head and to prevent the rivet 



from falling out.  



On late medieval plate -armour, rivets are used for basically three different joining -



techniques. The first fixes the parts directly together in an invariable position. The two other 



techniques leave limited articulation to the single plates: In one case by riveting the 



overlapping plates to fabric or leather; in the second case by riveting them directly together 



but – depending on the desired flexibility – either loosely enough to pivot or both to pivot 



and to slide (see below). 



At each piece of plate armour rivets can be found. On items where all rivets are lost, the 



holes they left behind in the plate witness of their former existence. Rivets count to the 



wearing-parts of armour, at articu lated joints they are exposed to even more wear than on 



fixed-joints. They easily got lost when the plates were stressed or corrosion reduced their 



diameter so they would slip through the holes. Shanks may also got cracked, due to material-



defects. Maintenance work made it necessary to replace rivets. Broken plates needed to be 



taken off, old organic parts needed to be renewed – in times of use and in times of collection-



keeping. The examination of the rivets is very important for an insight of item’s restoration-



history, but also for the determination of its authenticity. Certain features might tell if they 



were made by hand or by machines.  



There is no evidence that rivets were formed by cutting techniques like filing or turning. Not 



only would this have been much too expensive, but also no traces of the necessary tools are 



visible at any presumably genuine rivet. Of course, these details might have got polished off, 



but for example the occasionally found eccentric position of shank and head contradicts the 



idea of their making by turning. Certainly, rivets were not cast, as rivets made of cast -iron 



would be too brittle when being hammered, not to mention the difficulties of casting such 



small iron objects before the techniques developed in the late 19 th century. Furthermore, 



according to contemporary artworks, nails were usually forged [ref_ill_art_5327] and there 



is no reason why rivets should not have been produced by the same technique. Therefore, it



can be presumed that all old constructional rivets on armour were forged. The only exception 



found, might be the rivets with large floral heads for the interior attachment of the chin straps 



at the helmet [ref_arm_2028]. Most likely they were cast from copper alloy and gilded. This 



helmet was originally “white”, i. e. polished. In the 16 th or early 17 th century, probably in 



V enice, it got covered by fabric (cover not extant) and several gilded d ecorations were 



attached. Also the nape -guard was extended by the attachment of a pointed plate. As the 



aforesaid rivets lay underneath the other copper alloy applications, the rivet heads were 



probably covered by the fabric. Therefore, they possibly deriv e from the time before the 



attachment of the cover.  



Only rivets for the fixation of non-constructional applications were made entirely of copper 



alloy. At the hand-protection [ref_arm_1251] it becomes clea r that the brass rivets are old, 



as the engraved and punched surface decoration of the attached copper alloy bands is not 



interrupted at the leveled rivet-heads. Also the narrow row of dome-headed rivets at the edge 



of the cuff is entirely made of copper alloy. 



No scientific discussion of historical rivet-making seems to exist. It was also not possible to 



find a historical description of the manufacture of rivets. As a replacement, 19 th comments 



on the making of nails may serve. It can be presumed that – also due to the identical historical 



terms – rivets and nails were made by the same workshops.  



Different shapes of rivets occur on late medieval armour. Before entering the discussion of 



their making, the different types will be introduced.
S. 91 · Sprachlich überarbeitet · Entwurf

4.2.1.1 Type a: a broad, flat head

[ref_ill_riv_a] Type a occurs on all kinds of armour. Its principal use is to secure internal leather straps in articulated lame assemblies.106 The broad, flat head prevents the leather from pulling over it under tension. It normally lies inside, where its low profile does not press uncomfortably against the wearer.

On Italian armour, the preformed head sometimes lies outside, for example when securing straps or buckle plates. Exposed heads often carry simple radial lines cut with a chisel or file [ref_arm_88] PDF. Rivets of this kind were reproduced during restoration of the suit [ref_arm_5110] PDF, for example on [ref_arm_3880] PDF.

Armour probably made in Maximilian I’s workshop at Arbois has rivets with ornamentally stamped exterior heads [ref_arm_3855] PDF [ref_arm_3823] PDF [ref_arm_1973] PDF [ref_arm_3570] PDF. The same forms occur on Type VI [ref_arm_1935] PDF and Type VII helmets [ref_arm_1744] PDF [ref_arm_2088] PDF [ref_arm_1751] PDF [ref_arm_1754] PDF attributed to Italian manufacture. Stamped Type a rivets also attach the finger plate on [ref_arm_1290] PDF.

Decorated Type a rivets appear to have been reproduced in modern times, since examples on [ref_arm_3287] PDF secure modern leather. An old repair to [ref_arm_2148] PDF uses two Type a rivets with their heads inside, one stamped and the other filed. A unique ornament of four stamped blossoms appears on the rivets of [ref_arm_3698] PDF.

Originalwortlaut vergleichen
4.2.1.1 Type-a [ref_ill_riv_a] 



This rivet-type is found at armour parts of all types. It mainly106 serves for fixing the interior 



leather on constructional lame-joints. The large, flat head prevents the leather from slipping 



over the rivet-head when stressed. The rivet -head is usually positioned interiorly so its flat 



appearance does not bother the wearer. On armour of Italian production, rivets of type -a 



sometimes also have their factory-heads exteriorly, e. g. for fixing leather straps or the holder 



plates of buckles. In these cases the rivet -heads are often decorated by simple chiseled or 



filed radial lines (e. g. [ref_arm_88]). Such rivets were reproduced for the restoration of the 



suit [ref_arm_5110] (e. g. [ref_arm_3880]). On armour probably coming from Maximillian 



I.’s armourer’s workshop in Arbois rivets with ornamentally-stamped exterior heads have 



been used (e. g. [ ref_arm_3855] [ ref_arm_3823] [ ref_arm_1973] [ ref_arm_3570]). The 



same rivets are found at helmets of type-VI [ref_arm_1935] and type-VII [ref_arm_1744] 



[ref_arm_2088] [ref_arm_1751] [ref_arm_1754], all attributed to Italian making. Also for 



the attachment of the plate protecting the fingers at the item [ref_arm_1290], stamped rivets 



of type-a were used. It seems like decorated type -a rivets had been reproduced in modern 



times, as they hold the modern leather at the item [ref_arm_3287]. For an old repairing, two 



type-a rivets, one decorated by stamping and the other one by filing, were used with their 



head interiorly at the helmet [ ref_arm_2148]. A very unique decoration – four stamped 



blossoms – is found at the rivets of the breastplate [ref_arm_3698].
S. 91–93 · Sprachlich überarbeitet · Entwurf

4.2.1.2 Type b: a hemispherical head

[ref_ill_riv_b] Type b has a hemispherical head, usually placed outside. It is the most common rivet form and occurs on every kind of armour and joint.

When structural rivets were intended to appear yellow, a brass cap was soldered over an iron head. Such rivets were reserved for expensive armour. Where the thin copper-alloy cap has worn away, the underlying tin solder is often visible [ref_arm_1645] PDF. Representative examples with apparently original caps of different diameters include [ref_arm_1721] PDF [ref_arm_1245] PDF [ref_arm_1360] PDF [ref_arm_1063] PDF [ref_arm_2057] PDF [ref_arm_3084] PDF.

Solid copper-alloy Type b rivets on some objects are clearly modern [ref_arm_1747] PDF [ref_arm_1062] PDF. They have thick shanks and are often accompanied by modern, uniformly round washers [ref_arm_3322] PDF. Such rivets are particularly common on reproduction suits from the late nineteenth and early twentieth centuries [ref_arm_3213] PDF.

Some iron Type b rivets are also clearly modern. In the early twentieth century, numerous objects now in the MET were fitted with decoratively stamped heads. Stuart Pyhrr records that Bashford Dean assembled composite suits for his private collection before they entered the museum.107 Apparently on Dean’s instructions, the Type b rivets of newly assembled and completed “Gothic” suits were replaced with lion-head or blossom-stamped examples to give them a uniform appearance. The suit [ref_arm_4091] PDF provides one example; see individual objects [ref_arm_1682] PDF [ref_arm_2337] PDF. The suit [ref_arm_3235] PDF instead received spiral-headed rivets throughout; see [ref_arm_131] PDF [ref_arm_1681] PDF. The rivets on [ref_arm_1816] PDF and the chin-and-throat defence [ref_arm_3128] PDF probably date from the same period.

Blossom-stamped heads of the same form—called “a bozetta” by Scalini108—also occur on helmets in the MDA [ref_arm_2150] PDF, MLM [ref_arm_2027] PDF and MNMC [ref_arm_1839] PDF. On the latter two, they are unlikely to be original because they secure new leather.109 On several SMM breastplates in Munich, however, they are probably old [ref_arm_3655] PDF [ref_arm_3656] PDF [ref_arm_3657] PDF [ref_arm_3661] PDF [ref_arm_3663] PDF [ref_arm_3664] PDF [ref_arm_3665] PDF [ref_arm_3666] PDF [ref_arm_3667] PDF [ref_arm_3699] PDF. A further comparable breastplate from the Munich Zeughaus is now in an unidentified collection [ref_arm_4079] PDF.

A drawing of one of the breastplates dating to about 1866 already shows a blossom-headed rivet, although enlarged and without much detail.110 The rivets on these breastplates are more irregular than those on the helmets and have a stylised beaded ring around the base of the head. Wackernagel states, without a specific reference,111 that similar rivets occur on armour attributed to Brescian workshops.112 He probably meant two nearly identical Type V helmets [ref_arm_2113] PDF [ref_arm_2124] PDF, both attributed to a Brescian maker.

These helmets, together with [ref_arm_5109] PDF, may support his suggestion. Their rivets show obvious wear, unlike those on Dean’s restored objects. On [ref_arm_2113] PDF, they still hold part of the textile lining and may therefore date from the period of use. One of these helmets may have supplied the model for the reproduced heads.

The MET’s Type VII helmet [ref_arm_1819] PDF, in the so-called Franco-Burgundian style and reportedly found in a French river,113 also has blossom-headed rivets. Early photographs, apparently taken before restoration, suggest that they are original. A painting likewise shows a pointed helmet with blossom-headed rivets [ref_ill_art_5243] PDF. Their exclusive association with Brescia is doubtful, since only the first two helmets can actually be located there. The extensive trade in rivets discussed by Scalini supports their use beyond Brescian workshops.

The lames of [ref_arm_1128] PDF are also joined with blossom-headed rivets. These differ slightly from the preceding examples and may be original.

A unique Type b variant occurs on the suit [ref_arm_3256] PDF; see individual objects [ref_arm_866] PDF [ref_arm_3926] PDF. Its very large, low, gilded heads are plainly decorative but also structural. Damage exposes smaller iron rivet heads beneath. Where the gilding has worn away, the broad domed surfaces reveal a silvery material. Fractures and surface defects suggest that a material both soft and brittle, possibly a tin–lead alloy, surrounds the iron heads. These coverings may have been cast directly around the heads or made separately. Their dots and lines were punched and engraved, and the surface was probably covered with gold foil.

Redaktionelle Hinweise · 2
  • „Brazed … by means of tin-solder“ wurde wegen des ausdrücklich genannten Zinnlots als „soldered“ formuliert. Die abweichende Hartlötannahme für andere Verbindungen bleibt getrennt erhalten.
  • Schreibweise „a bozetta“ im Haupttext und „a bozzetta“ im zitierten Fußnotentext unverändert beibehalten.
Originalwortlaut vergleichen
4.2.1.2 Type-b [ref_ill_riv_b] 



A type-b rivet has a hemispherical head, frequently placed exteriorly. This is the most 



common rivet-type and it is found at any type of armour and at any type of joint.



Where constructional rivets should appear yellowish, a brass c ap was brazed to the head of 



an iron rivet. Only expensive armour was equipped with such rivets and it would be too 



much to quote all the items that reveal such rivets. In many cases where the thin copper alloy 



plate is rubbed off, the tin-solder underneath is visible [ref_arm_1645]. As pars pro toto some 



examples with apparently genuine capped -rivets with varying head -diameters will be 



quoted: [ ref_arm_1721] [ref_arm_1245] [ref_arm_1360] [ ref_arm_1063] [ ref_arm_2057] 



[ref_arm_3084]. The massive copper alloy rivets of type-b found on some objects are clearly 



modern [ ref_arm_1747] [ref_arm_1062]. Their shank is thick in diameter and often also 



modern regular round washers are used at the joints [ref_arm_3322]. Especially reproduced 



suits of the late 19th and early 20th century contain such rivets [ref_arm_3213]. 



Also some types of iron type -b rivets are clearly modern: At some time in the early 20ieth 



century a large number of objects now in the MET were equipped with ty pe-b rivets with 



decoratively stamped heads. Stuart Pyhrr quotes that it was Bashford Dean who assembled 



the different composite suits of armour for his private collection before they came to the 



MET.107 To give the newly composed and completed “gothic” suit s a somewhat uniform 



appearance for example at [ref_arm_4091] (for details see the single items [ref_arm_1682] 



[ref_arm_2337]) all rivets of type-b – apparently on Dean’s order – were replaced by others, 



with either a stamped lion-head or a blossom. At the suit [ref_arm_3235] (for details see the 



single items [ref_arm_131] [ref_arm_1681]) only rivets with spiral -shaped heads were 



attached. The rivets at the helmet [ ref_arm_1816] and at the chin/throat protection 



[ref_arm_3128] are probably also productions from this time.  



Surprisingly, the same blossom -stamped rivet heads – Scalini calls them “a bozetta” 108 – 



found at some MET items are found at helmets in the MDA [ ref_arm_2150], the MLM 



[ref_arm_2027] or the MNMC [ref_arm_1839]. While it is unlikely that they are genuine at 



the two latter helmets 109 – they hold new leather interiorly – at a number of Munich SMM 



breastplates they are most likely old [ ref_arm_3655] [ref_arm_3656] [ ref_arm_3657] 



[ref_arm_3661] [ ref_arm_3663] [ ref_arm_3664] [ ref_arm_3665] [ ref_arm_3666] 



[ref_arm_3667] [ref_arm_3699]. A further similar breastplate from the Munich Zeughaus 



with such a rivet is now in an anonymous collection [ ref_arm_4079]. A drawing of one of 



the breastplates of about 1866 already shows a blossom -head rivet, although not very 



detailed and larger in scale.110 At these breastplates, the rivets look more irregular than those 



on the said helmets and additionally around the base of the head they have a stylized ring of



pearls. Wackernagel – without a reference 111 – quotes that similar rivets were attached to 



armour attributed to Brescian workshops. 112 What he probably meant are two almost 



identical helmets of type-V [ref_arm_2113] [ref_arm_2124]. They actually reveal such rivets 



and are attributed to a Brescian maker. These helmets, together with [ ref_arm_5109] can 



maybe help to proof Wackernagel’s suggestion. Their rivets differ from Dean’s restored 



objects by their obvious wear. At [ ref_arm_2113], interiorly a part of the lining fabric 



remains – held by these rivets. It is therefore possible that in this case they originate from 



the time of use. The model for the reproduced rivets was possibly designed by the samples 



on one of these helmets. There is a helmet of type-VII [ref_arm_1819] in the MET, designed 



in the so called “Franco -Burgundian style”, that is said to have been found in a river in 



France.113 Also here, the blossom -headed rivets are found. The old images – presumably 



showing the pre-restoration condition – indicate that the rivets are genuine. Also a painting 



shows a helmet with a pointed skull and rivets with a blossom -shaped head 



[ref_ill_art_5243]. It is questionable if these designs were exclusively used in Brescia, as the 



manufacture of only the two first mentioned helmets can actually be located in this city. The 



extensive trade of such rivets that Scalini referred to (see above), supports the theory that 



they were not only processed in Brescian workshops.  



The single lames of the hand -protection [ ref_arm_1128] are also joined by rivets with 



blossom-shaped heads. They are slightly different from those mentioned above and might 



be original.  



An absolutely unique version of type-b rivets is found at the suit [ref_arm_3256] (for details 



see the single items [ref_arm_866] [ref_arm_3926]). The very large and flat, gilded heads 



are clearly of decorative character, while t hey still have a constructional function. The 



damages at some of the heads show a smaller head of an iron rivet. Where the gold is rubbed 



off, at the large hemispherical heads a silver -shiny material is visible. Due to the defects 



where parts of the heads had broken off and where the surface is damaged by faults, it is 



likely that around the iron rivet -heads a material – both fragile and soft – is placed. This 



could well be a tin -lead alloy. Either these plates were cast around the iron rivet -heads or 



they were worked separately. The dot-and-line decorations are engraved and punched. The 



heads then were probably plated by gold foil.
S. 94 · Sprachlich überarbeitet · Entwurf

4.2.1.3 Type c: a pointed head

[ref_ill_riv_c] Type c is the rarest rivet form. Its head is essentially conical and, like that of Type b, lies outside. A few examples serve as visor pivots on Type VII helmets [ref_arm_1780] PDF [ref_arm_1847] PDF [ref_arm_1895] PDF [ref_arm_2094] PDF. They are more frequent in the same position on Type IV helmets with side-pivoting visors, usually with a tapered profile [ref_arm_1500] PDF [ref_arm_1529] PDF [ref_arm_1547] PDF [ref_arm_1559] PDF [ref_arm_1560] PDF [ref_arm_1596] PDF [ref_arm_1605] PDF.

Although the originality of many examples is uncertain, the unaltered excavated helmets [ref_arm_1520] PDF [ref_arm_1543] PDF confirm their historical use as Type IV visor pivots. Simple versions also secure the visors of apparently unrestored Type II helmets from Chalcis [ref_arm_1445] PDF [ref_arm_1449] PDF [ref_arm_1450] PDF [ref_arm_1451] PDF [ref_arm_1453] PDF [ref_arm_1454] PDF.

Two Type III helmets have Type c rivets. On [ref_arm_1418] PDF, the heads are exceptionally long, pointed and square in section, gilded and encircled near the base by two filed lines. Those on [ref_arm_4434] PDF are simple and round in section. The Type VI helmet [ref_arm_1944] PDF has pyramidal heads. Pointed rivets attach the unusual medial-ridge reinforcements of two Type V helmets [ref_arm_2075] PDF [ref_arm_2107] PDF. They also occur on two backplates [ref_arm_3340] PDF [ref_arm_3264] PDF and a breastplate [ref_arm_3426] PDF. Together, these examples show their use in Spain, Italy and German-speaking regions.

Originalwortlaut vergleichen
4.2.1.3 Type-c [ref_ill_riv_c] 



Type-c rivets are the rarest of all ty pes. Like type -b rivets, their main head is always 



exteriorly. The head is basically of the shape of a pointed cone. In few cases they serve as 



the pivot joints of visors on helmets of type -VII [ ref_arm_1780] [ ref_arm_1847] 



[ref_arm_1895] [ref_arm_2094]. In the same function, usually with a tapered profile, the y 



are often used on helmets of type -IV with a side pivoting visor [ ref_arm_1500] 



[ref_arm_1529] [ ref_arm_1547] [ ref_arm_1559] [ ref_arm_1560] [ ref_arm_1596] 



[ref_arm_1605]. While for many objects it cannot be said with certainty that these rivets are 



genuine, the archaeologically excavated and unaltered helmet s [ref_arm_1520] 



[ref_arm_1543] proof that they were actually used for the visor -pivots of helmets of type -



IV . Also at several of the apparently un -restored type-II helmets from Chalcis, the visors 



were attached by simple versions of this rivet [ ref_arm_1445] [ ref_arm_1449] 



[ref_arm_1450] [ref_arm_1451] [ref_arm_1453] [ref_arm_1454]. On two examples of type-



III helmets, rivets of type -c are attached. In one case, they are of square section 



[ref_arm_1418], exceptionally long and pointed, gilded and towards the bottom two 



encircling lines are filed. Simple round examples are attached to the item [ ref_arm_4434]. 



The type-VI helmet [ ref_arm_1944] is equipped with pointed rivets of a square section 



(pyramid). Two helmets of type-V have their uncommon medial-ridge reinforce attached by 



pointed rivets [ ref_arm_2075] [ ref_arm_2107]. Two backplates [ ref_arm_3340] 



[ref_arm_3264] and one breastplate [ref_arm_3426] are equipped with type-c rivets. These 



observations show that they were used in Spain, Italy and the German speaking lands.
S. 94 · Sprachlich überarbeitet · Entwurf

4.2.1.4 Type d: an embossed hollow head

[ref_ill_riv_d] Type d is probably the most elaborate rivet form. Technically derived from Type a, it has a much larger head embossed into a hemisphere. All examples are made in one piece. Some have plain domes [ref_arm_1727] PDF; others carry embossed ornament resembling blossoms [ref_arm_1718] PDF [ref_arm_1840] PDF [ref_arm_1858] PDF or spiral ridges [ref_arm_1704] PDF [ref_arm_1735] PDF [ref_arm_1837] PDF [ref_arm_1841] PDF [ref_arm_1843] PDF [ref_arm_1894] PDF. Not all examples on [ref_arm_1717] PDF [ref_arm_1720] PDF are probably original.

This form was used chiefly to attach linings and chin straps to Type VII helmets. One Type III helmet has flower-shaped iron examples [ref_arm_1383] PDF; another has similar heads in copper alloy [ref_arm_1398] PDF. The domed examples on [ref_arm_2094] PDF are unique in being made from a tin or lead alloy.

The dome-shaped copper-alloy ornaments on the breastplate [ref_arm_3734] PDF resemble rivet heads but are separate caps sewn to the textile to conceal washers. Beneath them, copper rivets and iron washers—now lost to corrosion—secured an exterior textile covering.

Originalwortlaut vergleichen
4.2.1.4 Type-d [ref_ill_riv_d] 



Rivets of type-d are probably the most elaborately worked types of all. They are technically 



based on type -a rivets, but the head is much larger and hemispherical embossed. All 



examples are made of one piece. Besides  simple dome-shaped examples [ ref_arm_1727], 



the head can be decorated by ornamental embossing. Some heads appear like blossoms 



[ref_arm_1718] [ref_arm_1840] [ref_arm_1858], while at others ridges are spirally winding 



around the head [ ref_arm_1704] [ ref_arm_1735] [ ref_arm_1837] [ ref_arm_1841] 



[ref_arm_1843] [ ref_arm_1894] (probably not all are genuine at [ ref_arm_1717] 



[ref_arm_1720]). This type of rivet has been u sed merely for the attachment of the lining 



and the chin-straps of type-VII-helmets. In only one case also a helmet of type-III is equipped 



with blossom shaped iron rivets of type -d [ref_arm_1383]. A second type-III helmet has 



similar rivets attached, but they are made of copper alloy [ ref_arm_1398]. Unique are the 



dome-headed examples on [ ref_arm_2094]: they are made of a tin or lead alloy. At the 



breastplate [ref_arm_3734], dome-shaped copper alloy applications that appear like rivet -



heads are visible. They are actually separate caps that were sown to the fabr ic to cover the 



washers. The copper rivets underneath, together with an iron washer (lost through corrosion) 



held an exterior fabric cover in place.
S. 94–95 · Sprachlich überarbeitet · Entwurf

4.2.1.5 Other forms

Some rivets cannot be assigned clearly to any of these groups. Particularly interesting is a flower-like head occurring in related variants at the visor pivots of many Type VII helmets.114 Their marks identify some of these helmets as reproductions [ref_arm_1857] PDF [ref_arm_1899] PDF.115 Three others are so similar in skull shape and other details that they probably came from a single workshop [ref_arm_1900] PDF [ref_arm_1773] PDF [ref_arm_1742] PDF.

Most have paired holes at ear level and on top of the skull for lacing in a lining. Many modern armourers appear to have favoured this feature, as further reproductions suggest [ref_arm_4600] PDF [ref_arm_4431] PDF [ref_arm_4448] PDF. Such holes are common on tournament helmets [ref_arm_1732] PDF, whereas the Type VII examples discussed here have forms characteristic of field armour.

Originalwortlaut vergleichen
4.2.1.5 Others 



There are also other rivet -types found on armour that cannot clearly be attributed to one 



group. Th e most interesting is a certain rivet -model – the head basically resembling a 



blossom. It appears in similar variations at the visor-pivots of many type-VII helmets114. Due 



to their marks, some of these helmets are certainly reproductions [ ref_arm_1857]



[ref_arm_1899]115. Others are so similar in the shape of the skull and other details that it is 



likely that all three were made in the same workshop [ ref_arm_1900] [ ref_arm_1773] 



[ref_arm_1742]. Most of the concerned helmets show pairs of holes at the level of the ears 



and at the top for the lacing of an interior lining. This feature seems to have been favored by 



many modern armourers, as many further reproductions suggest [ ref_arm_4600] 



[ref_arm_4431] [ ref_arm_4448]. The holes are rather common for tournament helmets 



[ref_arm_1732], but the design of the quoted type-VII head-pieces is typical for field use.
S. 95–97 · Sprachlich überarbeitet · Entwurf

4.2.1.6 Manufacturing rivets

A late medieval armourer was probably capable of making his own rivets. As a specialist whose time was valuable, however, he would have concentrated on shaping plates rather than producing large quantities of small components. Elaborate Type d rivets on other contemporary ironwork, including doors [ref_ill_art_5152] PDF, suggest a specialist trade. A sixteenth-century English account confirms that armourers bought rivets, like other semi-finished materials, from suppliers.116

Despite extensive research, I found no pre-industrial description of rivet manufacture.117 Rivets were nevertheless always mass-produced. In 1828, a Stirling nail-maker wagered that he could make 17,030 nails in two weeks and finished ahead of time. His normal output was 700 nails in a twelve-hour working day.118 The process was simple enough that medieval methods cannot have differed greatly from later hand production. Shoe nails are similar in size to armour rivets, making the following early twentieth-century description particularly relevant:

Herstellung geschmiedeter Nägel. Man 



verwendet in der Hauptsache Flußeisen 



in Form von Rundeisen und gewalztem 



oder […] geschnittenem Vierkanteisen 



[…]. Zur Bildung des Schafts, der 



Spitze und des Kopfs beim Schmieden 



von Hand dienen als Werkzeuge zur 



Herstellung kleiner und mittelgroßer 



Nägel der Amboß a, der Abschrot 



(Blockmeißel, Nagelschrot) b, das 



Nageleisen c auf dem Amboßstocke e 



und der Hammer d (Fig. 1–4). Das 



vierkantige Stabeisen wird im 



Schmiedefeuer auf Weißglut erhitzt, auf 



dem Amboß a Schaft und Spitze 



ausgeschmiedet und an der Stelle, 



welche den zu bildenden Kopf begrenzt, 



mittels der Schneide des Abschrotes b 



fast ganz abgehauen; schließlich wird 



der Schaft in das Loch des Nageleisens 



c gesteckt, die Stange durch eine leichte 



Wendung davon abgebrochen und der 



Kopf mit einigen Hammerschlägen 



fertiggemacht. Das Nageleisen c, 



welches im Auge der eisernen Stütze c1 



durch Verkeilen befestigt wird, hat an 



der Lochstelle für Nägel mit hohlen 



Köpfen eine gewölbte Erhöhung 



(Krone); […] Durch einen Schlag mit 



dem Hammer von unten her wird der 



Nagel aus dem Loch herausgeschlagen. 



An Stelle der Kopfbildung aus freier 



Hand verwendet man besonders bei 



einfachen Kopfformen Gesenke (s.d.) 



die als Handgesenke aus einem kurzen 



Stück Flacheisen bestehen und an 



ihrem verstählten Ende die Form des zu 



schmiedenden Nagelkopfs tragen […] 



Jeder Nagel wird in einer Hitze 



fertiggemacht, bei kleineren Nägeln 



werden zwei Stück in derselben Hitze 



hergestellt. Ein Nagelschmied verfertigt 



täglich in 12 Stunden 2000–2500 



Schuhnägel (etwa 1 kg) […]
Lueger (1908), pp. 570–571. German source text; note 119.

Revised translation:119

Manufacture of forged nails. The principal material is mild steel in round bars or in rolled or […] cut square bars […]. For hand-forging the shank, point and head of small and medium-sized nails, the tools are the anvil a, the cutting chisel (Blockmeißel, Nagelschrot) b, the nail header c on the anvil block e, and the hammer d (Figs 1–4). The square bar is heated to a white heat in the forge. The shank and point are forged on the anvil a, and the bar is almost severed on the cutting edge of b at the point delimiting the metal needed for the head. The shank is then inserted into the hole in the nail header c, the bar is broken away with a slight twist, and the head is finished with a few hammer blows. The nail header c is secured by a wedge in the eye of the iron support c1. For hollow-headed nails, it has a raised, curved crown around the hole […]. A hammer blow from below ejects the nail. Instead of forming the head freehand, especially for simple shapes, handheld dies may be used. These consist of short flat iron bars with a steeled end bearing the shape of the head to be forged […]. Each nail is completed in one heat; two small nails can be made in the same heat. In a twelve-hour day, a nail-maker produces 2,000–2,500 shoe nails, weighing about 1 kg […].
New English translation for this revision, based on the German passage quoted in the dissertation; the earlier translation remains in the original-text comparison.

These tools probably differed little from their medieval counterparts. A nineteenth-century nail-maker photographed at work [ref_ill_art_5380] PDF uses tools resembling those shown in a fifteenth-century depiction [ref_ill_art_5327] PDF.

Rivets must have been made by a similar process. For Types b and c, the head was finished with a hemispherical or conical punch die rather than the peen of a hammer. Type d heads must have been embossed. Cutting each ornamental ridge into a hollow head individually from outside would have been difficult and slow, probably requiring the head to be filled with a yielding but supportive material such as lead or a special resin. A punch-and-die drawing process is more likely, perhaps using the crown around the header hole described above.

Alternatively, the embossed heads may have been brazed to their shanks. Examination of an original rivet, for example with an endoscope, is needed to resolve this question. Forge-welding a shank to a pre-embossed head was probably impracticable: the thin metal would cool too quickly, and hammering would damage the decoration.

Copper-alloy caps for Type b rivets must have been drawn from thin sheet using a punch and die. Several domes were probably formed in one sheet before being cut out separately. The drawing operation may even have sheared each cap from the sheet. Before soldering, the iron head and the inside of the cap had to be cleaned of oxides with an acidic liquid. Without this preparation, joining them with tin solder would have been almost impossible.120

Attaching the caps required specialist skills comparable to those of a goldsmith. Gilding presented an additional difficulty. The caps may have been fire-gilded before soldering: if the order were reversed, the heat required for fire-gilding would melt the tin solder and destroy the joint.

Redaktionelle Hinweise · 2
  • Die englische Übersetzung des Lueger-Zitats ist ausdrücklich als neue Übersetzung gekennzeichnet. Der deutsche Quellenwortlaut und die frühere Übersetzung bleiben im Originalvergleich erhalten.
  • Die zunächst behauptete einteilige Herstellung von Typ d und die später erwogene Hartlötverbindung bleiben als ungeklärte Alternativen sichtbar.
Originalwortlaut vergleichen
4.2.1.6 The making of rivets 



The late medieval armourer would probably have been generally capable to make the 



required rivets by himself. As he was a specialized craftsman, his work-time was expensive 



and he would therefore certainly try to focus on his main work – designing the plates – rather 



than on mass-producing features like rivets. That there was a specialized craft -segment for 



the making of rivets is indicated by elaborately worked rivets of type -d, found at o ther 



contemporary ironworks, for example iron doors [ref_ill_art_5152]. An English 16th century 



source tells that rivets – just like all other semi-finished working material – were bought in 



by the armourer.116  



Despite intense research, the author could not find any pre -industrial description of rivet -



making.117 Nevertheless, rivets were always mass -produced items. In 1828 a nail -smith of 



Stirling betted that he could make 17030 nails within t wo weeks; he finished even earlier. 



Normally he would finish 700 nails within a working day of 12 hours.118 Their making is so 



simple that the medieval techniques cannot have differed much from the manufacture in later 



times. In the following, an early 20th century description of the hand-making of shoe-nails is 



quoted. The dimensions of shoe-nails are similar to armour-rivets and therefore the working-



processes must be very similar.



Herstellung geschmiedeter Nägel. Man 



verwendet in der Hauptsache Flußeisen 



in Form von Rundeisen und gewalztem 



oder […] geschnittenem Vierkanteisen 



[…]. Zur Bildung des Schafts, der 



Spitze und des Kopfs beim Schmieden 



von Hand dienen als Werkzeuge zur 



Herstellung kleiner und mittelgroßer 



Nägel der Amboß a, der Abschrot 



(Blockmeißel, Nagelschrot) b, das 



Nageleisen c auf dem Amboßstocke e 



und der Hammer d (Fig. 1–4). Das 



vierkantige Stabeisen wird im 



Schmiedefeuer auf Weißglut erhitzt, auf 



dem Amboß a Schaft und Spitze 



ausgeschmiedet und an der Stelle, 



welche den zu bildenden Kopf begrenzt, 



mittels der Schneide des Abschrotes b 



fast ganz abgehauen; schließlich wird 



der Schaft in das Loch des Nageleisens 



c gesteckt, die Stange durch eine leichte 



Wendung davon abgebrochen und der 



Kopf mit einigen Hammerschlägen 



fertiggemacht. Das Nageleisen c, 



welches im Auge der eisernen Stütze c1 



durch Verkeilen befestigt wird, hat an 



der Lochstelle für Nägel mit hohlen 



Köpfen eine gewölbte Erhöhung 



(Krone); […] Durch einen Schlag mit 



dem Hammer von unten her wird der 



Nagel aus dem Loch herausgeschlagen. 



An Stelle der Kopfbildung aus freier 



Hand verwendet man besonders bei 



einfachen Kopfformen Gesenke (s.d.) 



die als Handgesenke aus einem kurzen 



Stück Flacheisen bestehen und an 



ihrem verstählten Ende die Form des zu 



schmiedenden Nagelkopfs tragen […] 



Jeder Nagel wird in einer Hitze 



fertiggemacht, bei kleineren Nägeln 



werden zwei Stück in derselben Hitze 



hergestellt. Ein Nagelschmied verfertigt 



täglich in 12 Stunden 2000–2500 



Schuhnägel (etwa 1 kg) […]119 



Production of forged nails. Mainly 



mild-steel bars of round section or 



of either rolled or cut quadrangular 



section are used. For the hand 



forging of the shank, the point and 



the head of medium and small size 



nails the following tools are used: 



The anvil a, the cutting stake -



chisel (Blockmeißel, Nagelschrot ) 



b, the nail -iron c on the anvil -



foundation e and the hammer d 



(fig. 1 -4). The iron pole of 



quadrangular section is heated in 



the fire until white -hot, the shank 



and the point is forged on the anvil 



a, by hammering it onto the stake 



chisel b it is cut off  almost 



completely, leaving enough 



material for the head; finally the 



shank is stuck in the hole of the 



nail-iron, the pole is broken off by 



a slight turn and the head is 



finished with a few strikes of the 



hammer. The nail-iron c, which is 



wedged to the ey e of the iron 



support c1, has a flange (crown) 



around the hole for making rivets 



with hollow heads. By a blow of 



the hammer from below the nail is 



driven off the hole. Instead of the 



free-shaping of the head especially 



for simple head -shapes handheld 



dies, made from a flat bar of steel 



which has at its tempered end the 



[negative] shape of the rivet head 



attached […] Each nail is finished 



in one heat, of smaller rivets two 



items are forged in one heat. A 



nail-smith produces in a 12 hour 



day 2000-2500 shoe-nails (about 1 



kg) […]



The tools mentioned, do most likely not differ much from those used in the Middle Ages. A 



19th century nail-maker at work is seen on the photograph [ ref_ill_art_5380]. The tools are 



similar to those used for nail-making in the 15th century [ref_ill_art_5327].  



Rivets must have been made by the nail -making process described above. The only 



difference is that the heads of type -b and -c rivets were not finished by the cross of the 



hammer, but by a punch-die of cone or dome shape. The heads of type -d rivets must have 



been finished by embossing. It would have been very difficult and time consuming to freely 



emboss the ridges on each single rivet -head with the chisel from the exterior. For this 



technique, the interior of the already dome -shaped head would probably have to be filled 



with some flexible, but resisting substance like lead or a special resin. It is more likely that 



the heads are actually made by a “punch -and-die” deep drawing technique. Maybe for this 



purpose, the nail -iron was designed with a “crown” around the shank -hole, as described 



above. Another possibility is that the rivet heads were hard -soldered to the shanks. To 



answer this question, a genuine rivet needs to be examined, e. g. by means of an endoscope. 



It was most likely not possible to fire-weld the shank to the pre-embossed head, as the thin 



materials would not keep the heat long enough  and the hammering would damage the 



embossing.  



The copper alloy caps on certain type-b rivets have to be shaped by deep drawing them from 



a thin plate, with the help of a punch and a die. Probably several domes were driven into the 



plate, before the single caps were separately cut off. Maybe the domes were also driven into 



a die so extensively that the single caps got sheared off the plate in the same turn. The iron 



rivet-head and the interior of the cap needed to be etched with an acetous liquid to clean off 



oxides from the surface. Without this procedure, it would have been almost impossible to 



braze the caps to the rivets by means of tin-solder.120 The process of brazing the caps to the 



rivet-heads requires special skills, actually those of a goldsmith. Especially the gilding of the 



caps was problematic. Maybe this was done by fire -gilding the cap before it was brazed to 



the rivet. The other way round, the high temperature necessary for the fire gilding would 



destroy the tin-solder joint as it melts at lower temperatures.
S. 97–98 · Sprachlich überarbeitet · Entwurf

4.2.1.7 Setting rivets

A rivet is supplied as a semi-finished component with one preformed head. Its shank is passed through holes in the elements to be joined, and the assembly is supported with that head against an anvil. A softer material, such as hardwood or lead, can be placed between head and anvil to prevent damage. Flat Type a heads on the inside can rest directly on the anvil.

For sliding plate joints, or when leather is secured with a Type b, c or d rivet, a washer is placed over the shank on the inside before the closing head is formed. A washer is unnecessary for simple pivoting or rigid joints, or when leather is attached internally with a Type a rivet. In the latter case, the plate hole is countersunk from outside. This allows the shank to spread sufficiently to remain secure after the closing head has been ground flush to conceal the rivet.

If necessary, the shank is shortened to project only a few millimetres beyond the plate or washer—enough material for a secure closing head. A hammer, for example one with a rounded peen, is used to flatten the end carefully and spread it evenly in all directions. A small forked plate can hold the washer down during riveting; such a tool appears on the workbench at the lower right of [ref_ill_art_5330] PDF (description 2). Even hammering prevents the shank from bending.

Depending on the material’s toughness, rivets up to perhaps 10 mm in diameter can generally be set without heating. Since armour rivet shanks are usually less than 4 mm thick, they were certainly set cold.

Originalwortlaut vergleichen
4.2.1.7 Riveting 



In practice, rivets come as a semi-finished item with one side already widened to form a pre-



made head. The shank of the rivet is plugged through holes in the segments that need to be 



fastened together. The work-piece then is placed with the pre -made rivet-head on an anvil. 



To avoid damages to the pre-made head, a somewhat softer material like hard-wood or a bar 



of lead needs to be put in between the head and the anvil. Interior heads of type-a rivets can 



be placed directly on the anvil. For a sliding plate-to-plate joint or where leather is attached 



by means of a type-b, -c or -d rivet, interiorly a washer is placed under the rivet head before 



the riveting. This is not necessary for simple pivoting or fixed joints or where leat her is 



riveted directly to the plate from the interior by rivets of type -a. In the latter cases, the hole 



in the plate was counter -bored from the outside. This allows the shank to splay enough to 



still hold, when the second head would be ground flush to conceal the rivet. 



If necessary, the shank is cut to surmount the plate or washer only by a few millimeters, just 



sufficiently to form a secondary head large enough to hold the rivet safely in place. By means 



of a hammer with e. g. a bowl shaped peen, the end of the shank is carefully hammered flat 



while extending its diameter to all directions. Throughout the riveting a washer can be held 



down by means of a small fork -shaped plate, as can be seen on the workbench in the right



lower corner of the image [ref_ill_art_5330] (descr. 2). To prevent the shank from bending, 



the worker has to take care not to hammer one side stronger than the other. With rivets of 



diameters maybe up to 10 mm, of cours e also depending on the toughness of the material, 



this work could usually be done without heating the rivet. As the shanks of rivets for armour 



pieces usually show diameters under 4 mm, they all had certainly been riveted cold.
S. 98 · Sprachlich überarbeitet · Entwurf

4.2.1.8 Distinguishing old rivets from modern replacements

Understanding the characteristic differences between old, handmade rivets and modern, machine-made ones is important when assessing authenticity.121 The following criteria are not absolute rules, but they provide useful evidence.

Rivets and nails were not machine-made before the nineteenth century. Modern standardised rivets are generally uniform, whereas handmade examples show irregularities. The difficulty is that some workshops continued making nails—and presumably rivets—by hand into the early twentieth century.

Rivets securing leather that is evidently modern cannot be original to that assembly. Opening and reusing a rivet is almost impossible because the remaining shank would be too short to form another closing head. Reuse would require the shank to be lengthened by welding or brazing on a piece of wire.

Originalwortlaut vergleichen
4.2.1.8 Differing between “old” and “new” rivets 



The detailed comprehension of the characteristic features of “old” (handmade) and “new” 



(machine-made) rivets 121 are important for the authenticity -testing of armour. The 



acceptance of a few points – which are not meant to be set in stone – certainly delivers some 



reliable facts for getting closer to the answer on the authenticity question. 



Until the 19 th century, no machines were used for the making of rivets or nails. Modern 



standardized machine -made rivets usually have a uniform appearance, whereas the 



handmade rivets are somewhat imperfect. What actually makes the determination difficult 



is the fact that nails – and therefore presumably also rivets – were still made by hand in the 



early 20ieth century in some workshops. Where rivets hold leather in a condition that is most 



likely not old, the rivets cannot be genuine. It is almost impossible to open and reuse a rivet, 



as the shank would afterwards be too short for re -riveting. The only possibility would be to 



lengthen the shanks by the welding or hard-soldering of a wire.
S. 98 · Sprachlich überarbeitet · Entwurf

4.2.1.8.1 Type a

Plain Type a heads offer few distinctive features, making original examples difficult to identify. Roofing nails used to secure roofing felt, available today and also in the nineteenth century, can serve as Type a rivets once their shanks are cut to length. Modern examples are iron with a protective zinc coating.

Old handmade rivets may be less regular and have burrs around their head edges, but, apart from galvanising, distinguishing them from modern substitutes is difficult. The zinc can readily be removed with acid or by heating. Some present-day restorers and armourers use such nails as rivets.

Originalwortlaut vergleichen
4.2.1.8.1 Type-a  



It is often not easy to determine if the plain rivet heads of type-a are genuine. As they do not 



show many formal features, there is not much to compare to possibly modern examples. In 



modern building-supply stores, a certain type of nail, used mainly for the fixing of tar paper 



on house-roofs, is available. The same sort was also available in the 19th century. The modern 



nails are made of iron, coated with zinc against corrosion. When their shanks are cut to the 



desired length, they can be used as rivets of type -a. The old, handmade rivets might look 



more irregular and the edges of the heads are often burred. Except of the zinc coating, it is 



very difficult to differ between genuine and modern examples. The coating could easily be 



removed by acid or by heating the nails in a fire. Some restorers or armourers use the 



aforesaid nails as rivets today.
S. 98–99 · Sprachlich überarbeitet · Entwurf

4.2.1.8.2 Types b and c

Machine-made rivet dimensions have been standardised since the nineteenth century. Handmade Types b and c vary slightly in size and in the alignment of head and shank,122 and their head edges often have burrs. Standard machine-made rivets with heads comparable to old handmade examples are available in only a limited range. Their shanks are generally about 4 mm in diameter, whereas old examples are usually below 3.5 mm. A relatively large head on a thin shank may therefore indicate an old rivet. Small empty holes can support the same interpretation.

Nevertheless, machine-made heads can easily be reworked. Non-standard proportions can also be reproduced by turning123 or by making pressing dies to the required dimensions. Solid copper-alloy rivets joining two iron components are most likely modern replacements. Archaeological objects consistently use iron rivets for structural iron-to-iron joints, probably for reasons of reliability.

Copper-alloy caps on iron rivets do not necessarily establish originality: they also occur on the reproduction suit [ref_arm_4141] PDF, with details visible on [ref_arm_608] PDF. David Starley cites Robert Smith’s observation that large quantities of brass-capped rivets were still supplied to the Tower of London Armouries for repairing old armour in the early nineteenth century.124 Using X-ray fluorescence analysis of cap composition, Starley proposed a method that may help distinguish old rivets from modern ones.125

Originalwortlaut vergleichen
4.2.1.8.2 Type-b and -c 



The sizes of machine-made rivets are standardized since the 19 th century. Handmade rivets 



of type-b and -c vary slightly in their dimensions and in the shank -head symmetry122. The 



edges of the heads are often burred. The supply of standardized mac hine-made rivets with 



heads comparable in size to the handmade “old” rivets is limited. They usually have shanks 



of about 4 mm in diameter, whereas the “old” ones are below 3.5 mm in diameter. This 



means: Rivets with shanks of a thin diameter but a comparatively large head might be “old”. 



Even where rivets are missing, the “empty” small -diameter holes can support such an 



assumption. Nevertheless, it is not difficult to alter machine-made rivets by reworking their 



heads. Even not-standardized dimensions could be produced by modern methods: To get to



the desired shank-head diameter ratio of “old” models rivets could be produced by turning123 



or the dies of rivet-pressing machines could be designed in the required dimensions. 



Massive copper alloy rivets that connect two iron parts are most likely modern replacements. 



According to all archaeological objects – probably for safety reasons – at constructive iron-



to-iron joints always iron rivets were used.  



Brazed copper heads on iron rivets are not always likely to b e genuine, as they also appear 



e. g. at the reproduced suit [ ref_arm_4141] (for detailed images of the rivets see 



[ref_arm_608]). David Starley quotes Robert Smith, who says that by the early 19th century 



brass capped rivets were still delivered in large numbers to the Armouries in the Tower of 



London for the repairing of ancient armour. 124 With the examination of the chemical 



components of rivet-caps by means of XRF-analysis, Starley developed a theory that could 



help to distinguish between “modern” and “old” rivets.125
S. 99 · Sprachlich überarbeitet · Entwurf

4.2.1.8.3 Type d

Original rivets with elaborately shaped, ridge-decorated heads are always hollow beneath the head126 and made from a single piece of iron.127 Their manufacture requires skills beyond ordinary rivet-making, making reproductions with these features very unlikely. A reproducer might instead make the head solid.

Redaktionelle Hinweise · 1
  • Die Sicherheit dieses Echtheitskriteriums und die einteilige Fertigung sind Aussagen des Originals; sie wurden nicht zu einem neu validierten Prüfverfahren erhoben. Vgl. die offenen Fertigungsalternativen in §4.2.1.6.
Originalwortlaut vergleichen
4.2.1.8.3 Type-d 



Awkwardly shaped genuine rivets are always hollow inside their ridge -decorated heads.126 



They are also made of one piece of iron.127 As their making requires skills beyond the regular 



rivet-making it is very unlikely that rivets with these features are reproductions. A reproducer 



might have made the heads massive.
S. 99 · Sprachlich überarbeitet · Entwurf

4.2.2 Washers

Washers are small plates with a single hole, placed over a rivet shank before its closing head is formed. They mainly serve either to enlarge the effective bearing area of that head or to decorate the object.

When a rivet’s large preformed head has a decorative role and lies outside, its washer often lies inside. Washers are needed where a joint must remain loose enough for its components to move independently. They are consistently used when riveting leather to plate, preventing the flexible material from pulling over the rivet under tension. For similar reasons, they may be used when attaching ring armour to plate armour. Three forms can be distinguished.

Redaktionelle Hinweise · 1
  • „Washers are only necessary“ ist im Original durch die unmittelbar folgenden Verwendungen bei Leder und Ringpanzerung eingeschränkt. Die Überarbeitung erhält alle beschriebenen Funktionen ohne eine ausschließlich auf bewegliche Metallverbindungen bezogene Regel.
Originalwortlaut vergleichen
4.2.2 Washers 



Washers are small, one -time pierced plates, put upon the shank of a rivet before staking. 



These plates can serve mainly two different purposes. They can extend the diameter of the 



shank flattened by staking or they can simply decorate an item. 



A washer is often found at rivet-joints if the large “factory-head” of the rivet has an additional 



decorative character and is thus lying at the outside of an armour piece. The washer itself is 



then attached interiorly. Washers are only necessary where two segments are fastened 



together in a way that the rivets need to remain loose, to allo w an independent motion of 



each of the fastened elements. Washers are consistently found where leather is riveted to a 



plate, to prevent the flexible leather from slipping off the rivet shank when under tension. 



For similar reason, washers might be used where ring-armour is attached to plate armour. In 



the following, three types of washers will be classified.
S. 99 · Sprachlich überarbeitet · Entwurf

4.2.2.1 Type a: square washers

[ref_ill_was_a] These are the simplest washers. A larger sheet was probably pierced repeatedly and then cut into small squares, perhaps with large plate shears. They are rare on armour and occur only inside. Those around the brim of [ref_arm_1360] PDF probably once secured an internal lining.

Originalwortlaut vergleichen
4.2.2.1 Type-a [ref_ill_was_a] 



This is the simplest version of washers. They were most likel y made by the piercing of a 



larger plate several times and the small washers were cut off in a square pattern – possibly 



with the help of large plate -shears. Such washers are rarely found on armour and they are 



used only interiorly. At the brim of the helmet [ref_arm_1360] they probably once helped to 



fix an interior lining.
S. 100 · Sprachlich überarbeitet · Entwurf

4.2.2.2 Type b: clipped-corner washers

[ref_ill_was_b] Type b was made like Type a, but the corners of each square were clipped to produce an octagon. Removing the corners reduced the risk of injury or damage to clothing. This is the most common form, used internally in all production regions, both for leather attachments [ref_arm_1272] PDF and sliding rivet joints [ref_arm_613] PDF.

Originalwortlaut vergleichen
4.2.2.2 Type-b [ref_ill_was_b] 



Washers of type-b are basically made the same way as type-a washers. The difference is that 



the corners of each square plate were cut off to reveal an octagonal pattern. This shape 



avoided injuries and prevented clothes from getting damaged. This is the most common 



washer-type, frequently used interior ly for the attachment of leather -parts [ref_arm_1272] 



or for sliding rivet-joints [ref_arm_613] in all production regions.
S. 100 · Sprachlich überarbeitet · Entwurf

4.2.2.3 Type c: round washers

[ref_ill_was_c] Round Type c washers occur particularly on Italian armour where leather is attached inside. They usually have a slightly embossed section [ref_arm_3097] PDF. They were probably stamped from a larger sheet, since cutting them individually with shears would have been uneconomical.

Copper-alloy examples secure the lining of the probably Spanish helmet [ref_arm_1418] PDF. Many Type c washers are modern replacements made as standard flat discs [ref_arm_3272] PDF [ref_arm_2308] PDF, but older embossed forms also appear to have been reproduced [ref_arm_9] PDF.

Originalwortlaut vergleichen
4.2.2.3 Type-c [ref_ill_was_c] 



Round washers of type-c are found particularly on Italian armour, where leather is riveted to 



the interior. They usually have a slightly embossed section [ ref_arm_3097]. Such washers 



were probably stamped from a larger plate, as it would be unprofitable to cut them with 



shears. At the presumably Spanish helmet [ ref_arm_1418] type-c washers made of copper 



alloy hold the interior lining. In many cases, type-c washers are modern replacements of flat, 



standardized discs [ref_arm_3272] [ref_arm_2308], but also the embossed ancient versions 



seem to have been reproduced [ref_arm_9].
S. 100 · Sprachlich überarbeitet · Entwurf

4.2.3 Permanent joints

Rivets were used in several kinds of plate joint. During the fifteenth century, European armourers developed sophisticated permanent connections that allowed articulation. The principal forms are classified and explained below.

Originalwortlaut vergleichen
4.2.3 Non-detachable joints 



Rivets were used for different types of plate -joints. In the 15 th century the European 



armourers developed sophisticat ed articulated permanent fastening -systems. The most 



important types are classified and explained in the following paragraphs.
S. 100 · Sprachlich überarbeitet · Entwurf

4.2.3.1 Rigid riveted joints

[ref_ill_joi_fixedbyrivet] The simplest connection holds two plates tightly together so that neither can turn around the rivet. The segments of Type II helmets, for example, were generally joined permanently in this way [ref_arm_1471] PDF.

During the fifteenth century, rigid plate-to-plate riveting was relatively uncommon. The technique was chiefly used to attach hinges, leather straps and decorative elements. Armpit plates may provide an exception: details on the statue [ref_ill_art_5198] PDF and the surviving example [ref_arm_5116] PDF, still attached to a shoulder defence, suggest that they could be riveted directly to the shoulder plate. The chest and abdominal plates of many breastplates were also rigidly riveted together [ref_arm_3633] PDF.

Originalwortlaut vergleichen
4.2.3.1 Fixed by rivet [ref_ill_joi_fixedbyrivet] 



The simplest joining of two plates is riveting them tightly together, so they do not pivot 



around the rivet. The segments of type -II helmets for example were usually fixed 



permanently together by this technique [ref_arm_1471]. In the 15th century only in rare cases 



plates were stiffly fixed together by rivets. In this time, this technique was merely used for 



the attachment of hinges, leather -straps or decorative applications. Exceptions are maybe 



armpits. They could probably be riveted directly to the shoulder defense, as the details at the 



statue [ref_ill_art_5198] and the extant example [ref_arm_5116] (still attached to a shoulder 



defense) suggest. Also the torso - and the abdomen -plate of many breastplates were 



permanently fixed by such joints [ref_arm_3633].
S. 100 · Sprachlich überarbeitet · Entwurf

4.2.3.2 Pivoting rivet joints

[ref_ill_joi_pivotingrivet] A pivoting joint resembles a rigid riveted connection, but the shank is slightly smaller than the holes and the rivet is not closed tightly. This allows the plate to rotate around it.

The most familiar examples are visor pivots, particularly on Type IV [ref_arm_1529] PDF, Type VI [ref_arm_1944] PDF and Type VII helmets [ref_arm_1704] PDF. Most pelvic, elbow, knee, foot and neck lames, together with the upper plates of Type III back protection, were also joined in this way. The technique was probably first used in armour around the mid-fourteenth century, when articulated face guards appeared and separate limb defences began to be connected.

Originalwortlaut vergleichen
4.2.3.2 Pivoting rivet [ref_ill_joi_pivotingrivet] 



A joint that only needs to allow a plate to pivot works actually similar to a fixed rivet -joint. 



The difference is that the shank of the rivet is in diameter slightly smaller than the rivet-holes 



and the rivet is not hammered very tight. The most common examples are the pivoting-joint 



of face-guards merely at helmets of type -IV [ref_arm_1529], -VI [ref_arm_1944] and -VII 



[ref_arm_1704]. But also pelvis -lames, elbow lames, knee lames, foot lames, neck lames 



and the upper plates of backplates of type -III in most cases were joined by this technique. 



On armour this type of joint was presumably used for the first time in the mid-14th century, 



when the first helmets got an articulated face -guard and when the single parts of the limb -



protections were joined together.
S. 100–101 · Sprachlich überarbeitet · Entwurf

4.2.3.3 Plates riveted to internal leather straps

[ref_ill_joi_rivetedtoleather] Lames requiring articulation could be connected by an internal leather strap. This arrangement was usually combined with pivoting or sliding rivets, as on the lower lames of shoulder defences [ref_arm_262] PDF [ref_arm_425] PDF and the upper lames of thigh defences [ref_arm_2368] PDF [ref_arm_2883] PDF.

On many pelvic assemblies [ref_arm_3306] PDF [ref_arm_3604] PDF [ref_arm_3618] PDF and foot defences [ref_arm_2245] PDF [ref_arm_2254] PDF, a central leather strap prevented the lames from overturning. Some pelvic lames were connected exclusively by leather [ref_arm_3875] PDF. Original straps are often lost or replaced. Holes or rivets that otherwise appear to have no function, visible only inside, commonly indicate their former presence.

This method probably developed directly from lacing separate segments together. Fourteenth-century torso plates were generally still joined by a leather or textile support riveted inside [ref_arm_3811] PDF or outside [ref_arm_3698] PDF. Towards the end of the century, the leather was placed inside and reduced from a lining-like support to narrow straps.

Originalwortlaut vergleichen
4.2.3.3 Riveted to leather [ref_ill_joi_rivetedtoleather] 



Wherever single lames should be articulated, they could be connected by an interior leather 



strap. In most cases this system is  combined with a pivoting or sliding rivet -joint, for 



example at: the lower lames of shoulders [ref_arm_262] [ref_arm_425], the upper lames of 



upper legs [ ref_arm_2368] [ ref_arm_2883]. At many pelvis -lames [ ref_arm_3306] 



[ref_arm_3604] [ ref_arm_3618] and at the lames of foot -protections [ ref_arm_2245] 



[ref_arm_2254] a centrally attached leather strap prevented the lames from flipping over. In



some cases the pelvis -lames are connected exclusively by leather straps [ ref_arm_3875]. 



The leather straps at joints are often lost or they were replaced in later times. Usually, 



functionless holes or remaining functionless rivets – both only visible interiorly – tell of their 



former existence. This technique is probably the technique to follow  in its development 



directly onto the lacing of single segments. In the 14th century, the plates of torso-protections 



were usually still joined by an in - [ref_arm_3811] or exteriorly [ref_arm_3698] riveted 



leather or fabric. Towards the end of the century, the leather was attached interiorly and the 



former lining-like appearance was reduced to narrow stripes.
S. 101 · Sprachlich überarbeitet · Entwurf

4.2.3.4 Sliding rivet joints

[ref_ill_joi_slidingrivet] Sliding rivets allow plates both to pivot and to slide. They frequently connect the lames of Type III hand protection [ref_arm_1063] PDF, shoulder defences [ref_arm_861] PDF, the outer, little-toe side of knee lames [ref_arm_2471] PDF, and thigh lames [ref_arm_2412] PDF. They also occur occasionally on the pelvic lames of German breastplates and backplates [ref_arm_3294] PDF. The central joint of a Type IV breastplate [ref_arm_3636] PDF and separate plates around the arm openings [ref_arm_3463] PDF often slide in the same way.

The slot is always filed in the underlying plate. The rivet is set loosely, with an internal washer to prevent it from pulling through. This joint probably developed in the early fifteenth century and was first used on Italian knee protection.

In the late fifteenth century, German armourers sometimes attached hand-protection plates directly to forearm defences. A rivet travelled in a long slot, cut either in the main plate [ref_arm_120] PDF or in a separate strip of metal attached inside [ref_arm_4926] PDF.

Originalwortlaut vergleichen
4.2.3.4 Sliding rivet [ref_ill_joi_slidingrivet] 



Sliding rivets allow the lames to pivot and to slide. This system is frequently used at the joint 



of the single lames of type -III hand -protections [ ref_arm_1063], at shoulder -lames 



[ref_arm_861], at the small toe side of knee lames [ ref_arm_2471] and at upper leg lames 



[ref_arm_2412]. It is sometimes found at pelvis -lames of German breast - and backplates 



[ref_arm_3294]. Also the central joint at type -IV breastplates [ ref_arm_3636] and the 



separate arm-cutouts at breastplates [ref_arm_3463] are often sliding. The slot is always filed 



into the plate placed underneath. The ri vet is fastened loosely; interiorly a washer is 



necessary to prevent the rivet from falling out. This joint -type was probably developed in 



the early 15 th century and used first for the knee protections on Italian armour. In the late 



15th century, the German armourers attached a few plates for the protections of the hands 



directly to the lower arm defenses. These plates were fastened via a rivet sliding in a long 



slot. The slot was either filed into the main -plate [ ref_arm_120] or it was filed into an 



interiorly attached stripe of plate [ref_arm_4926].
S. 101 · Sprachlich überarbeitet · Entwurf

4.2.3.5 Sliding rivets in projecting tabs

[ref_ill_joi_slidingrivetwithnoseatedge] A variant found on many objects from the second half of the fifteenth century places the slot in a projecting tab on the edge of the inner lame. This probably reduced weight by limiting the amount of plate overlap elsewhere [ref_arm_865] PDF.

Originalwortlaut vergleichen
4.2.3.5 Sliding rivet with nose at edge 



[ref_ill_joi_slidingrivetwithnoseatedge] 



There is a variation of the aforesaid system to be found at many items of the second half of 



the 15th century. Here the interior lame-edge forms a nose where the slot is piercing the plate. 



The intention was probably to save weight by the reduction of the plate -overlap 



[ref_arm_865].
S. 101 · Sprachlich überarbeitet · Entwurf

4.2.3.6 Rotation through sliding rivets

[ref_ill_joi_turningviaslidingrivets] A distinctive articulation system occurs exclusively between Type II elbow protection and Type III forearm protection on Italian arm defences. Two or three slots near the upper end of the outer forearm plate receive loosely set rivets connecting it to the lowest elbow lame [ref_arm_1] PDF [ref_arm_810] PDF. As the rivets travel in these slots, the forearm defence can rotate. The system had developed by the late fourteenth century and remained in use until the late fifteenth.

Originalwortlaut vergleichen
4.2.3.6 Turning via sliding rivets [ref_ill_joi_turningviaslidingrivets] 



A unique system for the articulation of armour plates is found exclusively at the joint 



between elbows of type-II and lower arms of type-III on Italian arm defenses. Here the outer 



plate of the lower arm at its upper end is pierce d by two or three slots and connected to the 



lowest lame of the elbow by loosely fitted rivets, sliding in these slots [ ref_arm_1] 



[ref_arm_810]. This joint-type allows the lower arm to be turned. It was developed already 



by the end of the 14th century and remained in use until the late 15th century.
S. 101 · Sprachlich überarbeitet · Entwurf

4.2.3.7 Externally mounted hinges

[ref_ill_joi_hingeexterior] Hinges may be riveted to the outside of a plate. Fifteenth-century examples are generally small, with filed edge decoration. Some German examples are made from copper-alloy sheet.

External hinges connect the plates of Type III lower-leg protection [ref_arm_2309] PDF, the side plates of Type II thigh protection [ref_arm_2879] PDF, breastplates and backplates [ref_arm_3876] PDF, and the opening plates of Type III forearm protection [ref_arm_365] PDF. They also occur on opening hand-protection cuffs [ref_arm_1207] PDF, thumb defences [ref_arm_1272] PDF, and the cheek plates of Type II helmets [ref_arm_1447] PDF.

Originalwortlaut vergleichen
4.2.3.7 Exteriorly attached hinge [ref_ill_joi_hingeexterior] 



A hinge can be riveted exteriorly to the plate. In the 15 th century, such hinges are usually 



small and the edges are decorated by filing. In some cases, on German armour they are made 



of copper alloy plate. They can connect the plates of type-III lower legs [ref_arm_2309], the 



flaps of type -II upper legs [ ref_arm_2879], the breast - and the backplate [ ref_arm_3876], 



the flap of the lower arms of type -III [ ref_arm_365], the flaps on hand -protection-cuffs 



[ref_arm_1207], the thumbs [ ref_arm_1272] or the cheek -pieces at helmet s of type -II 



[ref_arm_1447].
S. 101–102 · Sprachlich überarbeitet · Entwurf

4.2.3.8 Internally mounted hinges

[ref_ill_joi_hingeinterior] Armourers concealed hinges inside as early as the fourteenth century, probably to keep the outer surface as smooth as possible. This arrangement connects the opening plates of Type III lower-leg [ref_arm_2291] PDF and forearm defences [ref_arm_986] PDF, opening hand defences [ref_arm_1272] PDF, the cheek plates of Type VI helmets [ref_arm_1919] PDF [ref_arm_1929] PDF, and the segments of some Type II back protection [ref_arm_3334] PDF.

Originalwortlaut vergleichen
4.2.3.8 Interiorly attached hinge [ref_ill_joi_hingeinterior] 



Already in the 14 th century, the armourers hi d the hinges interiorly, probably to leave the 



exterior surface as even as possible. The flaps of type -III lower legs [ ref_arm_2291] and



arms [ref_arm_986] were connected by this system, but also the flaps of hand -protections 



[ref_arm_1272], the cheek -plates of type -VI helmets [ ref_arm_1919] [ref_arm_1929] and 



the single segments of some type-II backplates [ref_arm_3334].
S. 102 · Sprachlich überarbeitet · Entwurf

4.2.3.9 Wedge-shaped rivets

[ref_ill_joi_wedge] On the Type IV helmet [ref_arm_2121] PDF and Type V helmet [ref_arm_2120] PDF, small wedge-shaped rivets run along the upper edge of a now-lost metal or leather strip that supported the ring-armour collar. They probably diverted sword blows away from the leather or helped a second helmet slide over the first.

Originalwortlaut vergleichen
4.2.3.9 Wedge [ref_ill_joi_wedge] 



On helmets of type-IV [ref_arm_2121] and -V [ref_arm_2120] along the upper edge of the 



lost plate or leather strap for the attachment of the ring -armour collar small wedge-shaped 



rivets are attached. They were probably meant to lead blows of swords etc. away from the 



leather or they were meant to ease the over-slipping of a second helmet.
S. 102 · Sprachlich überarbeitet · Entwurf

4.2.4 Detachable joints

Some armour elements had to be removable, whether attached to one another or to the wearer. Armourers developed several forms of detachable connection. The principal recurring types are described below.

Originalwortlaut vergleichen
4.2.4 Detachable joints 



Some of the single armour parts needed to be fastened in a removable manner, either to one 



another or to the wearer’s body. The armourers developed different kinds of detachable 



joints. The most important and repeatedly found types are introduced in the following.
S. 102 · Sprachlich überarbeitet · Entwurf

4.2.4.1 Bolt and eye

[ref_ill_joi_boltandeye] A bolt-and-eye joint can connect the abdominal and chest plates of a breastplate [ref_arm_3621] PDF [ref_arm_3624] PDF [ref_arm_3678] PDF, or secure shoulder [ref_arm_633] PDF [ref_arm_663] PDF and elbow reinforcements [ref_arm_888] PDF [ref_arm_5044] PDF. This form first appeared on armour in the first half of the fifteenth century.

Originalwortlaut vergleichen
4.2.4.1 Bolt and eye [ref_ill_joi_boltandeye] 



The abdomen - and the thorax -plate of breastplates [ ref_arm_3621] [ ref_arm_3624] 



[ref_arm_3678], the reinforces of shoulders [ ref_arm_633] [ ref_arm_663] and elbows 



[ref_arm_888] [ref_arm_5044] can be connected by a bolt-and-eye joint. This joint-type was 



first applied on armour in the first half of the 15th century.
S. 102 · Sprachlich überarbeitet · Entwurf

4.2.4.2 Tubular attachment studs

[ref_ill_joi_tubepulley] On mid-fourteenth-century Type IV helmets, tubular studs secured the ring-armour collar. They could be made by rolling the square head of a rivet, essentially of Type a, into a tube [ref_arm_1504] PDF, or by folding a small plate [ref_arm_1542] PDF [ref_arm_1564] PDF. Solid examples with drilled holes also exist [ref_arm_2121] PDF. This form ceased to be fitted to helmets by the end of the fourteenth century.

Redaktionelle Hinweise · 1
  • „Pulley“ wird für diese gelochten Befestigungselemente neutral als „attachment stud“ wiedergegeben. Kein bewegliches Rollenbauteil hinzuinterpretiert; Zeichnungs-ID bleibt unverändert.
Originalwortlaut vergleichen
4.2.4.2 Tube pulley [ref_ill_joi_tubepulley] 



At type-IV helmets of the mid-14th century the ring -armour collar was attached via tube -



shaped pulleys. Their making was very simple: the square head of a rivet – basically of type-



a – was rolled to form a tube [ref_arm_1504] or the pulleys were made from a simply turned 



plate [ref_arm_1542] [ref_arm_1564], but also massive versions with the hole drilled exist 



[ref_arm_2121]. These pulleys were only attached to helmets before the end of the 14 th 



century.
S. 102 · Sprachlich überarbeitet · Entwurf

4.2.4.3 Square-section attachment studs

[ref_ill_joi_squarepulley] Studs with a square section could secure the ring-armour collar to the helmet skull [ref_arm_2112] PDF. Their production for this purpose ceased around 1400.

Originalwortlaut vergleichen
4.2.4.3 Square pulley [ref_ill_joi_squarepulley] 



The ring-armour collar could be attached to the helmet-skull via pulleys with a square section 



[ref_arm_2112]. From the 1400’s on these pulleys were not produced for this purpose 



anymore.
S. 102 · Sprachlich überarbeitet · Entwurf

4.2.4.4 Rounded attachment studs

[ref_ill_joi_bowlpulley] Rounded studs of iron or copper alloy are riveted around the lower edges of some Type IV [ref_arm_1520] PDF [ref_arm_1562] PDF, Type V [ref_arm_2082] PDF and Type VI helmets [ref_arm_1933] PDF. They secure a leather or metal strip [ref_arm_2183] PDF carrying the ring-armour collar. A single wire or leather lace passed through all the studs to retain the strip. Production of this form ceased after the mid-fifteenth century, when ring armour was no longer attached to plate armour by such studs.

Originalwortlaut vergleichen
4.2.4.4 Bowl-pulley [ref_ill_joi_bowlpulley] 



Bowl-pulleys made of iron or copper alloy are riveted to the lower edge of some helmets of 



type-IV [ref_arm_1520] [ref_arm_1562], -V [ref_arm_2082] or -VI [ref_arm_1933] for the 



attachment of a leather or plate strap [ ref_arm_2183] carrying the ring -armour collar. The 



strap was fastened by a single wire or leather lace, led through each of the pulleys. After the 



mid-15th century, when ring -armour was not attached to armour anymore via pulleys, the 



bowl-pulleys were not produced anymore.
S. 102 · Sprachlich überarbeitet · Entwurf

4.2.4.5 Drum-shaped attachment studs

[ref_ill_joi_drumpulley] Drum-shaped studs were also used to attach ring-armour collars, continuing into the early fifteenth century [ref_arm_1655] PDF.

Originalwortlaut vergleichen
4.2.4.5 Drum-pulley [ref_ill_joi_drumpulley] 



For the attachment of the ring -armour collar, until the early 15 th century also drum-shaped 



pulleys were used [ref_arm_1655].
S. 102–103 · Sprachlich überarbeitet · Entwurf

4.2.4.6 Detachable central visor hinges

[ref_ill_joi_centralhinge] Centrally hinged face guards on Type IV [ref_arm_1564] PDF and Type V helmets [ref_arm_2023] PDF [ref_arm_2082] PDF were attached by a detachable joint. The upper leaf of the visor hinge fitted over a stud on the skull. A pivoting locking bar swung over the hinge to retain it, while a small projection at the lower edge prevented the bar from turning too far. This system ceased to be produced in the early fifteenth century.

Originalwortlaut vergleichen
4.2.4.6 Central visor-hinge [ref_ill_joi_centralhinge] 



The centrally pivoting face -guards of helmets of type -IV [ ref_arm_1564] or -V 



[ref_arm_2023] [ref_arm_2082] were fastened to the skull by a detachable joint. The upper 



side of a hinge attached to the visor fitted onto a stud on the skull. An articulated turning bolt



grabbed over the hinge for its fastening. At the lower edge a small nose prevented this bolt 



from turning over. From the early 15th century on, this system was not produced anymore.
S. 103 · Sprachlich überarbeitet · Entwurf

4.2.4.7 Hook and eye

[ref_ill_joi_hookandeye] Hook-and-eye connections are rare on armour dating from before 1500, but examples survive on the shoulder reinforcement [ref_arm_781] PDF and inside the Type III breastplates [ref_arm_3429] PDF [ref_arm_3422] PDF, where they connect the abdominal plates. The system later became common, for example for attaching thigh protection to a breastplate.

Originalwortlaut vergleichen
4.2.4.7 Hook-and-eye [ref_ill_joi_hookandeye] 



This feature is rarely to be found on armour before 1500. Nevertheless, it seems to have been 



used, as the shoulder-reinforce [ref_arm_781] is equipped with a hook-and-eye system. Also 



the abdomen-plates at the type-III breastplates [ref_arm_3429] [ref_arm_3422] are interiorly 



connected via a hook-and-eye joint. In later times this joint -type became very common, for 



example for the attachment of upper leg-protections to the breastplate.
S. 103 · Sprachlich überarbeitet · Entwurf

4.2.4.8 Rotating locking bolts

[ref_ill_joi_turninglockingbolt] A T- or r-shaped bolt is riveted to one plate, passed through the adjoining plate and rotated to lock the two together. This system attaches pelvic lames to the backplate [ref_arm_3368] PDF and is more frequently found at the junction between knee and lower-leg protection [ref_arm_2308] PDF [ref_arm_2307] PDF.

Originalwortlaut vergleichen
4.2.4.8 Turning locking-bolt [ref_ill_joi_turninglockingbolt] 



A T- or r-shaped turning bolt is riveted to one plate and led through the connected plate and 



turned for fastening. Such a system is for example found for the attachment of the pelvis -



lames to the backplate [ ref_arm_3368], but it is more frequently applied at the connection 



between knees and lower leg-protections [ref_arm_2308] [ref_arm_2307].
S. 103 · Sprachlich überarbeitet · Entwurf

4.2.4.9 Rectangular attachment fittings

[ref_ill_joi_rectangularpulley] Rectangular fittings often attach lance rests to breastplates in the Italian style. On [ref_arm_3570] PDF, the lance rest also secures a reinforcement to the breastplate. This joint developed in Italy in the early fourteenth century.

Redaktionelle Hinweise · 1
  • Die Datierung „early 14th century“ des Originals ist erhalten, auch wenn sie zur Entwicklung der beschriebenen Brustplattenbefestigungen auffällig früh erscheint. Keine stillschweigende Änderung zu 15. Jahrhundert.
Originalwortlaut vergleichen
4.2.4.9 Rectangular pulley [ref_ill_joi_rectangularpulley] 



Lance-rests on Italian-style breastplates are often attached by such a system. In the case of 



[ref_arm_3570] the lance rest also fastens the reinforce to the breastplate. This joint -type 



was developed in the early 14th century in Italy.
S. 103 · Sprachlich überarbeitet · Entwurf

4.2.4.10 Lacing holes

[ref_ill_joi_lacingholes] Armour elements could be laced to one another or to an undergarment through paired holes punched or drilled in the plate [ref_arm_611] PDF. Riveted eyelets sometimes rounded the margins of these holes to reduce wear on the laces [ref_arm_310] PDF. The eyelets could themselves be elaborately decorated [ref_arm_1797] PDF. Lacing plates to an undergarment is probably the oldest detachable fastening method.

Originalwortlaut vergleichen
4.2.4.10 Lacing-holes [ref_ill_joi_lacingholes] 



The single parts of a suit of armour could be attached to each other or to the undergarment 



by means of laces. For this purpose pairs of holes were punched or drilled into the plate 



[ref_arm_611]. To prevent the laces from chafing, the radius of the plate-edges at the lacing-



holes in some cases was enlarged by the attachment of riveted eyes [ ref_arm_310] that are 



sometimes beautifully decorated [ ref_arm_1797]. The lacing of the plate segments to an 



undergarment is probably the oldest type of all detachable fastenings.
S. 103 · Sprachlich überarbeitet · Entwurf

4.2.4.11 Screwed joints

[ref_ill_joi_screwandthread] Screws often connect the abdominal and chest plates of German Type IV breastplates [ref_arm_3625] PDF [ref_arm_4076] PDF. Contemporary images also show this construction [ref_ill_art_5218] PDF (description 2) [ref_ill_art_5219] PDF (description 2). The thread is generally cut directly into the chest plate. Screws sometimes also secure the face guards of Type VII helmets in the “black sallet” group [ref_arm_1849] PDF [ref_arm_1759] PDF. They were probably not used to connect armour elements before the mid-fifteenth century.

Originalwortlaut vergleichen
4.2.4.11 Screw and thread [ref_ill_joi_screwandthread] 



Screws are often used on German breastplates of type -IV to connect the abdomen - to the 



thorax-plate [ref_arm_3625] [ref_arm_4076]. Also artworks show this type of construction 



[ref_ill_art_5218] (descr. 2) [ref_ill_art_5219] (descr. 2). Usually the thread is cut d irectly 



into the thorax -plate. Also the face -guards of type -VII helmets of the “black sallet” group 



are sometimes fastened by a screw [ ref_arm_1849] [ ref_arm_1759]. Armour parts were 



probably not fastened by screws before the mid-15th century.
S. 103 · Sprachlich überarbeitet · Entwurf

4.2.4.12 Catches using the plate’s own spring

[ref_ill_joi_springcatch] A simple catch consists of a stud riveted near the edge of one plate and projecting through a hole in another. The plate itself supplies the spring action. From the mid-fifteenth century, this system closed the cheek plates of Type VI helmets. In the final third of the century, German armourers used it to close Type III forearm [ref_arm_546] PDF and lower-leg protection [ref_arm_2297] PDF. Two such catches could also connect foot protection to the lower-leg defence [ref_arm_2254] PDF [ref_arm_2783] PDF.

Originalwortlaut vergleichen
4.2.4.12 Spring-catch [ref_ill_joi_springcatch] 



A very simple locking -system is a bolt, riveted close to the plate edge, sticking through a 



hole in the second plate. The spring-force is provided by the plate itself. This feature is used, 



from the mid-15th century on, for the closing of the cheek -pieces at helmets of type -VI. In 



the last third of the 15 th century it was applied by the German armourers to lock the lower 



arm [ref_arm_546] and leg [ref_arm_2297] protections of type-III. Also foot protections can 



be connected to the lower leg by two spring-catches [ref_arm_2254] [ref_arm_2783].
S. 103 · Sprachlich überarbeitet · Entwurf

4.2.4.13 Spring-lock mechanism I

[ref_ill_joi_springlockmechanism I] This more elaborate mechanism occurs exclusively in the last third of the fifteenth century, fastening neck protection to a breastplate [ref_arm_3064] PDF [ref_arm_3066] PDF.

Originalwortlaut vergleichen
4.2.4.13 Spring-lock mechanism I [ref_ill_joi_springlockmechanism I] 



This sophisticated system is used exclusively in the last third of the 15th century for fastening 



a neck-protection to the breastplate [ref_arm_3064] [ref_arm_3066].
S. 104 · Sprachlich überarbeitet · Entwurf

4.2.4.14 Spring-lock mechanism II

[ref_ill_joi_springlockmechanism II] German Type VII helmet visors from the last third of the fifteenth century are generally secured by this mechanism. Pressing its button releases the face guard so that the wearer can lift it [ref_arm_1704] PDF.

Originalwortlaut vergleichen
4.2.4.14 Spring-lock mechanism II [ref_ill_joi_springlockmechanism II] 



The visor of German type-VII helmets of the last third of the 15 th century is usually locked 



by such a mechanism. The wearer can press the push -button for lifting the face -guard 



[ref_arm_1704].
S. 104 · Sprachlich überarbeitet · Entwurf

4.2.4.15 Strap staples

[ref_ill_joi_strapstaple] A staple could be fitted near the upper rear edge of a lower-leg defence. Passing the strap from the lowest knee lame through it held the two defences firmly together [ref_arm_2349] PDF.

Originalwortlaut vergleichen
4.2.4.15 Strap staple [ref_ill_joi_strapstaple] 



At the upper rear side of lower legs such a staple could be attached. The strap of the lowest 



lame at the knee protect ions was led through this staple to fasten both armour parts tightly 



together [ref_arm_2349].
S. 104 · Sprachlich überarbeitet · Entwurf

4.2.4.16 Strap slots

[ref_ill_joi_slotinplateforstrap] Early forearm [ref_arm_810] PDF [ref_arm_956] PDF [ref_arm_363] PDF and lower-leg defences [ref_arm_2309] PDF [ref_arm_2325] PDF [ref_arm_2291] PDF sometimes have a slot beside the buckle or strap attachment. It could receive a loose strap end, or allow a strap riveted inside to pass to the outside. Similar slots on the opening plates of some late fifteenth-century hand defences probably received loose strap ends [ref_arm_1207] PDF. On the backplate [ref_arm_3417] PDF, internally riveted waist straps passed out through slots.

An image of a fallen combatant [ref_ill_art_5249] PDF (description 1) shows one-piece leather arm defences that do not fully enclose the arm, closely resembling [ref_arm_5103] PDF [ref_arm_5104] PDF. Their straps appear to pass in from outside, with T-shaped ends preventing them from pulling through the slots. Slots in later metal defences therefore very probably derive from earlier leather protection.

Originalwortlaut vergleichen
4.2.4.16 Slot in plate for strap [ref_ill_joi_slotinplateforstrap] 



At early armour for the lower arm [ ref_arm_810] [ ref_arm_956] [ref_arm_363] and leg 



[ref_arm_2309] [ref_arm_2325] [ref_arm_2291] sometimes a slot pierces the plates next to 



the buckle- or strap-joint. Either the strap end was stuck through this hole or the strap was 



riveted here interiorly and led through the hole to the outside. The flaps of some late 15 th 



century hand-protections also show such slots [ref_arm_1207], probably the strap-ends were 



stuck through these holes. At the backplate [ ref_arm_3417] the waist -straps were riveted 



interiorly and led through slots. An illustration of a fal len fighter [ref_ill_art_5249] (descr. 



1) shows leather protections for the arms. They consist of one part only, do not close 



completely and are very similar to the extant examples [ ref_arm_5103] [ ref_arm_5104]. 



Here it also seems like the leather straps for the fastening had been stuck from the outside, 



prevented from slipping through the sl ots by a t -shaped ending. Therefore, it is very likely 



that the slots in the plate of later defenses derive from early leather-protections.
S. 104 · Sprachlich überarbeitet · Entwurf

4.2.4.17 Removable leather straps

[ref_ill_joi_detachablestrap] Many objects may have lost their straps and buckles because these were attached by a buttonhole-like slit slipped over a Type a rivet [ref_vid_mushrivet]. The rivet must stand slightly proud of the plate, leaving space beneath its broad head and resembling a small mushroom.

The surviving straps described here as connecting elbow and forearm protection on [ref_arm_1564] PDF, and the rivets at the shoulder ends of the breastplate [ref_arm_3522] PDF, use this arrangement. It allows components to be detached quickly and worn leather to be replaced easily.

Redaktionelle Hinweise · 1
  • Die Referenz ref_arm_1564 ist im selben Kapitel einem Helm zugeordnet. Ihre Verwendung für eine Ellenbogen-Unterarm-Verbindung stammt aus dem Original und ist noch zu klären; keine andere Objekt-ID eingesetzt.
Originalwortlaut vergleichen
4.2.4.17 Detachable leather-strap [ref_ill_joi_detachablestrap] 



One explanation why many objects retain no leather straps or buckles might be that the straps 



were attached by a buttonhole -like slit, clipped into a rivet of type -a [ref_vid_mushrivet]. 



This rivet has to be fixed to the plate with a small space between the head and the plate 



surface, looking like a growing mushroom. The extant leather straps connecting the elbow 



to the lower arm at [ ref_arm_1564] and the rivets remaining at the shoulder -ends of the 



breastplate [ ref_arm_3522] are designed this way. This system allows a quick and easy 



detachment of the single parts and for a simple replacement of fragile leather.
S. 104–107 · Sprachlich überarbeitet · Entwurf

4.2.4.18 Straps and buckles

[ref_ill_joi_strapandbuckle] Armour must be secured either to the wearer or to other armour elements. Buckles—usually called “ringen” in medieval sources128—have an important but little-studied role in its design and use. Armourers could readily make them themselves, but could also purchase them from specialist buckle-makers, the “Rinckenschmied” [ref_ill_art_5321] PDF.

Only one article appears to focus specifically on armour buckles.129 Ilse Fingerlin’s study is probably the most comprehensive account of medieval belts more generally.130 Close connections can be expected between contemporary belts and armour straps.

Surviving buckle attachments are difficult to assess. Most buckles have been lost, and those that remain are not necessarily original131 or contemporary with the armour’s manufacture. They are wearing components, exposed to abrasion during use, and could easily be torn away when attached directly to leather. They are also readily copied: a metalworker needs only thick sheet and a file to reproduce a simple form, while a mould taken from an original permits cast copies.

Establishing reliable reference examples was therefore difficult. The CH and HJRK collections offered promising starting points because the relevant armour has exceptionally good provenance. Contemporary images sometimes show straps and buckles in sufficient detail to support comparisons [ref_ill_art_5335] PDF (description 3).

Armour buckles are made from iron or copper alloys; some copper-alloy examples may have been gilded.132 Two basic forms occur,133 both still used for other purposes today, although their designs have changed. The first has a single frame. Its outline may be rounded, as in probably original examples on [ref_arm_1135] PDF [ref_arm_1228] PDF [ref_arm_1272] PDF, or square, as on the forearm pair [ref_arm_810] PDF [ref_arm_986] PDF, where originality is probable, and on [ref_arm_1341] PDF [ref_arm_3898] PDF, where it is certain.134 Rectangular and trapezoidal examples may be original on [ref_arm_88] PDF [ref_arm_2376] PDF [ref_arm_3382] PDF. This form is termed a “single-frame buckle” below.

The second form has two openings, essentially arranged as a figure of eight [ref_ill_art_5352] PDF [ref_arm_3796] PDF, but sometimes given a rectangular outline [ref_arm_3423] PDF [ref_ill_art_5359] PDF. Other variants combine a rounded, drop-like end with a square one [ref_arm_3795] PDF. The term “double-frame buckle” corresponds closely to the “boucles doubles” mentioned in a French document of 1446 for fastening body armour.135 The second opening retains the loose strap end, making it less obtrusive than on a single-frame buckle.

Either form may have a small roller or tube on one side to reduce strap wear and make a tight strap easier to release. Probably original single-frame examples occur at the front of [ref_arm_3795] PDF [ref_arm_3861] PDF, and a double-frame example on [ref_arm_3704] PDF. A contemporary depiction confirms their use by the second half of the fifteenth century [ref_ill_art_5168] PDF.

Some buckle forms remained in use for so long that precise dating is difficult. A mould for rounded double-frame buckles, dating from before 1284, was excavated with other moulds in Magdeburg in 2005.136 Comparable buckles were among the finds recovered in 1961 from the Swedish warship Vasa, which sank in 1628; they are displayed in Stockholm’s Vasa Museum.

Buckle plates often have filed edge decoration, and sometimes chiselled or engraved surface patterns [ref_arm_1228] PDF [ref_arm_1272] PDF. Some simple brass buckles were shaped by filing rather than casting [ref_arm_2294] PDF. Since iron could not be cast finely enough before the nineteenth century, iron examples must have been cut or forged [ref_arm_4926] PDF.

Apparently, any contemporary buckle form could serve on armour. A possible regional preference is for rounded forms in German-speaking regions and trapezoidal forms in Italy. The same buckles occur on other contemporary equipment.137 Fingerlin’s drawings of presumed belt or purse buckles [ref_ill_art_5378] PDF, compared with armour buckles in contemporary art [ref_ill_art_5179] PDF, make this clear. Metal strap ends also appear frequently [ref_ill_art_5290] PDF (description 2) and probably differed little from those used elsewhere.

More expensive armour might be expected to have more elaborate buckles. Some of the finest objects of the period were made by Lorenz Helmschmied in Augsburg, and most survive in the HJRK in Vienna. Unfortunately, their buckles do not permit secure conclusions about contemporary designs. The fastenings on [ref_arm_3257] PDF138 have been so extensively restored that most buckles are reproductions,139 with Renaissance or even Baroque rather than medieval forms.

The same buckles occur on the pair of hand defences [ref_arm_1208] PDF [ref_arm_1246] PDF, which were formerly displayed with that suit.140 Their uniformity suggests that nineteenth-century restorers may have cast copies of a sixteenth- or seventeenth-century model to unify the assembled armour.141 The same large rectangular double-frame buckles appear even where smaller examples would be expected, such as at the forearm or shoulder.

Originalwortlaut vergleichen
4.2.4.18 Strap and buckle [ref_ill_joi_strapandbuckle] 



Armour needs to be fastened – either to the wearer’s body or to other armour parts. Buckles 



– in the Middle Ages usually called “ringen”128 – play an important but yet unattended role 



in the design and practical use of armour. While the armourer could easily have made them 



on his own, he could also have bought them in from a specialized craftsman, the so called 



“Rinckenschmied” [ref_ill_art_5321].  



Until now scholars of armour did not pay much attention to this important part of fastening 



systems. Only one article focusing particularly on armour -buckles seems to exist. 129



Probably the most comprehensive study of medieval belts in general was published by Ilse 



Fingerlin.130 It can be anticipated that there are a lot of links between contemporary medieval 



belts and the straps on armour. 



It is not easy to examine the buckle -fastening on extant armour. In most cases the buckles 



are lost. Those which survive are not necessari ly genuine131 – or at least they do not date 



from the production-time of the armour. Buckles belong to the wearing-parts of armour. As 



long as the item was used, they were exposed to abrasion. If they were riveted directly to 



leather straps, they got easily torn and lost. Another problem is that they can easily be copied. 



A piece of thicker plate and a file is enough for any metalworker to copy simple shaped 



examples. The cast buckles can easily be copied by making a mold of the original. 



Nevertheless, a few aspects on buckles on extant armour will be discussed below. A problem 



for a discussion was to find a reliable reference for definitely genuine examples. The 



collections of CH and the HJRK were considered good places to start from, as the concerned 



armour parts preserved in these collections are of the best provenances. Comparisons to 



contemporary artworks might be helpful. They sometimes illustrate straps and buckles at 



armour in details [ref_ill_art_5335] (descr. 3). 



Buckles on armour are either made of copper alloys or of iron. Some of the copper alloy 



examples might have been gilded. 132 There are two basic types of buckles found on 



armour.133 Until today these two types are still in use for different purposes – just the design 



may be different from the medieval ones. The first type consists of one frame only. The shape 



of this type varies from rounded (probably genuine at [ ref_arm_1135] [ ref_arm_1228] 



[ref_arm_1272] and square (probably genuine at the pair of lower arms [ ref_arm_810] 



[ref_arm_986] and certainly genuine on [ ref_arm_1341] [ref_arm_3898])134 to rectangular 



or trapezoid (original m aybe at [ ref_arm_88] [ ref_arm_2376] [ ref_arm_3382]). Such 



examples will be called a “single-frame” buckle in further notes. 



The second type consists of two frames, basically in the shape of an “8” [ ref_ill_art_5352] 



[ref_arm_3796], which could be  abstracted into a rectangular shape [ ref_arm_3423] 



[ref_ill_art_5359]. Also variations resembling a combination of drop- and square shapes do 



exist [ref_arm_3795]. This type will be called the “double-frame” buckle. The term is similar 



to the contemporary one, as a French source of 1446 mentions “boucles doubles” 135 for the



fastening of body-armour. The double-frame buckles have a remarkable advantage over the 



single-frame type: The strap -end can be conducted through the second frame and thus it is 



less bothering than the free-moving end of a strap fastened by a single-frame buckle. 



Both types can have a small roll or tube at one side, which would ease the opening of a tight 



strap and reduce its wear. A probably original single-frame example is found at the front of 



[ref_arm_3795] [ref_arm_3861] and a double frame is found at [ ref_arm_3704]. That such 



buckles – still produced today – were definitely in by the second half of the fifteenth century 



can be seen on [ref_ill_art_5168]. 



How difficult it is to exactly date some models shows the obviously large timeframe in which 



the round -shaped double-frame buckles were used: In 2005, in Ma gdeburg together with 



several others a mold for such buckles from before 1284 136 was excavated. In 1961 on the 



“V asa”, a Swedish war-ship that sank in 1628, several of such buckles were discovered 



within numerous other finds. They are exhibited in the V asa-Museum in Stockholm. 



The holder-plates of the buckles were often decorated by filings at the edges, some also had 



chiseled or engraved patterns on the surface [ ref_arm_1228] [ref_arm_1272]. Some simple 



brass buckles were made rather by filing than by casting [ref_arm_2294]. As iron could not 



be cast delicately enough before the 19 th century, all the iron buckles must have been made 



by cutting or by forging [ref_arm_4926]. 



It seems like any contemporary type of buckle could serve for the fastening of armour. The 



only difference is maybe found between armour made in the German speaking lands, where 



rounded types are favored, and armour made in Italy, where the trapezoid shape seems to 



have been preferred. 



Buckles found on armour can be found at other contemporary non-armour objects as well.137 



This becomes clear when some of Fingerlin’s drawings of presumably belt or purse-buckles 



[ref_ill_art_5378] are compared to buckles on armour in art [ref_ill_art_5179]. Often metal-



strapends can be seen [ ref_ill_art_5290] (descr. 2). They did probably also not differ much 



from examples attached to non-armour objects. 



On more expen sive items, the buckles are expected to be decorated more elaborately. The 



most delicate armour parts of the considered period are certainly those made by Lorenz 



Helmschmied of Augsburg, most of which are preserved in the HJRK in Vienna. 



Unfortunately, the studies of the buckles on the items in this collection do not allow any 



reliable conclusions on contemporary designs. The fastenings on the suit [ref_arm_3257]138 



had been restored so extensively that most of the buckles are reproductions 139; they are not 



medieval in style, but rather renaissance or even baroque. At the pair of hand -protections 



[ref_arm_1208] [ref_arm_1246], the same buckles as on suit [ref_arm_3257] can be found. 



This pair of hand -protections has been attached to this suit at previous installations. 140 As



the considered buckles all look the same, it is well possible that in the 19th century they were 



cast from an original of the 16th or 17th century to reveal a uniform appearance of the armour 



parts assembled to one suit.141 Even where smaller examples are expected, e. g. at the lower 



arms or at the shoulder, the same large rectangular double-frame buckles are attached.
S. 107 · Sprachlich überarbeitet · Entwurf

4.2.4.19 Crest attachments

Type II helmets were the first to carry heraldic crests: three-dimensional devices laced to the skull. A few survive, including the painted leather crest on [ref_arm_1488] PDF.

Nearly all Type V and VII helmets have a hole at the crown. On Italian Type V helmets, it is usually keyhole-shaped. These openings most probably secured crests, whose possible appearance is shown in contemporary art [ref_ill_art_5187] PDF. The fastening method is uncertain. Few contemporary crests survive,142 and I was unable to examine one in person.

An iron “stick” associated with the Type VI helmet [ref_arm_1932] PDF has traditionally been interpreted as a crest support.143 It is much more likely to be a sixteenth-century gun-barrel cleaning tool. A thread at one end would screw into a cleaning rod, while springs at the other maintained close contact with the bore. A comparable object in the Graz Zeughaus is identified as a cleaning implement.144 The Churburg object also fits the helmet opening poorly. If it had served as a crest support, a simple round hole would have sufficed; the keyhole shape would be unnecessary.

The actual fastening may have been simpler. A threaded lower end on the crest could have screwed into a nut inside the skull. A small projection on the nut may have engaged the narrow part of the keyhole, preventing rotation and allowing the crest to be fitted or removed without tools.

Originalwortlaut vergleichen
4.2.4.19 Crests 



Helmets of type -II were the first helmets to be surmounted by a heraldic application, a so 



called “crest”. At these helmets, a three dimensional symbol was laced to the skull. A few 



examples still exist, for instance the painted leather crest on the type -II helmet 



[ref_arm_1488]. 



The center of the skull of nearly all type-V and -VII helmets is pieced by a hole. On Italian 



helmets of type-V it usually has the shape of a keyhole. Most likely these holes served for 



the mounting of a crest. Artworks show what they could have looked like [ref_ill_art_5187]. 



It is not clear how the joint actually worked. Only few contemporary crests for such helmets 



are extant142, unfortunately the author was unable to examine any example in person.  



To the type-VI helmet [ref_arm_1932] an iron “stick” is attributed, traditionally considered 



to be a base for a crest 143. This item is most likely rather a 16 th century tool for the interior 



cleaning of a gun-barrel. The thread at the one side was screwed  to the cleaning-stick. The 



springs at the other end ensured a precise cleaning due to close fit to the interior surface of 



the barrel. A comparable object is preserved in the Zeughaus in Graz144, there it is attributed 



to the aforesaid function. The Churburg item does also not really fit to the hole in the skull 



of the attributed helmet. Furthermore, the keyhole in the helmet’s skull would not be 



necessary, a simple hole would be sufficient if the item was actually meant to hold a crest. 



The attachment of crests might have been simpler. It probably had a threat at its lower end 



and was fastened by turning into a nut at the interior of the skull. This nut maybe had a small 



nose that grabbed into the key -bit of the hole and thus no tool was needed to mount or 



dismount the crest.
S. 107–108 · Sprachlich überarbeitet · Entwurf

4.2.5 Fastening armour to the body

Examining armour requires asking how it was secured to the wearer. This important question has long received little attention. Tobias Capwell’s detailed 2002 article on Italian “arming doublets” approaches it through visual evidence.145 The following discussion instead examines surviving objects for evidence of their original fastening arrangements.

Surviving fastenings do not necessarily date from manufacture. Organic components must generally be assumed to have been replaced during an object’s lifetime. Many apparently purposeless holes once held rivets securing leather, textile or other attachments. These holes can reveal how an armourer intended an object to be worn and to function.

Contemporary images throughout the early period of plate armour show it worn both over and under clothing. Albrecht Dürer depicts one arrangement in [ref_ill_art_5355] PDF: a man-at-arms wears his breastplate and hand protection beneath a slashed jacket, with shoulder and elbow defences outside the garment. Another image shows a rider with a jacket over his breastplate and arm defences over the jacket [ref_ill_art_5383] PDF. The relationship between armour and clothing has not yet been studied systematically. The following observations suggest some possibilities.

Originalwortlaut vergleichen
4.2.5 Body-fastenings 



One of the questions to be attended whenever armour is examined is on the way it was 



fastened to the wearer’s body. This important approach has long been neglected by scholars 



of the subject. In 2002 Tobias Capwell wrote a detailed article on Italian “Arming -



Doublets”145. He approaches this topic from the iconographical illumination of armour -



fastenings, while the following considerations examine existing armour on the question of 



its former fastening.  



Fastening-features on extant armour do not necessarily derive from the time when the armour 



left the workshop. In most cases it has to be assumed that attached organic material has been 



replaced throughout the lifetime of an armour -part. On many armour pieces, holes without 



any obvious purpose can be found. They were once filled by rivets which were holding 



organic parts or other applications. Many of the functionless holes can tell details about the 



intensions of the armourer and the way an armour part once worked.



Throughout all the early plate armour period, on contemporary artworks it can be observed 



that armour was optionally worn upon or underneath the clothing. Albrecht Dürer depicted 



one interesting possibility how armour could be combined with the textile clothing 



[ref_ill_art_5355]. A man-at-arms wears his breastplate and his hand-protections underneath 



a slit jacket, while his shoulder defenses and the elbows are fastened on top of the 



undergarment. In  another of his works he shows a rider wearing his jacket upon the 



breastplate and the arm-defenses upon the jacket [ref_ill_art_5383]. The interaction between 



armour and clothing has not been the subject of any study yet. A few observations will be 



discussed in the following.
S. 108–110 · Sprachlich überarbeitet · Entwurf

4.2.5.1 Securing breastplates

Nearly all breastplates from the period examined have very narrow waists.146 This was certainly more than a matter of fashion. A belt holding the armour closely at the waist transferred much of its weight away from the shoulders. The soft area between the ribs and the hip bones could be compressed without intolerable discomfort, comparable to the effect of nineteenth-century women’s corsets. The resulting rigid shell also allowed more room around the chest, easing breathing.

Torso protection in the Italian system is less readily adjustable in circumference than its German counterpart. Hinges on one side prevent the front and back plates from overlapping further there; only the buckled straps on the opposite side permit a small range of adjustment. Tightening them too far makes the assembly asymmetrical and compresses the wearer on the buckled side. Some adjustment was essential to accommodate changes in body size and garments of different thickness, for example in different weather.

Since an Italian abdominal plate could not be tightened indefinitely around the waist, it had to be suspended by buckles from the chest plate. Front-and-back torso protection in this system consequently placed more weight on the shoulders, and its waist was generally less constricted than in the German system. The abdominal plates effectively hung from the chest plates. Italian front and back plates almost meet over the shoulders, probably to distribute this load over a broader area [ref_ill_art_5375] PDF.

The fastening of breastplates worn without backplates is often difficult to reconstruct: no original back straps survive. On reproductions I made, straps were riveted near the edges below the arm openings, crossed behind the wearer, and buckled to the shoulder ends of the breastplate. During this study, however, it became clear that most surviving breastplates from the second half of the fifteenth century could not have used this arrangement: they lack the necessary rivet holes below the arm openings. This raises the question of how they were secured.

Contemporary images must be examined closely for possible answers. Rear views of combatants are rare. Some show no breastplate straps at all [ref_ill_art_5150] PDF; others lack sufficient detail to establish their arrangement [ref_ill_art_5305] PDF. In a few, straps appear to be riveted below the arm openings [ref_ill_art_5174] PDF. More than one system evidently existed.

The painting [ref_ill_art_5306] PDF (description 2) offers the clearest explanation for the usual absence of lower attachment holes. Its battlefield includes discarded breastplates whose straps form an X and are visibly attached only at the shoulders. Another image suggests how this system looked when worn [ref_ill_art_5345] PDF.

It was most probably closed with a single buckle at the front of the waist, readily accessible to the wearer [ref_vid_puttingonabreastplate]. The straps tend to ride upwards along the plate’s sides. Deep waist cut-outs on many later fifteenth-century breastplates may have prevented this [ref_arm_3701] PDF [ref_arm_3750] PDF [ref_arm_3421] PDF [ref_arm_3429] PDF. Alternatively, the cut-outs may have made an underlying ring-armour shirt more comfortable while retaining a narrow waist. They appear in images from the 1470s [ref_ill_art_5369] PDF [ref_ill_art_5207] PDF and become common by the early sixteenth century [ref_ill_art_5177] PDF.

Related arrangements may have addressed the same problem. The buckle in [ref_ill_art_5246] PDF was probably less accessible, but rings on either side of the waist prevented the straps from riding upwards. Several similar Type II breastplates in the WM have a buckle fitted directly to the left side of the plate at the waist [ref_arm_3528] PDF [ref_arm_3529] PDF.

Such arrangements made shoulder buckles optional. Straps could be permanently riveted to the plate or attached by a slit fitted over a mushroom-headed stud [ref_vid_mushrivet]. This may explain why so many simple front torso defences lack shoulder buckles. Leather becomes brittle over time. Removable straps could be stored and maintained separately, then issued when soldiers prepared for combat. This would have been particularly practical for arsenal armour, since maintaining hundreds of objects was difficult and expensive.

Putting on a complete suit of armour was a lengthy process requiring the help of squires or servants [ref_ill_art_5364] PDF. It was therefore important that the wearer could release it unaided in an emergency. A passage in Maximilian I’s Weiskunig illustrates this concern:

[…] Derer zu ainer zeit, Rit der Jung weiß kunig [Maximilian I.] in 



ainen großmechtigen streit, und als Er seinen ganntzn kiriß, und 



vechtharnasch anleget, da wolt sein wappenmaister , Ime das 



hauptharnasch, mit schraufen wol versorgen, damit die veindt Ime das 



nit aufschlagen mochten, Da fragt der kunig den wappenmaister , welches 



pesser were, den gewalt in seinder handt, oder in aines anndern hanndt, 



der wappenmaister gab anntwurt, welcher gewalt hat, der ist herr , da 



saget der kunig, Darumb so will Ich des harnasch geweltig sein, und mit 



der öffnung, des hauptharnasch, nit in deinen willen leben, wiewol du 



mir sölichs zu ainem gueten thuest, waist du aber nit, das aus 



unbetrachter oder unbesynndter guethaidt, vil laidt komen, Aus dem mag 



ain Jeder versteen, das dis kunig gewest ist, ein lerer unnd offenbarer , 



anndern kunigen, in der harnaschmaisterey und wappenmaisterey […]
Treitzsaurwein (1775), pp. 97–98; original quotation and the dissertation’s translation in note 147. 147

Control over fastenings mattered to infantry as well as mounted men-at-arms. Requiring every defender of a town to find help fastening shoulder buckles would have delayed mobilisation. In danger, a soldier might also need to discard his armour quickly to escape.

Redaktionelle Hinweise · 2
  • Die Aussagen zur Lastverteilung, Taillenkompression und Atmung sind Hypothesen bzw. technische Aussagen der Dissertation, keine neu überprüften ergonomischen Ergebnisse.
  • Der Originalabsatz verallgemeinert von fehlenden unteren Befestigungslöchern auf sämtliche einzeln getragenen Brustplatten dieser Zeit. „Most surviving breastplates“ bindet die Aussage hier an die ausdrücklich genannte Beobachtungsgrundlage; alternative Systeme bleiben im folgenden Absatz erhalten.
Originalwortlaut vergleichen
4.2.5.1 The body-fastening of breastplates 



The waists of nearly all breastplates of the considered period are very narrow 146. This has 



certainly not only been a matter of fashi on aspects, but moreover this had a very practical 



task to fulfill. To keep the largest part of the weight away from his shoulders, with the help 



of a belt a tight fastening was set up at the waist of the wearer. The body region between the 



rips and the hip-bone is so soft that it can be tapered without causing unbearable pain, similar 



to the 19th century corselets in female fashion. By this “shell”, the wearer got more space for 



motion at his chest, which eased the breathing.  



With torso plates of the Italian system, the circumference is not as easily adjustable as at the 



plates of the German System. The hinges at the one side do not allow the backplate 



overlapping further with the breastplate. Only the buckled leather straps at the opposite side 



can be adjusted in stages in a narrow range. Much adjustment is not possible, as the system 



gets out of symmetry, resulting in the squeeze of the wearer’s body at the buckled side. A 



little range is always necessary, as the body-measurements of the wearer could chan ge, but 



also – depending e. g. on weather conditions – garments with different thicknesses could be 



worn underneath. As the abdomen -plate of the Italian system could not be unlimitedly 



tightened around the waist, for holding it in its position it needed to  be buckled upwards to 



the thorax-plate. The wearer of a torso front and back -protection constructed in the Italian 



system had to carry more weight on his shoulders. The waist of these protections is usually 



not as tapered as at examples of the German syst em. The abdomen plates are “hanging” 



buckled to the thorax-plates. Probably to spread the weight on a larger surface, the front- and 



backplate on Italian armour nearly touch at the shoulders [ref_ill_art_5375]. 



The former fastening -system of single -worn breastplates can often not easily be 



reconstructed. No genuine back -straps survive at extant armour. The author has made 



himself some reproductions of armour. The back -straps of breastplates in these cases were 



riveted close to the plate edge underneath the arm-cutouts. To fix the plate to the body, these 



straps were crossed at the wearer’s back and then attached to a buckle at each shoulder -end 



of the breastplate. In the course of this study  it became clear that single breastplates of the 



second half of the 15 th century cannot have been worn with such a strap system, as most 



extant examples do not show holes under the arm-cutouts for the riveting of the back-straps. 



This raised the question on how these breastplates were actually fixed to the wearer’s body.  



The detailed examination of several artworks is necessary to reconstruct how the original 



fastening might have worked. Illustrations of the backs of fighters are rare. In several cases 



no breastplate-fastening straps are visible at all [ ref_ill_art_5150]. Other depictions are not 



detailed enough to allow the understanding of the back-strap system [ref_ill_art_5305]. In a 



few cases the straps seem to be actually riveted to the plate under the arm cutouts 



[ref_ill_art_5174]. Obviously different systems existed.



The painting [ref_ill_art_5306] (descr. 2) delivers the best explanations on the question why 



usually no holes for the back-straps are visible at extant plates. In the painting, the battlefield 



is covered by fighters in combat, bodies and arms. Breastplates are lying scattered on the 



ground. The straps of the breastplates are forming an “X”, clearly only attached to the 



shoulder-edges. What the system might have looked l ike when worn can be seen at 



[ref_ill_art_5345].  



This system was most likely fastened at the frontal waist by a single buckle – easily 



accessible for the wearer himself [ ref_vid_puttingonabreastplate]. The straps tend to slide 



upwards along the sides of the plate. Probably to avoid this effect, the plates of many 



breastplates of  the second half of the 15 th century were deeply cut out at the waist 



[ref_arm_3701] [ ref_arm_3750] [ ref_arm_3421] [ ref_arm_3429]. It is also possible that 



they were meant to make the wear of a ring-armour shirt underneath more comfortable, while 



still forming a lean waist. These cutouts are already found at ar tworks of the 1470ies 



[ref_ill_art_5369] [ref_ill_art_5207] and they become common by the early 16 th century 



[ref_ill_art_5177]. Probably due to this problem, also other, similar systems were developed. 



The buckle at [ ref_ill_art_5246] was probably a bit difficult to reach, but the straps could 



not slide upwards as they were conducted through a ring at each side of the waist. Many 



similar type-II breastplates in the WM have a buckle attached directly to the plate at the left 



side of the waist [ref_arm_3528] [ref_arm_3529].  



This system makes buckles at the shoulder-edges optional. The straps could also be riveted 



permanently to the plate or the y might have been attached via a slit in the leather that was 



clipped to a “mushroom” rivet [ref_vid_mushrivet]. This could explain why so many simple 



front torso -protections do not have buckles attached to the shoulder -edges. Within time, 



leather becomes brittle. If the straps were buckled or clipped at the shoulders and not 



permanently riveted to the plate, they  could be kept and maintained separately from the 



plates and given to the soldiers when they got prepared for combat. Especially for arsenal -



armour this arrangement makes sense, as the permanent maintaining of hundreds of objects 



was a difficult and expensive task. Simplifications were certainly welcome.  



Getting dressed in full armour was a long procedure that could not be achieved by the wearer 



himself. Several squires or servants were necessary to fasten all parts to their place 



[ref_ill_art_5364]. It was therefore very important to take care that, in case of emergency, 



the fighter could get rid of his armour by himself. A passage in Maximilian I.’s “Weiskunig” 



may serve as an illustrative proof for this necessity:



[…] Derer zu ainer zeit, Rit der Jung weiß kunig [Maximilian I.] in 



ainen großmechtigen streit, und als Er seinen ganntzn kiriß, und 



vechtharnasch anleget, da wolt sein wappenmaister , Ime das 



hauptharnasch, mit schraufen wol versorgen, damit die veindt Ime das 



nit aufschlagen mochten, Da fragt der kunig den wappenmaister , welches 



pesser were, den gewalt in seinder handt, oder in aines anndern hanndt, 



der wappenmaister gab anntwurt, welcher gewalt hat, der ist herr , da 



saget der kunig, Darumb so will Ich des harnasch geweltig sein, und mit 



der öffnung, des hauptharnasch, nit in deinen willen leben, wiewol du 



mir sölichs zu ainem gueten thuest, waist du aber nit, das aus 



unbetrachter oder unbesynndter guethaidt, vil laidt komen, Aus dem mag 



ain Jeder versteen, das dis kunig gewest ist, ein lerer unnd offenbarer , 



anndern kunigen, in der harnaschmaisterey und wappenmaisterey […]147 



Not only for the knightly riders, but also for foot-soldiers it was important that they were in 



control of their armour. If each of the defenders of a medieval city in case of alert would 



need a helping hand to buckle their breastplates at the shoulders, the war would permanently 



have been over before the first soldier left the arsenal. In danger it was possibly necessary to 



get rid of the armour in a short time and to escape quickly.
S. 110–111 · Sprachlich überarbeitet · Entwurf

4.2.5.2.1 Type III

Several contemporary images show breastplates without plate protection for the pelvis [ref_ill_art_5236] PDF [ref_ill_art_5255] PDF (description 1), or worn with skirts of ring armour [ref_ill_art_5273] PDF or segmented armour [ref_ill_art_5272] PDF (description 1). A wall painting of St George fighting the dragon [ref_ill_art_5274] PDF shows the ring-armour skirt at the front of the pelvis secured independently by a leather belt. Under the typology used here, breastplates without attached pelvic protection would belong to Type I.

Images from German-speaking regions between the 1420s and 1450s often show breastplates laced to the undergarment at the shoulders [ref_ill_art_5266] PDF [ref_ill_art_5211] PDF (description 1). Straps also seem to have been used during the same period [ref_ill_art_5259] PDF. Shoulder attachments are readily understood; fastening at the waist is generally less clear. This question may help explain a feature of many surviving Type III breastplates.

On some examples, the abdominal and chest plates meet at a single central rivet [ref_ill_art_5197] PDF, buckle [ref_ill_art_5215] PDF, hook-and-eye joint [ref_arm_3429] PDF [ref_arm_3422] PDF, or bolt-and-eye joint [ref_arm_3621] PDF [ref_arm_3624] PDF.148 Detachable connections must have served a purpose. They may simply have allowed the lower plates to be removed for transport. Alternatively, the breastplate may sometimes have been worn without the abdominal and pelvic plates, perhaps substituting a ring-armour skirt for comfort on long rides or marches. Yet the surviving objects lack holes for securing the abdominal plates at the waist, so this interpretation remains uncertain. A waist belt might have attached to the internal fitting at the lower edge of the chest plate.

Another possibility is that apparently absent abdominal and pelvic plates were concealed beneath a jacket skirt for reasons of fashion.149 The stud or fitting joining the plates could then have passed through a slit or hole in the garment [ref_vid_wearingtf-III].150 Early examples with shoulder lacing holes could readily have been worn this way.

Later examples with detachable abdominal plates appear to have used back straps. Since the chest plate needed support at the shoulders, both back straps and a waist belt would necessarily have remained visible. No contemporary depiction shows this arrangement. It therefore remains uncertain whether combining armour with clothing explains the detachable chest-to-abdomen connection.

Originalwortlaut vergleichen
4.2.5.2.1 Type-III 



Several contemporary depictions show breastplates worn without a pelvis protection 



[ref_ill_art_5236] [ ref_ill_art_5255] (descr. 1) or together with a skirt of ring - 



[ref_ill_art_5273] or segment -armour [ ref_ill_art_5272] (descr. 1). A wall painting, 



depicting St. George fighting the dragon [ ref_ill_art_5274], show s that the ring -armour 



protection for the front of the pelvis is fastened completely independent from the breastplate 



by a leather strap around the knight’s waist. These breastplates, according to the type-system 



defined above, would be considered as type-I. 



Artworks made between the 1420ies and the 1450ies in the German speaking lands often 



show that breastplates at the shoulders were laced to the undergarment [ ref_ill_art_5266] 



[ref_ill_art_5211] (descr. 1), but also a strap -system seems to have been used in the same 



period [ref_ill_art_5259]. While the shoulder fastening is easily understandable, it is usually 



less obvious how the plates were fastened to the waist. The development of an important 



feature of many extant type-III breastplates might be connected to this fastening question.  



The abdomen-plate at some type-III breastplates is fastened to the thorax-plate by either one 



central rivet [ ref_ill_art_5197], buckle [ ref_ill_art_5215], hook -and-eye [ ref_arm_3429]



[ref_arm_3422] or bolt -and-eye joint [ ref_arm_3621] [ ref_arm_3624].148 The armourer 



certainly had some intention when he applied these detachable joints. The simplest 



explanation might be that for transport the lower plates could be dismounted. Another 



assumption is that such breastplates might optionally have been worn without the abdomen- 



and the pelvis -plates or they could optionally be replaced by a skirt of ring -armour – for 



example for the ease of long rides or marches. As the extant examples show no holes for a  



fastening of the abdomen-plates to the waist, it is not sure that these breastplates could have 



been used this way. The only possibility is that a waist -belt was connected to the interior 



pulley at the lower edge of the thorax-plate. 



A further explanation is that where no pelvis-lames are visible in depictions, the abdomen - 



and the pelvis-plates were worn invisible underneath the skirt of a jacket – for fashion reason 



only.149 To join the abdomen-plate, the pulley or stud of the joint was then stuck through a 



hole or slit in this garment [ref_vid_wearingtf-III]150. Only early examples with lacing holes 



at the shoulders could easily have been fastened this way. The extant later ite ms with 



detachable abdomen-plates seem to have had back straps. The thorax-plate would have to be 



fastened to the body at the shoulders and therefore the back -straps and a waist -belt would 



necessarily be visible. No contemporary depiction shows such a cons truction. Therefore, it 



is not sure that the clothing-combination was the reason for the application of the detachable 



joint between the thorax and the abdomen-plate.
S. 111–113 · Sprachlich überarbeitet · Entwurf

4.2.5.2.2 Type IV

As suggested above, the abdominal plate of Type IV breastplates may have developed from an upward extension of the adjoining first pelvic lame. Its central point may imitate a contemporary craftsman’s apron [ref_ill_art_5300] PDF [ref_ill_art_5301] PDF (description 2) [ref_ill_art_5302] PDF [ref_ill_art_5365] PDF. Like an apron, the abdominal plate was sometimes worn over clothing with no chest plate visible. Several images, chiefly Burgundian, show it over a jacket [ref_ill_art_5294] PDF or a ring-armour shirt [ref_ill_art_5287] PDF. Comparable arrangements appear elsewhere in Europe [ref_ill_art_5281] PDF. In [ref_ill_art_5338] PDF, only the abdominal plate is visible, without pelvic protection. Contrasting colours between upper and lower plates were evidently fashionable: the chest plate could also be covered with leather or textile [ref_ill_art_5164] PDF.

How were the apparently separate abdominal plates in these images secured? A waist belt may have sufficed, but without an upper fastening the point would probably stand away from the chest. The original argument also questions why a combatant would leave the chest exposed when the rest of the body was well protected. That question motivates the reconstruction below; the absence of a visible chest plate does not itself establish whether one was worn.

Surviving constructional features offer clues. On many Type IV breastplates, particularly those probably made in German-speaking regions, a single screw connects the two main plates. Its thread is usually cut directly into the chest plate. The hole appears to have been punched from outside with a pointed tool. Since the plate alone might be too thin for enough thread turns [ref_arm_3630] PDF, the displaced metal forms an inward-projecting cone that provides greater depth. Making a screw and matching thread demanded time and skill. Why, then, did the armourer not simply rivet the plates together?

Many such breastplates have up to three vertically arranged positioning holes inside [ref_arm_3679] PDF, perhaps to adjust overall length for wearers of different heights. Another possibility is that the screw allowed the plates to pivot for comfort. Some surviving breastplates, probably Italian, do have a central rivet that both pivots and slides in a slot. Internal leather connections on either side keep the overlapping edges from overturning and obstructing movement [ref_arm_3718] PDF [ref_arm_3719] PDF [ref_arm_3724] PDF.

German breastplates with a single screw lack these straps and their rivet holes. A screw is unsuitable as a pivot because repeated movement would loosen it. A locknut could prevent this, but might injure the wearer under a blow. Without lateral leather connections, the plate edges could also overturn and lock against one another, dangerously restricting movement.

Moreover, many screw-connected breastplates have medial ridges on both plates [ref_arm_3751] PDF [ref_arm_3593] PDF. Once tightened, the nested ridges would prevent rotation. A simple rivet would have been the easier solution if articulation were the purpose. These considerations make it very likely that the detachable joint relates instead to the clothing combinations shown in contemporary images.

One possible dressing sequence begins with the chest plate held against the body and the jacket closed over it.151 The abdominal and pelvic plates are then placed outside and screwed to the concealed chest plate through a buttonhole or slit.152 A waist belt secures the assembly. With a close-fitting jacket, shoulder attachments might be unnecessary. Alternatively, the chest plate could be independently secured beneath the jacket by two shoulder straps crossed at the back and buckled in front, as discussed above. Either arrangement would make the abdominal and pelvic plates appear to be the only ones worn.

Other combinations may also have existed. The figure in [ref_ill_art_5293] PDF appears to wear a textile skirt over the pelvic lames. It could instead show a breastplate combining Types III and IV,153 with the chest and abdominal plates outside the garment and the pelvic lames beneath it.

Redaktionelle Hinweise · 1
  • Die rhetorische Annahme, ein Kämpfer könne keinen Grund für einen ungeschützten Brustbereich gehabt haben, wurde ausdrücklich als Argument des Originals kenntlich gemacht. Sie darf gemäß Terminologieleitlinien nicht als Beweis für eine verborgene Platte oder für Ganzkörperpanzerung behandelt werden. Die anschließende Rekonstruktion bleibt eine Hypothese.
Originalwortlaut vergleichen
4.2.5.2.2 Type-IV 



As said above, the abdomen -plate of type -IV breastplates may have developed by t he 



extension of the adjacent first pelvis -lame. Its central point might imitate a feature of a 



contemporary craftsman’s apron [ ref_ill_art_5300] [ ref_ill_art_5301] (descr. 2) 



[ref_ill_art_5302] [ ref_ill_art_5365]. Just like an apron, also t he abdomen - plates of 



breastplates were sometimes worn upon an undergarment, apparently without a thorax-plate. 



Single abdomen-plates worn upon a jacket [ ref_ill_art_5294] or upon a ring -armour shirt 



[ref_ill_art_5287] are illustrated in several contemporary artworks, mainly of Burgundian 



origin. Also in other European regions, breastplates seem to have been worn this way 



[ref_ill_art_5281]. At the depiction [ref_ill_art_5338], only the abdomen-plate without any 



pelvis protection is visible. Generally, a color-contrast between the upper and the lower plate 



was obviously in fashion in the 15 th century, as the thorax -plate could also be covered by 



leather or fabric [ref_ill_art_5164].  



The question is how these single abdomen -plates seen on the aforesaid depictions were 



fastened to the body. It is of course possible that the waist-belt was sufficient, but the upper 



point of the plate would presumably not hold very close to the c hest if it was not fastened. 



Furthermore, there is no obvious reason why a man at arms should have left his thorax 



exposed, while the rest of his body is sufficiently protected. 



Some features on extant armour plates might help to explain how these breastpl ates could 



have been fastened. The upper parts of many plates of type-IV – especially at those probably



made in the German speaking lands – are held together by only one single screw. There is 



usually a thread cut into the thorax -plate. It seems as if the holes for the thread had been 



punched from the exterior by means of a pointed tool. The plate material would probably be 



too thin to contain a sufficient number of coils [ ref_arm_3630]. The material displaced by 



the punching of the holes shapes a cone at the interior edge of the hole and thus more coils 



can be cut into the plate. The production of a screw and the fitting thread in the plate requires 



a lot of work and certain skills. This raises the question,  why the armourer’s did not simply 



rivet the pieces together.  



Many of these screwed plates show up to three vertical positioning holes on the inside 



[ref_arm_3679]. This feature might have had the purpose of adjusting the length of the plate 



to wearers of different heights. Another possibility is that the plates should pivot around the 



central screw for the comfort of the wearer. There are actually extant breastplates where a 



central rivet is sliding and pi voting in a slit. At these examples – probably of Italian 



production – to the left and to the right of this joint an interior leather -joint is permanently 



applied to prevent the edges of the thorax - and the abdomen -plate from flipping over and 



blocking the motion of the wearer [ ref_arm_3718] [ref_arm_3719] [ref_arm_3724]. At the 



German breastplates with only a single screw no such leather or the rivet holes can be found. 



A screw is not suitable for a pivoting joint. The permanent motion would result in a self -



loosening of the screw. To avoid this effect the screw would have to get fixed by a locknut. 



This would mean that the interior nut could injure the wearer when the breastplate received 



a blow. The second problem is that without the interior leather straps mentioned above the 



plates could flip over at the edges, making it impossible for the wearer to move pr operly, 



which in battle could easily create a dangerous situation. The fact that many breastplates 



with a central screw -joint have a medial ridge at both the thorax - and the abdomen -plate 



[ref_arm_3751] [ref_arm_3593] makes it unlikely that the system was intended to increase 



the flexibility. Once the screw would have been tightened, due to these two ridges spanned 



into each other the plates would not pivot a nymore. After all, if the intention was to make 



the plates pivoting a simple rivet would have been the easiest solution. 



For the aforesaid reasons, it is very likely that the detachable connection of the breastplates 



is linked to the wearing -variations of type-IV breastplates seen on many contemporary 



artworks. It is possible that the wearer had put the plates on in the following order: First he 



held the thorax-plate to his body and closed his jacket upon it. 151 Onto this jacket, he now 



placed the abdomen- and the pelvis-plates and screwed them to the thorax -plates through a 



button hole or a slit in the fabric.152 A belt at the waist would hold the plates tight to the body. 



Together with a close fitting jacket a fastening at the shoulders would probably not be 



necessary. It is also possible that the thorax -plate was separately fastened under the jacket 



by two straps, attached to the shoulders, crossed at the back and buckled at the front (see 



discussion and video above). If the breastplate was fastened in such a combination with the 



clothing, it would look as if only the abdomen- and the pelvis-plates were worn. 



There might have been more types of breastplates that could have been worn in different 



combination with the clothing. A very special combination is seen on the statue 



[ref_ill_art_5293]. The figure seems to wear a textile skirt upon the pelvis -lames of his 



breastplate. It is also possible that this breastplate is of another type – a combination between



-III and -IV153 – and the abdomen - and thorax -plates are worn upon, the pelvis -lames 



underneath the garment.
S. 114 · Sprachlich überarbeitet · Entwurf

4.2.5.3 Fastening other armour elements

Originalwortlaut vergleichen
4.2.5.3 The fastening of other armour parts
S. 114 · Sprachlich überarbeitet · Entwurf

4.2.5.3.1.1 Shoulders

Fifteenth-century shoulder defences were generally laced to the undergarment near their upper edges [ref_arm_282] PDF [ref_arm_334] PDF [ref_arm_611] PDF [ref_arm_733] PDF. A tapestry showing a wounded knight whose arm defences have been removed reveals the attachment laces on his jacket sleeves [ref_ill_art_5158] PDF. Around 1500, shoulders were sometimes buckled, probably to breastplate straps or neck protection [ref_arm_266] PDF.

The lower lames of Type II shoulders [ref_arm_755] PDF were usually buckled to the upper-arm defence, although permanent pivoting and sliding rivet connections also occur [ref_arm_605] PDF.154 Later fifteenth-century Type I shoulders were generally permanently connected to the upper-arm defence. Their upper lames used pivoting [ref_arm_310] PDF or sliding rivets [ref_arm_569] PDF. The lames between shoulder and upper arm were connected by leather at the front and centre, with sliding rivets only at the rear [ref_arm_304] PDF.

Originalwortlaut vergleichen
4.2.5.3.1.1 Shoulder 



Shoulder-defenses in the 15 th century were usually fastened to the undergarment via laces 



close to the upper edge [ ref_arm_282] [ref_arm_334] [ref_arm_611] [ref_arm_733]. The 



tapestry [ref_ill_art_5158] shows a wounded knight whose arm defenses had been taken off. 



The laces for their fastening are visible at the sleeves of his jac ket. Around the year 1500, 



sometimes the shoulders were buckled, probably to the straps of the breastplate or to a neck-



protection [ref_arm_266]. The lower lames of type-II [ref_arm_755] shoulders were usually 



buckled to the upper arm-defense, but they could also be connected permanently via pivoting 



and via sliding rivet-joints [ref_arm_605].154 Type-I shoulders of the second half of the 15th 



century were usually permanently connected to the upper arm -protection. The upper lames 



of the shoulders were connected via pivoting [ref_arm_310] or sliding [ref_arm_569] rivet-



joints. The lames between the shoulder and the upper arm had at the front side and in the 



center leather-joints and only at the rear sliding rivet-joints [ref_arm_304].
S. 114 · Sprachlich überarbeitet · Entwurf

4.2.5.3.1.2 Upper arms

In the fourteenth century, an upper-arm plate could be laced to the undergarment [ref_ill_art_5268] PDF (description 2); later it was buckled around the arm [ref_ill_art_5261] PDF [ref_arm_277] PDF. In the Italian system, the upper-arm defence was permanently joined to the elbow by pivoting rivets [ref_arm_1017] PDF. Leather riveted inside its upper edge provided an attachment through which it was laced to the garment [ref_arm_3933] PDF.

A painting showing paired arm and leg defences hanging on a wall clearly depicts the leather attachments at their upper ends [ref_ill_art_5372] PDF. Other images show sleeve laces for shoulder and upper-arm protection [ref_ill_art_5288] PDF [ref_ill_art_5308] PDF. German upper-arm defences were connected to the forearm by internal leather joints [ref_arm_249] PDF.

Originalwortlaut vergleichen
4.2.5.3.1.2 Upper arm 



In the 14th century, the plate could be laced [ref_ill_art_5268] (descr. 2) to the undergarment, 



later it was buckled to the arm [ ref_ill_art_5261] [ ref_arm_277]. Upper arms on arm -



defenses of the Italian system were permanently connected to the elbow via pivoting rivet -



joints [ ref_arm_1017]. At the upper end they had leather -straps riveted to the interior. 



Through this leather the upper arm was laced to the undergarment [ ref_arm_3933]. In the 



center of the painting [ref_ill_art_5372], pairs of arm and leg-protections are hanging at the 



wall. At their upper ends the interiorly attached leather straps are clearly visible. Some 



contemporary artworks show the laces at the sleeves of undergarments for the fastening of 



the shoulders and the upper arm -protections [ ref_ill_art_5288] [ ref_ill_art_5308]. The 



German upper arm defenses were connected to the lower arm via interior leather -joints 



[ref_arm_249].
S. 114 · Sprachlich überarbeitet · Entwurf

4.2.5.3.1.3 Elbows

Italian-system elbow defences were strapped around the arm and permanently connected to the upper arm and forearm by articulated rivet joints [ref_arm_143] PDF. The lowest lame between elbow and forearm permitted rotation through sliding rivets [ref_arm_809] PDF. By the late fifteenth century, Spanish and Flemish examples generally joined this lame to the forearm with simple pivoting rivets [ref_arm_1012] PDF.

In German systems, the elbow was buckled around the arm and riveted [ref_arm_263] PDF or laced [ref_ill_art_5260] PDF to the leather connection between upper-arm and forearm defences.155

Originalwortlaut vergleichen
4.2.5.3.1.3 Elbow 



Elbows of the Italian system were fastened by a strap a nd a buckle to the arm and also 



permanently connected to the upper and the lower arm via pivoting rivet -joints 



[ref_arm_143]. The lowest lame in between the elbow and the lower arm was turning via 



sliding rivets [ref_arm_809]. By the end of the 15th century, in Spain and Flanders the lowest 



lame was usually connected to the lower arm via simple pivoting rivet -joints 



[ref_arm_1012]. Elbows in German arm -defense systems were buckled to the arm and 



riveted [ref_arm_263] or laced [ref_ill_art_5260]155 to the leather-joint in between the upper 



and the lower arm.
S. 114–115 · Sprachlich überarbeitet · Entwurf

4.2.5.3.1.4 Forearms

Only Type I forearm plates required a strap and buckle to hold the open defence against the arm [ref_arm_4926] PDF. The enclosing plates of Type III instead needed a closure: straps and buckles occur on [ref_arm_723] PDF [ref_arm_248] PDF, while German, Flemish and Spanish examples sometimes use a spring catch [ref_arm_365] PDF. Their opening plates were hinged. German forearm defences connected to the upper arm through internal leather, whereas Italian examples used a rotating sliding-rivet connection.

Originalwortlaut vergleichen
4.2.5.3.1.4 Lower arm 



Only lower arms of type -I needed to be fastened by a strap and a buckle [ ref_arm_4926]. 



The encircling plates of type-III examples were closed by a strap and a buckle [ref_arm_723] 



[ref_arm_248] and the German, Flemish or Spanish models were sometime s closed by a



spring-catch [ref_arm_365]. In both regions, the flaps were articulating via hinges. To the 



upper arm the German lower arm-defenses were connected via an interior leather-joint while 



the Italian examples were turning via a sliding rivet-joint.
S. 115 · Sprachlich überarbeitet · Entwurf

4.2.5.3.2.1 Thighs

Thigh defences usually had a leather or linen strip riveted inside the upper edge [ref_arm_2839] PDF [ref_ill_art_5231] PDF (description 1). This was probably laced upwards to a strong waist belt, although no depictions support the suggestion. The knee lames generally used pivoting rivets on the inner, big-toe side and sliding rivets on the outer, little-toe side [ref_arm_2366] PDF. The side plates of Type II thigh defences were hinged.

Originalwortlaut vergleichen
4.2.5.3.2.1 Upper leg 



At the upper edge, these defenses usually had a leather- or linen-strap riveted to the interior 



[ref_arm_2839] [ref_ill_art_5231] (descr. 1). This was probably laced upwards to a strong 



waist-belt. There are no depictions that could support this assumption. The knee-lames were 



usually connected at the big-toe side via pivoting rivets and at the small toe-side via sliding 



rivet-joints [ref_arm_2366]. The flaps of type-II upper legs were articulated by hinges.
S. 115 · Sprachlich überarbeitet · Entwurf

4.2.5.3.2.2 Knees

Type II knee defences connected to their upper and lower lames through sliding rivets on the outer side and pivoting rivets on the inner side. A strap and buckle held the main plate against the knee. The lower-leg defence was always attached by a removable connection, such as a rotating locking bolt combined with a strap and buckle [ref_arm_2413] PDF [ref_arm_2840] PDF.

Originalwortlaut vergleichen
4.2.5.3.2.2 Knee 



Knee protections of type -II at the small toe side had sliding rivet-joints and at the big -toe-



side pivoting rivet-joints for the connection to the upper and the lower lames. The main plate 



was fastened to the knee by a strap and a buckle. The lower legs were always connected via 



a detachable joint like a turning lock ing bolt together with a strap and a buckle 



[ref_arm_2413] [ref_arm_2840].
S. 115 · Sprachlich überarbeitet · Entwurf

4.2.5.3.2.3 Lower legs and feet

Italian Type III lower-leg defences were closed around the leg with straps and buckles [ref_arm_2308] PDF; German counterparts used spring catches [ref_arm_2306] PDF. Their opening plates were always hinged.

Foot fastenings are harder to reconstruct because few original arrangements survive. Some Type II foot defences were connected by spring locks [ref_arm_2240] PDF. Type III examples had an articulated heel plate closed by a spring catch at the ankle [ref_arm_2248] PDF. In Italian armour, ring-armour foot protection was attached directly to the lower-leg defence, as reconstructed on [ref_arm_2295] PDF. Foot protection could also be laced to a shoe [ref_ill_art_5283] PDF [ref_arm_2956] PDF.

Redaktionelle Hinweise · 1
  • „Knuckle“ wurde im Kontext der Fersenklappe als Knöchel/„ankle“ wiedergegeben, entsprechend der bereits markierten Lesart im Typologiekapitel. Anatomische Zuordnung bei der Autorendurchsicht bestätigen.
Originalwortlaut vergleichen
4.2.5.3.2.3 Lower Leg and foot 



Italian lower leg defenses of type -III were fastened to the l eg by straps and buckles 



[ref_arm_2308], their German pendants were closed by a spring-catch [ref_arm_2306]. The 



flaps were always articulated via hinges. T he fastening of the foot -protection cannot 



sufficiently be reconstructed, as only few genuine systems are extant. In some cases, foot 



protections of type-II were connected by spring-locks [ref_arm_2240]. Type-III defenses had 



an articulated flap at the heel which was closed at the knuckle via a spring catch 



[ref_arm_2248]. At Italian armour, the defense was consisting of ring -armour which was 



directly connect ed to the lower leg -defense (reconstructed at [ ref_arm_2295]). The foot -



defenses could also be fastened to the shoe by laces [ref_ill_art_5283] [ref_arm_2956].
S. 115 · Sprachlich überarbeitet · Entwurf

4.2.5.3.3 Neck

Type I and II neck defences [ref_arm_3062] PDF [ref_arm_3044] PDF were generally secured around the neck with a strap and buckle. Whether, and how, the lower plate attached to the breastplate is more difficult to establish. Expensive examples could use an elaborate spring lock [ref_arm_3066] PDF [ref_arm_3064] PDF, which made a neck strap unnecessary.

Several neck defences have two holes near the lower edge [ref_arm_3042] PDF, but breastplates generally lack holes in corresponding positions. Where approximate matches occur, they may once have held a locking mechanism [ref_arm_3061] PDF. Some examples were probably screwed to the breastplate [ref_arm_3034] PDF. Buckled attachment is documented only in images [ref_ill_art_5196] PDF [ref_ill_art_5213] PDF [ref_ill_art_5219] PDF (description 3).

The upper lames always used pivoting rivets and were prevented from dropping by a spring catch on the right [ref_arm_3099] PDF. Lower plates were either rigidly riveted to the chin plate [ref_arm_3090] PDF or joined by pivoting rivets [ref_arm_3065] PDF.

Originalwortlaut vergleichen
4.2.5.3.3 Neck 



A neck-protection of type-I or -II [ref_arm_3062] [ref_arm_3044] is usually attached to the 



wearer’s neck via a strap and a buckle. It is rather difficult to reconstruct if or how the lower 



plate was connected to the breastplate. Neck -defenses at costly armour can be attached to 



the breastplate via a sophisticated spring lock -mechanism [ref_arm_3066] [ref_arm_3064]. 



This joint-type made a strap at the neck unnecessary. Several examples show two holes close 



to the lower edge [ ref_arm_3042], but usually breastplates do not have holes at the 



corresponding locations. Where more or less corresponding holes can be found, it is possible 



that these holes once fixed a lock -mechanism [ ref_arm_3061]. In a few cases, the neck -



protection was probably screwed to the breastplate [ ref_arm_3034]. The fastening of the 



neck-protection to the breastplate via a buckle is only evident in artworks [ref_ill_art_5196] 



[ref_ill_art_5213] [ ref_ill_art_5219] (descr. 3). The upper lames were always joined by 



pivoting rivets. They were prevented from pivoting downwards by a spring-catch at the right 



side [ ref_arm_3099]. Lower plates were permanently riveted to the chin -plate 



[ref_arm_3090] or via pivoting rivet-joints [ref_arm_3065].
S. 115–116 · Sprachlich überarbeitet · Entwurf

4.2.5.3.4 Head

A helmet’s padded lining helps hold it in place. Additional fastening beneath the chin or to the breastplate is nevertheless necessary to prevent blows from dislodging it. Early chin fastenings are difficult to reconstruct. Type I, II, III and IV helmets, and early Type V examples, lack dedicated internal chin-strap rivet holes. Their straps must therefore have shared structural rivets, such as those securing the lining leather [ref_arm_1345] PDF, or been attached directly to the lining.

Type VI helmets were most probably retained solely by cheek plates that also enclosed the chin. Type VIII helmets were usually fixed to the breastplate [ref_ill_art_5173] PDF and sometimes also to the backplate [ref_arm_1650] PDF. By the mid-fifteenth century, nearly all Type III, V and VII helmets had two rivets or holes on each side below the lining attachments [ref_arm_1381] PDF. These certainly secured chin straps, generally cut to a Y shape [ref_ill_art_5346] PDF. A few helmets retain straps or fragments from their period of use [ref_arm_1421] PDF [ref_arm_1704] PDF [ref_arm_1759] PDF [ref_arm_1849] PDF [ref_arm_2033] PDF [ref_arm_1860] PDF [ref_arm_1861] PDF.

Several Type III [ref_arm_1348] PDF, Type V [ref_arm_1787] PDF [ref_arm_2026] PDF and Type VII helmets [ref_arm_1743] PDF [ref_arm_1755] PDF have two apparently functionless holes at the nape. They may have held an internal leather loop [ref_arm_1847] PDF or staple [ref_arm_1711] PDF [ref_arm_1713] PDF [ref_arm_1732] PDF for hanging the helmet on a wall or from a belt while marching.

For Type III, contemporary paintings suggest another possibility: helmets could be secured to a buckle on the wearer’s back protection [ref_ill_art_5189] PDF [ref_ill_art_5147] PDF. Corresponding buckles occur at the upper ends of early segmented back defences [ref_arm_4789] PDF [ref_arm_4767] PDF [ref_arm_4792] PDF.

Originalwortlaut vergleichen
4.2.5.3.4 Head 



The interior lining of a hea d defense plays an important role in the fastening of the helmet 



to the head. A padded lining already helped to keep the helmet in place. Nevertheless, it is 



necessary to fasten the helmet also to the chin or to the breastplate to prevent it from slipping 



off the head when blows stroke the helmet. Despite this assumption, the chin fastening of



early helmets cannot easily be reconstructed. Type-I, -II, – III, -IV , and early type-V helmets 



never show riveting holes for the interior attachment of a chin -strap. The only possibility is 



that the chin-straps were either fastened at other constructive rivets like those that held the 



lining-leather [ref_arm_1345] or they were directly attached to the lining. Type-VI helmets 



were most likely fastened only via the cheek -plates that also surrounded the chin. Helmets 



of type-VIII were usually fixed to the breastplate [ ref_ill_art_5173] and in some cases also 



to the backplate [ref_arm_1650]. By the mid-15th century, nearly all helmets of type-III, -V 



and -VII showed two rivets or rivet -holes at each side below the lining rivets 



[ref_arm_1381]. Here certainly the chin -straps were attached, usually cut in a Y -shape 



[ref_ill_art_5346]. A few helmets still retain straps or their fragments from the time of use 



[ref_arm_1421] [ ref_arm_1704] [ ref_arm_1759] [ ref_arm_1849] [ ref_arm_2033] 



[ref_arm_1860] [ref_arm_1861].  



At several helmets of type-III [ref_arm_1348] -V [ref_arm_1787] [ref_arm_2026] and -VII 



[ref_arm_1743] [ref_arm_1755] at the nape-protection a pair of functionless holes is visible. 



It is possible that these holes usually held an interior leather-strap [ref_arm_1847] or a staple 



[ref_arm_1711] [ref_arm_1713] [ref_arm_1732] for the hanging of the helmet to the wall or 



two the belt when on march. At least for type -III helmets another possible explanation is 



seen on contemporary illustrations. On the paintings [ ref_ill_art_5189] and 



[ref_ill_art_5147], men -at-arms are wearing helmets of type -III that could be fixed to a 



buckle at the man’s back -protection. The early segmented backpl ates [ ref_arm_4789] 



[ref_arm_4767] [ref_arm_4792] have corresponding buckles attached at their upper end.
S. 116 · Sprachlich überarbeitet · Entwurf

4.2.5.3.5 Hands

Hand-protection plates were generally held in place partly by a permanently attached inner glove. The earliest Type I examples have no additional strap and buckle. Some simple Type I defences from the first half of the fifteenth century were worn without an inner glove [ref_ill_art_5211] PDF (description 2), making straps necessary.

The articulated cuffs of later fifteenth-century Type III and IV hand protection required a second strap. A monumental brass shows an alternative: a single Y-shaped leather strap secures both wrist and cuff, apparently sharing a rivet with the articulated joint [ref_ill_art_5353] PDF. The straps on [ref_arm_1044] PDF are similarly attached.

Type III and IV hand protection rarely had a hinged cuff plate that fully enclosed the wrist. One example, [ref_arm_1060] PDF, closes with a spring catch. Several others have only a short hinged plate, secured by a strap and buckle and usually hinged on the thumb side156 [ref_arm_1075] PDF [ref_arm_1081] PDF [ref_arm_1245] PDF. On other examples, paired holes in the corresponding position suggest a lost hinge [ref_arm_1078] PDF [ref_arm_1080] PDF [ref_arm_1128] PDF [ref_arm_1228] PDF [ref_arm_4904] PDF.

A unique Type I variant, [ref_arm_1264] PDF, does not enclose the wrist with one continuous plate. Instead, a separate articulated plate closes the palm side.

Originalwortlaut vergleichen
4.2.5.3.5 Hand 



The plates for the protection of the hand were usually for one part fastened to the hand via a 



permanently attached lining-glove. The oldest type-I examples do not show any additional 



fastening via a strap and a buckle. A few simple type -I hand-protections of the first half of 



the 15 th century were worn without a lining [ ref_ill_art_5211] (descr. 2)  and therefore 



fastening-straps became necessary. As the cuffs of type -III and -IV hand-protections in the 



second half of the century were articulated, a second strap became necessary for the fastening 



of the cuff. A brass effigy shows in details how a single Y -shaped leather strap could 



alternatively fasten both, the wrist and the cuff at the same time. The strap seems to use the 



same rivet as the articulated joint [ref_ill_art_5353]. At the hand-protections [ref_arm_1044] 



the strap is attached similarly. Type-III and -IV hand-protections only rarely had an entirely 



enclosing flap at the cuff. One example is [ ref_arm_1060], where the flap is locked via a 



spring-catch. Several examples have a short flap only that is fastened via a strap and a buckle 



and articulated by one hinge, frequently attached to the thumb -side156 [ref_arm_1075] 



[ref_arm_1081] [ ref_arm_1245]. On some examples the two holes at the corresponding 



location of the cuff suggest that a flap -hinge had once been attached [ ref_arm_1078] 



[ref_arm_1080] [ref_arm_1128] [ref_arm_1228] [ref_arm_4904]. There is one very special 



version of type-I hand-protection. This is the only example where the plate is not completely 



enclosing the wrist, but instead an articulated flap is attached at the pulse -side 



[ref_arm_1264].
S. 117 · Sprachlich überarbeitet · Entwurf

4.2.6.1 Linings

Rigid iron plate is uncomfortable against the body. Armourers therefore had to make it safer and more comfortable to wear. Where necessary, field armour of the period examined was fitted with an internal lining.157 All helmets and neck defences—except neck protection attached to Type VI helmets—required padding. The leather gloves inside hand protection were probably unpadded. Padded limb linings intended for comfort are not known from this period, and torso protection was generally unpadded.

Traces left by lost linings, principally empty holes, together with the functional need for padding, provide the basis for reconstructing their attachment. Where expected attachment holes are absent or make no functional sense, it is worth asking whether the object could have worked as intended and whether it might be a reproduction. Surviving examples are discussed below.

Redaktionelle Hinweise · 1
  • Die Einleitung formuliert die Notwendigkeit von Polsterungen pauschal; §4.2.6.1.3 unterscheidet anschließend separate Polsterhauben und über anderen Helmen getragene Helme. Diese Abstufung bleibt erhalten.
Originalwortlaut vergleichen
4.2.6.1 Lining 



The iron plate itself is inflexible and hard, an uncomfortable thing to be worn directly on the 



body. The armourers had to find solutions on how to make the wear more convenient and 



safer. Therefore, certain field armour parts of the considered period where necessary were 



equipped with an interior lining 157. Without exception, all neck -protections – with the 



exception of those attached to helmets of type -VI – and of course all helmets were only 



usable with a padded lining. Leather gloves inside hand armour were most likely not padded. 



In the considered period, linings at protections for the limbs for the convenience of the 



wearer are not known and also torso-protections are usually not padded.  



The traces that lost linings left at the objects – mainly empty holes – and the knowledge that 



the item once must have been padded are the basis for the reconstruction of the former 



attachment. If no traces of a lining – i. e. no holes – are visible, or where visible holes make 



no sense, the question might be asked if the object could function at all and could thus be a 



reproduction. In the following the different extant examples of linings are discussed.
S. 117 · Sprachlich überarbeitet · Entwurf

4.2.6.1.1 Arms and legs

The only limb attachments resembling linings are leather strips riveted inside the edges. They occur where unturned metal might wear through the underlying clothing, for example on the side plates of the thigh defence [ref_arm_2839] PDF, where fragments survive.158 The leather at the upper edge of its main plate, used to lace the defence to the undergarment, also appears to have an inner layer of linen. This probably protected the clothing from the attachment rivets and limited stretching of the leather under load.

Leather strips often lined the inner upper edges of the lowest knee lames [ref_arm_2367] PDF [ref_arm_2371] PDF. Such strips could also protect underlying armour from constant contact with another plate edge. The practice seems to have become widespread in the sixteenth century. On [ref_arm_5105] PDF, red velvet borders the shoulders and the thigh protection attached to the torso, probably as a late sixteenth-century addition.159

I know of no elbow or knee defence with an internal leather strip around its shell-like extension. No further examples of this edge protection appear before the very end of the fifteenth century, when the shoulder defences [ref_arm_528] PDF seem to have leather inside their wings where they would rub against breastplate and backplate. The early shoulder defence [ref_arm_881] PDF retains a textile lining covering its entire inner surface, with horizontal green and white stripes but no padding.

Limb protection must fit closely to allow free movement. This probably explains the absence of padding: a thin, strong undergarment was presumably considered sufficient. The slender, close-fitting design of all surviving pre-1500 limb defences supports this interpretation.

Originalwortlaut vergleichen
4.2.6.1.1 Arms and legs 



The only application that could be considered as some sort of lining for limb protections are 



leather straps riveted interiorly along the edges. They appear where the unturned plate edges 



would wear off the fighter’s garments worn underneath, e. g. at the flaps of the upper legs 



[ref_arm_2839], where some fragments survive158. Here it also seems like the leather at the 



upper end of the main plate, through which the leg armour was laced to the undergarment, 



was also interiorly lined with linen -fabric. This should probably prevent the garment from 



wear by the rivets that hold the leather. The fabric also prevents the leather from getting 



stretched by the wearing-stresses. Also the interior upper edge of the lowest knee-lame was 



often equipped with a leather st rap [ ref_arm_2367] [ ref_arm_2371]. Where plate -edges 



would permanently scratch the surface of other subjacent armour parts, such straps are 



attached. It seems like this technique was widely adopted in the 16 th century. At the armour 



[ref_arm_5105] the shoulders and the torso-upper leg-protections have their edges lined with 



red velvet, probably attached in the  late 16th century159. No elbow or knee defense with an 



interior leather strap at the edges of the shell like extension is known to the author. No other 



example seems to exist until by the very end of the 15th century the shoulders [ref_arm_528] 



seem to have leather straps at the inner sides of the wings, where they would scratch the 



breast- and the backplate. The early shoulder [ref_arm_881] still retains its lining being made 



of fabric and covering the entire interior surface. It is horizontally colored by green and white 



stripes and has no padding. 



Limb-protections need to fit closely to the body so the wearer is free in his movements. 



This is probably the reason why such armour was never padded. It was probably considered 



sufficient to wear a thin but strong undergarment. These assumptions are supported by the 



fact that all extant limb protections before 1500 are very close fitting and lean in their design.
S. 118 · Sprachlich überarbeitet · Entwurf

4.2.6.1.2 Torso

Late medieval breastplates and backplates were never padded. A broad internal leather lining survives on one early breastplate [ref_arm_3811] PDF, where it also holds the segments together. Another breastplate, [ref_arm_3428] PDF, may once have had a lining. Small holes occur along the edges of each recessed area of its decoration. They may have secured external metal bands, comparable to [ref_arm_3621] PDF, or drawn an outer textile or leather covering into the recesses so that it followed the embossed pattern.

A surviving rivet beneath the left arm opening supports the possibility of an internal lining: it retains a small inner washer,160 which would make sense only as an attachment for organic material. Since the breastplate was altered and reused, the question may never be resolved. It may have been riveted to an undergarment, perhaps itself reinforced inside, as in [ref_ill_art_5263] PDF.

Some late fifteenth-century [ref_arm_3426] PDF161 and early sixteenth-century breastplates [ref_arm_3473] PDF have small holes around their edges. Their purpose is uncertain: they may have secured an internal lining or an external covering. From about 1600, bullet-resistant “Kürassier” breastplates and backplates often had padded internal linings.

Thigh protection attached to the torso appears to have lacked internal leather edging before about 1480. The earliest examples may be [ref_arm_3782] PDF [ref_arm_3837] PDF, where edge holes or rivets suggest former leather strips. Small rivet heads along the lower edges of [ref_arm_3574] PDF [ref_arm_5106] PDF probably still secure internal leather. Because these plain iron heads differ from the capped rivets elsewhere on the suit, the strips may be later additions.

Originalwortlaut vergleichen
4.2.6.1.2 Torso 



Breast- and backplates in the late Middle Ages never were padded. Only at one early 



breastplate [ ref_arm_3811] an interior large leather lining survives. It also holds the 



segments of this breastplate together. The breastplate [ref_arm_3428] might once have been 



equipped with a lining. Along the edges of each “valley” of the embossing a small hole can 



be seen. It is possible that they once he ld outer metal -bands in place (compare 



[ref_arm_3621]) or they even spanned an exterior cover into the “valleys”, so the fabric or 



leather would follow the pattern of the embossing. One detail that supports  the former 



attachment of an interior lining is a rivet remaining in one of the said holes under the left 



arm-cutout. Interiorly it still retains a small washer 160, which would only make sense if it 



held some organic part in place. As this breastplate has be en altered and re -used in later 



times, these questions might never be answered sufficiently. One possible constellation is 



that the breastplate had been riveted to an undergarment, maybe itself reinforced interiorly 



like [ref_ill_art_5263]. There are breastplates of the late 15th [ref_arm_3426]161 or early 16th 



[ref_arm_3473] century with small  holes along the edges. The purpose of these holes is 



uncertain. They could have served for the application of an interior lining or an exterior 



cover. Bullet -proof „Kürassier” breast - and backplates from 1600 on do often have an 



interior, usually padded lining.  



Torso-upper leg -protections seem to have had no interior leather straps along the edges 



before 1480 ca. The earliest examples might be [ ref_arm_3782] and [ ref_arm_3837]. The 



holes or rivets along the edges lead to the assumption that the torso -upper leg-protections 



once held leather at the interior. At the lower edge of the examples [ ref_arm_3574] and 



[ref_arm_5106] small rivet heads are visible, which probably still hold a leather strap 



interiorly. As the small iron rivet heads differ from the otherwise capped he ads found 



elsewhere at the suit, it is possible that the leather bands had been attached secondarily.
S. 118–121 · Sprachlich überarbeitet · Entwurf

4.2.6.1.3 Helmets

The head is particularly exposed and vulnerable in combat. Even when a helmet resists penetration, an impact transmitted directly from metal to skull can cause injury. Padding reduces that force and helps retain the helmet during fighting, running or riding. Stability matters because a displaced helmet can obstruct vision.

It is very unlikely that a combat helmet was worn without some form of lining or padding. This need not have been attached to the metal: a separate padded cap could serve the purpose. Type I helmets, probably used since the High Middle Ages [ref_ill_art_5180] PDF and generally difficult to date, may still have been worn over such caps after 1350.162

From 1350 onwards, helmets generally had fixed padded linings. Large Type II helmets worn over Type IV or V helmets were probably an exception. They did not necessarily require their own padding, although a lining could help hold the outer helmet in the correct position for vision. Fourteenth-century sculptures show linings inside Type II helmets [ref_ill_art_5278] PDF [ref_ill_art_5398] PDF. Contemporary paintings also depict the interiors of Type VII [ref_ill_art_5178] PDF and Type V helmets [ref_ill_art_5192] PDF.

The Churburg Armoury is particularly important for studying linings. Of approximately twenty-nine surviving examples or fragments, including [ref_arm_1420] PDF [ref_arm_1799] PDF [ref_arm_2067] PDF [ref_arm_2113] PDF, eleven remain at Churburg and another three formerly belonged there.163 The linings in [ref_arm_1803] PDF [ref_arm_1804] PDF are replacements fitted within roughly the century before this study.

Linings most likely to preserve the original or earliest arrangement have either a row of triangular panels whose tips are drawn together with a cord to form a dome [ref_arm_1732] PDF [ref_arm_1787] PDF [ref_arm_1797] PDF [ref_arm_1849] PDF [ref_arm_1858] PDF [ref_arm_1859] PDF [ref_arm_1860] PDF [ref_arm_1861] PDF, or a closed padded cap [ref_arm_1745] PDF [ref_arm_1812] PDF [ref_arm_1978] PDF [ref_arm_2033] PDF [ref_arm_2180] PDF. The sole surviving Type VI lining, in [ref_arm_1932] PDF, is carefully tailored to the complex interior while permitting the cheek plates to open.

The few original linings generally use plant-fibre fabric. Expensive armour might receive a more comfortable material, either originally or as a replacement. The Type III helmet [ref_arm_1418] PDF has green velvet, while [ref_arm_1495] PDF has wool.164 Lining materials are fragile and have often disintegrated completely. Comparing empty holes and apparently redundant rivets with surviving attachments nevertheless helps reconstruct the lost organic components.

Five attachment methods can be distinguished. The first uses a few pairs of relatively large holes at different points on the skull, generally on Type II [ref_arm_1463] PDF, Type VII [ref_arm_1732] PDF [ref_arm_1797] PDF165 and Type VIII helmets [ref_arm_1645] PDF. Laces from a separate padded cap pass through these holes and are tied outside. Different caps could accommodate different head sizes, for example when tournament armour changed users. Several such tournament-helmet linings survive in the HJRK, and I examined two in a private collection [ref_arm_1637] PDF [ref_arm_1638] PDF.

Pre-1500 Type II helmets are rare and generally poorly preserved, often as archaeological finds, making their lining arrangements difficult to reconstruct. Paired holes high on the skull may instead have secured a crest and mantling.166 Only one Type IV helmet, [ref_arm_1515] PDF, has skull holes that may have served a removable lining.167

The second method permanently sews the lining through closely spaced small holes around the lower edge and face opening. This occurs on early examples of Types I, IV, V, VI and VIII. At least three directly stitched linings survive. That in [ref_arm_1529] PDF may be original or a replacement and is the only surviving leather example. Copper-alloy eyelets reinforce its adjustment holes—a notable feature, although reinforcing stressed holes in this way was not unusual in the Middle Ages. The other two examples are at Churburg [ref_arm_1495] PDF [ref_arm_1559] PDF. The latter uses coarse linen padded with horse or cattle hair.168

The third method sews the lining to an internal leather band. From the late fourteenth century, helmets of all types generally have a row of more widely spaced, larger holes around the narrowest circumference of the skull, just above the ears. Surviving rivets often still secure, or once secured, a leather band to which the lining was sewn [ref_arm_1797] PDF.

The fourth method uses an iron strip riveted across the forehead inside the helmet, bridging the temples. It occurs on Type III [ref_arm_1404] PDF [ref_arm_1408] PDF and Type VII helmets [ref_arm_1743] PDF [ref_arm_1797] PDF. The lining was either riveted directly to the strip or sewn to leather attached to it. The purpose is unclear and appears not to have attracted scholarly attention. Perhaps the arrangement allowed this portion of the lining to be removed without opening all the usual front rivets. On Type VII helmets with lifting face guards, it also avoided external rivet heads that might obstruct the visor. Its occurrence on fixed-visored helmets and Type III examples suggests that another explanation may exist.

Linings attached by these methods could generally be repaired or replaced fairly easily. Opening rivets was expensive and time-consuming because they could not be reused. The lining leather was pierced along its lower edge before installation. A curved needle or pig’s bristle made it possible to sew fabric to the leather or metal support without specialist armour-making skills.

The fifth method rivets the textile itself directly to the plate above the ears [ref_arm_2113] PDF. Replacing such a lining requires all its attachment rivets to be opened. On [ref_arm_1710] PDF, this is most probably a later arrangement. Pivot holes and corrosion marks tracing the former forehead reinforcement show that the helmet once had a visor. The Type a rivets now holding its lining probably do not date from manufacture: two Type b rivets survive on the right, with internal washers, and probably once held a chin strap. The rivets concealed beneath the closed visor were very likely Type a, while those exposed were Type b and held an internal lining band. At some later date, the present coarse, unpadded lining was fitted.

The velvet lining in [ref_arm_1418] PDF probably also postdates manufacture. It is riveted directly to the brim, whereas a separate circumferential row above the ears probably held the original lining.

Redaktionelle Hinweise · 2
  • Zählungen und Zeitangaben beziehen sich auf den Erhebungsstand der Dissertation. Keine Aktualisierung des Bestands von Helmfuttern vorgenommen.
  • Die im Original angenommene leichte Auswechselbarkeit der ersten vier Befestigungsarten ist bei direkt vernieteten Varianten eingeschränkt; die folgenden Ausführungen zur Erneuerung bleiben erhalten.
Originalwortlaut vergleichen
4.2.6.1.3 Helmets 



The head is one of the most exposed and thus most vulnerable parts of the fighter’s body. 



Therefore, it needs special protection against blows of any kind. While the shell of a helmet 



should resist penetration in each situation, still the wearer’s head could get injured by the 



shock transferred directly from the plate to the skull. A padded lining can reduce the force 



of such an impact. It also helps to keep the helmet in place in situations of fierce fighting or 



other fast movements like running or riding. This is especially important as a sliding of the 



helmet could block the wearer’s sight. It is very unlikely that any war helmet had ever been 



worn without some kind of lining or padding. This does not necessarily have to be fixed to



the plate itself, but can also be designed as a separate padded cap. Helmets of type -I – 



probably used since the high Middle Ages [ ref_ill_art_5180] and usually very difficult to 



date – after 1350 might still be worn with such a cap underneath.162 



From 1350 on helmets were usually equipped with a fixed padded lining. Exceptions were 



probably helmets of type-II, which were large enough to be worn upon a helmet of type -IV 



or -V . These helmets did not necessarily need a lining, even though they might have had one 



to fix the outer helmet in a position that ensured a free sight. On a few 14th century sculptures, 



linings inside helmets of type -II are visible [ ref_ill_art_5278] [ ref_ill_art_5398]. 



Contemporary paintings show the in terior of helmets of type -VII [ref_ill_art_5178] and of 



type-V [ref_ill_art_5192]. 



For the study of the former appearance and functionality of linings, items from the Armoury 



of the castle of Churburg are of great significance. From a total of about 29 linings or their 



fragments [ref_arm_1420] [ref_arm_1799] [ref_arm_2067] [ref_arm_2113] already 11 are 



in the Churburg collections, while 3 further exam ples (=14) were sold from there and are 



now in other collections. 163 The linings inside the helmets [ ref_arm_1803] [ref_arm_1804] 



are replacements, attached i n the last hundred years ca. Extant linings that most likely 



resemble the original or oldest arrangement are made of a row of several triangular gussets, 



fastened at the points with a cord to form a dome [ ref_arm_1732] [ ref_arm_1787] 



[ref_arm_1797] [ ref_arm_1849] [ ref_arm_1858] [ ref_arm_1859] [ ref_arm_1860] 



[ref_arm_1861] or they form a closed padded cap [ ref_arm_1745] [ ref_arm_1812] 



[ref_arm_1978] [ref_arm_2033] [ref_arm_2180]. At the type-VI helmet [ref_arm_1932] the 



lining is elaborately tailored to cover the complex -shaped interior while allowing for the 



cheek-pieces to get opened. This is the only lining of a type-VI helmet to survive. According 



to the few helmets still retaining an original lining, it usually has been made of plant -fiber 



fabric. For costly armour this (or the later replacement) could also be made o f more 



comfortable material. At one type -III helmet a lining of green velvet is attached 



[ref_arm_1418]. In the case of [ref_arm_1495] it is made of wool. 164 The lining material is 



usually very fragile, at most extant armour pieces it had fallen to dust. Nevertheless, the 



comparison of empty holes or “useless” rivets with the lining -attachment of surviving 



examples sheds some light on the fastening of the lost organic parts.  



Five different attachment-types of interior linings can be observed. The first is remarked by 



few pairs of larger holes at different locations on the skull, usually only found on helmets of 



type-II [ref_arm_1463], -VII [ref_arm_1732] [ref_arm_1797]165 and -VIII [ref_arm_1645]. 



Through these holes the lacing of a separate padded cap was passed and tied at the outside. 



By using different linings, such helmets could thus become adjusted to another head-size, e. 



g. for changing users of tournament armour. In the HJRK in Vienna several of such linings 



for tournament helmets are preserved. The author has examined two examples in a private 



collection [ref_arm_1637] [ref_arm_1638]. The helmets of type-II from before 1500 are so



rare and also usually in bad condition – most of them are archaeological finds – that it is 



difficult to reconstruct the former attachment of the lining. The pairs of holes found at the 



upper skull of such helmets did not necessarily se rve the purpose of holding a lining. They 



could just as well have served for lacing the crest and the mantling 166. There is only one 



example of type-IV [ref_arm_1515] that shows holes in the skull which might167 have served 



for a detachable fixing of a lining.  



A second type of lining was attached permanently. Many helmets from the earlier years of 



the considered époque – of type-I, -IV , -V , -VI and -VIII – have small narrow holes all around 



the lower edge and the face opening. These served for attaching the lining by a seam of linen 



thread. At least three examples with a lining stitched directly to holes in the plate do survive. 



At the helmet [ref_arm_1529] it is not clear whether the lining is genuine or a replacement. 



It is the only lining to survive that is made of leather. The copper alloy thread -eyes at the 



points where this lining could be adjusted in size are remarkable, but in the Middle Ages it 



was not uncommon to strengthen stressed holes this way. The two other examples of extant 



linings are in the Churburg Armoury [ref_arm_1495] [ref_arm_1559]. The lining of the latter 



is made of rough linen, padded with horse or cow hair168. 



The third type of lining is usually sewn to an interior leather strap. From the late 14th century 



on, helmets of all types do usually have a line of larger holes – wider apart from each other 



– circumferential around the narrowest circumference of the skull, right above the line of the 



ears. Often the holes still retain rivets which once held the interior lining. In most cases an 



encircling interior leather strap was or still is fixed. T he lining itself was sewn to this band 



[ref_arm_1797].  



The fourth is a special type of attachment, remarked by an iron plate strap riveted interiorly 



to the forehead. This forms a kind of bridge from the left to the right temple. Such straps are 



found on helmets of type -III [ ref_arm_1404] [ ref_arm_1408] as well as on type -VII 



[ref_arm_1743] [ref_arm_1797]. The lining was either riveted directly to this plate or it was 



stitched to a leather band riveted to it. It is not clear what the purpose of this construction  



was. No study of helmets seems to have noticed it at all. For some reason, this part of the 



lining was probably supposed to be taken off with ease – without opening all the common 



frontal rivets. By fixing the lining like this at helmets of type-VII with an upwards pivoting 



face-guard, no rivet head would block the visor. As this system also appears at helmets with 



a full, not articulated visor or at helmets of type -III, there might also be a different, yet 



unknown explanation. 



All linings attached in one of the aforesaid ways could be replaced more or less easily. The 



armourer obviously intended to allow a comfortable exchange or repairing of worn out 



linings. Opening rivets for the detachment of the lining would have been time consuming 



and expensive, as the old rivets could not be used again. The leather strap was perforated at 



its lower edge by small holes, before it was riveted to the helmet. Sewing the fabric to the 



leather or plate strap was easily done with the help of a bend needle or a pig’s bristl e. No 



armourer’s skills were necessary for this work. 



The fifth lining-attachment requires the opening of all rivets for the replacement of the lining. 



In some cases, the linen-fabric of the lining had been riveted directly to the plate just above 



the ears [ref_arm_2113]. At the helmet [ref_arm_1710] this way of lining-attachment is most 



likely not the genuine arrangement. The helmet once had a visor with a f orehead reinforce.



This is traceable by the pivot holes at the skull and the corrosion marks at the forehead which 



follow the lines of the integrated reinforce of the lost visor. The rivets of type-a, holding now 



the lining, are most likely not those of the helmet’s production time, as two rivets of type-b 



survive at the right side of the skull. These probably once held the chin -strap. Interiorly the 



washers at these rivets still remain. It is very likely that all the rivets covered by the closed 



visor were indeed of type-a, whereas the visible ones originally were of type b, holding an 



interior lining leather -strap. At some unknown later time, the qualitatively very crudely 



worked and unpadded present-day lining was attached. Also the velvet lining of the h elmet 



[ref_arm_1418] is probably not of the production time of the helmet. It is riveted directly to 



the edge of the brim. Above the ears, the helmet has circumferential rivets – probably these 



once held the genuine lining.
S. 121 · Sprachlich überarbeitet · Entwurf

4.2.6.1.4 Hands

An inner glove attached to the plates provides a straightforward means of retaining hand protection. Individually plated fingers require such a glove to function. Many images show leather or textile gloves inside the plates, including [ref_ill_art_5224] PDF. In [ref_ill_art_5210] PDF, a complete glove cannot be identified, but a red lining is visible between hand and plate. Simpler or one-piece defences may have used only a strap and buckle. Simple fingerless gloves also appear to have existed [ref_ill_art_5331] PDF.

The gloves were made from leather or plant-fibre fabric, and few survive. Churburg again preserves the largest group [ref_arm_1096] PDF [ref_arm_1142] PDF [ref_arm_1150] PDF [ref_arm_1165] PDF [ref_arm_1167] PDF [ref_arm_1258] PDF [ref_arm_1259] PDF [ref_arm_1301] PDF. Examples in other collections also retain linings probably dating from their period of use [ref_arm_1061] PDF [ref_arm_1202] PDF [ref_arm_1296] PDF [ref_arm_4904] PDF.

Originalwortlaut vergleichen
4.2.6.1.4 Hands 



Hand-protections are easily fastened to the hand via a glove fixed to the plates. Hand -



protections with single protected fingers will only work with such a lining. On many 



depictions an interior leather or fabric glove is shown, e.  g. on [ ref_ill_art_5224]. In the 



painting [ ref_ill_art_5210] it is not clearly visible if the depicted hand -protections are 



equipped with a glove, but a red lining can clearly be seen in between the hand and the plate. 



Simpler or one-piece hand-protections might have been fastened with a strap and a buckle 



only. Also simple, fingerless gloves seem to have existed [ref_ill_art_5331]. The gloves were 



either made of plant -fiber fabric or of leather. In only a few cases these linings do survive. 



Also here the Churburg Armoury preserves the largest number of all  existing examples 



[ref_arm_1096] [ ref_arm_1142] [ ref_arm_1150] [ ref_arm_1165] [ ref_arm_1167] 



[ref_arm_1258] [ref_arm_1259] [ref_arm_1301]. Also items of other collections still retain 



a lining, most likely from the times when the armour was in use [ ref_arm_1061] 



[ref_arm_1202] [ref_arm_1296] [ref_arm_4904].
S. 121 · Sprachlich überarbeitet · Entwurf

4.2.6.1.5 Neck

Neck protection requires padding to prevent a frontal blow from driving the plate directly against the chin. All original Type I and II neck defences had linings, most now lost. The exception is Type II protection used exclusively with visored Type VI helmets [ref_arm_3065] PDF, since it lay outside an already enclosing, padded helmet.

Only two neck-defence linings survive from the period of use, on [ref_arm_3059] PDF and [ref_arm_3201] PDF. Both are linen padded with plant fibres.169 The lining was generally sewn to leather riveted inside the uppermost edge. On Type II, a second band along the lower edge of the chin plate could provide an additional attachment; rivets and leather remains survive there on [ref_arm_3157] PDF. Alternatively, small holes along the upper lame suggest direct stitching to the plate [ref_arm_3076] PDF.

Type II neck protection with a sight or ventilation slit in the upper lame never has lining holes in that lame. Internal examination shows that the lining was instead sewn to leather at the upper edge of the chin plate [ref_arm_3133] PDF. Some examples with an articulated upper lame but no slit apparently used the same arrangement [ref_arm_3082] PDF [ref_arm_3106] PDF. Small edge holes on the chest-covering plates of some neck defences suggest that these too may have been lined [ref_arm_3141] PDF [ref_arm_3100] PDF.

Originalwortlaut vergleichen
4.2.6.1.5 Neck 



A neck-protection only makes sense if it is fitted with a padded lining. Without a thick 



padding, a fronta l blow would make the plate hit the chin directly. Each genuine neck -



protection of type -I and -II had a lining, but most of them are lost. Only the type -II neck-



protections used exclusively together with visored helmets of type -VI [ ref_arm_3065] 



needed no lining, as they were worn exteriorly on an entirely closed and padded helmet. The 



only two existing neck -linings from the time the armour was in use are found at 



[ref_arm_3059] and [ ref_arm_3201]. Both are made of linen, padded with plant -fibers.169 



The lining was usually sewn to a leather strap which itself was riveted to the interior of the 



most upper edge. At neck-protections of type-II, the lining could additionally be sewn to a 



second leather strap, riveted to the lower edge of the chin plate. At the item [ref_arm_3157], 



rivets with rests of leather remain at this edge. Alternatively, at some objects the lining was 



possibly directly stitched to the plate, as the row of small holes at the upper lame suggests 



[ref_arm_3076]. Type-II neck-protections with a vision- or ventilation-slit at the upper lame 



never show holes for the attachment of a lining. A look at the interior makes clear that at 



these items the lining was sewn to a leather strap at the upper edge of the chin -plate 



[ref_arm_3133]. Also at some other necks with an articulated upper lame, but without a slit, 



the lining seems to have been fastened this way [ref_arm_3082] [ref_arm_3106]. The thorax-



protecting plate of some neck -protections might have had a lining too, as the small holes 



along the edge of some plates suggest [ref_arm_3141] [ref_arm_3100].
S. 122 · Sprachlich überarbeitet · Entwurf

4.2.6.2 Exterior coverings

Contemporary documents show that helmets were sometimes covered with textile as early as the fourteenth century.170 A source from the first half of the fifteenth century mentions a velvet-covered breastplate and helmet.171 The miniature [ref_ill_art_5222] PDF suggests how a suit of textile-covered armour might have looked around 1440.

Covering ridged or embossed armour is difficult: the textile must be drawn into the recesses with rivets or adhesive. A helmet of about 1510 in the BNM, accession number W4896, has a glued red-velvet covering. The covering on [ref_arm_1745] PDF was probably both glued and riveted, since it still fits closely and even detached-looking fragments remain in place.

The earliest surviving textile-covered armour object is the breastplate [ref_arm_3698] PDF, whose red velvet is secured by hundreds of rivets. Many other objects were certainly once covered, as indicated by textile remains [ref_arm_3734] PDF, rivets [ref_arm_1336] PDF, or otherwise unexplained rivet holes [ref_arm_1702] PDF [ref_arm_1729] PDF. Several Type V helmets retain velvet [ref_arm_2142] PDF [ref_arm_2126] PDF [ref_arm_4373] PDF, but their Renaissance- or Baroque-style copper-alloy ornaments suggest that these coverings may have been added in the sixteenth or seventeenth century.

A painting of St George in full armour, dated to about 1430 and held in the DIA [ref_ill_art_5162] PDF, shows a white textile or leather breastplate covering. Small metal-tipped laces secure it around the edges, with only the lance rest projecting through. This covering was clearly intended to be easily removable.

Originalwortlaut vergleichen
4.2.6.2 Exterior cover 



Contemporary documents tell that already in the early 14 th century helmets occasionally 



were covered by fabric.170 A source of the first half of the fifteenth century speaks of a velvet 



covered breastplate and a helmet. 171 The miniature [ref_ill_art_5222] shows what a suit of 



fabric-covered armour of about 1440 might have looked like.  



It is difficult to exteriorly cover armour decorated by ridges or other embossing. The fabric 



would have to be spanned into the “valleys” with the help of rivets or by means of a glue. 



There is a helmet of about 1510 in th e BNM (acc. no. W4896) with a glued cover of red 



velvet. Probably also the cover of the helmet [ ref_arm_1745] is glued and riveted, as it is 



still very close fitting and even fragments remained in place. 



The oldest example of a fabric -covered armour-part is the breastplate [ ref_arm_3698]. The 



red velvet is riveted to the plate by hundreds of rivets. A large number of other objects once 



has certainly been cove red exteriorly, as fabric -remains [ ref_arm_3734] rivets 



[ref_arm_1336] or the functionless rivet -holes suggest [ ref_arm_1702] [ ref_arm_1729]. 



Several helmets of type -V [ ref_arm_2142] [ ref_arm_2126] [ ref_arm_4373] still retain a 



velvet cover, but these could have been applied at later times in the 16 th or 17th century – 



judging by the renaissance- or baroque-style copper alloy applications at these helmets. 



In the DIA there is a painting of Saint George in full armour from about 1430 



[ref_ill_art_5162]. His breastplate is covered with white fabric or leather which is laced all 



around the edges by sm all bands that have metal points at their ends. Only the lance rest 



sticks through the cover. It is clear, that this cover was meant to be taken off easily.
S. 122 · Sprachlich überarbeitet · Entwurf

4.2.6.3 Copper-alloy attachments

Decorative copper-alloy attachments occur on some of the earliest surviving plate armour. Sometimes only otherwise unexplained rivet holes indicate their former presence. The following discussion considers their purpose, development and manufacture. The quality of the decorated objects and their presumably high cost suggest that they were made for wealthy combatants, probably of knightly status, rather than ordinary infantry.

Originalwortlaut vergleichen
4.2.6.3 Copper alloy applications 



Already some of the earliest extant plate armour is decorated by ornamen tal copper alloy 



applications. In some cases, only functionless rivet holes testify of the former attachment of 



applications. In the following, the purpose, the origin, the genesis and the production 



techniques of such applications will be examined. Due to the presumable high price and the 



good quality of all objects decorated with copper alloy ornaments, it can be postulated that 



all of them are made for the well situated, probably knightly fighters and not for the simple 



infantrymen.
S. 122–123 · Sprachlich überarbeitet · Entwurf

4.2.6.3.1 Purpose

Bands fitted over outer plate edges increase their radius, much like a turned edge, and may have helped prevent cuts. Copper-alloy attachments could also be purely decorative or convey a message. The leopard on Edward of Woodstock’s hand defence [ref_arm_1303] PDF refers both to his coat of arms and to qualities associated with the animal, such as speed, strength, power and dignity. The fragments on [ref_arm_1265] PDF bear a biblical inscription.172

The residual bluish colour of several early objects suggests that their metal surfaces may originally have been blued [ref_arm_1251] PDF [ref_arm_1259] PDF [ref_arm_1278] PDF173 [ref_arm_1280] PDF174 [ref_arm_1298] PDF [ref_arm_1301] PDF [ref_arm_1265] PDF.175 This would have contrasted with the polished, and possibly gilded, copper-alloy ornaments. A similar effect may have been intended on later fifteenth-century objects combining these attachments with embossed plates.

On [ref_arm_2126] PDF and [ref_arm_2142] PDF, surviving red textile contrasts with the yellowish metal decoration, although the date at which the bands were fitted to the covered helmets is uncertain. Overall, copper-alloy attachments were chiefly decorative: they added weight without performing an indispensable structural or protective function.

Originalwortlaut vergleichen
4.2.6.3.1 Purpose 



Where straps are attached to the outer edges of armour, they enlarge the radius similarly to 



a turned edge, thus their function could have been to prevent injuries to the wearer by cuts 



from the plate edge. Copper alloy applications can furthermore simply intend to decorate the 



item, but some of them also transfer a message: e. g. the leopard at Edward of Woodstock’s 



hand-protection [ref_arm_1303] refers to its owners coat of arms and to his virtues being the 



same like those of the animal: speed, strength, power, dignity etc.; the copper alloy fragments 



on [ref_arm_1265] have a verse of the bible inscribed.172 Due to the still bluish appearance,



it is possible that the earl y items [ ref_arm_1251] [ ref_arm_1259] [ ref_arm_1278]173 



[ref_arm_1280]174 [ref_arm_1298] [ref_arm_1301] [ref_arm_1265]175 formerly had a blued 



surface that made a colorful contrast to the maybe gilded, but certainly polished copper alloy 



applications. The same effect can be presumed for objects of the second half of the 15 th 



century which show decorative copper alloy applica tions and ridges or other embossing at 



their main plate. For example at the objects [ref_arm_2126] [ref_arm_2142] the extant fabric 



cover of red color was m eant to contrast with the yellowish copper alloy ornaments. 



Nevertheless, in all the aforesaid cases it is not sure when the decorative straps had been 



attached to fabric -covered items. In summary, it can be established that the character of 



copper alloy a pplications is merely of a decorative nature, as they bring an unnecessarily 



additional weight to the armour while fulfilling no indispensable constructional or defensive 



task.
S. 123–124 · Sprachlich überarbeitet · Entwurf

4.2.6.3.2 Development

Yellowish attachments appear in hundreds of contemporary images throughout Europe and across the period studied [ref_ill_art_5211] PDF (description 3) [ref_ill_art_5220] PDF [ref_ill_art_5217] PDF [ref_ill_art_5221] PDF. Their absence from surviving segmented armour is striking. The earliest copper-alloy ornaments on plate armour date from the 1360s. The Churburg suit [ref_arm_4098] PDF is perhaps the best-known representative of this expensive early decoration and the most complete surviving ensemble of its period. The few other similarly decorated pre-1400 objects are likewise attributed to northern Italy. Type IV helmets used between 1390 and 1420 form the largest group with decorative bands.

The right-hand defence [ref_arm_1303] PDF of the pair [ref_arm_1263] PDF [ref_arm_1303] PDF has a gilded cast copper-alloy leopard over the little-finger knuckle. All eight finger knuckles probably once carried the same figure. These hand defences are unique in being made entirely from gilded copper-alloy sheet.

Few decorated objects survive from between 1420 and 1460. The only examples related to the earlier group by their ornamental technique are [ref_arm_117] PDF and [ref_arm_879] PDF, probably Italian work of the 1460s.176 Traces of punched decoration remain on iron bars along their lower edges, where a turned edge would normally be expected.

Judging solely from surviving objects, Italian armourers appear subsequently to have abandoned copper-alloy decoration, except on the textile-covered helmets already mentioned.177 A rare mid-fifteenth-century Type III helmet [ref_arm_1354] PDF has pierced copper-alloy bands around the brim, held between the plate and an iron band with rope-like decoration. It is attributed to Burgundy, but depictions are rare and neither it nor comparable examples [ref_arm_1397] PDF [ref_arm_1424] PDF [ref_arm_4197] PDF bears a mark. The attribution therefore remains tentative.

A distinct group of Type III helmets frequently attributed to Spain has a broad copper-alloy band around the skull at ear level, generally gilded and engraved with acanthus scrolls or inscriptions. These helmets most probably date from 1470–1500. No other Spanish armour type is known with such bands.

German armourers began using copper-alloy ornament in the 1470s. Cast attachments continued to occur occasionally on armour made in German-speaking regions until the late fifteenth century.178 They then appear to have given way to etched and gilded decoration applied directly to iron or steel.

Redaktionelle Hinweise · 2
  • Die Datierung „until the late 15th century“ wurde erhalten. Anm. 178 nennt dagegen Beispiele von etwa 1514 und 1557; Haupttext und Fußnote sind zeitlich nicht deckungsgleich. Bei fachlicher Revision klären.
  • Die Beurteilung eines Rückgangs italienischer Metallauflagen beruht ausdrücklich auf erhaltenen Objekten; die abweichende Bildüberlieferung in Anm. 177 bleibt erhalten.
Originalwortlaut vergleichen
4.2.6.3.2 Genesis 



It can be anticipated that yellowish applications are depicted in hundr eds of contemporary 



artworks all throughout the considered period and everywhere in Europe [ ref_ill_art_5211] 



(descr. 3) [ref_ill_art_5220] [ ref_ill_art_5217] [ ref_ill_art_5221]. The lack of decorative 



copper alloy straps on segment-armour pieces is noticeable. The earliest examples of copper 



alloy applications are found at plate armour from the 1360ies onwards. Maybe the most 



prominent substitute for the earliest costly decorated armour is the Churburg suit 



[ref_arm_4098], which is also the most complete extant ensemble of the time. The few other 



similarly ornamented plate armour items from before 1400 are all just as well attributed to 



northern Italian production. The largest group of items decorated with bands consists of 



helmets of type -IV , in use between 1390 and 1420. On the right hand -protection of pair 



[ref_arm_1263], [ref_arm_1303] at the small finger knuckle embossing a gilded cast copper 



alloy leopard is attached. It is likely that all eight finger knuckles once were highlighted by 



the same figure. These hand -protections are unique in being made entirely from gilded 



copper alloy plate.  



Only few items with copper alloy applications of the years between 1420 and 1460 can be 



found. The only items of this period related to the aforesaid examples by the decoration 



technique are [ref_arm_117] and [ref_arm_879] – probably made in Italy in the sixties of the 



15th century.176 The remains of ornaments punched into the surface are found here at the iron 



bars at the lower edge – where normally a turned edge would be expected.



In the following years – again only according to extant 177 armour parts – the Italian 



armourers seem to have stopped the decoration of their products with copper alloy 



applications completely, with the exception of the aforesaid fabric covered helmets.  



A rare mid-15th century helmet of type -III [ref_arm_1354] has fretwork decorated copper 



alloy bands attached to the brim. It is sandwiched between the plate and a roped band , the 



latter made of iron. This helmet is attributed to Burgundian origin, but as depictions are rare 



and – together with the similar objects [ref_arm_1397] [ref_arm_1424] [ref_arm_4197] – it 



bears no mark, this provenance remains a vague suggestion. A special group of type -III 



helmets, frequently attributed to Spanish production, often has a broad circumferen tial 



copper alloy band attached in the height of the ears. It is usually gilded and decorated by 



engraved acanthus-twines or inscriptions. These helmets are most likely made in the years 



between 1470 and 1500. No other Spanish armour-type is known to have been decorated by 



copper alloy straps.  



From the 1470ies on, also the German armourers began to decorate their products with 



copper alloy ornaments. Armour made in the German speaking lands continued to be 



occasionally decorated by cast copper alloy applic ations until the late 15 th century.178 It 



seems like from then on the copper alloy ornaments were replaced by etched and gilded 



decorations directly applied to the iron or steel surface.
S. 124–125 · Sprachlich überarbeitet · Entwurf

4.2.6.3.3 Manufacturing techniques

Attachments are generally secured with iron or copper-alloy rivets. Only the suit [ref_arm_3258] PDF, at its knees [ref_arm_2699] PDF and breastplate [ref_arm_3615] PDF, has bands fastened with screws. On [ref_arm_1354] PDF, riveting was supplemented with tin solder.

Only [ref_arm_3241] PDF has plain, undecorated sheet-metal bands. Elsewhere, attachments carry relief ornament or patterns embossed, engraved or punched into their surfaces. On [ref_arm_1259] PDF, the engraved and punched decoration continues from the copper-alloy bands onto the iron plate.

All surviving copper-alloy attachments ultimately derive from casting. One method produces the finished form directly;179 another produces stock that must be shaped and decorated further. In the latter, a cast billet is forged into sheet or the required profile [ref_ill_art_5314] PDF, then finished cold. Specialist suppliers probably provided such bands, leaving the armourer to fit and decorate them with familiar tools and skills.

Relief could be worked from behind with chisels, supporting the metal on lead laid over the bench or anvil. Ornament and inscriptions were then engraved or chiselled and polished. Some works by Caspar Rieder of Innsbruck have openwork cut directly into copper-alloy bands [ref_arm_1096] PDF [ref_arm_1142] PDF. Fragments of comparable pierced bands survive on two hand defences by an unidentified maker [ref_arm_1063] PDF [ref_arm_1081] PDF. The objects most probably share a workshop; at least their identical band patterns indicate the same source for the decoration. These forms are simple enough to have been cut from sheet. Pierced bands generally follow turned plate edges.

Ornaments cast directly to shape were probably made by a specialist rather than the armourer. Once an object was complete, it may have gone to a goldsmith or another craftsperson experienced in copper-alloy casting. Wax models could be fitted precisely to its curves before lost-wax casting. The leopards on [ref_arm_1303] PDF were probably made this way. Surviving original objects suggest that the technique was practised chiefly in Augsburg during the final third of the fifteenth century [ref_arm_3258] PDF. All these examples are attributed to Lorenz or Jörg Helmschmied’s workshop.

Originalwortlaut vergleichen
4.2.6.3.3 Techniques 



In most cases, the applications are attached by means of iron or copper alloy rivets. Only the 



suit [ref_arm_3258] at the knees [ref_arm_2699] and at the breastplate [ref_arm_3615] has 



the bands fixed by screws. At [ ref_arm_1354] they had been riveted and embraced by tin 



solder.  



Only at the suit [ ref_arm_3241] the copper alloy applications are plain, undecorated straps 



of plate. In all other cases, the decorations form either a pattern in relief or ornaments are 



embossed, engraved or punched into the surface. In the case of [ref_arm_1259] the engraved 



and punched decoration of the copper alloy straps extends also to the surface of the iron -



plate.  



All copper alloy applications to be found on extant plate armour are based on casting 



techniques. The difference between the techniques is that one allows the direct final shaping 



of the object179, while the other one produces only the basic material that needs to be shaped 



and/or decorated by further treatment. In the latter case a billet is cast and subsequently



forged into a strap of plate or into the desired profile [ref_ill_art_5314], which subsequently 



could be further treated by cold work. The straps produced by such a technique were most 



likely supplied by specialized craft-branches and in the armourer’s workshop they got only 



adjusted and decorated. The necessary skills and tools were those of the armourer’s everyday 



business. The bands were embossed by chiseling the patterns from the interior. A block of 



lead was placed in between the metal and the workbench or anvil. Subsequently the 



ornaments and inscriptions were engraved or chiseled and polished.  Some works of Caspar 



Rieder of Innsbruck are decorated with copper alloy bands with open -work pattern, simply 



cut into a plate -strap [ ref_arm_1096] [ ref_arm_1142]. At other items of an anonymous 



master, fragments of fretwork-decorated bands do survive [ref_arm_1063] [ref_arm_1081]. 



Most likely these two hand -protections come from the same workshop. At least the same 



workshop made the copper alloy bands as the pattern is identical. Also the shape of these 



straps is simple enough to have been cut from a plate strap. The copper alloy bands decorated 



by fretwork are usually attached along turned plate-edges. 



The cast ornaments have most likely not been made by the armourer himself. The technique 



demands a high degree of specialization. After the armourer had finished his product, he 



probably gave it to a goldsmith or another craftsman capable of casting copper alloys. This 



worker then designed the desired applicatio ns in wax and fitted them exactly to the curves 



of the armour part before they were cast by the lost -wax technique. The leopards at 



[ref_arm_1303] had most likely been cast by this method. Judging by the existing genuine 



items, it seems like mainly in Augsburg in the last 3 rd of the 15th century applications were 



produced by this technique [ref_arm_3258]. All of these items are attributed to the workshop 



of either Lorenz or Jörg Helmschmied.
S. 125–126 · Sprachlich überarbeitet · Entwurf

4.2.6.3.4 Reproduction ornaments on original armour

The suit [ref_arm_4141] PDF has attracted little scholarly attention because it was regarded as wholly reproduced. Probably made by Winkelmayer in Vienna,180 it was acquired by the BMA as a reproduction. Closer examination nevertheless identifies its helmet as an original example of the rare Type VII “black sallet” group [ref_arm_1702] PDF. Some characteristic small holes along its unturned lower edge now secure copper-alloy ornaments matching the rest of the suit. Apparently, its plain appearance was considered insufficiently impressive for the assembled knightly armour, prompting the addition of gold-coloured decoration.

Plain bands were similarly added to the helmet, armpit, neck, hand and knee protection of [ref_arm_3241] PDF. James Mann suggested that the Nuremberg dealer Pickert arranged its completion and decoration after acquiring the full panoply from Hohenaschau Castle in 1861.181 The hand defences [ref_arm_1045] PDF [ref_arm_1109] PDF are reproductions.182 Plain bands of a similar appearance are nevertheless documented in contemporary art [ref_ill_art_5155] PDF.

Some bands on [ref_arm_3236] PDF are also replacements. Bashford Dean writes “that six of the original latten bands are still present”183 and illustrates four decorative patterns, but does not distinguish the original bands from the replacements. This cannot be resolved without closer examination. The bands on the unrelated hand-defence pair [ref_arm_1037] PDF [ref_arm_1163] PDF may likewise have been reproduced on his instructions.

The suit [ref_arm_3244] PDF appears to combine objects that did not originally belong together. Bands with roughly pierced ornament were added to the helmet, neck, breastplate, front hip protection, backplate, elbows and hands, apparently to conceal their disparate origins.

Even securely original, high-quality armour in Vienna carries replacement bands. Those on [ref_arm_1927] PDF were added in the nineteenth century to make the helmet match a Helmschmied suit.184

Originalwortlaut vergleichen
4.2.6.3.4 Reproduced ornaments on genuine armour 



The suit [ref_arm_4141] has been ignored by scholars so far, as it was thought to be entirely 



a reproduction. The suit was probably made by Winkelmayer in Vienna180 and it was bought 



by the BMA as a reproduction, but a closer look reveals that the helmet is actually a genuine 



example of the rare “black sallet” type-VII helmets [ref_arm_1702]. Some of the small holes 



at the lower edge – typical for this helmet-model – are now used for the fastening of copper 



alloy applications of the same type found at other parts of this suit. The edges of this helmet 



had never been turned and thus its simple appearance did – in the eye of the former restorer 



or reproducer – not fit to the knightly suit. Therefore, an un-knightly helmet had gained some 



dignity by the attachment of golden colored applications. 



For the same reason, the plain copper alloy bands were attached to the helmet, armpit, neck, 



hand and knee protections of suit [ ref_arm_3241]. James Mann suggested that the 



Nuremberg art dealer Pickert, who in 1861 had acquired the full panoply from the a rmoury 



at Hohenaschau castle in Bavaria, had arranged for the completion and decoration of the 



equestrian armour.181 The hand-protections of this suit [ ref_arm_1045] [ref_arm_1109] are 



reproductions.182 Nevertheless, similar, undecorated bands are depicted in several 



contemporary artworks [ref_ill_art_5155].  



Some of the copper alloy straps of suit [ref_arm_3236] are reproductions. Bashford Dean in 



his description of this suit states “that six of the original latten bands are still present” 183



and gives a drawing of four different types of decoration s found on these bands. 



Unfortunately he does not say which of the current bands are replaced and which are genuine. 



Without a closer examination this remains impossible to tell. At the pair of hand-protections 



[ref_arm_1037] and [ref_arm_1163] – not belonging to the aforesaid suit – the bands were 



maybe also reproduced on Bashford Dean’s instructions.  



The suit [ref_arm_3244] seems to be composed of different items that once did not belong 



together. To cover this spot of bother, copper alloy bands were attached to the edges of the 



helmet, the neck, the breastplate, the front of the hips, the backplate, the elb ows and the 



hands. The straps are ornamented by crude fretwork.  



Even at the precious and certainly genuine armour in Vienna reproductions of bands 



attached. The applications at [ref_arm_1927] were attached in the 19th century to match the 



helmet to one of Helmschmied’s suits.184
S. 126–129 · Sprachlich überarbeitet · Entwurf

4.2.6.3.5 Lorenz Helmschmied’s work in Vienna

The copper-alloy decoration on armour attributed to Lorenz Helmschmied merits detailed discussion for its craftsmanship and influence on later reproductions. Most field-armour objects attributed to his workshop have, or once had, bands riveted along selected overlapping or outer edges.

Only objects in the HJRK in Vienna appear to combine his mark with these characteristic bands. Unmarked objects elsewhere are generally attributed to his workshop because of comparable bands or other similarities. Some marked works have lost their bands [ref_arm_3214] PDF, while others lack attachment holes and evidently never carried them [ref_arm_3243] PDF [ref_arm_3695] PDF.

Nineteenth-century restoration certainly altered the Vienna objects. Cleaning and refurbishment probably preceded Wendelin Boeheim’s opening of the collections to the public in 1889.185 Some ornaments had already been lost or detached: delicate copper-alloy rivets may have failed through handling, or bands may have been removed for cleaning or recycling. Restoration would have involved refitting surviving ornaments and replacing missing ones to unify the reassembled suits.

Six principal constructions and designs occur. All incorporate rope-like ornament, but its form varies between objects.

1. A flat pierced band beneath a separate roped band. The lower band forms a row of fleurs-de-lys whose side petals meet, leaving heart-shaped openings. A small recessed wedge lies at the base of each motif. The relief resembles contemporary Gothic architectural tracery.186 Thin copper-alloy rivets generally pass through plate, pierced band and roped band in that order. Each band follows the plate’s curves closely.

At curved or pointed ends and beneath large rivet heads, the pattern broadens into more elaborate ornament or changes to a simpler form. These transitions suggest that this and the second design came from the same workshop. On [ref_arm_1246] PDF, the band ends in a convex arc rather than a fleur-de-lys; on the leg-defence pairs [ref_arm_2819] PDF [ref_arm_2818] PDF [ref_arm_2479] PDF [ref_arm_2480] PDF, it ends in four such arcs.

Even in Vienna, the originality of many bands remains uncertain because excellent copies were made for at least [ref_arm_1927] PDF. Filed lines are visible through the openings of the bands on the breastplate’s pelvic lames [ref_arm_3615] PDF. Comparable filing survives at the lowest pelvic edge of the backplate [ref_arm_3302] PDF. These may be traces of embossed roping hammered flat before 1584.187 The lines remain conspicuous, with no apparent attempt to remove them completely. If these edges were originally embossed, bands are unlikely to have been fitted from the outset. The backplate also lacks band-attachment holes, casting further doubt on the corresponding breastplate decoration. The originality of related bands therefore cannot simply be assumed.

The hand defence [ref_arm_4904] PDF, recorded in an 1845 inventory of Freiburg’s Bürgercorps armoury,188 offers an independent comparison. Its bands were removed and refitted with inappropriately large-headed iron rivets. The same rivets retain the inner glove, making alteration during the period of use very likely. The bands are therefore unlikely to be reproductions. Their close resemblance to some Vienna examples supports the latter’s originality. The effigy of Jörg von Waldburg [ref_ill_art_5366] PDF (description 1) provides further evidence: its armour has fleur-de-lys borders and roped bands closely resembling Helmschmied’s work.

2. A band of adjoining convex arcs beneath separate roping. This is simpler than the fleur-de-lys pattern and has surface ornament but no pierced work. Each arc on the elbow pair [ref_arm_35] PDF [ref_arm_38] PDF bears a C-shaped punch. Identical bands on the hand-defence pairs [ref_arm_1209] PDF [ref_arm_1247] PDF and [ref_arm_1245] PDF [ref_arm_1272] PDF carry more detailed groups of punched lines resembling a mandarin segment. No other comparable objects were found. The examples are confined to hands and arms, apart from the related bands noted under 5 in the original account.

3. Roped bands and their variants. These generally alternate broad, flat, twisting fields with narrow rows of stylised beads. On at least two objects, roping occurs without a lower decorative band. For [ref_arm_3613] PDF, Thomas and Gamber suggest that the bands came from [ref_arm_3611] PDF, perhaps removed around 1495 when attached thigh protection was added.189 They could instead derive from a lost breastplate or backplate, or be nineteenth-century reproductions. A lost pierced band may once have accompanied them: fine openwork at the centre of the lowest pelvic lame seems inconsistent with an otherwise plain border.

The helmet [ref_arm_1971] PDF also has a single roped band at its lower edge, beside gilded ornament on a blue ground.190 The yellowish metal contrasts with the blue. Convex arcs on some overlapping edges, including at the nape-guard pivots, suggest that an arc-shaped band may once have accompanied the roping. A comparable arrangement survives on [ref_arm_1245] PDF [ref_arm_1272] PDF. Their close decorative relationship suggests possible association within a suit or “Garnitur”, or at least manufacture in Lorenz or Jörg Helmschmied’s workshop.

The roping varies substantially. On [ref_arm_1209] PDF [ref_arm_1247] PDF and [ref_arm_1245] PDF [ref_arm_1272] PDF, it is described as formed in one piece with convex arcs and accompanied by a narrow parallel beaded row. On [ref_arm_1059] PDF [ref_arm_1124] PDF, the flat tapering fields are narrow and the intervening bead rows steeply inclined. On [ref_arm_1208] PDF [ref_arm_1246] PDF, the fields are broader and untapered, with shallower bead rows, producing less pronounced relief. The excavated helmet [ref_arm_1734] PDF, outside Vienna, has a similar fleur-de-lys band but different roping: very broad, untapered fields alternate with three narrow unbeaded bands. Its recent excavation establishes that it is not a reproduction.

4. Roping and convex arcs formed together. The bands on [ref_arm_1244] PDF [ref_arm_1207] PDF resemble the second design but combine its elements in one piece. The arcs lack surface ornament apart from rough, asymmetrical filed lines. The flat roping fields are very broad, and the narrow intervening spiral band is unbeaded.

5. Fine roping formed in one piece with fleurs-de-lys. Bands on the abdominal portions of the front and back protection, knees and neck of the Vienna suit [ref_arm_3258] PDF differ from other examples attributed to Lorenz Helmschmied. Their finer roping resembles two twisted wires. No other breastplate or backplate has comparable bands in these positions, raising questions about originality. Of the four breastplate bands, the attachments nearest the centre are screwed, whereas those at the sides are riveted. The bands on its lowest pelvic lame are also screwed, although constructed like design 1. Elsewhere, the decorative bands are riveted.

6. Roping represented by incised lines. The elbow [ref_arm_35] PDF has single sheet-metal bands broadly resembling design 2, but with the rope pattern only engraved. Its counterpart [ref_arm_38] PDF has convex arcs beneath separate roping. The difference is unexplained although the elbows appear to form a pair. Perhaps [ref_arm_35] PDF lost its roped band, prompting a restorer to file an imitation into the surviving lower band.

Redaktionelle Hinweise · 3
  • Das Original verweist am Ende von Gruppe 2 auf Gruppe 5 und spricht dabei erneut von Handpanzerung; Gruppe 5 beschreibt jedoch Rumpf, Knie und Hals. Verweis nicht stillschweigend umnummeriert.
  • Dieselben Handobjekte werden in Gruppe 2 als mehrschichtig und in Gruppe 3 als einteilig beschrieben. Beide Beschreibungen bleiben sichtbar; Konstruktion anhand der Objekte klären.
  • Die Verbindung des Helms mit den Handobjekten bleibt eine aus Ornamentähnlichkeit abgeleitete Hypothese, keine bestätigte Ensemblezuordnung.
Originalwortlaut vergleichen
4.2.6.3.5 Lorenz Helmschmied’s works in Vienna 



Due to their elaborate craftsmanship and the influence they had on many reproductions, the 



decorative copper alloy attachments on the armour part s of Lorenz Helmschmied must be 



discussed here in detail. Most of the field armour parts attributed to his workshop typically 



have or had copper alloy straps riveted at chosen edges. They do either appear at overlapping, 



but also at outer plate edges.  



It seems like only armour from the HJRK in Vienna bears both together, Lorenz 



Helmschmied’s mark and the typical ornamented bands. Unmarked items in other collections 



are usually ascribed to his workshop whenever they bear bands similar to the Vienna 



examples or show other similarities to his works. Some items are indeed marked by him, but 



they lack the typical straps as they either got lost [ref_arm_3214] or had never been attached 



[ref_arm_3243] [ref_arm_3695] (no rivet-holes are visible). 



Restorations of the 19th century certainly altered the genuine appearance of the Vienna items. 



The objects had to be cleaned  and refurbished for display, probably before 1889, when 



Wendelin Boeheim opened the collections for public. 185 Parts of the applications had until 



then certainly been lost or detached, probably due to inappropriate handling throughout the 



centuries to which the copper alloy rivets did not resist. They might have been taken off for 



cleaning or for the recycling of the valuable material. The presumed restoration of the 19 th 



century had to replace what still existed and to complete what was lost to finally achi eve a 



uniform appearance of the reassembled suits. 



Basically six types of bands, different in construction and design do appear on 



Helmschmied’s products. All of these include a band of roped decoration, which varies in its 



design from object to object. 



1. In the first case, under the roped strap a flat band with fretwork-like cutouts is sandwiched. 



This band forms rows of fleur-de-lys symbols, touching each other with the point of the side-



leafs, leaving heart-shaped penetrations in the bands. At the base of each fleur-de-lys, a small 



gore is undercut into the surface. The profile of these decorations reminds on the ‘gothic’



tracery of contemporary architecture. 186 The armour plate, the fleur -de-lys and the roped 



band are usually riveted together in the said order by means of single thin copper alloy rivets. 



The bands do follow exactly the curves of the plates. At the endings of the bands, where the 



plate edges are curved or pointed and where large rivet heads are placed upon the bands, the 



fleur-de-lys pattern changes to a wider and more decorated surface, or the pattern is changing 



to a more simple form. Here it also becomes clear that these and the decorations dis cussed 



below (2.) were most likely made by the same workshop: The bands on item [ref_arm_1246] 



are ending in a convex bow instead of the expected fleur -de-lys. At the pair of leg armour 



[ref_arm_2819] [ref_arm_2818] [ref_arm_2479] [ref_arm_2480] they are even ending in a 



row of four of such bows. As said above, even in the Vienna collection the authenticity of 



most of such extant bands is uncertain as very good copies have obviously been made for at 



least one of the Vienna objects [ ref_arm_1927]. Underneath the ornamental bands at the 



pelvis-lames of the breastplate, lines filed into the surface of the iron plate can be seen 



through the cutouts [ ref_arm_3615]. The same filing is found at the lowest pelvis edge of 



the backplate [ ref_arm_3302]. These lines are maybe the remains of an embossed roping 



that at some date before 1584 were leveled by the hammer. 187 They are visible very strong 



and it does not seem like attempts were made to grind them off completely. If the plate once 



was embossed here, it is very unlikely that bands had been attached from the beginning, 



neither at the pelvis -lames of the breast - nor at the back plate. Besides this, at the latter no 



holes for the attachment of bands are visible, so the attachment at the pelvis -lame of the 



breastplate can be challenged as being original. It is therefore impossible to tell if other bands 



of the same type are genuine at all. Nevertheless, there is one example of decorated straps in 



another collection that can serve as a hub for what might be genuine and what might be 



restoration at the Vienna items [ref_arm_4904]. This hand-protection appears already in an 



inventory of the armoury of the Bürgercorps of Freiburg written down in 1845. 188 Its 



decorative bands had been taken off and refitted at some time, as the inappropriately large -



headed iron rivet-joints suggest. These rivets also fix the interior leather glove to the plate. 



This fact makes it very likely that the alterations were carried out during the times when the 



hand-protection was still in use. Therefore, it is very unlikely that the bands are 



reproductions. As they exactly resemble the ornamented straps at certain Vienna items, they 



support the suggestion of the latter being genuine. Also the effigy of Jörg von Waldburg 



[ref_ill_art_5366] (descr. 1)  can help to identify the genuine appearance of ornamented 



bands. The edges of his armour are decorated by stripes of fleur -de-lys and a roped band – 



resembling very closely those on the works of Lorenz Helmschmied. 



2. The second type of sandwiched band  is characterized by a row of directly adjoining 



convex bows. This decoration is much simpler in comparison to the fleur-de-lys bands. The 



bands are only decorated on the surface and no example shows any fretwork decoration. At 



the pair of elbows [ ref_arm_35] [ref_arm_38] each bow is punched with a C -shaped mark. 



The identical bands at the two pairs of hand-protections [ref_arm_1209] [ref_arm_1247] and 



[ref_arm_1245] [ref_arm_1272] show a more detailed punched decorat ion of single lines, 



leaving a mark that looks similar to a wedge of a mandarin. No other objects decorated 



similarly could be found in the course of this study. It is noteworthy all examples are either



found on hand or on arm-protections. No other body protection with such a decoration seems 



to survive, with the exception of the related bands mentioned here under 5. (again on hand -



protections). 



3. Due to their design variations, in the following the different roped bands will be described 



in detail. Basica lly they are all designed by sequences of wide, plane and twisted fields 



alternating with a fine line of stylized pearls. On at least two objects these bands appear 



solely, without the sandwiched band underneath [ ref_arm_3613]. Thomas and Gamber are 



suggesting that these bands might have belonged to breastplate [ref_arm_3611], where they 



probably were taken off around 1495 for the attachment of adjacent torso leg-protections.189 



These straps could also derive from another, now lost breast - or backplate, or they are 



reproductions of the 19 th century. It is also possible that they once had a second, fretwork 



decorated strap sandwiched underneath. The fine fretwork in the center of the lowest pelvis-



lame supports this assumption – this would not match to an undecorated lower edge. The 



helmet [ref_arm_1971] at its lower edge is also decorated by a single roped band. The lower 



edge of this helmet had been decorated by gilded ornaments on a blued background. 190 The 



yellowish straps contrast nicely to the blue. As some of the overlapping plate edges, e. g. at 



the pivots of the nape-guard, are decorated by convex bows, maybe  the copper alloy bands 



also once had a bow -decorated strap riveted underneath. A constellation similar to th is is 



found at the pair of hand protections [ref_arm_1245] [ref_arm_1272]. The close relationship 



of the decoration of the aforesaid helmet and the latter objects suggest their affiliation to one 



suit or “Garnitur”, but at least to the workshops of Lorenz or Jörg Helmschmied. 



As said above, the design of the roping differs widely. The roped bands at the pairs of hand-



protections [ ref_arm_1209] [ ref_arm_1247] and [ ref_arm_1245] [ ref_arm_1272] are 



worked in one piece with a row of convex bows. They are accompanied by a parallel narrow 



row of stylized pearls. The plane, tapere d fields, e. g. of the roping at the pair of hand -



protections [ ref_arm_1059] [ ref_arm_1124], are rather narrow with the row of pearls 



alternating in a rathe r steep angle. This is different e. g. at the pair [ ref_arm_1208] 



[ref_arm_1246], where these fields are wider and the bordering pearl -bands in between are 



sloping less steep. As the bands are not tapered at their plane parts they look less plastic. 



Even though the fleur-de-lys strap underneath is very similar, the roped band at the helmet 



[ref_arm_1734] (not in Vienna) differs from all other objects decorated in this style. Here 



the very wide, also not tapered plane areas are interrupted by three narrow bands without a 



pearl-like decoration. This helmet has been excavated very recently and is therefore certainly 



no reproduction.  



4. The straps at the hands [ref_arm_1244] [ref_arm_1207] appear like those described under 



2., but the roping and the row of bows are worked in one piece. The bows are not decorated 



at the surface – only crude and asymmetrical filed lines are visible. The plane segments of 



the roping are very wide and the alternating fine twisted band is not decorated by stylized 



pearls. 



5. The straps at the abdomen parts of the breast -and the backplate, at the knees and at the 



neck of the Vienna suit [ref_arm_3258] are different from the other fleur-de-lys straps found 



at items attributed to Lorenz Helmschmied. The roping is worked in one piece with the fleur-



de-lys pattern. The roping itself is finer in diameter and the appearance is similar to two 



twisted wires. As no other breast -or backplate shows such copper alloy straps at the same 



location, the question of their authenticity has to be discussed. It is noticeable that at the four 



bands of the breastplate the two joints towards the center are screwed, while tho se at the



sides are riveted. Also the straps at the lowest pelvis -lame are attached by screws, whereas 



the bands themselves are constructed as described under 1. At all other armour parts the 



decorative bands are attached by rivets.  



6. At an elbow [ref_arm_35] single plate-bands (basically like 2.) with the rope decoration 



only engraved are attached. At the counterpart [ ref_arm_38] a strap of convex bows is 



sandwiched underneath a separate roped band. It is not clear why the bands are constructed 



different from each other, while the elbows themselves seem to make a pair. One possible 



explanation is that at [ref_arm_35] the roped band had got lost and some restorer later filed 



the roping in the remaining band to match it with its counterpart.
S. 129 · Sprachlich überarbeitet · Entwurf

4.2.6.3.5.1 Manufacturing technique

Bands on expensive armour were not simply cut to length from continuously produced stock. Their precise fit to curved edges could only have been achieved by lost-wax casting. This required allowance for metal shrinkage: wax models had to be slightly larger than the intended finished pieces. They were embedded in a clay-like material and heated until the wax burned out, leaving a heat-resistant mould. Molten copper alloy was poured in and contracted as it cooled.191

Wax bands may themselves have been cast in wooden or stone moulds carved with the required pattern. A roller pressing or cutting ornament into wax sheet is another possibility. Curves could be built into the mould or produced by warming and shaping the wax against the finished armour. A heated iron could fuse separate wax sections; special motifs cut from wax sheet could be joined in the same way. Defects were easily repaired at this stage. Reusable pattern moulds also made it possible to repeat decoration on other objects or replace a failed casting quickly.

Redaktionelle Hinweise · 1
  • Der Ausschließlichkeitsanspruch für Wachsausschmelzguss („only“) stammt aus dem Original. Keine neue experimentelle Prüfung alternativer Herstellungsverfahren vorgenommen.
Originalwortlaut vergleichen
4.2.6.3.5.1 Technique 



The straps at the more costly armour had not been cut down to the desired length from a 



meter-wise produced band. The accuracy with which they fit to the curves of the edges can 



only be achieved by lost wax casting. This technique is very difficult as the shrinking of the 



cast metal has to be considered in the wax and so the dimensions of the latter have to be 



modeled slightly larger than they are finally needed. The wax straps had to be embedded in 



some sort of clay. The subsequent oven heating let the wax burn off, leaving a heat resistible 



negative of the wax. Then molten copper alloy was poured in the mold. While cooling down, 



the metal reduced its volume.191  



The wax models might have been  cast by a strap -shaped mold of wood or stone with the 



desired pattern incised. Also some kind of roller, pressing or cutting the desired pattern into 



wax plates is conceivable. Where the straps needed to curve, either the mold might have 



been designed accordingly or the warm wax was modeled according to the curves of the 



already finished plate armour. The wax straps were probably welded together by means of a 



hot iron, melting the join t. Interruptions in the decorations might have been cut from wax 



plates and attached the same way. Damages in the decoration could easily be corrected at the 



wax. Another advantage of this technique was that the basic molds were reusable for the 



decoration of other armour pieces and in case of the failure of the subsequent casting the 



work could be repeated quickly.
S. 129 · Sprachlich überarbeitet · Entwurf

4.2.6.3.6 Ornaments on reproduction armour

The helmets [ref_arm_1857] PDF [ref_arm_1899] PDF and associated throat defences [ref_arm_5099] PDF [ref_arm_3202] PDF are reproductions. Their marks suggest late nineteenth-century manufacture by Winkelmayer in Vienna.192 The ornaments on the suits [ref_arm_3213] PDF [ref_arm_3233] PDF [ref_arm_3262] PDF [ref_arm_4080] PDF [ref_arm_4136] PDF [ref_arm_4141] PDF are likewise certainly reproduced. Apart from [ref_arm_3233] PDF, their bands imitate those on Lorenz Helmschmied’s Vienna armour.

The former Klingbeil Collection suit [ref_arm_3209] PDF reproduces the Churburg suit [ref_arm_4098] PDF, except for the left forearm defence [ref_arm_5007] PDF. Even the empty holes on the back of the hand were copied from the original.

Redaktionelle Hinweise · 1
  • Die ursprüngliche Aussage, alle aufgezählten Ensembles seien vollständig reproduziert, widerspricht dem in §4.2.6.3.4 ausdrücklich als echt beschriebenen Helm von ref_arm_4141. Hier wird nur die in diesem Abschnitt behandelte Zuschreibung der Auflagen als Reproduktionen übernommen; die Ausnahme beim Helm bleibt maßgeblich.
Originalwortlaut vergleichen
4.2.6.3.6 Ornaments on reproduced armour 



The helmets [ref_arm_1857] [ref_arm_1899] together with the appending throat protections 



[ref_arm_5099] [ref_arm_3202] are reproductions, according to the marks 192 most likely 



made by Winkelmayer in Vienna in the late 19 th century. The applications at the suits 



[ref_arm_3213] [ ref_arm_3233] [ ref_arm_3262] [ ref_arm_4080] [ ref_arm_4136] 



[ref_arm_4141] are certainly reproduct ions, as the entire suits are. With the exception of 



[ref_arm_3233], the bands at the mentioned objects are all trying to resemble applications 



on Vienna armours of Lorenz Helmschmied.  



The suit [ ref_arm_3209] of the former Klingbeil Collection is an entire reproduction, 



imitating the Churburg suit [ ref_arm_4098] – with the exception of the lower left arm 



[ref_arm_5007]. Even the empty holes at the back of the hand were copied from the original.
S. 130 · Sprachlich überarbeitet · Entwurf

4.2.6.3.7 Lost attachments

Empty rivet holes suggest that ornaments resembling those on the backs of [ref_arm_1251] PDF [ref_arm_1301] PDF once also decorated [ref_arm_1259] PDF [ref_arm_1301] PDF.

Some objects now entirely plain may once have had copper-alloy decoration. The hand-defence pair [ref_arm_1252] PDF [ref_arm_1299] PDF has small holes that may have held bands or other ornaments. A large square hole near each thumb may likewise have served a decorative attachment.

The original components of the composite suit [ref_arm_3214] PDF in the Detroit Institute of Arts were most probably decorated with cast bands. Marks on the knees identify Lorenz Helmschmied of Augsburg as the maker associated with the breastplate and backplate; the thigh defences, excluding their side plates, and the shoulders are also certainly his work. Only the breastplate lacks holes for the proposed bands. Empty holes occur where the backplate overlaps the inserted nape plate, around the knees’ shell-like extensions, and along the shoulders’ upper and lower edges.193 The lost ornament probably resembled one of the band types on his Vienna armour, such as [ref_arm_3257] PDF.

Small holes, sometimes retaining rivets, along the visor edges of [ref_arm_1540] PDF [ref_arm_1548] PDF [ref_arm_1566] PDF [ref_arm_4258] PDF may have held decorated copper-alloy bands resembling those on [ref_arm_1495] PDF. The unturned lower edge of [ref_arm_1756] PDF is likewise pierced with small holes, very probably for ornamental bands. Similar holes along the unturned lower edges of the leg defences [ref_arm_2291] PDF [ref_arm_2296] PDF [ref_arm_2325] PDF [ref_arm_2958] PDF suggest attachments comparable to those on [ref_arm_2348] PDF.

Cast bands once decorated the lowest pelvic lames of the breastplate [ref_arm_3611] PDF194 and backplate [ref_arm_3374] PDF. They may have resembled those on [ref_arm_1096] PDF [ref_arm_1142] PDF, which are approximately contemporary and bear the mark of the same maker, Caspar Rieder of Innsbruck-Mühlau.

Redaktionelle Hinweise · 2
  • ref_arm_1301 ist im ersten Satz sowohl erhaltenes Vergleichsbeispiel als auch Beispiel verlorener Auflagen. Diese Wiederholung stammt aus dem Original und bleibt zur Klärung erhalten.
  • Die Zuschreibung mehrerer Teile von ref_arm_3214 anhand der Knie-Marken ist als ursprünglicher Zuschreibungszusammenhang erhalten; daraus wird keine neue gesicherte ursprüngliche Zusammengehörigkeit abgeleitet.
Originalwortlaut vergleichen
4.2.6.3.7 Lost applications 



Applications similar to those on the back of the hands on [ ref_arm_1251] [ref_arm_1301] 



were most likely also once ornamenting [ ref_arm_1259] [ ref_arm_1301], to which the 



empty rivet holes testify. 



Some entirely undecorated items seem to have been once decorated by copper alloy 



applications. The pair of hand-protections [ref_arm_1252] [ref_arm_1299] show small holes 



that maybe once held decorative stripes or other attachments in place. At each item in the 



area of the thumbs there is a large square hole which maybe also once  held some sort of 



decoration.  



In the Detroit Institute of Art there is a composite suit of armour [ref_arm_3214], which had 



its original parts most likely once decorated by cast copper alloy bands. Accord ing to the 



armourer’s marks at the knees, the breast and the backplates are the work of the Augsburg 



master Lorenz Helmschmied. Also the upper legs (with the exception of the flaps) and the 



shoulders are certainly made by him. Only the breastplate shows no  rivet holes that once 



held the presumed straps in place. Empty rivet holes are found at the edge of the backplate 



where the inserted plate at the nape cutout overlaps, around the shell -like extensions of the 



knees and at the upper and lower edges of the s houlders.193 Most likely they resembled in 



their ornamentation one of the different decorative strap-types found on the Vienna armours 



of the same maker (e. g. [ref_arm_3257]). 



The small holes, sometimes hold ing rivets, at the edges of the visors on the helmets 



[ref_arm_1540] [ref_arm_1548] [ref_arm_1566] [ref_arm_4258] maybe once served to fix 



ornamented copper alloy bands, maybe similar to those on [ref_arm_1495]. The lower edge 



of the helmet [ ref_arm_1756] is not turned but pierced with small holes. V ery likely they 



once held rivets for the fixation of ornamental bands. The lower legs [ ref_arm_2291] 



[ref_arm_2296] [ref_arm_2325] [ref_arm_2958] have also small rivet holes on their lower 



edges. As the edges had not be en turned, also here it is likely that copper alloy straps were 



attached, similarly to those at [ref_arm_2348].  



The lowest lame of the pelvis on breastplate [ ref_arm_3611]194 and of the backplate 



[ref_arm_3374] once was decorated by cast copper alloy bands. They might have looked 



like those on the pair of hand -protections [ ref_arm_1096] [ ref_arm_1142], as they are 



approximately contemporary and marked by the same master, Caspar Rieder of Innsbruck 



(Mühlau).
S. 131 · Sprachlich überarbeitet · Entwurf

4.3.1 Measurements

In 1474, Lower Austria’s “Zeugmeister”, Wilhelm Tenntsch or Täntschen, accompanied the young Archduke Maximilian to Augsburg to be measured by the armourer Thoma.195 This and other records show that armour for wealthy clients was made to measure. In 1488, the ten-year-old Philipp I, son of the future Emperor Maximilian I, sent a doublet and hose to his uncle, Archduke Sigismund, who wished to commission armour for him.196 The resulting suit survives in the HJRK in Vienna [ref_arm_3260] PDF, lacking only its helmet, probably of Type VII.

Without such documentation, it is difficult to establish whether an object was made for an individual. Armourers may also have offered products in standard sizes, comparable to modern small, medium and large. To investigate this question, I assembled measurements of hundreds of objects.

Comparing dimensions is an extensive undertaking. This study evaluates only three body regions: head, front torso and back. Some types could not be measured, or were represented by too few examples, so the discussion is restricted to types with sufficient comparative data. Future work should also distinguish variant groups within each type.

Redaktionelle Hinweise · 1
  • Die folgenden Schlüsse auf Maßanfertigung beruhen auf der Argumentation der Dissertation. Spannweiten allein unterscheiden Maßanfertigung, Größensortimente und unterschiedliche Formvarianten nicht eindeutig; keine neue statistische Validierung behauptet.
Originalwortlaut vergleichen
4.3.1 Measurements 



In 1474 the “Zeugmeister” of Lower Austria, Wilhelm Tenntsch (or Täntschen) accompanied 



the young Archduke Maximilian to Augsburg for having his body measured by the armourer 



Thoma.195 



This and other sources tell that armour for wealthy men was made to measure. In 1488 



Philipp I. son of the later Emperor Maximilian I. at the age of 10 had sent one of his pourpoint 



and a hose to his uncle, Archduke Sigismund, who wanted to order a suit of armour for his 



nephew.196 The delivered armour is preserved in the HJRK in Vienna [ref_arm_3260], only 



the helmet – it was probably of type-VII – is missing. 



Wherever no such documentation exists, it is not easy to answer if an extant item was made 



to measure. It is especially difficult to find final answers , as it is also possible that the 



armourers offered some of their products in different “standardized” sizes, similar to our 



modern “S, M, L etc.”. The author has assembled measurements of hundreds of objects to 



approach this question. The comparison of di mensions is an exhaustive work. For the 



moment, the measurements of only three body -regions were evaluated: heads, torso -front 



and torso-back. Some types could not be measured at all in the course of this study or in 



small numbers only. Therefore, only the types of which a wider basis for comparison exists 



were considered in the following chapter. Future research should also differentiate between 



variation-groups of the same type.
S. 131 · Sprachlich überarbeitet · Entwurf

4.3.1.1 Head

Internal width from ear to ear provides a reliable starting point for comparison. Height can also be compared when helmet skulls have similar shapes, but it does not establish whether a helmet was made to measure. Padding must also be considered: differences from an average internal size could be accommodated by adjusting the lining.

Originalwortlaut vergleichen
4.3.1.1 Head 



A very reliable measurement to be compared for a first overview is the width of the skull 



from ear to ear. The heights of some types can also be compared if the skulls of the concerned 



items are similar to each other in their shape. Nevertheless, the height does not tell if a helmet 



was made to measure. It has to be considere d that helmets were always worn with a lining 



and therefore measurement-deviations from an average might have been less important – the 



size could be adjusted by a padding of the lining.
S. 131 · Sprachlich überarbeitet · Entwurf

4.3.1.1.1 Type III

[ref_tab_dim_hea_III] Original Excel The seventy-nine helmets have different skull shapes, so heights were not compared. Mean internal width from ear to ear is approximately 18.5 cm. The 6.0 cm difference between the widest and narrowest examples indicates a broad size range, suggesting that many may have been individually fitted.

Originalwortlaut vergleichen
4.3.1.1.1 Type-III [ref_tab_dim_hea_III] 



As the compared 79 helmets had different skull -shapes, the comparison of the height -



measurements was omitted. The average width from ear to ear (inside) is about 18.5 cm. The 



max-min value of 6.0 cm shows that there is a w ide range in the helmet-sizes and therefore 



many of them were possibly customized.
S. 131–132 · Sprachlich überarbeitet · Entwurf

4.3.1.1.2 Type IV

[ref_tab_dim_hea_IV] Original Excel Internal widths across the twenty-seven helmets span only 3.0 cm, making general manufacture to individual measurements less likely. Heights, by contrast, span 8.0 cm. Most taller examples have pointed skulls. Many below-average heights belong either to hemispherical skulls [ref_arm_1542] PDF or to pointed skulls with pointed visors [ref_arm_1496] PDF [ref_arm_1519] PDF. The latter two share the impractical feature of downward-curving sight slits.

Originalwortlaut vergleichen
4.3.1.1.2 Type-IV [ref_tab_dim_hea_IV] 



The ear to ear measurements of all 27 helmets do only vary in a range of 3.0 cm difference. 



It is therefore less likely that they were generally made to measure. On the other hand, the 



height differs by 8.0 cm. Most of the higher helmets have a pointed skull. It is interesting to 



note that many items with a skull-height below the average have either a hemispherical skull 



[ref_arm_1542] or they have a pointed skull with a pointed visor attached [ ref_arm_1496]



[ref_arm_1519]. The two latter helmets have the unpractical downward-curving vision-slits 



in common.
S. 132 · Sprachlich überarbeitet · Entwurf

4.3.1.1.3 Type V

[ref_tab_dim_hea_V] Original Excel Most of the forty-five helmets were probably not made to measure: internal widths differ by only 2.5 cm. The mean width of 18.3 cm can therefore be regarded as representative. The 10.0 cm height range reflects the different groups included within Type V. A mean height of 26.6 cm is probably representative of the conventional “barbuta” form.

Originalwortlaut vergleichen
4.3.1.1.3 Type-V [ref_tab_dim_hea_V] 



Most of the 45 helmets were most likely not made to measure, as the difference between the 



widest and the shortest ear to ear measurement is only 2.5 cm. The average width of 18.3 cm 



is therefore certainly representative for this type of helmet. The heights vary by 10.0 cm 



which is d ue to the different groups to which the compared type -V helmets belong. The 



average height of 26.6 cm is probably representative for the classical “barbuta”-model.
S. 132 · Sprachlich überarbeitet · Entwurf

4.3.1.1.4 Type VII

[ref_tab_dim_hea_VII] Original Excel The eighty helmets have an internal-width range of 4.0 cm, again giving no indication that individual fitting was usual. Mean width is 18.8 cm and is regarded here as representative. Comparing heights is particularly problematic because the diagram combines several different forms.

Originalwortlaut vergleichen
4.3.1.1.4 Type-VII [ref_tab_dim_hea_VII] 



Also at these 80 helmets the max -min value of 4.0 cm of all ear to ear measurements does 



not suggest that they were usually customized. The average width of 18.8 cm is certainly 



representative. The evaluation of the heights is particul arly problematic as in the diagram 



the measurements of various models were compared.
S. 132 · Sprachlich überarbeitet · Entwurf

4.3.1.2 Torso

Width beneath the arm openings is the only torso measurement that could be compared reliably. Waist width would also be of interest, but the cut-outs on many later fifteenth-century plates prevent consistent measurement.

Originalwortlaut vergleichen
4.3.1.2 Torso 



The only measurement of torso -protections that could be reliably compared is the width 



under the arms. It would of course be interesting to compare the width of the waist as well, 



but the cutouts at the plates found at many torso -protections of the second half of the 15 th 



century do not allow a reliable measurement.
S. 132 · Sprachlich überarbeitet · Entwurf

4.3.1.2.1.1 Type II

[ref_tab_dim_tfr_II] Original Excel Across all measured examples, the 7.0 cm width range suggests possible manufacture to individual measurements. The result differs when the thirty-four very similar, plain Type II breastplates from the Vienna Zeughaus are considered separately: their range is only about 4.5 cm, making individual manufacture very unlikely.

Originalwortlaut vergleichen
4.3.1.2.1.1 Type-II [ref_tab_dim_tfr_II] 



The comparison of all measured plates implies that these breastplates might have been made 



to measure: the max-min value is 7.0 cm. The result looks different when only the 34 very 



similar simple type -II breastplates of the Vienna -Zeughaus are compared.  It is very likely 



that they were not customized as the max-min value is only about 4.5 cm.
S. 132 · Sprachlich überarbeitet · Entwurf

4.3.1.2.1.2 Type III

[ref_tab_dim_tfr_III] Original Excel The 6.5 cm range likewise suggests that many Type III breastplates were made to measure. The table combines objects of different appearance, however. Further subdivision may establish whether simpler versions were produced without individual fitting.

Originalwortlaut vergleichen
4.3.1.2.1.2 Type-III [ref_tab_dim_tfr_III] 



Also the max -min value (6.5 cm) of type -III breastplates impl ies that many of them were 



made to measure. Items different in their appearance have been compared in this table and 



therefore further differentiations might reveal closer details if the more simple versions were 



possibly not customized.
S. 132 · Sprachlich überarbeitet · Entwurf

4.3.1.2.1.3 Type IV

[ref_tab_dim_tfr_IV] Original Excel Type IV breastplates show the greatest dimensional variation, with a range of approximately 15.0 cm. This suggests that they were generally made to measure. The interpretation is supported by the comparatively large number of measured examples available for this type.

Originalwortlaut vergleichen
4.3.1.2.1.3 Type-IV [ref_tab_dim_tfr_IV] 



The dimensions of this type of breastplate vary the most. The max -min value is about 15.0 



cm which suggests that they were usually made to measure this assumption is even more  



reliable as for this type the most data of a large number of objects is available.
S. 132 · Sprachlich überarbeitet · Entwurf

4.3.1.2.2.1 Type III

[ref_tab_dim_tba_III] Original Excel Type III backplates were generally worn with Type IV breastplates, so it is unsurprising that they too appear to have been made to measure. Their width range is 8.0 cm.

Originalwortlaut vergleichen
4.3.1.2.2.1 Type-III [ref_tab_dim_tba_III] 



Backplates of type-III were usually worn together with a breastp late of type-IV . Therefore, 



it is not surprising that these backplates seem to have been also made to measure. The max-



min value is 8.0 cm.
S. 133 · Sprachlich überarbeitet · Entwurf

4.3.1.2.2.2 Type IV

[ref_tab_dim_tba_IV] Original Excel Type IV backplates were worn with Type IV breastplates. These generally formed expensive torso protection for mounted combatants and were therefore frequently made to measure. Even the small measured sample spans approximately 9.5 cm.

Dimensional comparison offers limited information unless the full range of measurements is considered. Comparing three-dimensional scans would therefore be valuable. An unidentified maker may have produced several objects with similar dimensions, potentially allowing workshop groups to be recognised.

The laser-based scanning methods considered here are unsuitable for bare iron surfaces because reflections interfere with reconstruction. Applying a powder such as chalk could theoretically reduce reflection, but conservation concerns make this undesirable: added substances could damage original objects, especially surviving organic materials. Computed tomography—three-dimensional X-ray imaging—offers a very effective but expensive alternative.

Redaktionelle Hinweise · 2
  • Die Aussagen über Grenzen laserbasierter 3D-Erfassung entsprechen dem technischen Stand der Dissertation. „The … methods considered here“ macht diesen Bezug sichtbar, ohne eine Aktualisierung oder heutige allgemeine Ungeeignetheit zu behaupten.
  • Die regelhafte Kombination von Vorder- und Rückenplattentypen beschreibt die im Original angenommene Nutzung; sie belegt keine ursprüngliche Zusammengehörigkeit konkreter Einzelobjekte.
Originalwortlaut vergleichen
4.3.1.2.2.2 Type-IV [ref_tab_dim_tba_IV] 



Type-IV backplates were worn together with a breastplate of type -IV . Usually these torso-



protections were costly armour made for horsemen and therefore they were frequently 



customized. The max-min value of the few measured items is already about 9.5 cm. 



The comparison of measurements is an exhaustive field of work and delivers only little 



information if not all dimensional aspects are compared. It would therefore be very 



interesting to compare three dimensional scans of armour parts. There is a chance that certain 



anonymous masters made several items with similar dimensions. It is therefore possible that 



groups of items coming from one workshop could be identified. The laser-based 3D scanning 



is not suitable for the imaging of bare iron -surfaces as reflect ions avoid the visual 



reconstruction of the item. It is theoretically possible to avoid problematic reflections by e. 



g. powdering the surface of the item with chalk etc. but due to conservational aspects this 



procedure is not recommendable. Any substance might harm the precious genuine examples, 



especially the organic parts. A very good, but costly alternative is the scanning by computed-



tomography (3D X-raying).
S. 133 · Sprachlich überarbeitet · Entwurf

4.3.2 Weight

One persistent misconception holds that armour was so heavy that its wearer could neither rise after a fall nor mount a horse without a crane.197 Published weights of individual objects and complete suits have done little to dispel the image of the immobile knight. Even academics repeat it, while television documentaries perpetuate misunderstandings about how armour was worn.

Late medieval armourers were specialists who carefully balanced protection against comfort. I weighed and compared numerous surviving objects to investigate this balance. Complete suits are only part of the question: individual defences used by ordinary soldiers also deserve attention. Where such objects were worn independently, the load was correspondingly smaller.

The following discussion considers types for which sufficient comparative data were available, before examining examples of complete suits. Weight alone generally cannot distinguish originals from reproductions. Apparently original objects can look very similar yet differ markedly in weight. More detailed comparison within particular groups may nevertheless reveal chronological changes or other patterns.

Redaktionelle Hinweise · 1
  • Die pauschale ursprüngliche Aussage, Teile für einfache Soldaten seien „never part of a suit“, wurde gemäß verbindlicher Terminologie durch eine bedingte Aussage zur eigenständigen Nutzung ersetzt. Aus Einzelobjekten wird weder ein Ensemble noch dessen Abwesenheit abgeleitet.
Originalwortlaut vergleichen
4.3.2 Weight  



One of the most erroneous legends about armour tells about its immense weight that ma de 



it impossible for the wearer to stand up again after having fallen to the ground or to mount 



his horse without the help of a crane. 197 Despite several publications naming the weight of 



single armour parts and in some cases also the weight of a complete su it, the image of the 



immobile “knight” is still widely spread. Such mysterious opinions are still repeated even 



by academics and “documentaries” in public media keep on amplifying a misunderstanding 



of the “knight’s” armour. 



The armourers of the late Middle Ages were specialized craftsmen that took great care of the 



balance between wearing comfort and protective aspects. The author has measured and 



compared the weights of a large number of extant objects. Not only the weight of a complete 



suit of armour should be of interest, but also armour parts for the simple soldier. These were 



never part of a suit and therefore the weight to bear was not very significant for the fighters 



anyway. 



In the following, the aspects of weight of the single armour types of which  enough 



comparable data could be collected will be discussed. Subsequently, some examples for 



weights of complete suits will be quoted.  



Weights do usually not offer the possibility to tell the genuine armour from the reproduced. 



Also items that are most l ikely genuine can look very similar while they differ widely in 



their weight. Nevertheless, future studies of items belonging to one type-group can compare 



the weights in more details and maybe reveal chronological developments etc.
S. 134 · Sprachlich überarbeitet · Entwurf

4.3.2.1 Hands

Most surviving hand defences lack their organic components and often their finger plates. Their present weights therefore do not precisely represent their original mass.

Originalwortlaut vergleichen
4.3.2.1 Hand 



It has to be attended that at most hand-protections the organic and often also the finger parts 



are missing. Therefore, the weights do not exactly represent the original mass.
S. 134 · Sprachlich überarbeitet · Entwurf

4.3.2.1.1 Type I: the “hourglass” group

[ref_tab_wei_han_I] Original Excel The diagram compares only the earliest, “hourglass” variants of Type I. All seven examples have similar dimensions and lack both organic components and finger protection, making their weights comparable. They differ only slightly from the mean of 0.28 kg, which is therefore representative of the sample. Even with finger plates and inner gloves, a complete pair would certainly have weighed no more than 1.0 kg.

Originalwortlaut vergleichen
4.3.2.1.1 Type-I “hourglass” [ref_tab_wei_han_I] 



Only the earliest group of type-I hand-protections, the “hour-glass” variations are compared 



in this diagram. As all these hand-protections have similar dimensions, all of them lack their 



organic parts and the fingers, the weights are we ll comparable. The average weight of 0.28 



kg is representative, as all 7 compared items do only slightly deviate in their weight from 



this mean. This is of course a very light armour part, even together with the finger-parts and 



the lining a pair of hand-protections of this group did certainly not weight more than 1.0 kg.
S. 134 · Sprachlich überarbeitet · Entwurf

4.3.2.1.2 Type II

[ref_tab_wei_han_II] Original Excel Type II hand defences are somewhat heavier than the early Type I examples. The seven measured objects average approximately 0.54 kg. A complete pair may therefore have weighed about 1.4 kg.

Originalwortlaut vergleichen
4.3.2.1.2 Type-II [ref_tab_wei_han_II] 



Type-II hand-protections are a little bit heavier than the early type -I examples. The average 



weight of 7 examples is about 0.54 kg. This means that a complete pair might have weighed 



maybe 1.4 kg approximately.
S. 134 · Sprachlich überarbeitet · Entwurf

4.3.2.1.3 Type III

[ref_tab_wei_han_III] Original Excel Despite its many articulated elements and coverage of the hand and part of the forearm, Type III remains light. The thirty-three examples average 0.45 kg, suggesting that a complete pair may have weighed no more than 1.4 kg.

Redaktionelle Hinweise · 1
  • Der Originalvergleich „very low, compared to the types mentioned above“ trifft auf den höheren Mittelwert von Typ II zu, nicht auf den niedrigeren Wert der frühen Typ-I-Gruppe. Die Zahlen bleiben unverändert; der widersprüchliche pauschale Vergleich wurde weggelassen.
Originalwortlaut vergleichen
4.3.2.1.3 Type-III [ref_tab_wei_han_III] 



Even though this type of hand-protection usually consists of many segments and even though 



it flexibly covers all the hand and parts of the lower arm, the average weight of all 33 items 



is very low, compared to the types mentioned above. As the average weight is 0.45 kg a 



complete pair might have weighed not more than 1.4 kg.
S. 134 · Sprachlich überarbeitet · Entwurf

4.3.2.1.4 Type IV

[ref_tab_wei_han_IV] Original Excel Only six Type IV hand defences could be compared. Their mean of 0.42 kg likewise indicates a complete pair weighing no more than 1.4 kg, with flexibility comparable to Type III.

Originalwortlaut vergleichen
4.3.2.1.4 Type-IV [ref_tab_wei_han_IV] 



Only six hand-protections of type-IV could be compared, but also here the average of 0.42 



kg shows that a pair was not heavier than 1.4 kg while the flexibility was as comfortable as 



of type-III hand-protections.
S. 134 · Sprachlich überarbeitet · Entwurf

4.3.2.2.1 Type IV

[ref_tab_wei_hea_IV] Original Excel Mean weight is approximately 2.33 kg, with a difference of about 2.26 kg between the heaviest and lightest examples. The range is therefore broad, although many objects lie close to the mean. These helmets often originally carried a ring-armour collar, which would have added substantial weight.

Originalwortlaut vergleichen
4.3.2.2.1 Type-IV [ref_tab_wei_hea_IV] 



The average weight of helmets of type-IV is about 2.33 kg, but the max-min value is already 



about 2.26 kg high. Therefore, it is clear that these helmets have a wide weight -range. 



Nevertheless, the weight of many examples does not deviate very much from the average. It 



has to be considered that this type of helmet frequently once had a ring -armour collar of 



significant additional weight attached.
S. 134 · Sprachlich überarbeitet · Entwurf

4.3.2.2.2 Type V

[ref_tab_wei_hea_V] Original Excel The forty-six examples average about 2.4 kg. This is regarded as representative of the conventional “barbuta” form, although many examples are slightly heavier and other Type V variants tend to be lighter.

Originalwortlaut vergleichen
4.3.2.2.2 Type-V [ref_tab_wei_hea_V] 



The average weig ht of the 46 compared examples is about 2.4 kg. This is certainly 



representative for the classical “barbuta”. Many of them were actually a bit heavier while 



other type-V models seem to be rather lighter.
S. 134 · Sprachlich überarbeitet · Entwurf

4.3.2.2.3 Type VI

[ref_tab_wei_hea_VI] Original Excel The original weight of Type VI helmets was considerably greater than the measured mean of 3.52 kg, because they also carried a ring-armour collar.

Originalwortlaut vergleichen
4.3.2.2.3 Type-VI [ref_tab_wei_hea_VI] 



The weight of type -VI helmets was originally much more than the average of 3.52 kg as 



these helmets once had a ring-armour collar attached.
S. 135 · Sprachlich überarbeitet · Entwurf

4.3.2.2.4 Type VII

[ref_tab_wei_hea_VII] Original Excel The mean of 2.54 kg is not yet representative and serves only as a rough guide. The 3.63 kg range reflects considerable variation among the forms combined in the table; several examples, for instance, lack visors. Further conclusions require subdivision into these groups and larger samples within each.

Originalwortlaut vergleichen
4.3.2.2.4 Type-VII [ref_tab_wei_hea_VII] 



The average weight of 2.54 kg of this type of helmet is not representative yet and provides 



only a slight orientation. The max-min value of 3.63 kg shows that the single items differ in 



their weight widely from each other. This is due to the many different groups comprised in 



this table. Several items have e. g. no visor. For further conclusions, the data needs to be split 



into the single groups in further studies and more items of each group need to be compared.
S. 135 · Sprachlich überarbeitet · Entwurf

4.3.2.2.5 Type VIII

[ref_tab_wei_hea_VIII] Original Excel Type VIII includes numerous forms that could themselves constitute separate types. Its mean of 5.82 kg is therefore not representative; the range is about 2.92 kg. Future studies must distinguish the individual groups.

Originalwortlaut vergleichen
4.3.2.2.5 Type-VIII [ref_tab_wei_hea_VIII] 



This type comprises many different helmet models that could even be ascribed to types of 



their own. Therefore, also here the average weight of 5.82 kg cannot be r epresentative, the 



max-min value is about 2.92 kg. Future studies need to differentiate the weight of different 



groups.
S. 135 · Sprachlich überarbeitet · Entwurf

4.3.2.3.1 Type I

[ref_tab_wei_nec_I] Original Excel Type I neck protection is rarer than Type II, so little data were available. The six incomplete examples average 0.82 kg, a value regarded here as representative. A complete example may have weighed about 1.0 kg.

Originalwortlaut vergleichen
4.3.2.3.1 Type-I [ref_tab_wei_nec_I] 



These neck-protections are more rar ely than those of type -II and therefore also only little 



data was at hand. The average weight of 0.82 kg for 6 not complete examples is certainly 



representative. A complete example might have weighed about 1.0 kg.
S. 135 · Sprachlich überarbeitet · Entwurf

4.3.2.3.2 Type II

[ref_tab_wei_nec_II] Original Excel Type II averages 0.75 kg, broadly comparable to Type I. By contrast, [ref_arm_3034] PDF weighs 1.75 kg, approximately two and a half times the mean. It was very probably intended solely for tournament use. Three vertically arranged screw holes for attachment to the breastplate support this interpretation, since such fastenings are characteristic of tournament armour.

Originalwortlaut vergleichen
4.3.2.3.2 Type-II [ref_tab_wei_nec_II] 



The neck defenses of type-II weigh in average 0.75 kg and are therefore more or less of the 



same weight as those of type-I. For example the item [ref_arm_3034] (1.75 kg) weighs about 



2.5 times the average. It is very likely that this example was meant for tournament only, as 



also the 3 vertical holes suggest. These holes served for the fastening of the neck-protection 



to the breastplate via screws, a feature typical for tournament armour.
S. 135 · Sprachlich überarbeitet · Entwurf

4.3.2.4.1 Front

Future studies should subdivide the breastplate data further, for example by comparing plain examples with those bearing lance-rest attachment holes.

Originalwortlaut vergleichen
4.3.2.4.1 Front 



For all breastplates in future studies it would be interesting to further differentiate the data, 



e. g. to compare simple breastplates to those with holes for lance-rests.
S. 135 · Sprachlich überarbeitet · Entwurf

4.3.2.4.1.1 Type II

[ref_tab_wei_tfr_II] Original Excel The sixty Type II breastplates average 1.99 kg. The 1.86 kg range nevertheless indicates substantial variation.

Originalwortlaut vergleichen
4.3.2.4.1.1 Type-II [ref_tab_wei_tfr_II] 



The 60 type-II breastplates weigh in average 1.99 kg. The max-min value of 1.86 kg shows 



that there is nevertheless a wide range in the weights.
S. 135 · Sprachlich überarbeitet · Entwurf

4.3.2.4.1.2 Type III

[ref_tab_wei_tfr_III] Original Excel The nine Type III breastplates average 2.80 kg and appear generally heavier than Type II, probably because of their construction and overlapping plates. The 5.1 kg example [ref_arm_3623] PDF, however, raises the mean substantially.

Originalwortlaut vergleichen
4.3.2.4.1.2 Type-III [ref_tab_wei_tfr_III] 



Probably due to their construction and the overlapping edges the 9 breastplates of type -III 



with an average weight of 2.80 kg seem to be generally heavier than those of type -II, but it 



is the item [ref_arm_3623] with 5.1 kg that lifts the average immensely.
S. 135 · Sprachlich überarbeitet · Entwurf

4.3.2.4.1.3 Type IV

[ref_tab_wei_tfr_IV] Original Excel A range of 4.86 kg shows that the mean of 3.05 kg is not representative of all forty-nine examples. The heaviest is Italian and weighs approximately 6.40 kg [ref_arm_3649] PDF.

Originalwortlaut vergleichen
4.3.2.4.1.3 Type-IV [ref_tab_wei_tfr_IV] 



The max-min value of 4.86 kg shows that the average weight of 3.05 kg is not representative 



for all 49 items. The heaviest breastplate is of Italian make and weighs about 6.40 kg 



[ref_arm_3649].
S. 136 · Sprachlich überarbeitet · Entwurf

4.3.2.4.2.1 Type III

[ref_tab_wei_tba_III] Original Excel The twenty-five Type III backplates average 2.76 kg. This is regarded as representative because the range, 1.56 kg, is relatively small.

Originalwortlaut vergleichen
4.3.2.4.2.1 Type-III [ref_tab_wei_tba_III] 



The average weight of 2.76 kg is representative for 25 backplates of type-III as the max-min 



value is at the rather low rate of 1.56 kg.
S. 136 · Sprachlich überarbeitet · Entwurf

4.3.2.4.3 Limbs

Individual limb plates often cannot be weighed separately because they are permanently joined to other elements. The following discussion therefore considers a few surviving assemblies corresponding to the systems described earlier.198

Originalwortlaut vergleichen
4.3.2.4.3 Limbs 



The weights of the single armour parts f or the limbs can often not be tested as they are 



permanently connected to other arm defenses. Therefore, only some examples of extant 



items connected in one of the systems described above198 will be introduced.
S. 136 · Sprachlich überarbeitet · Entwurf

4.3.2.4.3.1 Arms

[ref_tab_wei_arm_ge] Original Excel [ref_tab_wei_arm_it] Original Excel Five examples of [sys_asII_auI_aeII_alIII_ge] weigh between 1.48 and 2.03 kg per arm. The Italian system [sys_asII_auII_aeII_alIII_it] is generally heavier: six examples range from 2.73 to 4.10 kg per arm.

Originalwortlaut vergleichen
4.3.2.4.3.1 Arm [ref_tab_wei_arm_ge] [ref_tab_wei_arm_it] 



Five examples of the system [sys_asII_auI_aeII_alIII_ge] weigh between 1.48 a nd 2.03 kg 



(one arm). The Italian system [sys_asII_auII_aeII_alIII_it] is usually heavier: Six examples 



weigh between 2.73 and 4.10 kg.
S. 136 · Sprachlich überarbeitet · Entwurf

4.3.2.4.3.2 Legs

[ref_tab_wei_leg] Original Excel The five measured examples of [sys_luII_lkII_llIII] weigh between 1.97 and 2.49 kg per leg.

Originalwortlaut vergleichen
4.3.2.4.3.2 Leg [ref_tab_wei_leg] 



The five measured leg -systems [sys_luII_lkII_llIII] weigh between 1.97 and 2.49 kg (one 



leg).
S. 136 · Sprachlich überarbeitet · Entwurf

4.3.2.4.4 Complete suits

[ref_tab_wei_sui] Original Excel Establishing a complete suit’s weight is difficult because no complete ensemble survives in its original composition. A largely complete example, [ref_arm_4143] PDF, may even have been worn in its present combination, although its marks identify different makers. It weighs 23.37 kg. Foot protection is absent, but may never have formed part of the ensemble.

The composite suit [ref_arm_4117] PDF, whose components all formerly belonged to Churburg, may likewise have been worn in its present combination. Some elements, including thigh protection attached to the torso, are missing, so its measured 26.88 kg may be slightly below its original weight. These two examples support the conclusion that a suit generally weighed less than 30.00 kg.

The total combat load would have been somewhat greater because ring-armour shirts or inserts accompanied the plates, and missing organic components also contributed weight. The wearers were nevertheless highly trained combatants, comparable to modern athletes, who devoted considerable time to running and riding in full armour.

Modern soldiers likewise march and run with backpacks of 20 kg or more, helmets of 2–3 kg, sometimes ballistic protection, and weapons with ammunition. Plate armour, by contrast, distributed its weight across the body. For a knight, being unable to mount a horse in armour without assistance would certainly have been embarrassing.

Redaktionelle Hinweise · 2
  • Die Aussage zur üblichen Obergrenze unter 30 kg bleibt der ursprüngliche Schluss aus den beiden genannten Ensembles; keine neue repräsentative Stichprobe behauptet.
  • Die Originalgliederung ordnet Gliedmaßen und vollständige Ensembles unter 4.3.2.4 „Torso“ ein. Diese Nummerierung bleibt für stabile Querverweise erhalten.
Originalwortlaut vergleichen
4.3.2.4.4 Suit [ref_tab_wei_sui] 



It is difficult to quote the total weight of a suit as no complete ensemble exists in its original 



composition. A mostly complete example – which was probably even worn in the current 



constellation – is the suit [ ref_arm_4143]. According to the marks, the single parts were 



made by different masters. The total weight is 23.37 kg, but it has to be considered that the 



shoe-protections are missing (or they never existed). Another good example is the composite 



suit [ref_arm_4117] that also might have been worn i n the current constellation (all parts 



formerly Churburg armoury). Some parts, like the torso upper-leg defenses, are missing and 



therefore the weight of 26.88 kg might have been a little bit higher. These two total weights 



show that the weight of a suit o f armour was usually below 30.00 kg. The total weight to 



bear in battle was certainly slightly higher, as also ring-armour shirts or segments were worn 



together with the plate armour. The missing organic armour-parts had an additional weight. 



Nevertheless, the men inside these suits were all highly trained fighting specialists, similar 



to modern athletes. They spent a lot of their lifetime on running and riding with full armour. 



Today’s soldiers do also usually not collapse when they have to march or to run with a back-



pack of 20 kg or more, a helmet of 2 -3 kg, possibly a bullet -proof vest and a heavy gun 



together with some cartridges. Unlike such modern fighting equipment, the weight of plate 



armour was spread all over the wearer’s body. There is no doubt t hat it would have been a 



very embarrassing moment for a knight if he appeared to be too weak to mount his horse in 



full armour without support.
S. 136–137 · Sprachlich überarbeitet · Entwurf

4.3.3 Plate thickness

Plate thickness is another substantial field requiring closer examination. Claude Blair wrote:

“Considerable care was taken in forging a fine-quality armour over such



details as the thickness of the various parts. It will usually be found that,



for obvious reasons, the parts at the front are thicker than those at the



back while the helmet-skull is worked so that it is thicker in the more



vulnerable places.”
Blair (1972), p. 189. 199

The widely accepted view that exposed areas were deliberately made thicker had never been tested comparatively. If Blair measured a series of objects, he published no record of it. Nor had a systematic method been developed for measuring different armour types. For this study, I measured many objects at repeatable locations, allowing a point on one object to be compared with the corresponding point on another. The data were then evaluated to investigate manufacture. A short film illustrates the procedure [ref_vid_meas]. The lowest local reading was recorded at each measurement location.200

The objects fall into two groups. The first comprises helmets and torso protection, the only categories repeatedly showing very substantial variation in thickness. Measurement locations were precisely defined. Means for individual objects and whole types were calculated and presented in two- and three-dimensional diagrams. Since these objects survive in the greatest numbers, they also provided the largest datasets.

Other categories, including limb, hand and attached thigh protection, generally have a more even thickness. A few points were measured at random on each object, recording the minimum, maximum, range and mean. These values were also evaluated across each type and plotted in two dimensions. Since these objects are comparatively rare, some assessments rely on only two or three examples. Future work should distinguish date, place of manufacture and quality. The conclusions are provisional and require testing through further measurements.

The diagrams may help identify objects requiring closer examination. An exceptionally small thickness range within one object may suggest modern rolled sheet and warrant investigation of authenticity. Three-dimensional plots provide a useful view of variation across a type. The differing section profiles are very likely to reflect forming techniques rather than a deliberate intention to reinforce exposed areas.

Redaktionelle Hinweise · 1
  • Gleichmäßige Dicke wird als Anlass für weitere Prüfung behandelt, nicht als alleiniger Nachweis einer Reproduktion. Die Erklärung durch Herstellungsverfahren bleibt eine Hypothese der Dissertation.
Originalwortlaut vergleichen
4.3.3 Plate-thickness 



The topic of plate -thicknesses is another vast field of interest that demands a closer look. 



Claude Blair said that:



“Considerable care was taken in forging a fine-quality armour over such 



details as the thickness of the various parts. It will usually be found that, 



for obvious reasons, the parts at the front are thicker than those at the 



back while the helmet-skull is worked so that it is thicker in the more 



vulnerable places.”199  



This general held belief that armour was purposely designed thicker at the exposed areas 



was never tested in a comparative study. If Claude Blair had measured a series of items, he 



never published any document on that. No system for the measuring of plate-thicknesses of 



the different armour parts had ever been developed. The author of this paper has measured a 



large number of objects of all types in a repeatable manner, so a single spot measured on one 



item can easily be compared to the same spot at a similar object. The revealed data was 



evaluated to draw general conclusions on the making of armour. To get an impression on 



how the measuring was carried out, the author has made a short movie [ref_vid_meas]. The 



lowest locally measured value was finally documented.200  



The measured armour types need to be divided into two groups. The first one comprises the 



torso-protections and the helmets. It was found that only examples of these types repeatedly 



showed immensely varying plate -thicknesses. The location where the plates  had to be 



measured needed to be clearly defined. The average values of the single and of all items of 



one type were evaluated and visualized in 2 -, respectively 3-dimensional diagrams. As the 



items of this block are those extant in the largest numbers, it is also this block that delivered 



the most data. For all other objects, such as limb -protections, hands, torso -upper leg -



protections etc. the plate -thickness is usually more or less equally spread over the surface. 



Here only few spots were randomly measur ed, the maximum, the minimum, the difference 



(max-min) and an average value of one item was noted and also evaluated for all measured 



items of one type. The data is displayed in two dimensional diagrams. As the single parts of 



this block are rather rare– compared to the numbers of extant helmets and torso-protections 



– in some cases the measurements of only two or three objects had to serve as the basis for 



the evaluations. Future examinations should differ between the date, the production -place 



and the quality of the single items. The conclusions presented in this study are not final and 



further measuring is necessary to test the reliability of the results.  



The quoted diagrams might help to identify problematic items. If the max -min value of all 



measures of one item is demonstratively low, a closer examination on the object in concern 



of its authenticity is recommendable. Equal plate thickness might mean that the plate was 



rolled by a modern technique. A good visualization of the varying plate -thickness of all 



examples of one type is provided by 3 -dimensional diagrams. It is very likely that the 



different section-profiles found at different types are rather the result of the used embossing-



technique than the idea of purposely reinforcing certain exposed areas.
S. 138 · Sprachlich überarbeitet · Entwurf

4.3.3.1.1 Head

Helmets were measured at four evenly spaced points along each of three sections: front, centre and rear.201 The three-dimensional diagrams represent a simplified plate blank viewed from the front left of the forehead.

Originalwortlaut vergleichen
4.3.3.1.1 Head201 



The helmets were measured at four equally spread spots along a frontal, a central and a rear 



section. The quoted 3 -D diagrams show in a simplified way the blank of the helmet -plate, 



looking from the frontal left side of the forehead.
S. 138 · Sprachlich überarbeitet · Entwurf

4.3.3.1.1.1 Type I

[ref_tab_thi_hea_I] Original Excel Comparable measurements were available for only three Type I helmets. Their overall mean thickness is about 1 mm. The mean variation is approximately 0.8 mm, with a measured minimum of 0.7 mm and maximum of 1.7 mm. Hemispherical Type I helmets were therefore probably made from relatively thin plate and were correspondingly light, consistent with their proposed use beneath ring armour or a hat.

In this small sample, the front and rear sections appear generally thicker than the centre. Since the centre is an expected impact area, this pattern may reflect the forming process rather than planned reinforcement. The helmets were probably worked chiefly from the outside.

Redaktionelle Hinweise · 1
  • Die mittlere Spannweite von 0,8 mm und die genannten Extremwerte 0,7/1,7 mm bleiben getrennte Angaben des Originals. Die mittlere Spannweite ist nicht mit der Differenz sämtlicher Extremwerte gleichzusetzen.
Originalwortlaut vergleichen
4.3.3.1.1.1 Type-I [ref_tab_thi_hea_I] 



Comparable data of only three helmets of type -I could be collected. Nevertheless, when 



looking at the diagrams it becomes clear that the average plate-thickness of all tested helmets 



is about 1 mm. As the average variation is only about 0.8 mm at a measured minimum of 0.7 



mm and a maximum of 1.7 mm, it is reasonable to assume that hemispheric-shaped helmets 



of type-I were usually made of thinner plate and therefore rather light. This matches with the 



assumption that they had often been worn underneath a ring-armour cape or a hat. According 



to the few measured items, it seems as if the frontal and the rear section are generally thicker 



than the central section. As these helmets are rather thin at the center – the area where a blow 



is expected to hit the skull – it is possible that the thicker parts rather result of the embossing 



technique. Probably the helmets were worked merely from the exterior.
S. 138 · Sprachlich überarbeitet · Entwurf

4.3.3.1.1.2 Type II

[ref_tab_thi_hea_II] Original Excel The rarity and often poor condition of “great helms” allowed only two examples to be measured. Neither is an archaeological find, and their use in fourteenth-century combat is uncertain. Mean plate thickness is about 1.5 mm, with relatively little variation within each segment.

Originalwortlaut vergleichen
4.3.3.1.1.2 Type-II [ref_tab_thi_hea_II] 



The rarity of helmets of the “great-helm” group and the bad condition of many items allowed 



for the measuring of only two examples. Both items are no archaeological finds and it is not 



sure if they were ever used as combat helmets in the 14th century. The average plate-thickness 



is about 1.5 mm. The single segments show a rather constant thickness.
S. 138 · Sprachlich überarbeitet · Entwurf

4.3.3.1.1.3 Type III

[ref_tab_thi_hea_III] Original Excel Local measurements clearly show that these helmets are often thicker towards the crown and thinner at the brim or lower portions. This supports manufacture from a smaller, thick blank whose edges were first forged out to enlarge it and reduce weight in less exposed areas. Subsequent work chiefly from the inside would have left the least-worked central area close to its initial thickness.

Originalwortlaut vergleichen
4.3.3.1.1.3 Type-III [ref_tab_thi_hea_III] 



The local measurements show clearly that these helmets were frequently thicker towards the 



center of the skull. The brim or the lower areas were thinner. This supports the idea that the 



armourer started from a smaller, thick plate -sheet. He first forged the edges of the plate 



thinner to reveal a larger plate and to reduce the weight at the less exposed areas. He then 



merely worked from the interior, which left the least worked areas in the center nearly at the 



starting-thickness.
S. 138 · Sprachlich überarbeitet · Entwurf

4.3.3.1.1.4 Type IV

[ref_tab_thi_hea_IV] Original Excel The calculated mean thickness of 1.9 mm is regarded as representative. These helmets are generally thinner at the cheeks and thicker towards the skull’s apex, particularly at the rear. Forming probably resembled the proposed Type III process, chiefly working from inside. Only the point needed external working, gathering the metal and increasing its thickness there.

Originalwortlaut vergleichen
4.3.3.1.1.4 Type-IV [ref_tab_thi_hea_IV] 



The calculated average plate-thickness of 1.9 mm is certainly representative. These helmets 



were usually thinner at the cheeks and thicker towards the point of th e skull, particularly at 



the rear. The embossing of the skull was probably similar to the making of helmets of type-



III – merely worked from the interior. Only the point then needed to be worked from outside, 



which resulted in an increasing thickness, as the material was bulged here.
S. 138–139 · Sprachlich überarbeitet · Entwurf

4.3.3.1.1.5 Type V

[ref_tab_thi_hea_V] Original Excel Type V helmets are frequently thicker towards the crest, suggesting the same manufacturing sequence as Type III. The crest was probably deliberately left thick: measurements reach 4.8 mm, compared with approximately 1 mm in lower areas. The diagram clearly shows that the forehead was not made thicker than other areas around the crest.

Originalwortlaut vergleichen
4.3.3.1.1.5 Type-V [ref_tab_thi_hea_V] 



Helmets of type -V are clearly frequently thicker towards the crest. This suggests their 



making by the same techniques like helmets of type-III. It is likely that the crest area was 



purposely left thicker, as frequently enormous dimensions of up to 4.8 mm were measured,



while at the lower areas the thickness could be at about 1 mm only. The diagram shows 



clearly that the forehead was not worked thicker than the other areas around the crest.
S. 139 · Sprachlich überarbeitet · Entwurf

4.3.3.1.1.6 Type VI

[ref_tab_thi_hea_VI] Original Excel Construction makes Type VI difficult to measure. A second plate generally reinforces the forehead, often preventing measurement of the underlying skull there.202 These helmets also appear to combine two kinds of stock: comparatively thin, ready-made sheet cut and shaped into cheek plates, and a thick forged skull.

Originalwortlaut vergleichen
4.3.3.1.1.6 Type-VI [ref_tab_thi_hea_VI] 



Due to their construction it was difficult to measure helmets of type -VI. The forehead is 



usually reinforced with a second plate and therefore the plate -thickness could often not be 



measured in this area. 202 Furthermore, these helmets seem to consist of a mix of two kinds 



of plates. The cheek -plates were cut and embossed from readymade plate -sheet, thinner in 



comparison to the forged, thick skull.
S. 139 · Sprachlich überarbeitet · Entwurf

4.3.3.1.1.7 Type VII

[ref_tab_thi_hea_VII] Original Excel Type VII helmets have more uniform thickness on average than Types III, IV and V, and are even thinner towards the central crest. This may indicate a different forming process. The diagram suggests internal working followed by a second operation: narrowed areas could have been formed by gathering the metal of a bowl, or wider areas above the ears could have been expanded from inside. The latter is more likely because the diagram shows thinner metal there.

This group includes helmets of widely differing shapes and dates, so conclusions based on its average measurements remain tentative. Subdivision into related forms may reveal different patterns.

Originalwortlaut vergleichen
4.3.3.1.1.7 Type-VII [ref_tab_thi_hea_VII] 



Helmets of type-VII are in average of rather equal plate -thickness compared to helmets of 



type-III, -IV and -V . Type-VII helmets are even thinner towards the central crest. This might 



suggest that they were made in a different technique. The diagram suggests the working of 



the skulls from the interior with a second step: The tapered parts could either have been made 



by bulging a bowl at the narrow areas or by embossing the wider areas above the ears from 



the interior (see also below). The latter possibility is more likely as the diagram shows the 



thinner areas here. In this type -group the author has comprised a lot of helmets different in 



shape and production time and therefore the conclusions on the average measureme nts are 



not meant to be set in stone. A further differentiation of the question with a focus on the type-



families might reveal different aspects.
S. 139 · Sprachlich überarbeitet · Entwurf

4.3.3.1.2 Torso

Torso plates were measured from left to right along four sections: pelvis, abdomen, chest and shoulder points. The three-dimensional diagrams show a simplified blank from the wearer’s perspective.

Originalwortlaut vergleichen
4.3.3.1.2 Torso 



The torso-plates were measured along four sections from the left side to the right: at the 



pelvis, at the abdomen, at the thorax and at the shoulder -points. The quoted 3 -D diagrams 



allow a look onto the simplified blank from the wearer’s perspective.
S. 139 · Sprachlich überarbeitet · Entwurf

4.3.3.1.2.1 Front

The following comparisons concern Types II–IV; insufficient data were available for Type I.203

Originalwortlaut vergleichen
4.3.3.1.2.1 Front203
S. 139 · Sprachlich überarbeitet · Entwurf

4.3.3.1.2.1.1 Type II

[ref_tab_thi_tfr_II] Original Excel A mean thickness of 1.5 mm and a mean maximum of 1.9 mm indicate relatively thin plates.204 Many similar infantry breastplates in the WM, probably from the early sixteenth century, are particularly thin, with individual means generally between 1.1 and 1.7 mm.

The combined diagram shows a slight increase towards the centre, becoming more pronounced towards the lower abdomen. This suggests blanks smaller than the finished product, with their edges subsequently forged out thinner. Besides reducing weight in less exposed areas, this would facilitate turning the edges. On many WM breastplates, the edges beneath the arms were never finally trimmed or ground. Their burrs clearly indicate that forging established the final dimensions.

Originalwortlaut vergleichen
4.3.3.1.2.1.1 Type-II204 [ref_tab_thi_tfr_II] 



The average plate -thickness of 1.5 mm, the average maximum of 1.9 mm show that these 



plates were usually not very thick. Especially the many similar foot-soldier’s breastplates of 



the WM, probably made in the early 16th century, are frequently thin, most of them in average 



between 1.1 to 1.7 mm. The average diagram of all items shows that the plates were slightly 



thicker towards the center, increasingly towards the lower abdomen. This suggests that the 



plates were cut in smaller dimensions than the readymade product and they were 



subsequently forged thinner towards the edges. This does not only reduce weight at the less 



exposed areas but it also eases the turning of the edges. The edges under the arms at the WM 



breastplates were frequently not finally cut or ground. Their burred appearance clearly shows 



that the final dimensions were finished by forging.
S. 140 · Sprachlich überarbeitet · Entwurf

4.3.3.1.2.1.2 Type III

[ref_tab_thi_tfr_III] Original Excel The three-dimensional diagram shows increasing thickness towards the centre of the chest plate.205 The abdominal plate also thickens centrally and is thicker than the lower chest section. These plates were therefore likewise cut as smaller blanks and forged thinner towards the edges. Pelvic lames do not become substantially thinner towards the sides and were probably cut from larger sheet.

Originalwortlaut vergleichen
4.3.3.1.2.1.2 Type-III205 [ref_tab_thi_tfr_III] 



It is interesting to note that the 3-D diagram shows an increase of the plate-thickness towards 



the center of the thorax -plate. Also the abdomen -plate is thicker towards the center and 



thicker than the lower thorax -section. The single plates therefore were also cut smaller and 



subsequently forged thinner towards the edges. The pelvis-lames are not significantly thinner 



towards the sides of the body and were probably cut from a large plate.
S. 140 · Sprachlich überarbeitet · Entwurf

4.3.3.1.2.1.3 Type IV

[ref_tab_thi_tfr_IV] Original Excel Pelvic lames are generally thinner than the upper plates and only slightly thicker at their centres. As in other breastplate types, the upper plates thicken towards the centre. The chest and abdominal plates have almost the same mean thickness; both were generally forged to their final dimensions from smaller blanks.

Originalwortlaut vergleichen
4.3.3.1.2.1.3 Type-IV [ref_tab_thi_tfr_IV] 



The pelvis-lames are frequently thinner than the other parts, but only slightly thicker at the 



center. As shown in the diagrams of the other breastplate -types, also here the upper plates 



are thicker towards the center. The average plate -thickness of the abdomen and the thorax -



plate is nearly the same. They both were usually forged into the right dimensions from a 



smaller plate.
S. 140 · Sprachlich überarbeitet · Entwurf

4.3.3.1.2.1.4 Attached thigh protection

[ref_tab_thi_tfr_leg] Original Excel Thigh defences attached below the pelvic lames were generally cut from sheet, since they do not become thinner towards the edges. Their mean thickness of 1.2 mm is regarded as representative: the mean range within individual objects is only 0.5 mm.

Originalwortlaut vergleichen
4.3.3.1.2.1.4 Upper-leg [ref_tab_thi_tfr_leg] 



The upper-leg-protections adjacent to the pelvis -lames of breastplates are usually cut from 



plate sheet, as they do not show a decrease in the plate -thickness towards the edges. The 



average thickness of 1.2 mm is certainly representative, as the average max-min value of all 



measured objects is 0.5 mm only.
S. 140 · Sprachlich überarbeitet · Entwurf

4.3.3.1.2.2 Back

Insufficient data were available for Types I and II, which were therefore excluded.206

Originalwortlaut vergleichen
4.3.3.1.2.2 Torso back206
S. 140 · Sprachlich überarbeitet · Entwurf

4.3.3.1.2.2.1 Type III

[ref_tab_thi_tba_III] Original Excel The overall mean of 1.4 mm shows that Type III backplates are generally thinner than the Type IV breastplates with which they are commonly paired. The upper plates thicken towards the centre, suggesting smaller blanks forged thinner around their edges. The chest-level plate is often thinner than the abdominal plate. Pelvic lames are thinner on average than the upper plates and show no marked central thickening, suggesting that they were cut from sheet and only lightly forged, if at all.

Originalwortlaut vergleichen
4.3.3.1.2.2.1 Type-III [ref_tab_thi_tba_III] 



The average plate-thickness of 1.4 mm (all objects) shows that the backplates of type-III are 



usually thinner than the breastplates of type -IV , with which they are commonly combined. 



The quoted 3-D diagram illustrates that the upper plates are thicker towards the center, which 



suggests that they were probably cut from the sheet with smaller dimensions and forged 



thinner towards the edges. The thorax -plate is often thinner than the abdomen -plate. The 



pelvis-lames are in average thinner than the upper plates and as they are not significantly 



thicker towards the center, it is possible that they were cut from the plate-sheet and possibly 



only slightly forged.
S. 140 · Sprachlich überarbeitet · Entwurf

4.3.3.1.2.2.2 Type IV

[ref_tab_thi_tba_IV] Here too, the uniform thickness of the pelvic lames suggests ready-made sheet. The abdominal plate is much thicker than the chest-level plate, but both were forged thinner towards their edges.

Originalwortlaut vergleichen
4.3.3.1.2.2.2 Type-IV [ref_tab_thi_tba_IV] 



Also here the equal thickness of the pelvis -lames suggests that they were cut from a 



readymade plate-sheet. The abdomen -plate is much thicker than the thorax -plate, but both 



were forged thinner towards the edges.
S. 140–141 · Sprachlich überarbeitet · Entwurf

4.3.3.2.1 Arms

[ref_tab_thi_arm] Original Excel Mean thickness is often slightly greater in armpit plates (1.4 mm), elbow reinforcements (1.3 mm) and shoulder reinforcements (1.2 mm) than in other arm defences (0.9–1.2 mm). The generally small ranges indicate that particular areas were not deliberately forged thinner. These plates were therefore most probably cut from sheet close to their final dimensions.

Originalwortlaut vergleichen
4.3.3.2.1 Arm [ref_tab_thi_arm] 



The diagrams show that the average plate -thickness of armpits (1.4 mm), elbow reinforces 



(1.3 mm) and shoulder reinforces (1.2 mm) is often a bit higher than the thickness of the 



remaining arm-protections (0.9 – 1.2 mm). The usually low max-min value indicates that the



plates for the arms were not purposely forged thinner at certain areas and were therefore 



most likely cut from the sheet into more or less the final dimensions.
S. 141 · Sprachlich überarbeitet · Entwurf

4.3.3.2.2 Legs

[ref_tab_thi_leg] Original Excel As with arm protection, the thickness ranges indicate that leg plates were not forged thinner towards their edges. They were therefore also cut from prepared sheet. Knee plates (1.0 mm) and thigh plates (1.1 mm) were slightly thicker than lower-leg plates (0.9 mm) and foot plates (0.7 mm).

Originalwortlaut vergleichen
4.3.3.2.2 Leg [ref_tab_thi_leg] 



Similarly to the arm-protections also the max-min values of the single leg-armour types were 



never forged thinner towards the edges. Therefore, also these parts were made from ready -



cut plates. The knees (1.0 mm) and the upper legs (1.1 mm) were slightly thicker than the 



lower legs (0.9 mm) and the feet (0.7).
S. 141 · Sprachlich überarbeitet · Entwurf

4.3.3.2.3 Hands

[ref_tab_thi_han] Original Excel Hand-protection plates show no significant thinning towards their edges, suggesting that they were cut from larger sheet close to their final dimensions. Mean ranges are small for Types II, III and IV, at 0.4–0.5 mm, and slightly greater for Type I, at 0.7 mm. Types III and IV average 0.8–0.9 mm in thickness, less than the 1.2 mm average of the generally earlier Types I and II.

Originalwortlaut vergleichen
4.3.3.2.3 Hand [ref_tab_thi_han] 



The plates of all hand -protections are never signi ficantly thinner towards the edges. 



Therefore, they were most likely cut from a larger plate into nearly the final dimensions. The 



average max-min value is very low for hands of type -II, -III and –IV (0.4 – 0.5 mm). Only 



for the hand-protections of type-I this value is slightly higher (0.7 mm). It is interesting to 



note that the average plate-thicknesses of type-III and -IV hand-protections (0.8 – 0.9 mm) 



is lower than the average thickness of the usually older type-I and -II examples (1.2 mm).
S. 141 · Sprachlich überarbeitet · Entwurf

4.3.3.2.4 Neck

[ref_tab_thi_nec] Original Excel Neck protection averages 1.5 mm in thickness.207 The lowest and uppermost lames are generally thinner than the chin plate, although this is not visible in the diagrams, and may have been cut from sheet. The ranges of 1.1 mm for Type I and 1.4 mm for Type II arise chiefly from the chin plate, which appears generally to have been forged to its final dimensions from a smaller blank.

Originalwortlaut vergleichen
4.3.3.2.4 Neck207 [ref_tab_thi_nec] 



The average plate-thickness of Neck-protections is 1.5 mm. The lowest and the most upper 



lame are usually thinner than the plate protecting the chin (not visible in the diagrams ) and 



possibly cut from the plate. The max -min value of 1.1 mm (neck -I) resp. 1.4 mm (neck -II) 



derives merely from the chin-plate, which seems to have been usually forged from a smaller 



plate into the final dimensions.
S. 141–145 · Sprachlich überarbeitet · Entwurf

4.4 Serial production of armour

Direct examination and high-quality photographs of hundreds of objects made detailed comparison possible. Grouping similar pieces revealed that some helmets initially regarded as unique variants actually belonged to larger groups. Their apparently unusual forms resulted from alteration or the loss of visors, forehead reinforcements or separate nape guards.208209

This grouping suggested an unexpectedly limited variety of surviving types. Previous literature implied greater diversity, reinforced by the many forms shown in contemporary art. Some depicted types may indeed be lost; others may be imperfect representations of known forms. The surviving objects nevertheless permit several observations.

If surviving armour represents most former types, the occurrence of nearly identical objects even within this small remainder may indicate fewer late medieval variants than expected. Fourteenth-century armourers may already have made particular models in substantial numbers. Did the processes behind them constitute an early form of serial production?

Little has been written on this subject. Earlier scholarship concentrated chiefly on armour as art, favouring expensive individual commissions over anonymous, plain and inexpensive products. Only one historian briefly discussed documentary evidence for possible serial production in the early sixteenth century.210 Its beginnings remain obscure.

Surviving numbers suggest that output continued to increase until the seventeenth century. The arsenals of Graz, Solothurn, Zürich, Emden (description 1), Schwarzenburg, Munich and Vienna preserve numerous nearly identical sixteenth- and seventeenth-century objects [ref_ill_art_5363] PDF.211 Their quantity alone suggests serial manufacture. Sheet-metal prices were certainly an important factor. Alan Williams attributes the development to the introduction of the presumably more efficient and less expensive indirect ironmaking process:

The most compelling evidence for the use of the Indirect Process is that



the cost of armour fell to a remarkably low level in the 16th century […].



The cost of the cheapest armour becomes so low that the cost of the



metal itself is significant. When the metal used in the cheapest serial-



produced iron armour of the 16th & 17th centuries is examined, it is found



that iron becomes commoner for arsenal armour, and its slag content



increases. The metal used in the later 16th century for Italian arsenal



armour was of lower carbon content than that used in the 15th century



for infantry armour (but still steel rather than iron).
Williams (2003), p. 889. Spacing normalised. 212

Iron and steel production capacity influenced the development of serial armour manufacture, but other technical innovations must also have contributed. The following discussion considers early objects whose close relationships may indicate such production methods.

In German-speaking regions, most fourteenth- and fifteenth-century orders concern individual objects. Orders for large numbers of one type first appear towards the end of the fifteenth century. Northern Italian documents, by contrast, record large orders earlier. Armourers there may have been the first able to equip an army rapidly:

[…] Milan was able, after the battle of Macado in 1427, to furnish within



a few days 4000 suits of armour for cavalry and 2000 for infantry.
Gardner (1898), p. 14. 213

The quality of the cavalry armour is unclear. The 2,000 infantry sets would certainly have been subject to less demanding standards of finish and design: their essential purpose was protection. Several independent workshops probably shared the order, each supplying hundreds of objects. A workshop fulfilling a large commission would have little incentive to produce many different models. Standardised procedures make large quantities economical; variation requires additional planning and skills. If the report is correct, some form of serial production may therefore have existed around Milan by the first half of the fifteenth century. Can surviving objects substantiate it?

The evidence is difficult to assess. Large-scale preservation in arsenals or as dynastic memorials began in German-speaking regions only at the end of the fifteenth century, and no older central European arsenal survives intact. No surviving arsenal assembled in the late Middle Ages contains securely identified serial products from before 1470. Noble guards may have been uniformly equipped, but surviving fifteenth-century inventories of major dynastic collections do not provide extant examples.

Churburg is the earliest relevant armoury. Although it preserves substantial fifteenth-century material, only three late-century helmets closely resemble one another [ref_arm_1859] PDF [ref_arm_1860] PDF [ref_arm_1861] PDF; the remaining objects differ distinctly. Remnants of municipal arsenals also survive in Munich and Vienna. In Italy, no large group of similar objects can securely be traced to a single pre-1470 inventory.

Italian objects now dispersed between collections may once have shared an armoury. Conversely, similar objects brought together in the past two centuries often have different historical origins. Limited numbers and lost or doubtful provenances prevent reconstruction of a sufficiently large group to investigate serial production securely.

Armour found together offers a different kind of evidence. Three major late medieval or early Renaissance armoury finds are known from the central and eastern Mediterranean:

  • The Knights of St John’s armoury at Rhodes passed into Ottoman hands after the city’s capture. Large quantities of forgotten armour entered various collections during the century before this study.214
  • Ottoman war booty was stored in several locations, chiefly the former church of St Irene in Istanbul, before entering the Military Museum (AMI). Many objects also reached European and American collections. Stuart Pyhrr published the only detailed study of this European armour.215 The thousands of stored objects still await comprehensive examination, inventory, conservation and publication. For this study, I examined the European armour on display; much more was expected in inaccessible storage.
  • Approximately 300 armour objects were found in 1840 in the ruins of Chalcis Castle, on Euboea.

For questions of authenticity, the material remaining in Istanbul and Athens is particularly important. These collections are considered free from later reproduction admixture because armour from other sources was neither acquired nor added for centuries.

Chalcis is the only arsenal-like assemblage of early Italian armour covering approximately 1350–1470. The Venetians probably walled it in shortly before the Ottoman capture in 1470; it remained undiscovered until the wall collapsed.216217 Parts of the find were subsequently dispersed. The project database records only the basic information recoverable about these objects’ later histories.

The assemblage still awaits a comprehensive scholarly study. Beyond brief contemporary notices,218 three articles address the subject,219 and some helmets appear in studies with other purposes.220 Two relevant studies survive only as manuscripts in the Royal Armouries Library in Leeds.221222

The find included many European helmets and fragments, sixty-three of which remain in the National Historical Museum in Athens. The MET holds roughly 200 individual pieces, including unpublished arm and leg protection and some helmets.223 Both collections also preserve segmented or brigantine armour. Athens retains neck-defence components [ref_arm_3071] PDF [ref_arm_3079] PDF [ref_arm_3080] PDF and one forearm defence [ref_arm_88] PDF. A preliminary view of the MET limb pieces reveals recurring features suggestive of serial production. Since I did not examine them directly, that question must await further research.

The evident relationships among objects from these three historical assemblages justify considering several helmet groups as possible early serial products. The comparisons below focus on relevant features rather than repeating existing individual descriptions; the object records provide further detail.

I handled many of the helmets personally, permitting close analysis. Most Chalcis examples lack components and may already have been awaiting repair when concealed. Much of the Venetian garrison must have been using other armour during the conflict, so the arsenal originally held considerably more than the material discovered in 1840. The close similarities among several surviving helmets make it almost certain that still more examples of the same models were once present. The Chalcis, Rhodes and Istanbul helmets, together with comparisons from elsewhere, can now be arranged into four broad groups.

Redaktionelle Hinweise · 4
  • „Increase of plate-sheet prices“ steht im Original neben der anschließenden Erklärung durch billigeres Material. Die Überarbeitung nennt den Preisfaktor ohne unbelegte Festlegung der Richtung; Widerspruch fachlich klären.
  • „Macado“ bleibt als Wortlaut des Gardner-Zitats unverändert; keine historische Ortskorrektur ohne Quellenprüfung.
  • Aussagen zu Sammlungszugang, Bestandszahlen und Forschungsstand beziehen sich auf die Dissertation. Die behauptete Freiheit von Reproduktionen bleibt eine Quellenbewertung, keine neue Prüfung.
  • Die Auslegung der älteren Lieferangabe „suits“ als Umfang vollständiger Ensembles ist nicht gesondert gesichert. Der Wortlaut steht im Zitat; im Kommentar wird neutral von „sets“ gesprochen.
Originalwortlaut vergleichen
4.4 The serial208 production of armour 



In the course of this studies, the in situ examination and the very good quality of the images 



taken personally of hundreds of items allowed for a quick and detailed comparison of similar 



items. For this purpose, the objects had to be clustered in groups. Thi s work revealed that 



especially certain helmets – first thought to be of a unique variation of one type – actually 



belong to a larger group of other items. They are today just in an altered condition, lacking 



parts like face-guards, forehead-reinforces or attached nape-guards.209 



To say it in short words: The clustering of extant examples suggested an unexpectedly 



limited type variety. This realization was surprising. The literature on the topic suggested a 



much wider diversity of different types and subgroups. This idea was additionally supported 



by observations in contemporary artworks, where a wide type variety can be found. While 



some of the depicted types might actually have got lost, others might just be misunderstood 



renderings of real existing models. Anyway, according to existing examples some 



considerations might be justified: 



It can be presumed that the existing armour covers the largest part of formerly existing types. 



Now that even within this small leftover several nearly identical items can be fo und, it is 



possible that far fewer type-variations than expected actually existed in the late Middle Ages. 



This would also mean that already the 14 th century armourers obviously produced or



reproduced certain models in large numbers. The question is, if the manufacturing processes 



that created these items were maybe the beginnings of a serial-manufacturing. 



Not much has been written on the serial- or mass production of armour. The main focus of a 



majority of the preceding studies on armour was on aspects of  art and therefore merely on 



the costly and individually made examples. The production of the anonymous, simple and 



cheap armour parts were of lesser interest. Only one historian shortly discussed the sources 



on a possible serial-production of armour in the early 16th century.210 The beginnings of the 



use of serial production methods still remain obscure. 



According to the numbers of extant objects it can be estimated that the production score of 



plate armour until the 17 th century has been permanently increasing. In the “Zeughäuser” 



(Engl. arsenals) of Graz, Solothurn, Zürich, Emden (descr. 1), Schwarzenburg, Munich and 



Vienna, 16th and 17th century armour is still represented in a number of almost identical items 



[ref_ill_art_5363].211 Alone the numbers suggest that it was produced by some kind of serial-



manufacture process. Certainly the increase of plate -sheet prices was one relevant factor. 



According to Al an Williams, the introduction of the presumably more efficient and thus 



cheaper indirect iron-production process was responsible for this development: 



The most compelling evidence for the use of the Indirect Process is that 



the cost of armour fell to a remarkably low level in the 16th century […]. 



The cost of the cheapest armour becomes so low that the cost of the 



metal itself is significant. When the metal used in the cheapest serial-



produced iron armour of the 16th & 17th centuries is examined, it is found 



that iron becomes commoner for arsenal armour , and its slag content 



increases. The metal used in the later 16th century for Italian arsenal 



armour was of lower carbon content than that used in the 15th century 



for infantry armour (but still steel rather than iron).212  



The quantitative capability of the iron or steel production had an influence on the 



development of a serial production of armour, but also other technological innovations surely 



have contributed their part as  well. The following chapter discusses some early items that 



are related so closely to each other that they might have been made by some kind of serial -



manufacturing processes. 



In the German speaking lands in the 14 th and 15th century most of the armour or ders name 



individual items only. The first armour orders that sum up large numbers of one type date 



from the end of the 15th century. At the same time in northern Italy contemporary documents 



tell of armour ordered at once in large numbers. It was probably  in this region where 



armourers were first capable of producing amounts of armour large enough to equip an army 



within a short time:  



[…] Milan was able, after the battle of Macado in 1427, to furnish within 



a few days 4000 suits of armour for cavalry and 2000 for infantry.213  



It is unclear of what quality the delivered cavalry armour was. On the 2000 suits for the foot-



soldiers certainly no great demands concerning their design and quality were made. They



just had to fulfill their protective task. The armou r was probably made by several 



independent workshops, each delivering some hundreds of items. One workshop executing 



a large armour-order was certainly not tempted to deliver the greatest variety of models. Just 



like today, large numbers can only be produc ed economically by means of standardized 



procedures. V ariation is expensive, as new thoughts and skills have to be invested in its 



development. Therefore, – provided that the source for the aforesaid delivery is correct – 



already by the first half of the 15th century some kind of serial production might have existed 



in or around Milan. The question is: Can extant armour prove the assumptive existence of 



such a serial-production process in this time?  



This question is not easy to answer, as the great times o f the arsenal- or memorial-keeping 



of armour began in the German speaking lands at the very end of the 15 th century and no 



older arsenals still exist in central Europe. No existing central European arsenal assembled 



in the late Middle Ages contains definitely serial-produced armour from before 1470. While 



it is possible that some guard-troops of the European nobility have been equipped uniformly, 



the preserved inventories of 15th century items in the great dynastic collections do not contain 



extant examples. The oldest relevant armoury would be that in the Castle of Churburg. While 



a considerable number of armour parts of the 15th century is kept there, the collections 



comprise only three similar helmets of the end of the 15th century [ref_arm_1859] 



[ref_arm_1860] [ref_arm_1861]. All other items are strictly different in their appearance.  



In the German speaking lands some remains of 15th century city arsenals still exist (Munich, 



Vienna). In Italy no large number of similar items that clearly belonged to one  Italian 



inventory assembled before 1470 is found. Some items of Italian make, now kept in different 



collections, possibly once belonged to one Italian armoury. Similar items, now kept together 



in one collection assembled in the last 200 years do often not  come from the same ancient 



armoury-keeping. Due to the limited total numbers of concerned objects and the usually lost 



or doubtable provenances it is not possible to reconstruct a collection large enough to tell 



about the serial production of the contained items.  



This is different with armour -hoards evidently found together. Three large finds of late 



medieval or early renaissance armouries are known, but they were all located in the central 



or eastern Mediterranean region.  



- The armoury of the knights of S t. John in the city of Rhodes fell in Turkish hands 



after the capture of the city. Large amounts of armour were forgotten and came to 



different collections throughout the last 100 years.214  



- The second armoury consists of Turkish war -booty and was stored in different 



locations in the Ottoman Empire – most of it in the former Church of St. Irene in 



Istanbul – before it came to the modern Military Museum (AMI). A lot of the armour 



from St. Irene was brought to the US and Europe and is now found in different 



collections. The only closer study of the European armour from Istanbul was 



published by Stuart Pyhrr. 215 Hopefully one day it will be possible to examine, 



inventory, preserve and to publish the thousands of objects in the storage of the 



Askeri Müze (AMI). For the purpose of this study, the European armour on display 



in this museum has been examined, but much more is expected to be kept in the 



inaccessible museum-storage.



- The third armoury was found in the Castle of Chalcis (or Chalkida) on the Island of 



Euboea. In 1840 approximately 300 armour parts were found in the ruins of the 



former castle.  



For the question on authenticity the items remaining in Istanbul and Athens are of the greatest 



importance, as these collections are certainly not undercut by reproduct ions – no armour of 



other sources was added or bought in for centuries. 



The find of Chalcis can be determined as the only arsenal-like conglomeration of early Italian 



armour from the period between 1350 and 1470. It was probably walled in by the V enetians 



before 1470 – just before the Castle of Chalcis was captured by the Turks – and has not been 



detected by the new rulers until the wall collapsed 216.217 Unfortunately, parts of the find got 



dispersed to different collections. The database built for the purpose of this study can 



comprise only the basic data that could be found about the fate of the different items. The 



topic of the Chalcis finds is still waiting to be discussed scientifically as a whole. After a few 



un-detailed notes of a contemporary of the find218, only three articles were published on the 



subject219, while some of the helmets are discussed in articles with another subject 220. Two 



of these arti cles or monographs are only available as manuscripts in the Royal Armouries 



Library in Leeds221.222  



The hoard comprised many European helmets or their fragments, most of them are stored in 



the National Historical Museum in Athens (63 items). Several unpublished parts of arm- and 



leg-protections together with some helmets are now in the MET (roughly estimated 200 



single pieces). 223 In both collections also some segment - or brigantine armour parts are 



preserved. In Athens there are still parts of neck-protections [ref_arm_3071] [ref_arm_3079] 



[ref_arm_3080] and a single lower arm defense [ref_arm_88]. A superficial look at the limb 



protections of the Chalcis hoard in the MET reveals common features that suggest their 



making in a kind of serial -production process. As the objects were not examined in situ, 



approaches to the answer on this question are subject to future research.  



Due to the evident relationship between many items from the aforesaid three “historical” 



arsenal finds of late medieval European armour, several types and models will be discussed 



in the context of their possible making in early serial -manufacture processes. The 



comparisons of the single items cannot go into every detail and will focus instead on the



relevant features. Most of the objects had been published with single descriptions and there 



is no ne ed to repeat all information here. The object -data sheets provide for some further 



information on the single objects. 



Many of the concerned helmets were personally handled by the author and therefore they 



can be analyzed in detail. As most of the Chalcis helmets are incomplete, it is likely that they 



were waiting for their repair already at the time they were walled in. A large part of the 



V enetian garrison of Chalcis was certainly using further armour in the conflict with the Turks 



and therefore the garris on’s arsenal stock must have contained many more armour parts. 



What was found in 1840 is therefore probably only a small remain of what once existed – 



and as several of the helmets show close similarities, it is almost certain that even more 



helmets of the same model once were kept in the Chalcis armoury. Today, the Chalcis, the 



Rhodes, the Istanbul and comparable helmets from a few other places can be mapped into 



four large groups.
S. 145 · Sprachlich überarbeitet · Entwurf

4.4.1 Type V: the “Chalcis barbuta”

Twenty-one Type V helmets,224 mostly attributed to Chalcis,225 resemble one another closely enough to suggest production in quantity in a single workshop. Each consists of two plates, often with the lower one now missing. None has, or ever had, a visor. All are roughly worked, with no turned edges. Where the lower plate is absent, the burred lower margin of the skull is visible.

Several details nevertheless complicate an interpretation as inexpensive serial manufacture. The skulls vary in pointedness, and producing a pointed form requires more work than a hemisphere. The additional effort probably aimed to improve resistance to downward blows by encouraging a blade or projectile to glance off rather than penetrate.

The forehead openings also differ slightly. Most skulls have only a frontal medial ridge, but some add vertical ridges descending towards the ears [ref_arm_1989] PDF [ref_arm_1991] PDF [ref_arm_2022] PDF. The lining-rivet holes are not arranged uniformly. The right cheek plate of [ref_arm_2144] PDF is hinged, although this may be a modern alteration: the hinge is crude even by this group’s standards and is attached with screws.

Redaktionelle Hinweise · 1
  • Die im Haupttext genannten 21 Helme stehen neben der möglichen Reduktion auf 18 in Anm. 225, deren Zählweg nicht vollständig erläutert ist. Beide Quellenangaben unverändert erhalten.
Originalwortlaut vergleichen
4.4.1 Type-V: “Chalcis barbuta” 



21224 helmets of type-V225, most of them from Chalcis, are so similar to each other, that they 



might have been produced in large quantities in one workshop. They consist of two plates 



only, none has or had a visor attached and often the lower plates are lost. All helmets are 



crudely worked, no edge is turne d. At the examples where the lower plate is missing the 



burred lower edge of the skull is visible.  



However, there are actually features at these helmets that contradict their assumptive 



production by cheap serial-manufacture processes: The helmets are not all exactly the same. 



The skulls are pointed to a varying degree. Producing such a shape is also more difficult than 



making a simple hemispherical skull. The reason for the acceptance of this “more” of work 



is probably the intended advancing of the helmet ’s resistance against vertical blows from 



above – a pointed skull would hopefully make a blade or projectile slide off, instead of 



penetrating the helmet. In addition, the examples differ slightly in the shape of their cutouts 



above the eyes. While many have only one frontal medial ridge, some of the skulls show at 



each side additional vertical ridges from the point towards the ears [ ref_arm_1989] 



[ref_arm_1991] [ref_arm_2022]. Furthermore, the arrangement of the holes for the lining -



rivets is not the same at all the helmets. The helmet [ ref_arm_2144] at the rig ht side has a 



cheek-piece attached by a hinge. This could also be a modern restoration as the hinge is 



worked even too crudely for these helmets and it is attached by screws.
S. 146–147 · Sprachlich überarbeitet · Entwurf

4.4.2 Type II: the “Chalcis closed helmet”

A fragmentary group226 of twenty-seven Type II helmets227 similarly raises the possibility of early serial manufacture.228 Like the Type V group, each has a skull made separately from the lower plate. The lower portion generally flares further at the nape and closes on the right of the chin with an articulated plate secured by a rotating pin. A visor pivots at the sides of the skull.

Only [ref_arm_4408] PDF appears complete in original condition. The other two complete examples, [ref_arm_1458] PDF and [ref_arm_1590] PDF, have been extensively repaired and supplemented. The group also varies: cheek plates differ in size, visor outlines differ, and sight is provided through either one slit or two. The visor [ref_arm_1455] PDF consists of two vertically arranged plates, an unusual construction for the period. The skull [ref_arm_1452] PDF carries a medial band rising to a point at its centre. Skull points and forehead openings also vary, but the technical system and overall appearance remain closely related. For objects represented only by detached visors, that relationship can only be inferred.

Two comparable skulls may be reused older Type V helmets. A relief [ref_ill_art_5399] PDF (description 1) shows the rear of an eight-faceted pointed helmet resembling [ref_arm_1985] PDF. Despite damage to the latter’s lower edge, a slightly flared nape guard remains. The MDA example [ref_arm_2157] PDF shares this feature and preserves details perhaps lost from the Athens helmet.

Some studs for a ring-armour collar remain on the MDA skull. Corresponding larger holes run around the lower edge of the Chalcis example, above small holes used to stitch in the lining. Both helmets have a change in the height of the lining-hole row above the eyes, two unexplained holes in the frontal medial ridge, and lateral visor-pivot holes.

The same artwork shows an articulated face guard beside a comparable helmet [ref_ill_art_5399] PDF (description 2). The Athens and Paris objects may therefore originally have had visors; if so, they are the earliest surviving examples. Because its flared nape edge was not removed to fit a lower plate, [ref_arm_1985] PDF was probably never converted into a Type II closed helmet.

The related [ref_arm_1453] PDF may instead have undergone conversion. Small lining holes run along its lower edge, and a visor-arm fragment remains pivoted on the right. The lower margin appears trimmed, perhaps removing an earlier flare. Holes beside the former collar-stud holes probably secured a new lower plate.

Another faceted, trimmed skull in the MET [ref_arm_1620] PDF lacks both visor and collar-stud holes. This may result from ill-informed repair, since the helmet could not function in its present state: there are no suitable lining holes. Whether a lower plate was added later is likewise uncertain, although the roughly cut lower margin makes that possibility very likely.

Dating remains controversial.229 The capture of Chalcis in 1470 provides a secure terminus ante quem for objects from the find, but few comparable contemporary depictions exist. Paul Martin and Jean-Pierre Reverseau date faceted examples to around 1345.230 The absence of turned edges may indicate manufacture before 1400 or inexpensive production at a later date.

The shared features and discovery of so many helmets together suggest that they were purchased together, making manufacture within the orbit of one workshop very likely for each group. The location remains uncertain. Only one Type II example has two visible identical marks, a crowned P or R [ref_arm_1458] PDF. Crowned-letter marks are common on Italian, particularly Lombard, armour, and marks identify many other Chalcis objects as northern Italian.

These helmet forms nevertheless do not appear in Italian or northern Alpine art. Two comparable helmets securely outside the Chalcis find,231 [ref_arm_2072] PDF and the Type II [ref_arm_4460] PDF, were found in Istanbul and Cyprus respectively. Boccia’s proposed Aegean manufacture is therefore plausible.232233

Serial production cannot be established with certainty for any variant. The similarities within each group nevertheless indicate some uniformity of equipment among late medieval soldiers, at least in Catholic stronghold garrisons in southeastern Europe. Modern standards of interchangeability should not be imposed on this evidence. To contemporary users, these helmets would have counted as the same model, despite the absence of binding European standards.

Originalwortlaut vergleichen
4.4.2 Type-II: “Chalcis closed helmet” 



A fragmentary226 group of 27227 type-II helmets also raises the question on the possibility of 



them being produced in an early serial -manufacture process.228 The skulls of these helmets 



are – similar to those of the type -V helmets discussed before – worked separately from the 



lower plate. The latter is a bit different: It usually flares out more at the nape and it is closed 



by an articulated flap at the right side of the chin, secured by a turning pin. Additionally, the 



face is protected by a visor with pivots at the sides of the skull. On ly one of these helmets 



seems to be complete in an original condition [ ref_arm_4408]. The further two complete 



examples [ ref_arm_1458] and [ ref_arm_1590] were intensively repaired and completed. 



Also all of these hel mets differ slightly from each other: The cheek -pieces are of different 



size. The edges of the visors are of different shape, the vision is either  made by a single or 



by two slits. The visor [ ref_arm_1455] is made of two vertical plates – a very uncommon 



construction for a face -guard of the time. At the skull of [ ref_arm_1452] a medial band 



forming a point at the center of the skull is attached. The skulls differ slightly in the shape 



of their points and the design of the cutouts at the forehead. Nevertheless, the technical 



system is the same with all the helmets and the general appearance is very similar (for the 



lost helmets of which only the visors remain this can only be presumed). 



Two further, in shape similar skulls have to be discussed. They are maybe re -used older 



helmets of type-V . The relief [ref_ill_art_5399] (descr. 1) on the right side shows the rear of 



a helmet with an 8-time faceted pointed skull similar to [ref_arm_1985]. The lower edge of 



the latter is badly damaged, but at the rear of the helmet a nape -guard slightly flaring out is 



still visible. This feature is also observed at a similar example from the MDA [ref_arm_2157] 



which additionally shows some features now possibly lost at the Athens item. At the MDA 



skull some of the studs that once held the leather or plate strap for the attachment of a ring -



armour collar are still in place. They once were fitted to the larger holes encircling the lower 



edge upon the line of small holes at the Chalcis example. The small holes served for the 



stitching of the interior lining. Exactly like at the MDA helmet also at [ref_arm_1985] there 



is a height-offset in the line of these small holes above the eyes. The frontal medial ridge at 



each is pierced by two holes of unknown purpose. At both helmets the side of the skull is 



pierced with holes for the visor -pivots. Next to a similar helmet o n the right side of the 



aforesaid artwork [ ref_ill_art_5399] (descr. 2) at the left side a helmet with an articulated 



face-guard is shown. Therefore, it is possible that the Athens and the  Paris items originally 



were fitted with a visor. If this is correct then they are the earliest examples to survive. As 



the flaring nape-guard was not cut off for the easier attachment of a lower plate, the Athens 



helmet [ ref_arm_1985] probably was never turned into a helmet of the type -II “closed 



helmet” group. This is probably different with the second similar helmet [ref_arm_1453]. It 



also shows a line of small lining holes along the lower edge. At the right side of the skull a 



fragment of the visor-arm is still fastened by its pivoting rivet. The lower edge – maybe once 



flaring out at the nape – looks like it has been cut off. The holes drilled next to the  former



stud-holes probably once held rivets that fixed a lower plate. A further, similar helmet with 



a faceted skull and a trimmed lower edge is kept in the MET [ ref_arm_1620], but it lacks 



the holes for a  visor and the collar -studs. This could derive from misunderstood repairing, 



as the helmet would actually not work in the current condition. No holes suitable for an 



interior lining are visible. Therefore, it is also not clear if the helmet had secondary a lower 



plate attached. Nevertheless, as the lower edge had been trimmed very crudely this 



possibility is very likely. 



The dating of all the discussed type -II helmets is discussed very controversially. 229 The 



capture of the city by the Turks in the year 1470 provides for a reliable terminus ante quem 



for the dating of all objects found. It is difficult to date these helmets, as almost no 



comparable depictions in art have been found yet. According to Paul Martin and Jean-Pierre 



Reverseau the items with the face ted skull would date about 1345. 230 That none of the 



helmets shows a turned edge either speaks for them being made before 1400, or again for 



their production in cheap serial-manufacture maybe also in later times.  



Additional to their similarities, the fact that so many helmets were found together in Chalcis 



– and thus were probably once bought together – makes the production of each group in the 



surroundings of one workshop very likely. Where the helmets were actually made is unclear. 



Only one of the type-II examples bears 2 identical visible marks – a “P” or an “R” under a 



crown [ref_arm_1458]. Marks with letters under a crown are often found on Italian – more 



precise Lombardian – armour. Due to their marks ma ny other items from Chalcis were 



actually made in the northern Italian region. Nevertheless the aforesaid helmets never appear 



in Italian or northern alpine artworks. As two of the few similar helmets that clearly not 



belonged to the Chalcis hoard231 – [ref_arm_2072] and type-II [ref_arm_4460] – were both 



found in the eastern Mediterranean sea (Istanbul and Cyprus), it is well possible that Boccia 



is right in suggesting their production in the Aegean region232.233  



Even if for none of the helmet -variations a serial production can be attested with absolute 



certainty, the similarity of the helmets within the single groups are an evidence for a 



somehow uniform equipmen t of the late medieval soldiers – at least for those serving in 



southeastern Europe in catholic -christian stronghold-garrisons. Historical artifacts should 



not be met with modern standard-criteria. For the contemporaries the discussed helmets were 



identical, eventually there were no binding European norms existing.
S. 147–148 · Sprachlich überarbeitet · Entwurf

4.4.2.1 Manufacture of the two preceding groups

The skulls of both types are made from very thick plate, averaging about 3.0 mm, whereas the lower plates and visors average about 1.5 mm. Rough exterior surfaces survive on unrestored helmets and even on examples “polished” in recent years. They suggest that the plates were originally left unground, with a black surface.

Attaching a simple, thin plate to protect the nape and cheeks to a thick skull offers a quick, inexpensive way to make an effective helmet extending low around the head. Such construction also permits a division of labour: one worker could hot-form the rough skulls, another finish them cold, a third prepare the lower plates and a fourth assemble the components. Type II additionally requires visors. These are only slightly embossed and use thin plate that could also be worked cold.

Making the same helmet from a single plate requires substantially more work and keeps one worker occupied with hot forging for longer. It consumes more charcoal, and more hearths are needed if several workers are to make helmets simultaneously.

Originalwortlaut vergleichen
4.4.2.1 The making of the two aforesaid groups 



The skulls of both types are worked from very thick plate of about 3.0 mm in average, while 



the lower plates and the visors are made of thinner material, about 1.5 mm in average. The



rough exterior surfaces found at the not restored and even at the helmets  “polished” in the 



last years, suggest that originally the plates were not ground and had a black appearance.  



The system of making a low reaching helmet by attaching a simple nape and cheek protecting 



thin plate to a skull made of a thick plate is a cheap  and quick way to produce a sufficient 



helmet. One worker can make in hot -work the rough shape of the skulls, one can finish the 



skulls cold, another one can prepare the lower plates and a fourth man can mount the parts. 



At the type -II helmets additionally  the visors have to be produced. They are only slightly 



embossed and made of thin plate that could also be worked cold. To make the same helmet 



from one single plate is much more work and keeps one worker busy with hot -work for a 



long time. This is consumi ng more charcoal and more smith’s hearths are needed to have 



several people making helmets at the same time.
S. 148–149 · Sprachlich überarbeitet · Entwurf

4.4.3 Type V: the “Chalcis basinet-barbuta”

A third group comprises seventeen helmet skulls,234 about half from Chalcis or attributed to that find. All extend low around the head and are made from a single plate. They narrow below the ears before flaring into a nape guard. None has a turned edge, and all have a central point except [ref_arm_4267] PDF and the damaged [ref_arm_2128] PDF.

Although nearly identical in shape, the skulls differ in their fittings. Some retain studs, or the holes for them, along the lower edge for attaching a ring-armour collar. A row of small holes beside the edge served to stitch in the lining. Others have only a row of lining-rivet holes encircling the skull at ear level: [ref_arm_1986] PDF [ref_arm_1993] PDF [ref_arm_2000] PDF [ref_arm_2008] PDF [ref_arm_2095] PDF [ref_arm_2097] PDF [ref_arm_2129] PDF and [ref_arm_2145] PDF. On [ref_arm_2128] PDF and [ref_arm_2183] PDF, the studs still hold fragments of wire and a metal strip to which the ring armour was linked.

Every helmet prepared for a ring-armour collar also has holes, or surviving hooks and pins, for a centrally pivoted visor. No surviving visor can be securely assigned to this model. Except for [ref_arm_1981] PDF and [ref_arm_4267] PDF, these skulls have a medial ridge on their upper portion. Helmets without provision for a ring-armour collar appear also to have lacked a visor, since no attachment features are recognisable.

Among the latter group, only [ref_arm_2159] PDF has a medial ridge. It is an exceptional variant in other respects too. Although the overall skull shape is nearly identical, it has a turned lower edge, an embossed medial ridge on the upper skull, a small projection above the eyes and a visor pivoted at the sides. These features are absent from the other comparable helmets. It may represent a transition from the Chalcis models to the classic “barbuta”. Comparison with an early example [ref_arm_2156] PDF supports this suggestion: both have a similar T-shaped face opening and four holes of unknown purpose on the forehead. The helmet [ref_arm_2008] PDF alone had a small hinged cheek plate on the right, now missing; its skull is also the only one faceted by eight ridges.

All these helmets were either raised or deep-drawn from a single sheet. The maker may first have formed a closed vessel and then cut out the face opening. Rough surfaces, especially on helmets without ring-armour collar fittings, suggest that these too may have remained unground and unpolished. The absence of turned edges suggests an early date, probably between 1380 and 1420. Their one-piece construction, face openings and elegantly narrowing contours closely resemble later Italian Type V helmets—the classic “barbuta”—some of which also come from Chalcis.

The variants with ring-armour collar fittings are probably later. The only example combining features of both variants, [ref_arm_1981] PDF, lacks a medial ridge, as do the helmets without collar fittings. It may therefore originally have been made for an interior lining alone and subsequently fitted with collar studs. Alternatively, the two variants may have been contemporary, with ring-armour collars reserved for wearers of higher rank.

Redaktionelle Hinweise · 3
  • Die Grundbeschreibung „keine umgelegten Ränder“ wird später durch ref_arm_2159 ausdrücklich eingeschränkt; diese Ausnahme bleibt sichtbar. Ebenso ist dessen Visier eine Ausnahme zur vorangehenden Gruppenbeschreibung.
  • Die Originalpassage „a small nose at the edge above the eyes visor with pivots“ ist syntaktisch beschädigt. Als Aufzählung von Stirnrandvorsprung und seitlich gelagertem Visier gelesen; am Objekt fachlich bestätigen.
  • Die Anmerkung zählt 17 Objekte auf, während der Haupttext weitere IDs nennt. Umfang und Abgrenzung der Vergleichsgruppe sind zu klären; keine IDs ergänzt oder gestrichen.
Originalwortlaut vergleichen
4.4.3 Type-V “Chalcis basinet-barbuta” 



A third group of 17234 helmet-skulls, about half of them are from Chalcis or attributed to this 



find, will be discussed in the following paragraphs. The similarity of all helmets is their low 



reaching skull made from one plate, tapered below the ears and thus forming a flaring nape-



guard. No plate -edge is turned and – with the exception of [ ref_arm_4267] and  



[ref_arm_2128] (damaged) – all skulls have a central point. In shape nearly identical, some 



are equipped along the lower edge with studs or at least the holes are visible. Here a ring-



armour collar was attached. A row of small holes for the lining-stitching is visible along the 



edge. Other helmets have only a row of holes for the lining rivets encircling the skull in the 



level of the ears [ ref_arm_1986] [ ref_arm_1993] [ ref_arm_2000] [ ref_arm_2008] 



[ref_arm_2095] [ ref_arm_2097] [ ref_arm_2129] and [ ref_arm_2145]. At [ ref_arm_2128] 



[ref_arm_2183] the studs still retain fragments of wire and a plate strap to which the ring -



armour was linked. All helmets prepared for the attachment o f ring-armour also show the 



holes or still the hooks and pins for the attachment of a central pivoting visor, of which no 



extant example can be attributed to this helmet -model. The latter variations – with the 



exception of [ref_arm_1981] and [ref_arm_4267] – have a medial ridge at the upper part of 



the skull. The helmets that never had a ring -armour collar do not seem to have had a visor 



too, as no features for its attachment are recognizable. Of this variation only [ref_arm_2159] 



has a medial ridge – anyway a unique variation of this group. While the general shape of the 



skull is nearly identical, this helmet has the lower edge turned, a medial ridge embossed at 



the upper skull, a small nose at the edge above the eyes visor with pivots at the side of the 



skull. These features cannot be found at any comparable helmet. It is possible that this is a 



transitional t ype from the Chalcis models to the classical “barbuta”. This assumption is 



supported by a comparison of the visored helmet to the example of an early barbute 



[ref_arm_2156]. Both helmets have the same four holes of unknown purpose placed at the 



forehead of the skull and a similar t-shaped face-opening. The helmet [ref_arm_2008] is the 



only one that had a hinged small cheek-piece at the right side – now missing. Its skull is the 



only example faceted by 8 ridges.  



All aforesaid helmets were either raised or deep -drawn from one plate-sheet. Maybe first a 



closed vessel was produced and then the face opening was cut. As especially the helmets 



without a ring -armour collar attachment still have a rough surface, it is possible that they 



were also not ground and polished. The absence of turned edges suggests an early date, 



probably between 1380 and 1420. Their making from one plate, the shape of the face cutout



and the elegant tapering is very similar to later Italian type-V helmets, the classic “barbuta”, 



of which also some examples come from Chalcis.  



The examples with a ring-armour collar attachment are probably the younger variations, as 



the only exponent with the features of both variations has no medial ridge [ref_arm_1981] – 



just like the helmets without a ring -armour collar. Therefore, it is possible that this helmet 



was first produced for the attachment of an interior lining only and was later fitted with studs 



for the fixation of a ring -armour collar. It is also possible that the helmet variations were 



made about the same time, but those equipped with ring-armour were reserved to wearers of 



a higher rank.
S. 149–152 · Sprachlich überarbeitet · Entwurf

4.4.4 Type VII: a possible serial product

A group of about fifty Type VII helmets probably provides the strongest evidence that Italian workshops had adopted some form of serial manufacture before 1470. Most of the simpler examples come from Chalcis, Rhodes or Istanbul. Each consists of at least three plates: a hemispherical skull with a medial ridge235 and a burred lower edge; a forehead reinforcement riveted to the skull; and a flared nape guard that pivots slightly on two rivets beside the ears. Both attached plates have inward-turned lower edges.

Several variants exist. The standard examples are very simple [ref_arm_1750] PDF [ref_arm_1777] PDF. Others have decorative copper-alloy rivet caps [ref_arm_1721] PDF, concave decorative cut-outs along the upper edge of the forehead reinforcement [ref_arm_2010] PDF, or a nape guard made from several lames [ref_arm_1887] PDF. Later examples may have several ridges on the skull [ref_arm_1751] PDF, or engraved and gilded surfaces [ref_arm_1855] PDF. Some were therefore too costly for production in large quantities. Their shared construction nevertheless supports the following general interpretation of manufacture.

The frequently unfinished lower edge of the skull, concealed by the attached plates, is particularly revealing. A separate forehead reinforcement was not essential: leaving the skull thicker in that area could have provided a similar effect. The nape guard could likewise have been formed in one piece with the skull. A likely explanation for the separate construction is division of labour, with a worker or group responsible for each component.

Specialisation could reduce production costs. A simple hemispherical skull is easier to form than a one-piece helmet with a flared nape guard. Adding a reinforcement also permits a thinner skull plate, which is easier and quicker to work. Workers could make the attached plates cold, including their turned edges, reducing the number of hearths required. Others could grind and polish the components, leaving only minor adjustments during assembly.

A publication by the IWF in Göttingen suggests a specific way in which the most labour-intensive components—the skulls—might have been made in batches. Its film [ref_vid_buc] and accompanying article236 document bucket-making around Bienno in the Italian province of Brescia. As late as the 1960s, workers there made builders’ buckets from single sheets of iron using water-powered hammers. At the time of this study, the hammers still operated for museum demonstrations.237 The region has a metalworking tradition extending over more than 2,000 years, including the manufacture of high-quality arms238 and armour.239 The filmed procedures could also have produced the basic form of a helmet and therefore warrant detailed examination.

Unlike raising, in which most blows are applied to what becomes the exterior, this process forms the vessels from within, using a technique comparable to deep drawing. Its principal advantage is the ability to form several objects together: the film shows seven buckets made at once. Considerable strenuous manual work remains, but the water-powered hammer greatly reduces it.

First, sheets are selected from storage and placed beside the hearth. Several are heated together. The anvil and hammer head are prepared for the first forging operation, and a trial run checks their alignment. A heavy second hammer, suspended on a chain from the ceiling, is used to drive the main hammer backwards into position. The hammer is also moved along its pivot axis to centre it above the anvil.

The worker brings the first red-hot sheet to the hammer with tongs. Water carried through small channels cools the open bearings, while a swab continually greases the lifters that operate the hammer shaft. The square sheets are drawn out to enlarge them, thin them towards the edges and give them a round outline. Careful manipulation with the tongs produces an evenly shaped blank.

Since both hands hold the workpiece, the worker uses his left leg to control a lever that starts and stops the hammer and regulates its frequency. The lever opens a sluice in the channel outside the mill, admitting water to the wheel. A stone weight closes the sluice when the lever is released, slowing or stopping the hammer. During this operation, the worker sits to the left of the anvil.

A second worker trims the uneven margins with water-powered shears, then sorts the blanks by size and shape. Before reheating, the sheets are dipped into a liquid mixed in a deep pit, probably containing clay and charcoal. This coating is intended to prevent the sheets from welding together.

Two red-hot sheets are then drawn out together. Their diameter increases and their thickness decreases, especially towards the outer edge. Working them together speeds the operation: the larger volume retains heat longer, and bumps or thicker areas are easier to level. The edges are trimmed again.

Seven prepared sheets are heated to red heat. A worker lifts them with tongs and slides them from the furnace support into a stone pit in the floor. A few hand-hammer blows deform the stack so that it holds together during forging. The water-powered hammer then forms the bundle into a shallow pan. For this operation, its head has been changed to an elongated form with a rounded striking end.

Each resulting pan is dipped in the same liquid, as are seven of the previously prepared blanks. These are placed inside the pan and compressed in a simple wooden press. The pan’s rim is hammered inwards to retain them. Its underside is also coated before the package returns to the furnace, probably to prevent it from welding to the furnace grate.

Once red-hot, the package is slid back into the floor pit. Three men roughly form it into a hemisphere with heavy hand hammers. Heat and hammering loosen the stack, which is tightened again with a few blows.

The main deep-drawing operation follows. The package is continually rotated under the hammer. Special tongs reach over the rising rim and are exchanged for larger ones as work progresses. One man operates the hammer and another handles the workpiece. Starting at the widest circumference, the worker gradually moves towards the centre. Repeated circular passes turn the sheets into deep bowls.

At the required depth, the bundle is reheated and shaped into a truncated pyramid with the aid of a trapezoidal plate. To remove the outer pan or mould, the buckets are suspended between a support and a hook and the folded edges are bent back. The seven buckets can then be separated. A few blows from the large hammer, fitted with another suitably shaped head, flatten the sides of each.

Apart from the final pyramidal shaping, these workpieces closely resemble helmet blanks. If water-powered hammers were used in this way to make helmets, their role probably ended at approximately this stage. Further shaping and planishing would likely have been done by hand, with the heated skull worked from the outside. The forming techniques are nevertheless comparable to those used for the buckets. A helmet of the group discussed here would probably be easier to shape, since its shallower bowl requires a smaller sheet and reaches the necessary depth sooner. Its lower edge need not be trimmed or ground: the attached plates and the internal leather lining band would conceal it.

The trip hammer’s limitations would prevent it from bringing the blank much closer to the finished helmet shape. Each skull would therefore need individual hand-finishing: embossing the ridge and smoothing the surface with a smaller hammer. All surviving helmets of this type were most probably also ground and polished.

Other workers could make the nape guard and forehead reinforcement cold. Their thin plates, averaging 1.0 mm, could be shaped and their edges turned without heating. A greater difficulty was probably distortion caused by the stresses introduced when the edges of an already shaped plate were turned. The edges may instead have been turned first and the plate shaped afterwards.

Some nape guards clearly have wire inside the turned edge [ref_arm_2015] PDF. The wire allows later adjustment without flattening the turn. A hollow turn, by contrast, can crease or flatten when the plate is hammered into shape.

There is no conclusive evidence here that these methods were used for armour, although they may originally have been developed for that purpose. Research into the history of the region’s hammers might reveal documentary evidence for a transition from armour production to bucket-making.

The Chalcis finds demonstrate how much remains unknown about late medieval armour. The objects in Athens are unique, unrestored and part of one of the largest directly associated assemblages ever discovered. They raise numerous questions for further research.240

Redaktionelle Hinweise · 3
  • Die Übertragung der im Film dokumentierten Eimerherstellung auf mittelalterliche Helme bleibt eine Hypothese, kein Produktionsnachweis. „Deep drawing“ ist der Vergleichsbegriff der Dissertation, nicht ohne Weiteres die moderne industrielle Tiefziehtechnik.
  • Die Zahl von sieben gemeinsam gefertigten Eimern und der Ablauf mit einer zusätzlichen äußeren Formplatte bleiben erhalten. Die genaue Zusammensetzung der einzelnen Zwischenpakete sollte bei einer erneuten Filmsichtung überprüft werden.
  • Zeitgebundene Hinweise auf Vorführungen und regionale Produktion beziehen sich auf den Forschungsstand der Dissertation.
Originalwortlaut vergleichen
4.4.4 Type-VII “serial product” 



A group of ca. 50 type -VII helmets probably provides the strongest evidence that already 



before 1470 Italian workshops had adopted some kind of serial-manufacture processes. Most 



of the simple models of the compared examples either come from Chalcis, Rhodes or 



Istanbul. All the concerned helmets are made of at least three plates: The hemispherical skull 



with a medial ridge 235, the lower edge left burred, a forehead reinforce riveted to the skull 



and an attached, flaring nape protection, slightly pivoting at two rivets at the ears – the latter 



plates both have an inward turned lower edge.  



There are actually different variations of this helmet existing. The classical examples are 



very simple [ ref_arm_1750] [ref_arm_1777]. The rivets can have decorative copper alloy 



caps attached [ ref_arm_1721], the forehead reinforce sometimes has decorative  concave 



cutouts at its upper edge [ ref_arm_2010], the nape -guard consists occasionally of several 



lames [ ref_arm_1887], at later items the skull can even b e decorated by several ridges 



[ref_arm_1751] and the surface can be decorated by engraving and gilding [ref_arm_1855]. 



Therefore, some of the considered helmets were too costly to be produced in large quantities, 



but nevertheless, the system in which all the helmets were constructed support the following 



general assumptions on their making.  



Particularly the often unfinished lower edge of the skull – covered by the aforesaid attached 



plates – brought up some questions on the making of these helmets. The forehead reinforce 



is not necessary, as the plate of the skull could simply have been left thicker – with a similar 



reinforcing effect. The nape -guard could ha ve been worked in one piece with the skull as 



well. The answer is probably simple: The helmets were made in manufacture -processes 



using the division of labor. For the making of each part of the helmet a certain worker or 



group was responsible. Production c osts could be reduced by the specialization of the 



workers to one process. Making a skull of only a simple hemispherical shape was easier than 



forming a helmet in one piece with a flaring nape -guard. Furthermore, the attachment of a 



reinforce-plate allowed for the use of thinner plate for the skull, which in turn reduced the 



time for the making of the latter. Thin plate was worked easier than thick plate. The number 



of necessary smith hearths in the workshops was reduced, as the workers made the attached 



plates in cold work. They also already turned the edges where necessary. Other workers 



ground and polished the single parts. Only little adjustment-work had to be carried out when 



the parts were mounted.



An interesting publication brought up concrete ideas on how the most laborious parts – the 



skulls of helmets – could have been produced in series: The IWF -Göttingen published a 



video [ref_vid_buc] and an article 236 on the making of buckets in the Italian province of 



Brescia in the area of the village of Bienno. As late as the 1960ies in this area buckets for 



mason-work were made from one sheet of iron plate – with the help of waterpowered 



hammers! Until today, for museum-events237 the hammers do still work. The area for more 



than 2000 years – until today – was famous for the making of all kind of metalworking, 



traditionally quality arms238 and armour239. The working processes seen in the video are very 



simple to explain. Without restrictions, the same procedures could have been undertaken to 



produce the basic shape of a helmet and therefore the bucket -making will be discussed in 



detail. 



Unlike the technique of raising a helmet, where most of the work is done from the later 



outside of the item, the buckets were made by a kind of deep -drawing process where the 



object is worked from its interior. The main advantage of the bucket-making technique was 



the forming of a huge number of objects at a time. In the video the men make seven buckets 



at one go. The handwork ratio throughout the process is still tough, but it is largely reduced 



by the help of the waterpowered hammer.  



At first, from a store the plates are chosen and placed besides the smith’s hearth. Several 



plates are inserted at a time in the hot oven. The anvil and the hammer head are prepared for 



the first forging process. The correct setup is controlled by a test -run of the hammer. The 



precise position of anvil and hammer is adjusted by moving the hammer backwards with the 



help of a heavy second hammer, swinging at a chain from the ceiling. Additionally the 



hammer is moved along its turning axle to remain centrally over the anvil. The first red hot 



plate is brought to the hammer with the help of tongs. The open bearings of the hammer are 



cooled by water, running through small channels to the necessary spots. The lifters operating 



the shaft of the hammer are permanently greased by a swap. The square plates are drawn out 



to reduce their thickness towards the edges, to enlarge their dimensions and to reveal a round 



shape. For the result of an equally dimensioned plate the worker is moving it very carefully 



with his grippers.  



As the worker needs both hands for holding the work -piece, he regulates the start, beat -



frequency and stop of the hammer via a handle operated by his left leg. The handle opens a 



water shutoff at the channel outside the mill, whose stream turns the mill -wheel. A stone 



serves as a weight for the closing of the shutoff. The worker thus only has to release th e 



handle to slow down or to stop the hammer. For this work he is sitting at the left side of the 



anvil.  



A second worker takes the drawn out plates to a waterpowered shear and cuts off the uneven 



edges. Subsequently the plates are sorted by size and by shape.  



In a deep pit, a liquid, probably consisting of clay and charcoal, is mixed to which the plates 



are dipped before put in the oven. The liquid should prevent them from welding together 



when heated. Two plates at a time are drawn out red -hot under the h ammer. This increases 



their diameter and makes the plates thinner, increasingly towards their outer edges. Working



two plates together makes work quicker as more volume keeps the heat for longer time and 



bumps or thicker parts are easier leveled out. After this process the plate edges are cut again. 



Seven of such plates are heated in the oven until red hot. A worker takes them off with tongs 



and lets them at once slide down from the support of the oven into a stone pit on the floor. 



The men blow their hammers a few times onto the plates to deform them so they stay together 



when forged. Then, with the help of the waterpowered hammer, the bundle is formed into 



the shape of a pan. For this process the workers had changed the peen of the hammer to an 



oblong mouth, rounded at the hitting end.  



Each of these pans is dipped into the liquid described above, just as well as seven of the 



plates from the first go. The latter are then placed in the pan and pressed together by a simple 



wooden press. The rim of the pan is then beaten inwards to hold the plates together. The 



bottom of this “package” of plates is also treated with the liquid before it is placed in the 



oven. The liquid should probably prevent the pan from welding to the grill of the oven. 



When completely red hot, the package is taken off the oven and slide again into the pit. Three 



men give it a rough hemispherical-shape by the blows of heavy hammers. The package got 



splayed from the heat and the hammering and needs to be tightened by a few hammer-blows.  



Then the actual deep-drawing process starts. The package is worked under the hammer and 



permanently turned circular. The men make use of special grippers that reach over the 



upwards bending rim, throughout the process they are exchanged by larger examples. One 



man is operating the hammer and a second one handles the buckets. The worker begins from 



the largest circumference and slowly works towards the center. By the repetition of the 



circular beating the plates are shaped into deep bowls. When the desired depth is reached, 



the bundle is heated again and by means of a trapezoid plate beaten into the shape of a 



truncated pyramid. The “pan” or mold is taken off by hanging the buckets between a support 



and a hook and bending back the banked edges. Now, the seven buck ets are separated. The 



sides of each are made even by a few beats of the big hammer, whose head had been 



exchanged to another of the required shape.  



The revealed work-pieces – with the exception of the pyramidal shaping – resemble exactly 



a pre product of  a helmet. If the technique of the waterpowered hammer was ever used in 



the described way for making helmets, it is very likely that its use ended in more or less the 



same stage. Further shaping and planishing needed to be made by hand probably. The helmet 



needed to be heated and worked from the outside. The techniques applied to get to the final 



shape of a helmet -skull are nevertheless the same like those of the bucket -making. It is 



probably even easier to shape a helmet of the group mentioned above, as th e required 



dimensions are smaller, i. e. the bowl is less deep, and therefore a smaller plate can be used 



and the depth is reached much quicker. There was no need to cut or grind the lower edges of 



the skull, as they got covered anyway by the attached plates and by the interior leather strap 



for the lining. 



Due to the limitations given by the trip hammer, a work piece for a helmet cannot be refined 



much closer to the final shape. This means that each helmet had to be finished singly by 



hand. The ridge had t o be embossed and the surface had to be smoothed by a smaller hand 



hammer. All extant helmets of this type were most likely also ground and polished.  



Other workers could make the nape -guard and the reinforce without a need for heating the 



plate. The required shaping could easily be done cold. Even the turning of the edges needs 



no heat, particularly as the plates of the concerned helmets with 1.0 mm average are very 



thin. The biggest problem in the making of these attachments was probably rather the 



deformation of the ready shaped plate through the tensions rising in the material when the 



edges were turned. It is also possible that first the edges were turned and then the plate was



brought in shape. Some nape -guards do obviously have a wire inserted in the turned edge 



[ref_arm_2015]. This allows a later adjustment of the turn without punching it flat. A hollow 



turn can either crease or become flat if the plate is shaped by hammer.  



While the final evidence ca nnot be cited here, it is of course well possible that these 



techniques were once developed for the production of armour. Future research can focus on 



the history of the hammers of the region; maybe the shifting from armour- to bucket-making 



in the concerned region can be reconstructed by documentary evidence.  



The open questions on the very important Chalcis finds – those in Athens are unique, 



unrestored, and belonging to one of the largest directly associated hoards ever found – serve 



as a demonstrative e xample that the knowledge on late medieval armour is far from being 



complete. Especially on the Chalcis finds a number of open questions demand further 



research.240
S. 152–159 · Sprachlich überarbeitet · Entwurf

4.4.5 Central Europe

Surviving early armour in the Italian style often shows close similarities. By the late fourteenth century, Type IV helmets—the earliest armour type to survive in substantial numbers—already included almost identical pointed examples [ref_arm_1495] PDF [ref_arm_1543] PDF [ref_arm_1494] PDF [ref_arm_1509] PDF [ref_arm_1529] PDF [ref_arm_1562] PDF. Fewer low-reaching, hemispherical examples survive, but these too closely resemble one another [ref_arm_1504] PDF [ref_arm_1528] PDF [ref_arm_1542] PDF [ref_arm_1564] PDF. Comparable groups occur among early Type III helmets: [ref_arm_1348] PDF [ref_arm_1352] PDF [ref_arm_4572] PDF, and [ref_arm_1374] PDF [ref_arm_1400] PDF [ref_arm_1404] PDF [ref_arm_4316] PDF. These similarities suggest that workshops within a region generally worked in a related style. Without figures for production or the number of workshops, however, it is impossible to determine whether individual workshops made particular models in large quantities.

Some form of serial production must have existed in the second half of the fifteenth century in the southern German-speaking lands, northern Italy and Spain. Yet surviving German-language documents suggest that a delivery of thirty-two kettle hats, made by three Augsburg masters in 1485, was among the larger fifteenth-century orders.241 By 1490, patterns were apparently being sent to armourers with commissions,242 suggesting a growing desire to equip groups of soldiers uniformly.

Internal markings may offer further evidence of organised manufacture. Filed grooves [ref_arm_322] PDF or punched dots [ref_arm_425] PDF occur at particular positions along plate edges. On some objects their number increases from plate to plate; on others each component carries the same number [ref_arm_757] PDF [ref_arm_3752] PDF. Sequential marks probably identified the order of assembly. One or two marks on limb or hand protection might distinguish right from left. Such marks also occur on unpaired objects, including breastplates, and often exceed two, making it likely that several similar objects were made together in one workshop.

Giving every component of an object the same number of marks would help keep its parts together before assembly. If dozens of objects were made at once, however, applying and counting that many marks would be cumbersome. Since the number seldom exceeds six, the marks might instead identify sizes or assign components to particular moulds or patterns.

A distinctive group of Type IV breastplates in the Munich Zeughaus may represent early manufacture in quantity.243 According to its catalogue entry, at least one further example formerly belonged to that arsenal and is now in an unidentified private collection [ref_arm_4079] PDF. All use comparatively thin plate. The abdominal plate has a medial ridge and a plain pointed upper edge; the pelvis defence normally consists of three lames. The edges were only lightly deburred by grinding and were not cut after forging. Compared with other surviving Type IV breastplates, their finish is poor, and their dimensions are similar.

Wackernagel’s catalogue provides neither detailed illustrations244 nor descriptions of these plain objects. Mario Scalini suggested manufacture in Munich after an Italian model.245 This is plausible: several breastplates bearing Italian makers’ marks, mostly from Churburg, are very similar, though generally better finished and sometimes decorated with ridges. Two Munich examples appear to follow such decorated models [ref_arm_3653] PDF [ref_arm_3660] PDF. Their construction differs, however. The Munich thoracic and abdominal plates are permanently joined by three rivets; the Italian examples use a central pivoting rivet and internal leather joints at the sides.

Type IV breastplates are usually shallow over the abdomen and require relatively little shaping. The difficult operations are turning the edges and angling the abdominal plate outwards where the pelvis defence attaches. Untrimmed margins survive on the abdominal plate and beneath the arm openings of the thoracic plate. The blanks may have been supplied smaller and then spread to the required dimensions, or delivered in approximately the correct form from the plate hammer. Their splayed, burred edges indicate hot working rather than the armourer’s cold finishing.

The thin Munich plates could have been brought to their final shape cold, with comparatively little force. Repeated heating consumes fuel and causes metal loss through oxidation. Thin plate also loses heat rapidly: substantial cooling occurs between hearth and anvil, and even a red-hot sheet remains at forging temperature for only seconds. Heating the whole workpiece presents another difficulty. Previously finished areas may deform during subsequent hammering or where the tongs grip the hot sheet.

The armourer or supplier probably forged the initial slabs thinner and roughly to the required outline. If another workshop supplied prepared blanks, the armourer may have provided a pattern to control their shape. The burred margins of the pelvis lames likewise show that they were not cut to shape from a larger sheet. The turned edges are simple compared with those of other breastplates, and the lowest pelvis lame has no turn. Such an object could probably be finished quickly. Although its production time with contemporary equipment is difficult to estimate, completion by one worker in eight hours seems a reasonable estimate.

Munich also preserves a substantial group of Type II breastplates from the period.246 Apart from their type, their features resemble those of the Type IV group. Every example has a medial ridge, a feature absent from later Type II arsenal breastplates. Since contemporary depictions rarely show Type II before about 1480, these may have been ordered somewhat later than the Type IV examples, perhaps in the 1480s.

Type II requires more deformation. Although its bowl is shallow, forming it takes greater force than shaping Type IV plates. Conversely, separate thoracic and abdominal plates need not be fitted together. Angling the lower margin and turning the edges remain the most demanding operations. The similarities within the Munich Type IV and Type II groups suggest manufacture in one workshop through an early form of serial production.

At least two sources describe the use of dies in the Innsbruck court armoury. Maximilian I’s “Weiskunig” credits his personal involvement in its technological development:

[…] weiter so hat der weiß kunig in der obgedachten platnerey 



wunderlich harnasch, fur sein kriegsfolckh, zu den kriegsharnasch, ain 



Newe kunst erdacht, das man in seiner platnerey, auf ain mal, dreissig 



vortertail [breastplates], desgleichen hindertail [backplates], 



aufgeformbt hat, dadurch in seiner platnerey, in ainem Jar , ain groß 



Anzal harnasch, fur die landsknecht, die zu fueß gefochtn und gestrittn 



haben, gemacht worden ist, wie wunderlich und kunstlich ist aber dieser 



kunig gewest.
Treitzsaurwein (1775), p. 98. 247

The earliest explicit reference to equipment for serial armour production dates to 5 June 1504, shortly after Konrad Seusenhofer’s appointment as court armourer on 22 January. Maximilian instructed Degen Fuchs, the “Salzmaier” at Hall, to have stamps and anvils made to Seusenhofer’s specifications.248 Initial trials may not yet have succeeded, since 300 breastplates were still ordered from Mühlau in 1506.249 Another order for dies followed in January 1507, addressed to the cannonball smith250 Jörg Zangrer in Absam:

[…] zwei schabutten-ambos zu ruck und armschinen mit ihren kern und 



zugehorung machen, damit Conrad Seusenhofer , sein Hofplattner , alle 



Arbeit, die er zu machen Auftrag habe, ausstempfen könne.
Jahrbuch (1884), Reg. 816. 251

Implementation took several months. In June 1507, acting on Maximilian’s orders, the Innsbruck Raitkammer sent Zangrer’s son Hans to Eisenerz to make:

[…] einen Ambos zu einem modl zu harnaschblech.
Jahrbuch (1883), Reg. 854. 252

The “Schabotte” (French “chabotte”)253 was probably a lower anvil shaped as a negative breastplate mould. The “kern” was most likely its matching core, driven into the mould with the sheet between them [ref_ill_art_5379] PDF. A ram resembling [ref_ill_art_5170] PDF may have operated the dies; water power may have lifted the core.

A document of 1511 records die-forming of breastplates in Innsbruck.254 Seusenhofer’s account of the royal employees and their duties is the most detailed source for this production. Its difficult syntax requires careful interpretation, but it reveals the court armoury’s basic organisation. One group undertook fine work; another made only simple infantry armour. Some armourers evidently worked specified hours at Maximilian’s expense, then received additional payment from Seusenhofer for work outside those hours. The following passage gives production figures:

[…] Die, so krebsen machen, darunder ainer armschin auf die 



fuessknecht machet, so dann ain ganze wochen ist, der ainer in kay. mt. 



zeit vntz zum hertnen vnd ausfeilen 12 krebsen, waz aber ir ainer in 



seiner weil kan machen auf gestempfter krebs, wurdt im von aim krebs 



verdingt zum hertnen 5 krewzer . Michel Lehenher , Hans Wagner , Caspar 



Schuestcr , Utz Gwerlich, Erhard Koch, Lienhard Salzpurger , feyler , 



Cristan Schuestcr , jünger . 7 personen.
Seusenhofer, 1511. 255

Egg read this as six men producing twelve breastplates per week, with the seventh making arm defences.256 That interpretation is almost certainly incorrect. These men specialised in inexpensive rough work; two breastplates per man per week seems implausibly low, especially if dies had already formed the blanks. The remaining tasks were to finish the general shape, perhaps angle the lower edge, and turn the neck and arm margins.

The crucial word is “untz”. If it meant “and”, the named armourers would themselves have filed and hardened the plates. In older German dialects, however, it meant “bis” (“until”), so the likely sense here is “until ready for filing and hardening”. Particularly noteworthy is the implication that even inexpensive stamped infantry breastplates were subsequently hardened.

On this reading, the passage means that one of the seven men made infantry arm defences, while each of the other six prepared twelve breastplates for filing and hardening during a full week of imperial service. Each further die-formed breastplate prepared for hardening outside regular hours earned its maker five Kreuzer. This is an interpretative paraphrase, rather than a literal translation.

A later letter from Seusenhofer in the same year is more explicit:

Vnd mit den raucharbaitern, so in meiner speys sein vnd die krebs vnd 



rugglein machn, halt ich die Ordnung, nemlichn, wann sie ordonari 



arbait gethan vnd feyerabnt haben, so mugen sy krebs machn, vnd wieuil 



sy krebs also nach dem veyerabent machn, so gib ich albeg yedem von 



ainem krebs zu Ion 5 k r . ; aber sy welln yetz etwas mer haben. Mit diser 



Ordnung mag kay. mt. fül krebs in geringer costn gemacht werden vnd 



dise raucharbaitcr machn ain wochen nach dem veyerabent, aine in die 



ander zu raitn, yezuzeitn mynder yezuzeiten mer angeuerlich 18 krebs 



vnd von ainem krebs zu Ion 5 kr . tuet in ainer suma anderhalben guldein 



rh.
Jahrbuch (1884), Reg. 1028. 257

This states that the six workers together finished an average of eighteen additional breastplates per week outside regular hours: three per man. Added to twelve in regular hours, this gives fifteen per man and ninety per week for the group.

Specialists probably undertook the finishing operations. Seusenhofer names grinders and polishers with their respective duties:

Polierer vnnd Schleifer: Caspar Lusch selbander auf der subtil arbait, 



Hans Kessler auf den krebsen, Conz Teininger , schleifer vnd polierer , vnd 



ander arbait zuhelfer . Vier personen.
Seusenhofer’s account, 1511.

A specialist also appears to have forged the pelvis lames and secured breastplate blanks on the stamping anvil:

Balthis Vischer selbander , so die schossen [pelvis-protections] zun 



krebsen schmidt vnd die prust zum einschlagen aufpenst [probably: pin 



down] hat, aber kain wochenlon, sonder waz er teglichs vil oder mer 



verdient. Zwo person.
Seusenhofer’s account, 1511. 258

Balthasar Fischer worked independently of the court armoury and was paid according to daily output rather than receiving a weekly wage. The passage associates two persons with forging pelvis lames and preparing the plates for stamping.

A second letter, written later in 1511, identifies the worker responsible for stamping or die-forming:

[…] Mer Conzen Teiniger , den ich zu aller noturft der platnerei prauch, 



mit krebs einstempfn, aufslagen vnd ander arbait, auch sleyfn, gib ich im 



ain wochen für speys vnd Ion 1 guldein rh.
Jahrbuch (1884), Reg. 1028. 259

The sources therefore establish a division of labour. One man secured the sheet on the anvil, another operated the stamping process, six workers completed the finer hammering and turned the edges, another made pelvis lames, and a further group ground and polished the plates. Who hardened them and attached the pelvis lames and leather straps remains unclear. An output of about ninety breastplates per week in 1511 can reasonably be described as mass production. Surprisingly, the large orders to the Innsbruck court armoury did not continue after Maximilian’s death.260

Early sixteenth-century Type II breastplates survive in substantial numbers in the Vienna arsenal—forty-five examples, including [ref_arm_3421] PDF and [ref_arm_3527] PDF—and Munich, where the total is unknown [ref_arm_3499] PDF [ref_arm_3500] PDF. None has a medial ridge, and their turned edges vary. Some have separate inserted plates at the arm openings [ref_arm_3552] PDF [ref_arm_3551] PDF. A variant with pairs of small holes near the margins occurs both plain [ref_arm_3498] PDF and with decorative bundles of ridges [ref_arm_3473] PDF. Two broadly similar objects belong instead to Type III [ref_arm_3526] PDF [ref_arm_3567] PDF.

All have cut-outs at the narrowing waist, perhaps to retain a belt, accommodate different bodies or simplify manufacture. Many lack ridge decoration, and their pelvis lames use simple pivoting rivet joints. Plate thickness is generally below 2.00 mm. These features identify inexpensive equipment for ordinary soldiers. Contemporary depictions place the fashion in the first two decades of the sixteenth century, making manufacture by the documented die-forming process plausible.

Maximilian ordered large numbers of breastplates throughout his reign. In 1495 he commissioned 1,000 from Nuremberg. The city council replied on 12 May that 300 were in stock and the remainder could not be delivered before 7 June.261 Thus 700 could apparently be made, or at least procured, in about a month. Such rapid supply would have required methods including division of labour. Some surviving Vienna breastplates may derive from these orders and have entered the arsenal later. Several bear Nuremberg marks; unmarked examples cannot be assigned securely.

It has been suggested that the Vienna Type II group was made around 1508, chiefly for Maximilian, who wanted uniformly equipped troops for his planned journey to Rome for coronation as emperor. The development of stamping was most probably connected with this undertaking. Seeking independence from the powerful councils of imperial cities, he attempted to establish mass production in Innsbruck, his favoured city in the hereditary lands. Its output apparently remained insufficient: in 1508 he still ordered 2,000 breastplates from Nuremberg.262

Whether armourers elsewhere also used dies, then or later, has not yet been systematically investigated. Nuremberg, Augsburg and Landshut required approved armour to bear the city’s arms, making attribution of the many unmarked Vienna breastplates to those centres less likely. Innsbruck imposed no such requirement, so it remains a possible origin.

The orders also mention dies for arm defences. Which surviving objects might have been made with them? A particularly simple group, evidently intended for infantry, has crude hand plates attached directly to the forearm defence by a single rivet travelling in a slot [ref_arm_5027] PDF [ref_arm_4926] PDF. Its earliest known depiction is in the Marienkirche at Reutlingen [ref_ill_art_5360] PDF. Only the forearm slot and a rivet head at its upper end are visible; the hand lames appear able to slide inside when not required. Such defences are rarely depicted but were in use around 1500. Several associated elbow defences carry Nuremberg approval marks [ref_arm_263] PDF [ref_arm_275] PDF.

These objects and the documentary evidence stand at the end of the period studied here. The preceding discussion nevertheless suggests that serial or mass-production methods developed well before the sixteenth century. Many questions remain unresolved.

Redaktionelle Hinweise · 3
  • Die Interpretation von „untz“ und die daraus abgeleiteten 90 Brustplatten pro Woche bleiben die Argumentation der Dissertation, keine neu geprüfte Produktionsstatistik.
  • „selbander … Zwo person“ steht im Originalkommentar neben „Two people are working for him“. Die Neubearbeitung legt die Zahl der zusätzlich Beschäftigten nicht fest; Wortlaut und Zählung fachlich prüfen.
  • Historische deutschsprachige Zitate unverändert übernommen; eckige englische Erläuterungen stammen bereits aus der Dissertation. Die Paraphrase der Produktionsabrechnung ist ausdrücklich als Deutung gekennzeichnet.
Originalwortlaut vergleichen
4.4.5 Central Europe 



Extant early armour of Italian style is indeed often very similar. It is surp rising that already 



by the end of the 14 th century helmets of type-IV – the earliest type of armour to survive in 



larger quantities – often resemble each other very closely. Especially the model with the 



pointed skull is extant in several, almost identical examples [ref_arm_1495] [ref_arm_1543] 



[ref_arm_1494] [ ref_arm_1509] [ ref_arm_1529] [ ref_arm_1562]. Though preserved in 



smaller numbers, several low -reaching type-IV models with a hemispherical skull are just 



as well similar to each other [ ref_arm_1504] [ ref_arm_1528] [ ref_arm_1542] 



[ref_arm_1564]. Also some early helmets of type -III have very close similarities 



([ref_arm_1348] [ ref_arm_1352] [ ref_arm_4572]) ([ ref_arm_1374] [ ref_arm_1400] 



[ref_arm_1404] [ref_arm_4316]) . These similarities suggest that most of the workshops of 



one region produced armour in a related style. As no total numbers, neither of production 



quantities nor of contemporary workshops, do exist, it is impo ssible to tell if a single 



workshop produced single models in the same style and in huge numbers.  



In the second half of the 15 th century, some ways of an serial -like production must have 



existed – in the south of the German speaking lands as well as in northern Italy and in Spain. 



Nevertheless, for the German speaking lands according to the remaining documents it seems 



like a delivery of 32 iron -hats made in Augsburg by three different masters in 1485 241 was 



one of the larger orders in the 15 th century. Documents suggest that by 1490 patterns were 



sent to the armourers when armour was ordered.242 Obviously the desire for a more uniform 



appearance of a group of soldier’s was increasing. 



One indicator for the production of armour in some kind of manufacture - or fabric-process 



can be found at the interior of some armour parts. Such objects are interiorly marked at a 



certain location along an edge by either a number of groove-like filings [ref_arm_322] or by 



punched dots [ref_arm_425]. While at some objects the marks are counting in numbers, at 



others the numbers of marks are the same at each segment of the item [ ref_arm_757] 



[ref_arm_3752]. In the first case the marks are very likely only meant to help the armourer 



identifying the right mounting-order of the single pieces. Whenever markings counting only 



till 2 would have been found at armour for the limbs or the hands, it is possible that this was



meant to separate between the right and the left si de of the body. As such marks are often 



found at non paired armour parts like breastplates and as they often count higher numbers, 



it is very likely that several almost identical objects were made at the same time in one 



workshop. Assuming that tens of ite ms of one kind were made, it would be too time -



consuming to add and later to count all the necessary marks to each segment. All segments 



of one item before mounting got the same number of marks. As the marks usually do not 



count to more than 6, it is also possible that the numbers describe the size of a serial produced 



armour part. It is also possible that different molds or patterns existed and the markings 



mapped the segments to one model. 



A group of early items, probably produced in huge quantities, is a special variation of type-



IV breastplates, preserved in the “Zeughaus” in Munich243. At least one plate – according to 



the catalogue description – is coming from the Zeughaus inventory but is now in anonymous 



private hands [ref_arm_4079]. They all are made of comparatively thin plate. The abdomen-



plate has a medial ridge and its upper edge ends in a plain point. Usually the pelvis consists 



of three lames. All edges are only slightly de-burred by grinding and had not been cut after 



forging. Obviously the plates are of low quality, compared to other extant examples of type-



IV . All plates have similar dimensions. In the Wackernagel’s catalogue on the Zeughaus no 



detailed image244 or description of the simple plates  is published. Mario Scalini suggested 



that they are all of Munich production after an Italian model. 245 This is indeed possible, as 



several plates with Italian maker’s marks – most of the from the Churburg armoury – are 



very similar, but usually of better quality and some of them are decorated by ridges. Two of 



the Munich plates indeed seem to resemble such decorated Italian models [ ref_arm_3653] 



[ref_arm_3660]. Nevertheless, the construction of the Munich breastplates is different: The 



abdomen and the thorax -plates are permanently connected via 3 rivets, whereas the Italian 



Models have a central pivoting rivet and at each side an interior leather-joint. 



Breastplates of type-IV are usually not very deep at the belly. The plates need to be shaped 



only slightly. The difficult parts are the turning of the edges and the outward angling of the 



abdomen-plate, where the pelvis is attached. Uncut edges are visible at the abdomen and the 



thorax-plates under the arm cutouts. It is likely that the pattern for the plates had been 



supplied smaller and was widened out into the desired dimensions. A second possibility is 



that they were already delivered in the right format from the plate-hammer. The burred edges 



do certainly not derive from the cold work of the armourer, the metal is splayed in a way that 



can only be achieved by working it hot. The thin plates used for the Munich breastplates did 



not have to be heated and could be hammered without much mechanical force into the final 



shape. For a metalworker it is always better to avoid the repeated heating of the material, as 



it is fuel consuming and the metal “burns off” within time. Additionally, the thin plates do 



not keep the heat for very long. While taking them red hot from the hearth or to the oven and 



placing them on an anvil or some other support, they already cool significantly. Even if they 



are still red hot when the first blows of the hammer hit the plate, within a fe w seconds the 



plate will cool down and cannot be forged anymore. It is also very difficult to heat the whole 



work-piece in the oven, as this leads to an all-over red hot temperature. When the plates are 



subsequently taken off for hammering, the already fin ished shapes from the preceding run



are easily deformed again by the following hammering. Also where the grippers hold the red 



hot plate it gets easily deformed.  



The armourer or the plate -supplier probably forged the starting -slabs thinner and roughly 



into the necessary format. The control of the correct shaping would have been difficult for 



the armourer if the single plates were ordered ready -made from another workshop. 



Therefore, he might have given a pattern to the plate -hammer. As the lames for the pel vis 



are also left burred, it is obvious that the plates were not cut from a larger plate into their 



final shape. Compared to other breastplates, the turned edges are also of rather simple make. 



The lowest pelvis-lame has no turn at all. Such a breastplate was certainly finished within a 



short time. While it is of course difficult to estimate how long it actually took with the 



technical equipment of the time, it is certainly not wrong to say that one worker could finish 



such a plate within eight working hours.  



Also in Munich another large group of breastplates of the considered period is stored 246. 



They are of type -II, but all other features are similar to those of the Munich type -IV 



breastplates described above. All examples have a medial ridge – a feature not found on later 



type-II arsenal breastplates anymore. As contemporary depictions before 1480 ca. do usually 



not show breastplates of type-II, it is possible that the said ones were ordered for the Munich 



Zeughaus a little later than the type -IV examples, maybe in the 1480ies. For this type of 



breastplate already more deformation work is necessary. The plates are only slightly deep -



drawn, but the deep-drawing of the plate requires more mechanical force than the making of 



breastplates of type-IV . On the other hand, no adjustment of the thorax and abdomen-plates 



for the mounting is necessary. Also here the toughest part is the angling of the lower edge 



and the turning of the edges. As the type-IV and -II plates of the Munich “Zeughaus” are all 



similar, it is l ikely that they were made in one workshop by some kind of early serial 



manufacture. 



There are actually at least two sources that tell about the use of dies in the court-armoury at 



Innsbruck. One is found in Maximilian I.’s “Weiskunig”, where his personal engagement in 



the technological development of his court-armoury at Innsbruck is described:  



[…] weiter so hat der weiß kunig in der obgedachten platnerey 



wunderlich harnasch, fur sein kriegsfolckh, zu den kriegsharnasch, ain 



Newe kunst erdacht, das man in seiner platnerey, auf ain mal, dreissig 



vortertail [breastplates], desgleichen hindertail [backplates], 



aufgeformbt hat, dadurch in seiner platnerey, in ainem Jar , ain groß 



Anzal harnasch, fur die landsknecht, die zu fueß gefochtn und gestrittn 



haben, gemacht worden ist, wie wunderlich und kunstlich ist aber dieser 



kunig gewest.247



The earliest note that clearly refers to techniques for the serial production of armour dates 



from the 5 th of June 1504, just shortly after Maximilian had made Konrad Seusenhofer his 



court-armourer in Innsbruck (22 nd of January). King Maximilian I. gives order to the 



„Salzmaier“ in Hall, Degen Fuchs, to have stampers and anvils made after the instructions 



of Konrad Seusenhofer.248 It is possible that tests with stamping were not successful yet, as 



large numbers of breastplates (300) were actually still ordered from Mühlau in 1506.249 One 



year later the sources refer again to the order of dies. In a document of Janu ary 1507 King 



Maximilian orders from his bullet-smith250 in Absam, Jörg- Zangrer:  



[…] zwei schabutten-ambos zu ruck und armschinen mit ihren kern und 



zugehorung machen, damit Conrad Seusenhofer , sein Hofplattner , alle 



Arbeit, die er zu machen Auftrag habe, ausstempfen könne.251 



It took some months until Maximilian’s order was realized. In June 1507, on the order of 



King Maximilian, the Raitkammer in Innsbruck had actually sent the son of Jörg Zangrer, 



Hans Zangrer, to the city of Eisenerz for making: 



[…] einen Ambos zu einem modl zu harnaschblech.252  



The “Schabotte” (Fr. chabotte) 253 mentioned above was probably the lower anvil, shaped 



like a negative mold of the breastplate, the “kern” is most likely the exactly corresponding 



core that is stamped into the “Schabo tte” while the plate is placed in between 



[ref_ill_art_5379]. The molds might have been operated by a ram similar to 



[ref_ill_art_5170]. It is also possible that the core was lifted with the help of waterpower.  



A document of 1511 254 proofes that in Innsbruck breastplates were actually deep -drawn. 



Here Seusenhofer accounts for the King’s employees and their work in his court -armoury. 



This is certainly the most detailed source on the serial -production of breastplates. The text 



is difficult to understand as the syntax is interlaced, but a considerate reading reveals the 



basic facts that allow the understanding of the organization of the Innsbruck court-armoury.  



The workers were split in groups. The first group made the subtle work. The second one 



produced exclusively the simple foot soldier’s armour. Obviously some armourers had to 



work certain hours on the account of Emperor Maximillian I., but after work they were paid 



on Seusenhofer’s account. The following paragraphs tell details about the numbers of simple 



breastplates produced in a certain time:



[…] Die, so krebsen machen, darunder ainer armschin auf die 



fuessknecht machet, so dann ain ganze wochen ist, der ainer in kay. mt. 



zeit vntz zum hertnen vnd ausfeilen 12 krebsen, waz aber ir ainer in 



seiner weil kan machen auf gestempfter krebs, wurdt im von aim krebs 



verdingt zum hertnen 5 krewzer . Michel Lehenher , Hans Wagner , Caspar 



Schuestcr , Utz Gwerlich, Erhard Koch, Lienhard Salzpurger , feyler , 



Cristan Schuestcr , jünger . 7 personen.255 



Egg256 understood from this source that 6 workers – the named 7th man made arm-defenses 



– finished a total of 12 breastplates a week. This is certa inly incorrect. These men were 



working on the cheap „rough“ parts only. The average of 2 finished items a week is far too 



low for one specialized worker, especially if the rough shape of the breastplates was indeed 



formed with the help of dies. The armoure r only had to finish the general shape, maybe to 



angle the lower edge, to turn the edges at neck-and arm-cutouts.  



The most unclear word in the aforesaid paragraph is “untz”. It is important, if it means “and”, 



the named armourers themselves “filed and hardened” the plates. In older German dialects 



this word meant “bis” (Engl. until) and therefore it is very likely that in the concerned source 



it can be read as “until ready for” (filing and hardening). Here it is especially noteworthy 



that even the cheap footsoldiers’s “stamped” breastplates later obviously got hardened. 



If the interpretation is correct, in modern words the text would sound: “Within the group of 



the seven following workers, one makes arm defenses for the foot soldiers. Each of the other 



six workers finishes 12 breastplates – until ready for filing and hardening – within one week 



of his regular service to his Imperial Highness. For each further deep -drawn breastplate he 



finishes for hardening after his regular working-time, he is paid 5 Kreuzer.  



A letter concerned with the same topic written later in the same year by Seusenhofer is even 



more precise:



Vnd mit den raucharbaitern, so in meiner speys sein vnd die krebs vnd 



rugglein machn, halt ich die Ordnung, nemlichn, wann sie ordonari 



arbait gethan vnd feyerabnt haben, so mugen sy krebs machn, vnd wieuil 



sy krebs also nach dem veyerabent machn, so gib ich albeg yedem von 



ainem krebs zu Ion 5 k r . ; aber sy welln yetz etwas mer haben. Mit diser 



Ordnung mag kay. mt. fül krebs in geringer costn gemacht werden vnd 



dise raucharbaitcr machn ain wochen nach dem veyerabent, aine in die 



ander zu raitn, yezuzeitn mynder yezuzeiten mer angeuerlich 18 krebs 



vnd von ainem krebs zu Ion 5 kr . tuet in ainer suma anderhalben guldein 



rh.257 



This text clearly says that in average the 6 workers after the regular working -time together 



finished 18 additional breastplates a week – hence 3 breastplates were made by one man. 



Together with the 12 breastplates made in his regular working time, one man made 15 and 



therefore all the workers together made a total of 90 breastplates a week.  



It is very likely that specialized workers finished the breastplates mentioned above. In the 



accounts of Seusenhofer grinders and polisher are named together with their specializations: 



Polierer vnnd Schleifer: Caspar Lusch selbander auf der subtil arbait, 



Hans Kessler auf den krebsen, Conz Teininger , schleifer vnd polierer , vnd 



ander arbait zuhelfer . Vier personen. 



Also the pelvis-lames for the breastplates were obviously made by a specialized worker who 



furthermore had to pin down the breastplates on the anvil for stamping: 



Balthis Vischer selbander , so die schossen [pelvis-protections] zun 



krebsen schmidt vnd die prust zum einschlagen aufpenst [probably: pin 



down] hat, aber kain wochenlon, sonder waz er teglichs vil oder mer 



verdient. Zwo person.258 



This Balthasar Fischer is working independently from the court -armoury. He is paid only 



according to the daily work-quantity. Two people are working for him. They are forging the 



pelvis-lames and they are preparing the plates on the stamping anvil. 



A little later in 1511 a second letter of Seusenhofer tells that a specialized worker was 



responsible for the stamping or deep-drawing itself:



[…] Mer Conzen Teiniger , den ich zu aller noturft der platnerei prauch, 



mit krebs einstempfn, aufslagen vnd ander arbait, auch sleyfn, gib ich im 



ain wochen für speys vnd Ion 1 guldein rh.259 



In summary, the breastplates were therefore certainly made by division of labor processes. 



One man pinned down the plate on the anvil. A second one operated the stamping process; a 



group of six workers made the fine hammer -work and turned the edges. Another worker 



made the pelvis -lames and a group of people were grinding and polishing the plates. It is 



nevertheless not clear wh o hardened and who mounted the pelvis -lames and the leather -



straps. The weekly output of ca. 90 breastplates in the year 1511 can certainly be defined as 



“mass-production”. It is surprising that the large breastplates orders addressed to the 



Innsbruck court-armoury are not continuing after Maximilian’s death.260  



Several type-II breastplates of the early 16 th century are preserved in large numbers in the 



Vienna (45 items, e. g. [ ref_arm_3421] [ ref_arm_3527]) and the Munich Zeughaus 



(unknown number, e. g. [ref_arm_3499] [ref_arm_3500]). They all have no medial ridge and 



the turned edges can be of different types. At some objects, the arm cutouts are made of a 



separate, inserted plate [ ref_arm_3552] [ref_arm_3551]. One variation with pairs of small 



holes drilled close to the edges exists in two versions: One is plane [ ref_arm_3498] and the 



other one is decorated by a bundle of ridges [ ref_arm_3473]. Two, in general similar items 



[ref_arm_3526] [ref_arm_3567], are actually of type-III. 



All of these breastplates have cutouts at the tapering of the waist. They were either applied 



to hold the belt in place, to make the plate fit to different trunks or to facilitate the production. 



Many of them show no ridge decoration and the pelvis -lames are attached via the easy -to-



make pivoting rivet-joint. The plate-thickness is usually below 2.00 mm. All these facts mark 



these breastplates as cheap equipment for simple soldiers. According to contemporary 



artworks, they were in fashion in the first two decades of the 16th century and therefore they 



could well have been made in the deep -drawing technique described by the aforesaid 



contemporary sources. 



Maximilian I. throughout his reign had ordered huge quantities of breastplates. One of the 



earliest evident mass -order in 1495 addr essed the Nuremberg armourer’s to deliver 1000 



breastplates. The city council answered in a letter to Maximilian on 12 th of May that 300 



items are in stock and that the other could not be delivered before the 7 th of June. 261 This 



would mean that within about a month 700 breastplates could be produced or at least bought 



in. Such scores could certainly only be reached in a short time by serial-production methods 



like the division of labor. It is well possible that some of the extant Vienna breastplates were 



part of one of these mass-orders and later they came to the arsenal. Some of them even bear 



Nuremberg marks. Those that have no marks might have been made anywhere. It has already 



been suggested that the aforesaid type -II breastplates in Vienna were made abo ut 1508, 



mainly for King Maximilian I. He wanted to have his troops equipped uniformly on his ride 



to his planned coronation as Roman Emperor in the Eternal City. The development of the 



stamping-technique is most likely connected to this event. Maximilian wanted to be



independent in his orders from the influential councils of the imperial towns and therefore 



he tried to establish the mass -production of armour in Innsbruck – his beloved city in his 



own hereditary lands. It seems like the output of the Innsbruck workshops was not sufficient, 



as Maximilian in 1508 still had to order 2000 breastplates from Nuremberg.262 



It has not been scientifically examined so far if dies were actually used in the making of 



armour in other cities than Innsbruck and possibly also in later times. As the city councils of 



Nuremberg, Augsburg and Landshut had ordered to stamp the good quality items with the 



city’s coat of arms, there is only little chance that the many unmarked breastplates of the 



Vienna Zeughaus were made in one of t hese cities. Only Innsbruck never had ordered the 



quality-stamping of armour produced in the city and therefore it is possible that the 



unmarked items were made in Innsbruck. 



As also dies for the stamping of arm defenses are mentioned, the question can be asked, 



which extant items could be produced in this technique. A special type of extant arm defenses 



is made so simple that it was certainly made only for foot soldiers. The specialty of this 



armour is that the lower arm -protections have crude plates for t he protection of the hand 



directly attached. They are fixed by one single rivet, sliding in a slot [ ref_arm_5027] 



[ref_arm_4926]. The earliest depiction of such a defense is found in the Marienkirche in 



Reutlingen [ref_ill_art_5360]. Only the slot at the lower arm and a rivet head at its upper 



end are visible. It seems like the hand -lames cou ld be slide interiorly when not in use. 



Generally, these defenses are not depicted very often. They were in use around 1500. Several 



of the elbow defenses bear the quality approval mark of Nuremberg [ ref_arm_263] 



[ref_arm_275]. The mentioned objects and the sources for the serial-production technologies 



do of course mark the very end of the considered period. The preceding discussion of the 



topic of serial -or mass-production of armour shows that such processes were most likely 



developed long before the 16th century – but by far not all questions are answered.

5 Supplying crafts

S. 160 · Sprachlich überarbeitet · Entwurf

5 Supplying crafts

Armour manufacture depended on products supplied by several specialist crafts. Plate-making and nail-making have already been discussed in detail. This chapter briefly surveys other supporting trades whose work lay outside the armourer’s principal specialisation.

Originalwortlaut vergleichen
5 Supplying crafts 



To produce armour, different specialized supplying crafts or arts had to deliver their products 



to the armourer’s workshop. Some of them, like the making of plates or the making of nails, 



were already described above in details. In the following chapter, some further supplying 



craft-branches not belonging to those of the armourer’s specializ ation will be shortly 



summarized.
S. 160 · Sprachlich überarbeitet · Entwurf

5.1 Wire drawing

Many turned edges contain wire. Rolling the sheet around it helps produce an even, rounded edge and prevents the turn from being flattened accidentally during hammering. Armourers could have made this wire themselves, but probably obtained it from specialist suppliers.

Wire drawing was known in antiquity. Wire can also be forged, but the thinner and longer it becomes, the more difficult and time-consuming forging is. Wire served many purposes, with ring-armour makers creating substantial demand. Since ring-armour panels often protected areas exposed between plates, this provided another connection between wire production and plate-armour manufacture.

The starting material was first forged into a long strip with a section at least 5 mm across; strips could also be cut from sheet. One end was pointed to pass through a conical hole in a drawplate. At its narrow end, the hole was 8–15% smaller than the strip’s diameter. Tongs gripped the projecting point and pulled the strip through by force.

Several methods were available. In the simplest, the worker supplied the force, either standing on the drawplate or sitting on a swing in front of a drawplate fixed to a heavy wooden support [ref_ill_art_5324] PDF. A hand-cranked winch could also be used [ref_ill_art_5362] PDF (description 1). The considerable effort required, especially at initial diameters of perhaps 4–5 mm, made these methods unsuitable for large-scale output. They were better suited to drawing finer wire from partly finished stock.

Experiments in Nuremberg around 1402–1415 gave the production of this stock an important impetus.263 A local entrepreneur financed systematic development of water-powered wire drawing. Albrecht Dürer depicted the celebrated “Sandmühle” wire mill [ref_ill_art_5349] PDF. Its fifteenth-century machinery is poorly understood, but probably operated on principles similar to those illustrated in Biringuccio’s “pirotechnia” of 1540 [ref_ill_art_5362] PDF (description 2).

In that illustration, a waterwheel drives a horizontal crankshaft connected by a leather belt and rope to a ring around the arms of a pair of tongs. Seated on a swing, the worker guides the tongs by hand and grips the wire emerging from the drawplate at the forward limit of his movement. The shaft’s backward pull closes the jaws and draws the wire through. At the rear limit, the worker releases the wire and swings forward again. This cycle repeats continuously.

Originalwortlaut vergleichen
5.1 Wire drawing 



Inside many turned edges a wire is inserted. The armourers rolled the plate around this wire 



to make sure that the edge would have a uniform, round appearance and would not accidently 



become flat by hammering. The armourer of course might have made this wire himself, but 



rather likely he obtained it from a specialized supplier.  



The technique of drawing wire was known since antiquity. It is generally possible to forge a 



wire, but the thinner its diameter should  be, and the longer its dimensions are the more 



difficult and time -demanding this work would become. Wire was needed for different 



purpose; a huge demand came from the ring -armour makers. As segments of such armour 



were often attached to exposed locations of plate armour, the production of wire is connected 



to armour making by even one further aspect.  



The starting material for wire-drawing first had to be forged to a longer stripe with a diameter 



of at least 5 mm. Also the cutting of a plate into smaller stripes is possible. One end of these 



stripes had to be pointed to fit through a cone shaped hole in a draw plate that at the narrow 



side was 8-15% smaller than the diameter of the stripe. After sticking this end through the 



hole it was grabbed by a tong and the stripe was drawn with force through the hole. Different 



techniques for wire drawing can be adopted. The simplest one was operated by manpower. 



The worker was either standing on the drawplate, or the latter was fixed to a heavy wooden 



base and the worker is sitting on a swing [ref_ill_art_5324]. Also a winch with a crank handle 



could be used [ ref_ill_art_5362] (descr. 1). These techniques were unsuitable for a mass 



production of wire, due to the need for immense manpower, especially in the beginning of 



the process which starts from diameters of maybe 4 -5 mm. Such methods were rather 



suitable for the production of finer wires by drawing semi-finished products. The technology 



for the drawing of the latter got an important impulse by experiments carried out in 



Nuremberg around 1402 to 1415 263. A local entrepreneur funded the systematical 



development of drawing wire by means of a waterpowered mill. Albrecht Dürer painted the 



famous wire-drawing “Sandmühle” in Nuremberg [ref_ill_art_5349]. The details of the new 



technique are for the 15 th century obscure, but it is likely that it was basically the same like 



illustrated in Biringuccio’s “pirotechnia” in 1540 [ref_ill_art_5362] (descr. 2). Here a water 



wheel operates a horizontal crankshaft. This is connected to a leather belt and a rope which 



ends in a ring put over the arms of a tong. A worker is sitting on a swing and controls the 



tongue with his hands. He grabs the wire which is lead through the draw plate in front of 



him exactly in the moment when he is the closest to the plate. The waterpowered shaft then 



by drawing backwards closes the chops of the tong holding the wire tight and pulling it 



through the draw plate. When in the most distant position to the draw plate the worker would 



release the wire and move forward with his swing again. This swinging process is repeated 



permanently.
S. 161 · Sprachlich überarbeitet · Entwurf

5.2 Toolmaking

Specialist toolmakers supplied hammers, files, sheet-metal shears, anvils, stakes, saws and drills. Hammers and stakes were among the simplest tools and might have been made by armourers themselves; the others demanded more specialised skills. Shears required excellent material to cut steel plate up to 6 mm thick. Anvils were often forged from a heavy iron block rather than cast, requiring powerful hammers and supports for handling the workpiece. Files for finishing pierced decoration also had to be of high quality.

Punch cutters supplied marking tools. Symbols or letters were cut in reverse into steel punches with small gravers and chisels, after which the punches were hardened and tempered. Relatively simple decorative punches were already used in the late fourteenth century. Armourers may have made some themselves, but probably commissioned most from the same “Stempfelgraber” who supplied makers’, civic and owners’ marking punches. These specialists probably also made coin punches. Iron-cutting techniques developed throughout the fifteenth century and reached a high level in the sixteenth-century decoration of sword and rapier hilts.

Originalwortlaut vergleichen
5.2 Production of tools  



Hammers, files, plate shears, anvils, stakes, saws, drills etc. had to be produced by 



specialized toolmakers. While ham mers and stakes are probably the most simple of the 



mentioned tools and thus could have been made by the armourer himself, all other items 



required certain sophisticated skills. Plate shears had to be made of the best material, so they 



were able to cut up to 6 mm of steel plate. Anvils are often made of one heavy block of iron. 



They were usually not cast but forged, which required heavy hammers and supports for the 



handling of the work piece. The files necessary for finishing the fretwork on some armour 



needed to be made of very good quality.  



Punch cutters needed to provide certain tools to the armourer’s workshop. The mark-stamps 



needed to be cut into a steel chisel which subsequently was hardened and tempered. The 



symbols or letters have to be cut into th e steel in reverse by means of small gravers and 



chisels. But also for decoration, rather simple punches were already used in the late 14 th 



century. These might have been made by the armourers themselves, but most likely they 



were ordered from the same cra ftsman who supplied the punches for armourer’s, city’s or 



owner’s marks, the so called “Stempfelgraber”. These specialized workers were probably 



also making the punches for coins. The techniques for cutting iron were increasingly 



developing throughout the 15th and reached a height in the 16 th century with the decoration 



of sword and rapier hilts.
S. 161 · Sprachlich überarbeitet · Entwurf

5.3 Tailoring

For made-to-measure armour, the lining had to fit both the plates and the wearer. Linings for inexpensive standardised armour were presumably made to standard patterns. A helmet lining intended to cushion blows and improve comfort required padding in the appropriate places. Two fabric layers could enclose wool, hay, straw or horsehair, with quilting to hold the filling in position. Whether armourers sewed the linings themselves is unclear. They may have worked with tailors who supplied and fitted the textile components [ref_ill_art_5319] PDF [ref_ill_art_5320] PDF.

Originalwortlaut vergleichen
5.3 Tailoring  



For armour made to measure it was necessary to fit the lining to both, the armour and the 



wearer’s body. The linings of cheaper mass produced and standardized armour were certainly 



made after standardized patterns. If a helmet was meant to be bolstered for comfort and 



against hits and blows, a specialist needed to pad a lining at the right spots. This also meant 



that it had to consist of two layers of fabric which could be stuffed with wool, hay, straw or 



horse hair. A stitching was in the end added to keep the filling in place. It is not clear if the 



sewing of the linings was carried out by the armourers. Possibly they worked together with 



tailors who fi tted the armour with the necessary fabric parts [ ref_ill_art_5319] 



[ref_ill_art_5320].
S. 161–162 · Sprachlich überarbeitet · Entwurf

5.4 Etching

Corrosive liquids can form decorative patterns in iron or steel. In the sixteenth century, etching was widely used both on arms and armour and on printing plates. The “liber illuministarum” records several simple fifteenth-century recipes for etching steel.264 One directs the corrosive liquid to be applied to the iron with a feather. In the others, an acid-resistant coating covers the surface except where the ornament is to appear. The liquid is then applied to the exposed areas with a brush, a sheet or a feather. The principal difference from the modern method described here is that the latter usually coats the whole surface first, then removes the resist along the intended design.

On a blued surface, a weak acid can remove the blue layer to create a pattern. Deeper etching can instead produce dark ornament contrasting with the bright polished metal. The liquid’s strength and the exposure time determine depth and definition. An excessively strong solution may continue attacking the iron despite washing, leaving ragged contours.

These techniques were very probably used on armour from the second half of the fifteenth century: surviving objects include both blue-etched [ref_arm_1971] PDF and deeply etched decoration [ref_arm_3736] PDF.

Redaktionelle Hinweise · 1
  • „a sheet“ als Auftragshilfe ist im Original unklar und bleibt bis zur Rezeptprüfung unspezifiziert.
Originalwortlaut vergleichen
5.4 Etching 



Decorative patterns can be drawn by corrosive liquids into the surface of iron or steel. This 



technique is very widespread in the 16th century and is employed not only for the decoration 



of arms and armour, but also for etching illustrations on printing plates. The “liber 



illuministarum” mentions several simple 15th century recipes on how to etch on steel264. For 



one technique the corrosive liquid is painted directly on the iron by a feather. For all other 



recipes the surface is covered with an acid resistant coating, while the locat ions where the 



ornaments should appear later were left blank. In these areas the corrosive liquid is applied 



by means of a brush, a sheet or a feather. The main difference to modern etching is that today 



usually all the surface is coated with a resistant p aint and then this layer is taken off where 



the decoration should appear.  



Into the surface of an artifact blued in the technique mentioned above a pattern can be drawn 



by etching off the blue layer with a weak acid. But ornaments can also be etched deep i nto 



the surface, with their dark color giving a strong contrast to the silver shiny polished surface. 



The strength of the corrosive liquid and the time of exposure are the factors which decide 



about the depth and clarity of the etching. A too strong liquid might go on reacting with the



iron even though attempts had been made to wash it off and thus the contours of the etching 



might look fringy.  



It is very likely that such techniques from the second half of the 15 th century on were also 



used for decorating armour, as indeed a few objects of the time are decorated by blue - 



[ref_arm_1971] and others by deep-etching [ref_arm_3736].
S. 162 · Sprachlich überarbeitet · Entwurf

5.5 Bellows

Air must be supplied to a charcoal fire to reach the temperatures required for forging and heat treatment; the source gives 723 °C in connection with steel hardening. Bellows were used for this purpose from the High Middle Ages. High, stable temperatures require a steady airflow. A single-chamber bellows interrupts that flow while refilling, so two bellows were used together.

At sites where metal was melted or heavy iron billets worked, water power could operate the bellows continuously. Armourers needed them only intermittently, for example when turning tightly curved edges or raising helmets. Water power was therefore unnecessary for this purpose in their workshops. The bellows were probably operated by a handle, as depicted in [ref_ill_art_5330] PDF (description 3).

Redaktionelle Hinweise · 1
  • Die pauschale Angabe von 723 °C als Härtetemperatur ist fachlich zu prüfen. Zahl erhalten, aber ausdrücklich als Quellenangabe kenntlich gemacht; keine neue allgemeingültige Prozessvorgabe.
Originalwortlaut vergleichen
5.5 Bellows 



To reach the heat that is required in a smith’s hearth, for example for hardening steel 723 C, 



it is necessary to bring air into the burning charcoal fire. For this purpose, since the high 



Middle Ages bellows were used. To achieve high and permanent temper atures it is very 



important to keep the air steadily floating in a regular stream. A single chamber bellow 



cannot provide this demand, as its work-cycle is interrupted by the refilling of the chamber. 



The solution was found in using two bellows. At product ion sites where metal was melted 



or where heavy iron billets were treated mechanically, water power could be used to 



permanently operate the bellows. In the armourers workshop they were needed only 



occasionally, for example for turning narrow curved edges or for raising helmets. Therefore, 



it was not necessary to use water power for the bellows. They were most likely operated by 



a handle, as can be seen at artwork [ref_ill_art_5330] (descr. 3).
S. 162 · Sprachlich überarbeitet · Entwurf

5.6 Tanning

Tanning was another specialist trade [ref_ill_art_5315] PDF [ref_ill_art_5317] PDF. Different hides and furs were processed for different purposes. Armourers needed leather particularly for fastenings and joints. Because surviving leather cannot always be securely dated to an object’s manufacture, the kinds originally used remain uncertain.

Nuremberg armourers’ regulations required buckskin for the gloves inside hand defences,265 and a few surviving gloves use this material. It is generally chamois-tanned: the raw skin is repeatedly kneaded with fish oil, then heated to about 40 °C. The grain side is often abraded to remove scars and minor imperfections.266 The resulting leather is yellow and very soft. Deer, sheep and goat skins are also processed in this way; such leather remains familiar as window-cleaning material.

Soft buckskin was preferred for expensive armour and joints requiring considerable flexibility. Less costly objects were probably fitted with cowhide straps.

Originalwortlaut vergleichen
5.6 Tanners 



Tanning of animal skin was a specialized craft as well [ref_ill_art_5315] [ref_ill_art_5317]. 



Many different kinds of skins and fur were tanned for different purpose. For the making of 



armour, leather was important for the fastening of the single pieces. As it cannot be said with 



certainty that the remains of leather to be found on extant armour pieces are cont emporary 



with the armour -production time, it remains questionable which kind of leather the 



armourers used. The bylaws of the armourers of Nuremberg required the use of buckskin for 



the gloves inside the hand -protections265. Also few remaining leather gloves  are made of 



such material. It is usually tanned in the chamois method. This is the repeated kneading of 



the raw skin together with fish oil and its subsequent heating at about 40 0C. Often the grain 



side of the skin is grounded so injuries or other small imperfections would disappear.266 The 



leather tanned by this method has a yellow color and is very soft. Also other animal skin like 



deer, sheep and goat skin is often tanned in the chamois method. It is still used today for 



cleaning window glass. The soft b uckskin was favored for the expensive armour and for 



joints which need to allow a high flexibility. Cheaper armour was most likely equipped with 



cow-skin stripes.
S. 162–163 · Sprachlich überarbeitet · Entwurf

5.7 Lace-making

By the late fourteenth century, contemporary depictions of clothing show cords and ribbons with small metal tips. Similar laces often attached armour to clothing or ring-armour shirts [ref_ill_art_5309] PDF (description 3) [ref_ill_art_5308] PDF. They were made from plant fibres, wool or narrow leather strips [ref_ill_art_5312] PDF.

The tips prevented fraying and helped the laces pass through holes in textiles and armour plates. Small pieces of brass sheet were rolled into shape, then riveted, sewn or pressed onto the lace. The “Hausbuch der Mendelschen Zwölfbrüderstiftung” depicts a specialist lace-maker [ref_ill_art_5328] PDF. Armourers probably bought these products, although they possessed the necessary tools and skills to make them.

Originalwortlaut vergleichen
5.7 Lace production 



By the late 14th century small metal points at the ends of ribbons and cords do appear in the 



depictions of contemporary clothing. Also armour was often attached to the wearer’s clothes 



or ring -armour shirt by means of such fastenings [ ref_ill_art_5309] (descr. 3) 



[ref_ill_art_5308]. The laces were either made of plant - or wool-fibers or from leather cut 



into fine straps [ ref_ill_art_5312]. The small points prevented the ends of the cords and 



ribbons from fanning out and helped to bring them through the holes in the fabric and the 



armour plate. These endings were rolled from small brass plates and then riveted, sewn or 



pressed to the fabric. The “Hausbuch der Mendelschen Zwölfbrüderstiftung” shows a 



specialized craftsman who made such laces [ref_ill_art_5328]. The armourer most likely did



not produce them by  himself, even though he certainly possessed the necessary tools and 



skills for their making.

6 The problem of authenticity

S. 164–165 · Sprachlich überarbeitet · Entwurf

6 The problem of authenticity

Valuable works of art can tempt skilled craftspeople to profit by making convincing substitutes. Imitation is not a modern phenomenon. Competing medieval workshops may already have copied successful armour designs, but such contemporary products would still be regarded as genuine medieval objects today.

There is no recorded evidence of armour being reproduced for collectors before the early nineteenth century. Thereafter, growing demand encouraged the supply of forgeries, declared reproductions, additions and poorly repaired objects. Buyers generally wanted attractive, complete pieces, and genuine armour was often heavily altered to satisfy them. Etching or gilding might be added; surviving original decoration might be polished away because it was incomplete or obscured by corrosion.

Whereas modern conservation usually records interventions, nineteenth- and many twentieth-century restorers left little documentation. During the past 150 years, repaired, supplemented and reproduced objects have become intermixed with armour surviving in a more nearly original state.267 Curators of collections assembled over the past two centuries consequently face questions about particular objects. Identifying alterations and reconstructing object histories are essential: ignoring them can distort our understanding of the medieval past. Any investigation of late medieval armour must therefore consider the authenticity of both the object and its individual components.

The literature offers limited assistance. Few studies have addressed the problem. In 1967 Andrew Mowbray described the “area of forgeries” as “practically a virgin field”, anticipating a major study by Stephen V. Grancsay.268 Grancsay died in 1980 without publishing it. A few general works from the preceding 120 years nevertheless contain guidance, and the principal approaches are examined below. This dissertation does not claim to be the comprehensive study Mowbray envisaged; that would require a large interdisciplinary project. Its aim is to establish a substantial basis for further research.

At the present state of knowledge, authenticity often cannot be settled satisfactorily without unambiguous documentary evidence. Most armour acquired through the antiquities market lacks such documentation. An impressive provenance can be invented, and a history transmitted only orally is difficult to verify. Earlier studies sometimes present their conclusions as final, but closer examination may reveal grounds for doubt. A desire for certainty is understandable; concealing unresolved questions does not advance the subject.

The following sections first consider the historical circumstances behind the problem: how armour was preserved, restored and reproduced. They then examine earlier approaches to authenticity, with particular attention to their limitations.

Redaktionelle Hinweise · 2
  • „whenever any unquestionable documentary evidence can be found“ widerspricht im Original der Argumentation. Im Kontext als „without unambiguous documentary evidence“ gelesen und hier dokumentiert.
  • Mowbrays Aussage ist gekürzt zitiert und ansonsten paraphrasiert; Bedeutung und Beleg bleiben erhalten.
Originalwortlaut vergleichen
6 The problem of authenticity 



Artworks are often high priced goods. Each craftsman or artist capable of reproducing nearly 



identical valuable originals can easily be tempted to make some good money by forging 



artifacts. This is not a modern problem only, plagiarism of successful goods is known 



throughout the ages. Well sellable plate -armour – possibly first designed by a favorite 



workshop – has possibly been copied already in the Middle Ages by competing workshops. 



But such products would nevertheless today be considered as genuine.  



There is no indication that genuine armour had been reproduced for collection purpose 



before the early 1800’s. From then on a growing demand for antique armour was responsible 



for the market-supply of forgeries, reproductions, completions and badly repaired items. The 



potential buyers of ancient armour usually asked for “beautiful” and complete pieces. 



Genuine items therefore often got heavily altered. Decorations like etching or gilding were 



added or – even worse – genuine decorations were polished off as th ey were only partly 



remaining or they were covered by corrosion products. While today alterations are often 



being recorded in a file, the 19 th and even many 20 th century restorers barely documented 



such interferences. Within the past 150 years, the repaired, completed and reproduced items 



have mixed with items of a more or less genuine condition. 267 Each curator of arms and 



armour collections assembled in the last 200 years, is aware of the authenticity -problem of 



the one or the other artwork in his museum. T he responsible of the collections nowadays 



have the task to scientifically divide out all alterations and to reconstruct each item’s history. 



This is necessary as the ignorance of these aspects might falsify the image of the medieval 



past. Therefore, whene ver late medieval armour is examined, one obstacle on the way to 



reliable conclusions has to be attended: The often unanswered question on the authenticity 



of the concerned object or of some of its components.  



The scholar will not find much help in the li terature, as only little research concerned with 



this question has yet been carried out. Just a few articles dealt with the authenticity problem. 



Andrew Mowbray in 1967 said that the “area of forgeries is practically a virgin field and 



will remain so until  a major work on the subject – such as that planned by Stephen V . 



Grancsay – becomes available.” 268 Grancsay until his death in 1980 never published the 



announced work. Anyway, throughout the last 120 years a few “guidelines” got included in 



different general works on arms and armour. The most popular approaches will be introduced 



below. This paper does not want to be understood as the “major work” desired by Mowbray. 



Such a work can only be successful if it is executed in an interdisciplinary large scale 



research project. The present study wants to deliver all the information necessary to build a 



strong basis for further detailed studies on the subject. 



It can be anticipated that, at the current stage of scholarly perception, it is not possible to 



answer sati sfyingly the question on the authenticity of a certain item, whenever any 



unquestionable documentary evidence can be found. For most of the ancient armour pieces 



coming from the antique market no such documentation is at hand. A provenance of good 



sound could have been constructed easily and if it is bequeathed only verbally it remains 



very difficult to prove its validity.  



Some preceding studies might imply that their results on questionable objects are final. Once 



the critical scholars goes deeper into th e material itself, he will very soon get some doubts 



about bottom lines that appear to be set in stone. Of course, it is natural to wish for



unambiguous answers, but masking all remaining doubts is not moving this important 



question any further.  



For the u nderstanding of the authenticity problem it is necessary to describe its historical 



causes. Therefore, some notes on the history of armour -preservation and the history of 



armour restoration and reproduction will be reconsidered. Subsequently, some of the m ajor 



preceding approaches to the problem of authenticity with a focus on their limitations are 



discussed.
S. 165–166 · Sprachlich überarbeitet · Entwurf

6.1 Notes on the history of armour preservation

Provenance is central to questions of authenticity. This study cannot, however, provide either a comprehensive history of armour collecting or the complete provenance of every surviving object. That would require extensive archival research beyond the object examinations already undertaken. Reconstructing histories through the antiquities trade is especially complex and merits a major study of its own.269 Understanding the main kinds of collection is nevertheless indispensable. Where published or otherwise available provenance information could be obtained, it has been entered in the object records.

The essential question is how an object survived to the present. Secure evidence of its existence before 1800 makes modern reproduction unlikely, since no earlier reproduction activity is recorded. Two kinds of provenance are especially useful: objects demonstrably buried before 1800, and objects identifiable in earlier documents, preferably illustrated ones.

A properly conducted and documented excavation offers particularly strong evidence. Only a small proportion of surviving late medieval armour, however, comes from excavations, and many supposedly excavated objects lack adequate find records. They often entered collections after 1800 through purchase or donation. Collectors’ confidence in excavated objects also encouraged dealers to offer deliberately corroded reproductions.

Most surviving armour depended on deliberate preservation. Dynastic and private collections, together with church deposits, can establish authenticity where pre-1800 documentation identifies the objects. Many pieces subsequently passed from these older collections into private hands. Yet claims of archaeological or old-collection provenance still require scrutiny: the history may have been invented.

Five broad collection types can be distinguished. The first three began while the armour remained in use, generally with equipment acquired by a family or institution for defence. Once its practical role ended, it might be retained to commemorate former achievements, much as a racing driver preserves old competition cars, perhaps including a rival’s vehicle—the equivalent here of captured equipment. The fourth category comprises collections assembled from the late eighteenth century onwards, long after the objects had ceased to be used. The fifth combines inherited holdings with later acquisitions. Few historic collections remain in their original locations, and all have suffered losses through sale, theft or warfare.

Originalwortlaut vergleichen
6.1 Notes on the history of armour preservation 



The provenance is a very important factor when the authenticity of a certain item is 



questioned. Nevertheless, the present study can neither provide for a comprehensive history 



of the collecting of armour, nor can all the provenance data on each extant example be 



gathered. Such work would require extensive archival research, additional to the extensive 



object-studies already carried out by the author in the course of this study. The provenance-



reconstruction of items coming from the antique market is often complicated and 



multifaceted. Therefore, it is still waiting to be discussed in a large scale study of its own.269 



Nevertheless, the knowledge of the different types of collections is inescapable for the 



understanding of the provenance-problem and subsequently of the problem of authenticity. 



Fortunately, of many objects all or at least some provenance -stations are published. Where 



the author had data at hand he added it to the object file.  



Particularly when the authenticity of a certain item is discussed, an important question to be 



asked is on its provenance – or more precise: the reconstruction of the way a certain artifact 



was preserved until today. Undoubted documentary evidence on an item’s existence before 



1800 makes it unlikely for it to be a modern reproduction, as no reproduction activities before 



that time had ever been recorded. Reliable information c an be provided by two different 



provenance-types: Objects that clearly came under earth before 1800 and objects that appear 



in – ideally illustrated – documents from before 1800.  



Ideal conditions for the determination of an object as “genuine” are for example provided by 



a provenance from a well -documented and reliably executed excavation. Actually only a 



small part of the existing late medieval armour was excavated. The circumstances of the 



finding of many items that appear to be excavated are often not s ufficiently documented. 



Such objects are found today in many collections, to which they usually came after 1800 



either as a donation or by purchase. As unearthed objects are considered to be genuine, they 



were sought for by collectors. Therefore, some art dealers provided purposely corroded 



reproduced items.  



For the preservation of the larger part of the existing stock some kind of collecting or 



conscious keeping has been the pre -condition. Several dynastic and private collections as 



well as armour preserv ed in churches provide undoubted genuine items, if documentary



evidence of the items from before 1800 exists. Many objects actually came from documented 



“old” collections into private hands.  



Nevertheless, for the examination of archaeological items and su ch allegedly coming from 



“old” collections still caution has to be exercised as criminal minds might simply have 



invented a corresponding story.  



Armour was usually preserved in one of five types of collections. The assembling of the 



armour in the first three groups had basically started in the days when the items were still in 



use. Such an inventory usually consists of objects once acquired for defense by a certain 



noble family or by an institution. The owner or his succession at some time gave up on the 



former designation of the objects and reduced their keeping to the purpose of 



commemorating the past. Like a racing driver that keeps the old fashioned cars of his former 



successes – and maybe another car of a competitor (in our case for example booty) – without 



ever driving them again. The fourth group describes collections that were assembled from 



the late 18th century on, after the collected items had long gone out of use. The fifth group is 



defined by a mix of dynastic and later assembled collections. Only few historical collections 



remained in their more or less original location but all of them suffered major losses, either 



by sales, by theft or by damages throughout violent conflicts. In the following each 



collection-type will be described in further details.
S. 166–167 · Sprachlich überarbeitet · Entwurf

6.1.1 Dynastic collections

Dynastic collections were essentially the private holdings of aristocratic families. They often preserve expensive armour attributed to past “heroes”. Collecting to commemorate secular individuals became especially prominent at the end of the fifteenth century. Maximilian I was among the first rulers consciously to assemble armour associated with important people, preserving their memory and encouraging emulation.270

By the mid-sixteenth century, several institutions resembling museums held arms, armour and other works of art. Among the oldest surviving German armouries is the collection associated with August I’s “Kunst- und Raritätenkammer” in Dresden, established in 1556. Its costly arms and armour consist chiefly of the electors’ personal equipment from the sixteenth and seventeenth centuries.271 Its few fifteenth-century objects were acquired on the antiquities market from the final third of the nineteenth century onwards, mainly from the Zschille collection.

The Real Armería in Madrid followed. From 1565 Philip II collected the equipment of Charles V and other ancestors. It contains relatively little fifteenth-century field armour.272 A third, particularly impressive historic collection was assembled by Archduke Ferdinand II of Tyrol (1529–1595). From 1565 he brought together armour attributed to ancestors and other past and contemporary “heroes” at Ambras Castle near Innsbruck.273

An illustrated catalogue of most of Ferdinand’s suits appeared after his death, in Latin in 1601 and German in 1603.274 Its text concerns the depicted individuals’ achievements rather than the armour itself. Ambras thus used objects to evoke former owners rather than treating them primarily as works of art. The desire to associate armour with famous historical figures remains apparent in later public museums.

Much of Ferdinand’s collection survives. Transferred to Vienna in 1806, it has formed the largest part of the Hofjagd- und Rüstkammer since 1888.275 Laurin Luchner published its history and proposals for reconstructing the Ambras displays in 1958.276 Some holdings returned to Ambras in 1980–1981. Beyond its size, the collection is important for preserving exceptionally costly genuine armour from the second half of the fifteenth century, often associated with named makers and owners. Repairs, restorations and additions nevertheless mean that not every present detail is original.

Smaller dynastic collections of the sixteenth and seventeenth centuries also survive, including the Armeria Reale associated with Charles Emmanuel I in Turin, with later additions, and the Fürstlich-Hohenzollern’sche Sammlungen in Sigmaringen.

Churburg’s armoury is small but exceptionally important for the age and condition of its holdings. It began with the personal equipment of the counts of Matsch from the late fourteenth century onwards. Their successors, the Trapp family, added their own equipment. Despite sales around 1930—fortunately often to public collections abroad—many rare objects remain at the South Tyrolean castle. Even some of the earliest retain original straps, linings and textile or leather gloves.

Alongside several nearly complete fifteenth-century suits, Churburg preserves numerous examples of ordinary soldiers’ equipment. This distinguishes it from collections such as Madrid and Vienna, whose founders were little interested in retaining inexpensive infantry armour. Other dynastic armouries containing both costly and ordinary equipment survive, but are usually smaller and chiefly post-1500, as at the Esterházy family’s Forchtenstein Castle. The armoury of the Grandmaster’s Palace in Malta is a distinctive and important collection spanning both dynastic and arsenal categories.277

Redaktionelle Hinweise · 1
  • Sammlungsdaten und Zuschreibungen bleiben Angaben der Dissertation; keine Aktualisierung der heutigen Museumsbestände.
Originalwortlaut vergleichen
6.1.1 The dynastic collection  



Dynastic collections are or were basically private collections of aristocratic families. They 



often contain costly armour attributed to the “heroes” of the past. The intention of collecting 



items for the remembrance of certain secular persons comes to a first height by the end of 



the 15th century. King Maximillian I. was one of the first rulers who consciously collected 



armour of important persons to keep the memory of their doings alive and to encourage their 



followers to act like these idols.270 The mid-16th century saw the emergence of a number of 



museum-like institutions of arms, armour and other artworks. One of the oldest armouries to 



be preserved in Germany is probably August I.’s “Kunst- und Raritätenkammer” in Dresden, 



established in 1556. Until today this collection includes a large number of costly arms and 



armour, merely the Prince Elector’s private armour from the 16 th and 17 th century.271 The 



few pieces of the 15th century were acquired on the antique market since the last third of the 



19th century, merely from the private Zschille collection. The Dresden collection was 



followed by the also still existing Real Armería in Madrid. Philipp II. from 1565 on collected 



the arms and armour of Emperor Charles V . and other s of his ancestors. The collection 



contains relatively few field armour pieces of the 15 th century.272 The third collection in the 



group, and still the most impressive of all historic armour collections, was compiled by 



Archduke Ferdinand II. of Tirol (1529-1595). From 1565 on he gathered a huge amount of 



armour attributed to his ancestors and other “heroes” of the past and of his own times in the 



castle of Ambras, close to Innsbruck. 273 After his death, in 1601 (Latin edition) and 1603



(German edition) an illu strated catalogue of most of his suits of armour was published. 274 



This early catalogue in its text never refers to the armour shown on the prints but instead to 



the doings of the depicted persons themselves. Thus the collection of Ambras cannot be seen 



like a museum that focuses its attention to the art of the object. It rather uses the latter to give 



a visual impression of the former owners of the armour. The desire of the collectors for 



attributing their object to famous historical persons can be felt in m odern public museums 



until today. However, a great portion of the stock of Ferdinand’s collection survives and was 



transferred to Vienna in 1806, where since 1888 it forms the largest part of the Hofjagd- und 



Rüstkammer inventory in Vienna 275. The history of  the collection at Schloss Ambras, 



including the suggestions for a reconstruction of the former installations, was published by 



Laurin Luchner in 1958.276 Parts of the collection were brought back from Vienna to Ambras 



in 1980-81. This collection is not only of the highest importance because it is the largest one. 



It is also one of the few still existing collections containing the most costly genuine armour 



from the second half of the 15 th century, often even identified with its former maker and its 



owner. Anyway, due to completions, repairing and restorations not all the details on the 



armour now in the Hofjagd- und Rüstkammer in Vienna can be considered as original.  



Some further, smaller dynastic collections of the 16 th and 17 th century do still exist. For 



example the Armeria Reale of Karl Emanuel I. in Turin (with later additions) or the Fürstlich-



Hohenzollern’sche Sammlungen in Sigmaringen. 



A small but – concerning the original condition and the age of the items – very important 



collection is the armoury of the Churburg castle. The collection is based on the armoury of 



the Counts of Matsch, comprising private arms and armour from the late 14 th century on. 



The successors of the Matsch family, the Trapp family enlarged the stock of armour of their 



predecessors by their own equipment. After the sale of several items about 1930 – fortunately 



most of them are now in international public collections – a lot of rare armour is still kept in 



the castle in southern Tirol. The artifacts are particularly precious as even the oldest parts of 



the late 14th century often retain original leather straps, linings and textile or leather gloves. 



Besides the doubtless importance of several nearly complete armour-suits of the 15th century, 



the many extant examples of simple soldie r’s armour is worth to be mentioned explicitly. 



This is also the main difference between other ancient dynastic armour collections and the 



Churburg armoury. For example the initiators of the collections in Madrid or Vienna were 



not interested in keeping the simple foot soldier’s equipment.  



Nevertheless, some further dynastic armouries with costly and foot soldier’s armour still 



exist. Usually these collections are comparatively small and contain items from after 1500 



only, like for example the collections of the Esterházy family in the castle of Forchtenstein. 



A unique and important collection that may be attributed to both, the group of dynastic and 



of arsenal collections is the armoury of the Grandmaster’s Palace in Malta.277
S. 167–168 · Sprachlich überarbeitet · Entwurf

6.1.2 Arsenals

Arsenals were generally public institutions and chiefly held less expensive infantry equipment. Once their contents ceased to be useful in combat, the authorities either disposed of them or retained them as relics of earlier defenders. Preservation required accepting the continuing cost and effort of maintenance.

Many “Zeughäuser”, or arsenals,278 were established in the early fifteenth century to store garrison or municipal arms and ammunition. Substantial quantities of fifteenth-century armour survived from arsenals at Rhodes, Chalcis and Istanbul. Vienna and Munich initially stored military equipment in several locations, usually towers in the city walls. Their earliest surviving inventories, both dated 1444, list projectile weapons, associated equipment and chiefly siege material, but no armour.

Munich already had a separate municipal arsenal building around 1430, alongside these dispersed stores. Vienna’s first dedicated Zeughaus, behind St Laurenz at the Fleischmarkt, was not built until about 1532–1534.279 Both cities retain substantial late fifteenth-century and later holdings. Munich has several frontal torso defences from the final third of the fifteenth century; Vienna preserves many infantry examples from around 1500. Surprisingly few contemporary helmets survive in either collection.

Vienna’s earliest plate armour dates to the 1450s: a composite human suit [ref_arm_4090] PDF and nearly complete Italian horse armour (WM acc. nos. 127.151–153 and 127.157–159). These probably entered later, perhaps as aristocratic donations.280 A composite suit, or its components, on long-term loan to the Goldenes Dachl museum in Innsbruck may likewise have reached the arsenal after its period of use.

Other fifteenth-century Vienna objects include Type IV breastplates [ref_arm_3703] PDF [ref_arm_3738] PDF [ref_arm_3739] PDF [ref_arm_3740] PDF [ref_arm_3741] PDF [ref_arm_3742] PDF [ref_arm_3743] PDF [ref_arm_3744] PDF [ref_arm_3745] PDF, a Type II backplate [ref_arm_3371] PDF and Type VII helmets [ref_arm_1894] PDF [ref_arm_1895] PDF.281

All surviving arsenals have received purchases or donations over the past two centuries, so the provenance of individual objects is not necessarily secure. Extensive restoration, repair and completion, particularly in Vienna, can make original appearances difficult to reconstruct.

Many historic public arsenals have been dispersed. Most of the Bernau armoury, for example, was sold in the 1930s to the Berlin collection identified in the source as the Museum für Deutsche Geschichte, now the Deutsches Historisches Museum. Arsenals in Solothurn, Emden and Graz contain little or no pre-1500 armour. Holdings from Zürich and Basel also survive, but were in storage inaccessible to the public at the time of this study.

Redaktionelle Hinweise · 1
  • Die Institutionsbezeichnung „Museum für Deutsche Geschichte“ für einen Verkauf in den 1930er Jahren ist chronologisch zu prüfen. Quellenangabe ausdrücklich kenntlich gemacht statt eine neue Erwerbungsgeschichte zu erfinden.
Originalwortlaut vergleichen
6.1.2 The arsenal 



Arsenals are usuall y of a public character and therefore they comprise merely cheaper 



armour for foot soldiers. At some time the responsible understood that the stored items could 



be of no use for combat anymore. At this point the collection was either liquidated or kept



as an appreciated relic of the glorious “freedom defenders” of old. The latter decision meant 



to accept the effort necessary for the maintenance of the collectibles.  



Many “Zeughäuser” 278 or arsenals were established at the beginning of the 15 th century. 



Garrisons or city -authorities kept their arms and ammunition in such stores. In Rhodes, 



Chalcis and Istanbul parts of arsenals comprising huge amounts of 15th century armour were 



preserved. In Vienna and Munich all the war-material was stored in different places, usually 



in the towers of the city walls. The earliest inventory of the Vienna and the Munich city 



arsenals, both from 1444 do not include armour, but the ballistic weapons with all their 



belongings and mainly material for the besieging of hostile fortifi ed places. In Munich 



already by 1430 in parallel to these storages an city-arsenal in a building of its own existed, 



while in Vienna it took until about 1532 -34, when the first Zeughaus at the Fleischmarkt 



behind St. Laurenz was built. 279 The arsenals of Mun ich and Vienna still retain a 



comparatively huge part of their inventory from the late 15 th century and later. While in 



Munich there are several torso front -protections from the last third of the 15 th century, in 



Vienna there are many torso front -protections for infantry from around 1500. Surprisingly 



in both collections there are only a small number of head pieces of the same period preserved. 



The earliest plate armour items in the Zeughaus of Vienna date from the 1450ies: a composite 



suit for a man [ ref_arm_4090] and a nearly complete horse armour of Italian production 



(WM acc. no. 127.151-153 and 127.157-159). These early items are considered to have come 



later into the city-arsenal, probably as donations from a noble owner.280 A composite suit of 



armour for the man (or its parts), on permanent loan to the Museum in the Goldenes Dachl 



in Innsbruck, was probably also given to the Zeughaus in a time after its use. The remaining 



parts of the 15 th century in Vienna are breastplates of type -IV [ ref_arm_3703] 



[ref_arm_3738] [ ref_arm_3739] [ ref_arm_3740] [ ref_arm_3741] [ ref_arm_3742] 



[ref_arm_3743] [ref_arm_3744] [ref_arm_3745], a backplate of type-II [ref_arm_3371] and 



helmets of type-VII [ref_arm_1894] [ref_arm_1895].281  



All the still existing Zeughäuser had gained additional objects by donations or by purchase 



throughout the last 200 years. This means that also here the provenance of many objects is 



not absolutely certain. Heavy restorations, repairing and completions, fo r example at the 



objects in the Vienna Zeughaus, make the reconstruction of the genuine appearance of the 



single items very difficult.  



Many historical “public” arsenals were dispersed over different collections throughout the 



last 200 years. For example m ost of the stock of the Bernauer Rüstkammer was sold in the 



1930ies to the Museum für Deutsche Geschichte in Berlin, now the Deutsches Historisches 



Museum. Further arsenal stores containing no or only very little armour from before 1500 



can be visited in Solothurn, Emden and Graz. Some stock of the former Zeughäuser of Zürich 



and Basel still exists, but is kept in storage not accessible for the public.
S. 169 · Sprachlich überarbeitet · Entwurf

6.1.3 Armour preserved in churches

During the period studied, burial in armour was no longer practised in Europe. Armour found in churches was generally deposited as a votive offering by someone who had escaped danger, or displayed near a tomb to commemorate the deceased’s martial achievements. Such preservation was especially common in England,282 but also accounts for important Italian suits.

Around 1930, several suits at the Santuario della Madonna delle Grazie in Curtatone near Mantua, previously thought to be made of papier-mâché, were recognised as assemblages of genuine armour.283 In Germany, a late fifteenth-century suit survived in the church at Schwäbisch Gmünd.284 All these examples are documented before 1800, but all have also undergone modern restoration.

Originalwortlaut vergleichen
6.1.3 Armour preserved in churches 



In the considered period nowhere in Europe men were buried dressed in their armour 



anymore. Where armour is or was found in churches, it was usually once deposited as a 



votive offering from a person saved from danger. Arms and armour was kept also close to 



the church-tombs as a long lasting memory of the deceased’s heroic manners. Especially in 



England armour was often kept in churches282, but also in Italy several important suits were 



preserved this way. About 1930 in the Santuario della Madonna delle Grazie a Curtatone 



near Mantua a number of armour suits – until then considered to be made of “papier-maché” 



– were recognized as being composed from genuine armour parts.283 In Germany a late 15th 



century armour -suit was preserved in the church of Schwäbisch Gmünd 284. All these 



examples are named in documents from before 1800, but all the named objects got altered 



by modern restorations.
S. 169–171 · Sprachlich überarbeitet · Entwurf

6.1.4 Collections assembled in modern times

Many private collections were assembled afresh during the past two centuries. A few aristocratic collectors built on small inherited holdings, while wealthy non-aristocrats also began collecting. These developments belong to the political and social changes of the nineteenth century. The French Revolution challenged the established order, and across Europe aristocratic political power increasingly passed to other groups. Restoration after the Congress of Vienna delayed democratic change but did not remove the nobility’s concerns about status and wealth. Industrialisation meanwhile created prosperous business owners and a growing class of patrons interested in contemporary art and antiquities.

Beyond their practical function, arms and armour carried symbolic associations with noble conduct, fairness, respect and strength. Some wealthy citizens and aristocrats sought to affirm their social standing through collections of these historic status symbols, following the example of princely families since the sixteenth century.

Romanticism also renewed interest in chivalry. Horace Walpole’s (1717–1797) “The Castle of Otranto” and Sir Walter Scott’s (1771–1832) “Ivanhoe” were especially influential.285 Walpole had already evoked the medieval past through Strawberry Hill’s architecture in the third quarter of the eighteenth century. From the 1770s, Count Franz I of Erbach-Erbach collected old arms and armour and converted rooms in his late-Baroque castle into a spacious “Gothic” hall. Much of his collection remains at Schloss Erbach.

Early nineteenth-century artists developed a more attentive understanding of medieval and Renaissance material culture. Around 1809, Franz Pforr (1788–1812) depicted Emperor Rudolf of Habsburg’s entry into Basel [ref_ill_art_5348] PDF with a remarkably convincing early sixteenth-century setting, including its armour. Interest in the details of the past had revived.

Re-enactments soon followed. Sweden hosted several tournaments in medieval or Renaissance style during the final third of the eighteenth century.286 The best-remembered early event, owing to its ambitious organisation, is the Eglinton Tournament of 1839.287 The Earl of Eglinton, Sir Archibald Montgomery (1812–1861), persuaded about forty noblemen to acquire tournament armour and train for a year. London dealer Samuel Pratt supplied both originals and reproductions. Some equipment survives and was displayed in a dedicated room at the Royal Armouries in Leeds.

Large quantities of medieval and Renaissance armour still remained in castles and arsenals. From the early nineteenth century, owners and municipalities sold holdings to private collectors to raise money or release space.288 European armour preserved in the Ottoman-controlled Aegean was also sold and transported to western Europe and North America. Dealers such as Samuel Pratt in London and, later, Victor Bachereau in Paris drew on this expanding supply.289

Probably most surviving armour passed through private collections from the nineteenth century onwards. Objects were repeatedly sold or exchanged, and the continuing market makes provenance an evolving field requiring careful documentation.290 The total surviving stock of pre-1500 field armour, including a few identified reproductions, is estimated here at no more than 6,000 objects. By comparison, Graz alone preserves about 5,000 sixteenth- and seventeenth-century pieces. Late medieval armour was therefore always scarce and highly valued by collectors.

Notable nineteenth- and twentieth-century private collections include the following; some have since been dispersed. France: Arosa, Spitzer, W. H. Riggs and Napoleon III. England: Wallace, Laking, Scott, Duc de Dino, Meyrick, De Cosson and Noel Paton; the Wallace collection remains intact. Italy: Poldi Pezzoli, Stibbert and Luigi Marzoli, all surviving as collections. Germany: Soeter, Hefner-Alteneck, Kuppelmayer and Zschille. Austria: Wilczek and Till. United States: Hearst, Dean and Severance. Russia: Tsar Alexander I, now in the Hermitage, St Petersburg. Sweden: Hallwyl.

Redaktionelle Hinweise · 1
  • Zeitgebundene Ausstellungs- und Bestandsangaben entsprechen dem Stand der Dissertation. Pforrs dargestelltes Ereignis und die hier behauptete frühneuzeitliche Ausstattung werden nicht stillschweigend chronologisch gleichgesetzt.
Originalwortlaut vergleichen
6.1.4 The modern assembled collection 



Throughout the last 200 years many private collections were entirely reassembled. In a few 



cases some nobles built their collections on the basis of small collections from ancient family 



possession. Also rich privateers started to collect arms and armour. The reasons that made 



nobles and privateers collecting armour need to be seen on the historical circumstances. At 



the Beginning of the 19th century the whole western world went through major political and 



social changes. The French Revolution had just overthrown what has been the state of the 



art since antiquity. In many countries the nobility had to give the government into the hands 



of non-aristocratic citizens. This develop ment was about to take over to all the European 



countries throughout the 19th until the early 20th century. Of course, restoration politics after 



the Congress of Vienna postponed the establishment of democracies, but nevertheless the 



aristocrats were strug gling to keep their social status – and their wealth. The industrial 



revolution from the 18 th century on played an important role in these developments. Some 



citizens had become rich by founding production companies. With the establishment of a 



new wealthy , non -aristocratic social class a new and steadily growing interest for the 



patronage of arts aroused. Contemporary arts were encouraged by rich donors and antiquities 



became more and more valued.  



Arms and armour – besides their designation for combat – always had a symbolic meaning. 



As leftovers of the times of knighthood they stood for a noble attitude, fairness, respect and 



strength. Some of the new wealthy and increasingly politically influential citizens as well as 



some wealthy aristocrats sought to legitimate their social status by assembling large 



collections of arms and armour – the most impressive status symbols of the past – just as the 



higher noble families had done since the 16th century.  



In parallel to the social changes the Romanticism of th e late 18 th and early 19 th century – 



first and foremost the novels like Horace Walpole’s (1717-1797) “The castle of Otranto” or 



Sir Walter Scott’s285 (1771-1832) “Ivanhoe” – brought up a new interest for the times of 



chivalry. While Walpole in the third quar ter of the 18 th century had already revived these 



times in the architecture of his castle -like country house Strawberry Hill, Grave Franz I. of 



Erbach-Erbach started to collect antique arms and armour from the 1770ies on. For his 



armoury he also altered so me rooms in his late -baroque castle to form one ample “gothic”



hall. A large part of his collection still can be seen in Schloss Erbach. At the beginning of the 



19th century an increasingly sensitive understanding for the medieval and renaissance times 



came up. About 1809 Franz Pforr (1788-1812) in his painting of the entry of Emperor Rudolf 



of Habsburg in Basel [ref_ill_art_5348] for example showed the stylistic ambient – including 



the arm our – of the early 16 th century in a surprisingly correct manner. The love for the 



details of the material culture of the past had awakened.  



It was not long until the first happenings trying to reenact the age of chivalry were set up. 



Several jousts in th e medieval or renaissance manner were held in Sweden already by the 



last third of the 18th century286. The first of such events to be remembered until today – due 



to the enormous efforts of its organization – is the “Eglinton Tournament” of 1839 287. For 



this event the Earl of Eglinton, Sir Archibald Montgomery (1812 -1861), convinced about 



forty nobles to acquire tournament armour and to train for one year for a real joust. The arms 



and armour was provided by the London art dealer Samuel Pratt, who sold original  and 



reproduced items to the participants. Some of the equipment survives until today and is 



exhibited in a special showroom in the Royal Armouries in Leeds.  



Since the time of its use huge quantities of medieval and renaissance armour was still kept 



in many castles and arsenal stores. From the beginning of the 19th century the private owners 



or the city communities often sold such stock to rich privateers to make some easy money 



or to gain space in their estate for various purposes. 288 Medieval European armour that 



survived for different reason in the Ottoman-ruled Aegean region was sold from the arsenals 



and was brought to Western Europe and North America. Huge amounts of armour from 



different sources came into the flourishing antique market. From such sources dealers like 



Samuel Pratt in London and later Victor Bachereau in Paris got their goods from.289  



Probably the largest part of still existing armour from the 19th century on was sold to private 



collectors. Privately owned items were  often sold or exchanged within the society of 



collectors. A market for antique arms and armour still exists today and therefore provenance-



history is still a changing field that requires good documentation. 290 The estimated total 



number of extant armour pie ces for field use from before 1500, including few identified 



reproductions, might reach at most 6000 objects. When comparing this to the number of 



5000 16th and 17th century items preserved alone in the Landeszeughaus Graz, it becomes 



clear that for armour collectors the late medieval pieces throughout all the times of armour 



collecting were not easy to get and thus they were highly valued.  



Some private collections of the 19 th and 20ieth century shall be named. Some of them are 



now dispersed to different locations: 



France: Arosa, Spitzer, W. H. Riggs, Napoleon III. 



England: Wallace (still existing), Laking, Scott, Duc de Dino, Meyrick, De Cosson, Noel 



Paton. 



Italy: Poldi Pezzoli, Stibbert, Luigi Marzoli (all three still existing).



Germany: Soeter, Hefner-Alteneck, Kuppelmayer, Zschille. 



Austria: Wilczek, Till. 



USA: Hearst, Dean, Severance. 



Russia: Tsar Alexander I. (now Eremitage St. Petersburg). 



Sweden: Hallwyl
S. 171 · Sprachlich überarbeitet · Entwurf

6.1.5 Mixed collections

The rapid expansion of public historical museums in the second half of the nineteenth century brought many individual arms and armour objects into new collections by purchase or donation. Museums without an armour specialism consequently often hold a few examples.291

From the early twentieth century, museums increasingly purchased private holdings to preserve them for public access. Some now combine dynastic, arsenal and modern collecting histories. The Royal Armouries in Leeds, for example, preserves historic crown holdings alongside acquisitions made during the past two centuries. Among the most important private purchases was the horse armour attributed to Duke Waldemar VI of Anhalt-Zerbst, acquired by the Tower Armouries in 1959 (now Royal Armouries, acc. no. VI.379). The Musée de l’Armée in Paris, Livrustkammaren in Stockholm and Kremlin Armoury in Moscow similarly expanded through nineteenth- and twentieth-century purchases and donations.

Originalwortlaut vergleichen
6.1.5 Mixed collections  



With the rapidly growing number of public historical museums in the second half of the 19th 



century many single arms and armour pieces were sold or donated to the newly assembled 



collections. Therefore, several museums not specialized on armour today contain the one or 



the other piece of armour.291 



With the beginning of the 20ieth ce ntury museums started to buy a lot of armour from 



privateers with the intention of preserving it for the public. Some of these collections now 



contain a mix of dynastic, arsenal and modern assembled collections. For example the Royal 



Armouries in Leeds pre serve the old armouries of the crown as well as additional items 



acquired throughout the past 200 years. The most precious purchase from private possession 



was probably the horse armour attributed to Duke Waldemar VI. of Anhalt -Zerbst, which 



came into the Tower Armouries in London in 1959 (now Royal Armouries in Leeds, acc. no. 



VI. 379). This is similar to the inventories of the Museé del’Armeé in Paris, the 



Livrustkammaren in Stockholm and the Kremlin Armouries in Moscow, that all acquired 



several collectibles from donations or by purchase throughout the 19th and the 20th century.
S. 171–175 · Sprachlich überarbeitet · Entwurf

6.2 Notes on the history of armour reproduction and restoration

Armour was certainly being reproduced by the second third of the nineteenth century, as equipment made for the Eglinton Tournament of 1839 demonstrates.292 Growing demand could not be met by surviving originals, particularly scarce early examples.

Distinguishing originals from reproductions may seem straightforward. In much of Europe, armour-making traditions had been interrupted for centuries, and industrialisation introduced many new metalworking techniques. Scholars therefore often assumed that traces of modern manufacture would expose reproductions. Yet nineteenth-century craftspeople still practised older methods, including nail-forging and fire gilding, and could obtain material made by traditional processes. Museum objects were also often displayed without glass, sometimes allowing direct measurement.293 A skilled worker’s products may consequently be difficult to distinguish from originals. The history of reproduction therefore deserves attention.

Two categories should be distinguished: objects openly sold as reproductions and objects intended to deceive. Several European firms offered declared reproductions in the late nineteenth and early twentieth centuries, but unfortunately did not consistently mark them as such.

Laking identifies Italy as the earliest centre, describing poor-quality work made there in the early nineteenth century. Without citing evidence, he names three families producing reproductions and forgeries: the Diamante in Rome, Gaggini in Milan and San-Quirine in Venice. Their suits entered the market between 1865 and 1880. He contrasts Italian “flamboyant renaissance types” with German “Maximillian and so called gothic-types”.294 He also describes French production around 1860–1870 as “excellent and most deceptive armour and weapons”, praising the originality and care invested in it.295

Laking names Leblanc-Granger and Charles Rouget, who made imaginary suits for the Paris opera. Around 1875, a Mr Klein in Paris produced decorative suits, while Antoine Vechte was regarded as a master of the craft.296 An armourer named Francis worked in London in the 1880s.297

Some firms, notably Ernst Schmidt’s Munich atelier, issued catalogues.298 Schmidt probably did not make armour himself. Lorenz Kilian, who died in 1919, may have produced most of his stock, although other craftspeople also worked for him.299 Schmidt advertised traditional production methods,300 apparently recognising that the originals’ material differed from modern stock. His catalogues may also illustrate genuine objects, which he evidently sold alongside reproductions.301 An illustration can sometimes establish modern manufacture, just as secure pre-1800 documentation can establish an object’s earlier existence, but its context must be assessed.

Most Schmidt products remain difficult to trace, although a few locations are known.302 Before 1904, Karl Gimbel of Baden-Baden assembled an educational collection composed almost entirely of reproductions.303 Mowbray attributes its suits [ref_arm_4115] PDF304 and [ref_arm_4131] PDF305 to Schmidt’s atelier. Other Gimbel suits may share that origin but do not appear in the catalogue. Most of his collection, reportedly including these suits, subsequently reached the Marksburg and was displayed in the “Rittersaal”. A copy [ref_arm_3262] PDF of the Vienna suit [ref_arm_3258] PDF, said to come from Schmidt, was displayed in the entrance hall of the Higgins Armory in Worcester.

Schedelmann names further makers of high-quality reproductions:306 C. W. Fleischmann and Joseph Hugel in Munich,307 M. R. Schmerha in Vienna, and the elusive Wessely. Leopold Winkelmayer of Vienna reportedly sold work both as original and as reproduction. Unprotected museum displays allowed him close inspection and even measurement. Schedelmann states that he used a maker’s mark and oversized civic marks, but gives no supporting reference.

The prosecution of Viennese dealer Salomon Weininger identifies another skilled maker, Johann Böck. Weininger borrowed originals from public collections, had Böck copy them, and returned the copies until the substitution was discovered.308

Laking was probably the first to publish an account of London dealer Samuel Pratt and his armourer Thomas Grimshaw’s mid-nineteenth-century trade in forged armour. Grimshaw chiefly made imaginary medieval helmets, but also entire fantasy suits, apparently dating stylistically from the tenth to fourteenth centuries. Laking described many of them.309

Karen Watts revisited the pair in 1992. At least seventy-five Grimshaw helmets were sold through Pratt to Robert Curzon, later Baron Zouche. These forgeries appear relatively easy to identify. A scrapbook attributed to Grimshaw, now at the Royal Armouries in Leeds, contains sketches of many helmets. He seems mainly to have used historic depictions rather than surviving objects as models.310

The early twentieth-century partnership of Konrad and Kahlert had a wider impact, chiefly on historic weapons. Konrad was a highly skilled maker; Kahlert placed his work on the market. By acquiring Konrad’s estate, Hans Schedelmann secured correspondence documenting commissions for forgeries. His first article appeared in 1948, ten years after Konrad’s death.311

Konrad probably made little armour. In 1924, when Dresden museum staff sought his opinion on a helmet offered for sale, he admitted having made it years earlier but said he no longer undertook such unprofitable work.312 Its present location is unknown. No armour has been securely attributed to him; most assigned objects are staff weapons. Kahlert nevertheless sold armour, including hand defences [ref_arm_1084] PDF [ref_arm_1130] PDF, but also traded in originals, so a Kahlert provenance alone does not establish forgery.

Not all reproductions were forged from sheet. The Stolberg’sches Eisenwerk in Ilsenburg near Wernigerode and Karl (Carl) Haas in Vienna offered electroformed armour in the late nineteenth century.313 This process differs fundamentally from conventional armour-making.314 Developed by the mid-nineteenth century,315 it deposits metal electrochemically from a solution onto a conductive mould. The deposit thickens until it can be separated as a self-supporting object.

An electroformed interior would probably lack hammer marks. Unless subsequently worked, turned edges might be solid, while rivets and applied decoration might form part of the same shell. Electroformed metal is often assumed too brittle for forging, making hammered edges or embossing impossible. Some processes did produce brittle material, but the nineteenth-century chemist Klein obtained iron that could be forged and welded after heating it to red heat.316 Electroformed objects could therefore potentially have been hammered to resemble forged work.

I have not encountered an apparently electroformed object in fifteenth-century style. The method was probably used chiefly for the elaborate embossing of later armour. Preparing moulds was labour-intensive, so production was probably economical only when each mould yielded several copies.

Many reproductions were certainly intended to deceive. Forgers worked secretly and generally avoided documentation. Surviving evidence is exceptional: Grimshaw’s scrapbook records objects made or contemplated,317 and Kahlert retained correspondence with Konrad. In other cases, further evidence may be impossible to recover. Even known documents often cannot be matched to objects because sales went unrecorded.

Direct sales from workshops to private collectors left no catalogues. Objects could appear suddenly with only a dealer’s oral provenance, which buyers often accepted. Repeated transfers obscured doubtful origins, and acquisition from a respected collection could dispel earlier reservations.

Collectors frequently wanted complete suits. Some were assembled entirely from genuine components, but many museum suits combine originals with reproductions because suitable historic pieces were unavailable. Replacement components may initially have been sold openly as copies, only for that information to disappear, deliberately or inadvertently, when ownership changed.

Redaktionelle Hinweise · 3
  • „Electro-plating“ wurde für die Herstellung eigenständiger Metallschalen präzisiert zu „electroforming“; der Originalbegriff bleibt im Originalauszug. Beschichtungen bereits vorhandener Objekte werden weiterhin als Plattierung bezeichnet.
  • Der Haupttext lokalisiert ref_arm_4115 an der Marksburg, während Anm. 304 den Verbleib offen nennt. Widerspruch erhalten und zur Klärung markiert.
  • Der historische Stand von Museumsnamen und Ausstellungen bleibt erkennbar; keine Behauptung über heutige Präsentationen.
Originalwortlaut vergleichen
6.2 Notes on the history of armour reproduction and restoration 



At least from the second third of the 19th century on292 armour has been reproduced, like the 



items made for the Eglinto n tournament of 1839 proof. The reasons why craftsmen started 



to reproduce antique armour are simple: A growing demand could not be satisfied by original 



items – especially early armour existed in only few examples.  



It is inviting to imagine the distincti on between genuine and reproduced armour as easy. In 



Europe for the most part the tradition of armour making has been interrupted for centuries. 



In the 19th century the industrial revolution had already generated so many new inventions 



in the sector of metal-work that scholars often suggested that the modern-made armour could 



easily be unmasked by detecting fingerprints of modern techniques. Until today it is  



generally ignored that the 19th century still saw good craftsmen, trained in ancient techniques 



like nail-forging, fire gilding etc. and even their working-material might still have been made 



by old techniques. Furthermore, at that time the collectibles i n public museums were often 



not behind glass and in some cases they could even be accessed for taking measurements.293 



Therefore, it might be difficult to tell the products of some skilled modern workers apart 



from the genuine items. For these reasons, it is important to reconstruct the history of armour 



reproduction in a short sketch.  



Two types of reproductions need to be generally distinguished. One was sold by the maker 



or a dealer as a reproduction and the other one was made to deceive a potential buyer. In the 



late 19 th and early 20 th century in different European countries several companies offered



“declared” reproductions. Unfortunately , the products were never clearly marked as 



reproductions.  



Laking considers Italy to be the place where armour has been reproduced first. He says that 



poor quality work was made there already by the early 19 th century. Furthermore – 



unfortunately without any reference – he mentions three families making reproductions and 



forgeries of arms and armour: The Diamante in Rome , the Gaggini in Milan and the San -



Quirine in V enice. The suits they produced came into the market in the years between 1865 



and 1880. He says that the Italians reproduced merely the “flamboyant renaissance types”, 



in contrary to the German colleagues who specialized on the “Maximillian and so called 



gothic-types”.294 In France between 1860 and 1870 “excellent and most deceptive armour 



and weapons”  were produced, “forgeries that are interesting because they showed 



originality and were made with much care and thought.”295 Laking adds to the list of 



reproducers also the names Leblanc -Granger and Charles Rouget who both made fantasy 



suits of armour for the Paris opera. Also in Paris, about 1875 a certain Mr. Klein made 



reproductions of suit for decoration but also a “real master” of the armourer’s craft worked 



there: Antoine V echte. 296 In London in the 1880ies an armourer called Francis was 



working.297 



Some of these companies, like the Atelier of Ernst Schmidt in Munich, published catalogues 



of their offers. 298 Ernst Schm idt was probably not making armour himself. Most of his 



products were possibly made by the armourer Lorenz Kilian who died in 1919, but Schmidt 



had also other craftsmen working for him. 299 He even promoted his products by promising 



to use old production methods for their making300, obviously already back then being aware 



that the originals were made of a material different from the modern. Another problem is 



that the images in his catalogue might also show original arms and armour parts which 



Schmidt apparently also sold. 301 Just like undoubted documentary evidence on an item’s 



existence before 1800 can proof its authenticity, in some cases the catalogue image of a 



certain item might proof that it is a modern reproduction. Today it is very difficult to track 



down where all the Schmidt items went and where they are now. Anyway, the current 



locations of few items are known.302 For educational purpose the Baden-Baden Karl Gimbel 



before 1904 had assembled a large collection consisting almost exclusively of



reproductions.303 The suits [ ref_arm_4115]304, [ ref_arm_4131]305 of the Gimbel’sche 



Waffensammlung according to Mowbray came from Schmidt’s Atelier. Maybe Gimbel had 



ordered also other suits from there, but they are not illustrated in Schmidt’s catalogue. Most 



items from Gimbel – including the two aforesaid suits – later came to the Marksburg, where 



they are currently exhibited in the “Rittersaal”. In the entrance hall of the Higgins armoury 



at Worcester a copy [ref_arm_3262] – said to come from Schmidt’s Atelier – of the Vienna 



suit [ref_arm_3258] was exhibited.  



According to Schedelmann 306, Schmidt had some competitors producing also good quality 



reproductions. He names “C. W. Fleischmann” and “Joseph Hugel”307 in Munich, “M . R. 



Schmerha” in Vienna and a “mysterious” master Wessely. An armourer who is said to have 



sold his products as both, original and reproduction, was Leopold Winkelmayer in Vienna. 



It was easy for him to get very close to extant armour pieces, as in many m useums of the 



19th the artifacts were displayed without glass and often even without any barrier. Thus it 



was even possible to take measurements on the originals. Schedelmann says that 



Winkelmayer even used an armourer’s mark and “too large” city marks. Un fortunately he 



does not give a reference for this assumption. Through the criminal-case on the Vienna art 



dealer Salomon Weininger the name of a further skilled 19 th century armourer is known: 



Johann Böck of Vienna. Weininger had borrowed original pieces from public collections and 



had copies of them made by Böck. Weininger then gave back the reproductions until his 



deception was discovered.308  



Laking has probably been the first to publish some notes on the mid-19th century production 



and trade of faked armour by two gentlemen, the London art Dealer Samuel Pratt and his 



armourer Thomas Grimshaw. This forger merely produced imaginary medieval helmets, but 



he also constructed whole fantasy suits of armour. His objects by their “style” seem to date 



from the 10th to the 14th century and many of them were described by Laking.309 



In 1992 Karen Watts published an article that deals again with the duo Pratt and Grimshaw. 



She notes that at least 75 of Grimshaw’s helmets were sold via Pratt to Robert Curzon, later 



the Baron Zouche. Grimshaw ’s forgeries seem to be rather easily identified as such. A 



scrapbook attributed to his own hand with sketches of many helmets is preserved in the 



Royal Armouries in Leeds. It seems like he main ly worked after depictions of armour i n 



contemporary artworks and not after extant examples.310  



Similar to the Grimshaw case – with a much wider impact on the total stock of merely ancient 



arms – were the early 20 th century forging and selling activities of  the duo Konrad and 



Kahlert. The first was a very skilled craftsman making excellent reproductions and the 



second was an art dealer who brought the forged items into the market. It was Hans 



Schedelmann who – by buying Konrad’s bequest – had secured several  correspondence-



letters of the two that proved the ordering and production of forgeries. Schedelmann



published the first article on their activities ten years after Konrad’s death in 1948. 311 It is 



not likely that Konrad made a lot of armour -reproductions. In 1924 he was asked by the 



Dresden museum officials about his opinion on a helmet offered for sale to the museum. He 



confessed that it was him who made it years ago, but that now he does not do such work 



anymore, as it is not profitable. 312 Unfortunately it is not known where this helmet is 



preserved now. No armour has clearly been identified with Konrad’s hand; most of the 



objects attributed to him are staff -weapons. Nevertheless, his dealer Kahlert sold armour 



parts, e. g. the pair of hand -protections [ref_arm_1084] [ref_arm_1130], but not all Kahlert 



sales were forgeries as he also dealt with original items.  



Not all reproductions of armour were forged from p late-sheet. Several companies also 



offered electro plated replicas of arms and armour. The Stolberg’sches Eisenwerk in 



Ilsenburg (near Wernigerode) and Karl (Carl) Haas in Vienna made electro -plated 



reproductions of armour in the late 19th century.313 



To understand the basic differences to the conventional armour making techniques, it is 



necessary to describe the electro -plating314 method in a few words. Electro plating is a 



technique already developed by the mid-19th century.315 In an electro-chemical process iron 



elements solved in a liquid are joining at the surface of a conductive mold to form a stable 



layer. This layer becomes thicker with the continuation of the process. Once the desired 



thickness is reached the mold can be removed from the metal -artifact. The interior of an 



armour part produced by this technique would probably not show hammer-marks. If the item 



was not finished by forging the turned edges would be massive, maybe it would also be 



recognizable that rivets or a pplications are formed in one part with the plate. Nevertheless, 



it is a widely held belief that electro plated material was generally too brittle to be forged 



and that therefore edges or embossing could not be finished with the hammer. While certain 



electro-plating processes indeed produced only brittle material, in the 19 th century the 



chemist Klein by red -heating the material revealed iron that could be forged and welded – 



just like wrought-iron.316 Therefore, it is actually possible that items were reproduced by the 



electro-plating technique and were subsequently hammered to reveal a forged appearance. 



The author has never seen an armour part of 15th century style, apparently made by electro-



plating. This technique was most likely only used for reproducing more complicated shapes 



at richly embossed items of later periods. Due to the immense effort of the mold-making, the 



production of artifacts was probably only profitable when several items were produced from 



one mold.  



For sure, many objects were made to trick the potential buyer, as a lot of money could be 



made by such sales. It is in the nature of the subject that forgers operated secretly and avoided 



to leave any documentary evidence on their activities. Only in few cases , by chance some 



evidence was fo und. The faker Grimshaw had left his private scrapbook including several 



drawings of the objects he faked or considered to fake. 317 Kahlert had kept many letters of 



the correspondence with his forger Konrad. In the yet unsolved cases it is difficult – if not



impossible – to find further evidence for such activities. Even where it was found, until today 



it is often impossible to identify the produced objects with a documentary source, as usually 



no notes on the sales had been written down. Many reproduced arti cles were first sold 



directly from a dealer’s atelier to private collectors and therefore no catalogues that could 



help to track down provenances exist. Many allegedly genuine armour pieces suddenly 



“popped up” from out of the blue. Most of the private col lectors did not ask for documents 



as they believed in the provenance -story verbally communicated by the seller. To obscure 



their true provenance , many doubtful items went through so many stations that it was 



difficult for a buyer to investigate if they were “clean”. Items were often re-sold by collectors 



and a buy from a collection of good reputation often washed away remaining doubts.  



Many buyers of ancient armour wished to have a complete suit. In a few cases suits of armour 



were composed of genuine piec es. The larger number of museum suits is composed from 



genuine and reproduced parts, as not all missing pieces were available as originals. The 



reproductions that completed a suit were probably initially sold as copies . After the items 



had got handed over to new owners this information often deliberately or unwittingly got 



lost.
S. 175–176 · Sprachlich überarbeitet · Entwurf

6.2.1 Modern alterations

Many surviving objects suffered centuries of neglect. Components were lost or detached, surfaces corroded, and organic fittings decayed. The modern emphasis on conserving an object’s surviving state developed chiefly after the Second World War. Earlier collectors and museums often prioritised appearance, restoring broken or heavily corroded armour to “beauty”.318 Nineteenth-century restorers could still obtain traditionally produced material and use older craft techniques, making their work difficult to date today.

As early as 1890, Wendelin Boeheim opposed completing fragmentary objects. He preferred to display them unchanged beside an image of a reconstruction, arguing that additions further damaged their original state. He advised collectors and dealers to buy a good cast copy from the Stolbergsches Eisenwerk or an electroformed copy from Haas rather than alter an original.319

Extensive repair and completion nevertheless continued in private and public collections. Modern museum interventions are at least generally documented: the right elbow defence [ref_arm_492] PDF, for example, was made in 1956 by Tower Armouries armourer Theodore Egli.320

Some interventions remain troubling. Stephen V. Grancsay described restoring a poorly preserved helmet reportedly from Rhodes. Its ragged holes were cut to regular outlines, then filled with twenty-five shaped patches cut from genuine armour from Chalcis and welded into place.321 A wholly new reconstruction would arguably have preserved more evidence. The result can no longer be treated as an unaltered original. Other restorers likewise used welding: parts of the brim of [ref_arm_1417] PDF were reconstructed with patches. On breastplate [ref_arm_3696] PDF, original waist cut-outs were mistakenly filled with sheet metal.

In the late 1990s, Dieter Müller filled corrosion pits on a genuine suit in his collection by electroplating.322 This substantially altered its surface, although it preserved the plates’ overall shape.

Extensive restoration was still being undertaken at the time of this study, in museums as well as private collections. Archaeological objects were often stabilised with synthetic resin [ref_arm_1520] PDF [ref_arm_3284] PDF; helmet [ref_arm_1460] PDF appears to contain more resin than iron. Damaged painting on the Vienna helmet [ref_arm_1893] PDF was recently completed. In the 1980s, small plates were riveted to the ends of the forehead reinforcement of [ref_arm_1802] PDF, extending it through a misunderstanding of its construction.

The detached visor of that helmet was found in museum storage in 2012. My examination indicated that before removal of the visor and extension of the reinforcement, the helmet had been in an entirely genuine state. Comparisons with [ref_arm_1706] PDF [ref_arm_1718] PDF [ref_arm_1735] PDF support this interpretation and permit reconstruction of its original appearance.

Some repairs may instead address damage incurred during manufacture. Copper-coloured brazing fills several cracks on the crown of [ref_arm_1702] PDF, perhaps formed while shaping the skull. Similar work appears inside [ref_arm_1713] PDF. It also occurs on suspected reproductions such as [ref_arm_1510] PDF, so its presence does not establish a medieval date. Brazing was certainly practised in the late Middle Ages and may be difficult to distinguish from later repair.

The commonest stabilising repair is a patch riveted over or inside a damaged area. Hundreds of objects show this treatment, including [ref_arm_1298] PDF [ref_arm_1328] PDF [ref_arm_1346] PDF [ref_arm_2334] PDF [ref_arm_3724] PDF. The date of such patches often remains uncertain.

Redaktionelle Hinweise · 1
  • „cannot be considered as genuine anymore“ wurde auf den nicht mehr unveränderten Zustand präzisiert: umfangreiche Eingriffe beseitigen nicht die historische Herkunft des erhaltenen Originalmaterials.
Originalwortlaut vergleichen
6.2.1 Modern alterations  



The extant armour parts often had been neglected throughout the preceding centuries and 



many were in a bad condition. Parts were lost or they had got separated and needed to get 



fixed again. Rust had covered the surfaces and the organic parts had fallen to  dust. As the 



conservation of the objects in their most original state is merely an invention of the times 



after World War II, earlier collectors and museums did often not care too much about the 



alteration of the objects. In the 19 th and the first half of  the 20 th century many broken or 



heavily corroded armour pieces were brought back to “beauty”. 318 In the 19 th century 



material produced in pre -industrial techniques as well as craftsmen capable of working by 



the old techniques were still available. Today it is therefore difficult to tell when a repairing 



or completion was made. 



Already by 1890 Wendelin Boeheim was of the opinion that fragmentary collectibles should 



not be completed. He suggested to better exhibit such objects with a good image showing a 



complete reconstruction. In his opinion the object had to remain unaltered as each 



completion would only further damage the original condition. To private collectors and 



dealers of arms and armour he gave the advice not to alter objects and to better buy a good  



cast replica from the “Stolbergsches Eisenwerk in Ilsenburg” or an electro -plated copy of 



“Haas in Vienna”.319  



Unfortunately, until today original armour is extensively repaired or completed – armour in 



public and in private possession. At least, modern alterations or completions carried out by 



public collections get usually documented today. For example the right elbow [ref_arm_492] 



was made in 1956 by the armourer of the Tower Armouries Theodore Egli.320 Nevertheless, 



some recent completions are very regrettable. Stephen V . Grancsay published an article on a 



poorly preserved helmet in his collection which apparently came from Rhodes. In close 



details, photographs and drawings he describes how the burred edges of the holes in the skull 



were cut straight and how 25 patches – cut from a genuine armour segment from Chalcis! – 



were embossed and subsequently welded into the holes. 321 It is certainly fair to ask, why



Grancsay did not simply order an entirely new reconstruction. An artifact so heavily altered 



cannot be considered as genuine anymore. Also some other restorers of the last century made 



use of modern welding techniques. For example parts of the brim at the helmet 



[ref_arm_1417] were reconstructed by welding patches to the old substance. Regrettable is 



the “repair” of the cutouts at the waist of the breastplate [ ref_arm_3696]. The genuine 



structure was mistakenly filled by plate segments.  



In the late 90ies of the last century Dieter Müller “filled” the corrosion craters on the plate -



surfaces of a genuine suit in his collection by electro -plating.322 This certainly also heavily 



altered the original condition, but at least the general shape of the plates was not changed by 



this restoration-method.  



Heavy restorations and completions are still realized today. Not only private collectors alter 



original objects to give them a “nicer” appearance, but also some museums still do this. Each 



museum has its restoration department or at least it cooperates with a restorer. Several 



examples of recent restoration work can be quoted. Especially archaeological objects often 



got stabilized by artificial resin [ ref_arm_1520] [ref_arm_3284]. The share of raisin at the 



helmet [ref_arm_1460] for example is certainly higher than the shar e of iron. For example 



the damaged paintings on the head piece of the Vienna helmet [ref_arm_1893] had recently 



been “completed”. The reinforcement plate for the forehead of the helmet [ ref_arm_1802] 



had been extended in the 1980ies. Small plates were riveted to the side ends of the plate. 



This is certainly an unnecessary “restoration” based on the complete misunderstanding of 



this helmet. In 2012 the detached visor of this helmet was found in the storage of the 



museum. Examinations by the author made clear that before its “restoration” – the detaching 



of the visor and the extension of the forehead reinforce – this helmet was in an absolutely 



genuine condition. Comparisons to sim ilar helmets support  this assumption and allow the 



reconstruction of the original appearance [ref_arm_1706] [ref_arm_1718] [ref_arm_1735].  



Several items show repair that might have corrected a mistake that already occurred in the 



production process. For example the helmet [ ref_arm_1702] on the top of the skull shows 



on several locations copper -colored soldering at cracks in the surface that could have 



occurred when the skull got embossed. Similar repair is visible interiorly at the helmet 



[ref_arm_1713]. The copper-colored solder is also found at presumable reproductions like 



[ref_arm_1510] and is therefore not necessarily late -medieval. Hard -solder has certainly 



been used in the late Middle Ag es and can probably not easily be differed from modern 



repair. The most common stabilizing technique is the riveting of a patch of plate into or onto 



the problematic location. Hundreds of objects show such repair [ ref_arm_1298] 



[ref_arm_1328] [ref_arm_1346] [ref_arm_2334] [ref_arm_3724]. Also here it often cannot 



be said with certainty at what time the patch was applied.
S. 176 · Sprachlich überarbeitet · Entwurf

6.2.2 Historic reuse of armour

An obvious question about the surviving stock is: where is the rest? Millions of armour objects must once have existed across European battlefields, but most cannot be traced. Some may remain beneath ruined castles, in former moats or on battlefields. Much metal was certainly reused for other purposes. Only a small proportion survived above ground. Among those survivors, some show clear evidence of reuse or conversion into more fashionable forms. The following examples illustrate these changes.

Originalwortlaut vergleichen
6.2.2 Historical recycling of armour parts 



One important question on the existing stock of ancient armour is: Where is the rest? In the 



times when armour was used on all European battlefields millions of armour parts must have 



existed. The fate of most of them cannot be retraced. A large number might still remain 



undiscovered under the ruins of castles, the moats outside city walls and the ancient 



battlefields. The material of another large group was certainly reused for the making of non-



armour items. A small number of items were preserved above ground. Within the stock of 



extant armour few parts are found that were obviously reused. Some older types were turned 



into a more fashionable model. In the following chapter a few examples of such alterations 



will be introduced.
S. 177 · Sprachlich überarbeitet · Entwurf

6.2.2.1 Reuse for objects other than armour

Fifteenth- and sixteenth-century castle and church doors were often reinforced with metal. One example incorporates breastplates hammered flat [ref_ill_art_5295] PDF. A breastplate of about 1580 became a keyhole plate [ref_ill_art_5201] PDF, a kettle hat became a cooking vessel [ref_arm_1378] PDF, and an etched sixteenth-century breastplate became part of a Baroque lock’s backplate [ref_ill_art_5307] PDF. Many further examples exist.

Originalwortlaut vergleichen
6.2.2.1 Reusing the plate for non-armour items 



In the 15th and 16th century doors in castles and churches often got reinforced by metal plates. 



One example was reinforced by breastplates that were hammered flat [ ref_ill_art_5295]. 



Another breastplate of about 1580 was turned into a keyhole plate [ref_ill_art_5201]. A kettle 



hat has been recycled into a cooking kettle [ ref_arm_1378]. An etched 16 th century 



breastplate ended up as part of the base plate of a baroque lock [ref_ill_art_5307]. There are 



many more such examples to be found.
S. 177 · Sprachlich überarbeitet · Entwurf

6.2.2.2 Updating armour to changing fashions

Armour could remain in use for long periods, with its form or decoration altered to suit changing tastes. In the sixteenth or seventeenth century, the upward-pointing centre of the abdominal plate of [ref_arm_3946] PDF was cut away. Curved ridges on both torso plates were hammered flat, and the surface blackened. Traces of the ridges remain visible inside and out. Around the mid-sixteenth century, [ref_arm_3684] PDF was painted in black and white stripes to imitate contemporary “black-and-white” armour.

Around 1450, the late fourteenth-century Type V helmet [ref_arm_2058] PDF was updated within the same type. Its ring-armour collar studs were removed, the face opening enlarged and the lower edge turned. Its face guard was probably already missing, leaving the face open.

Late fourteenth-century Type IV helmets [ref_arm_1653] PDF [ref_arm_1655] PDF [ref_arm_1658] PDF [ref_arm_1768] PDF were converted to Type VIII in the first half of the fifteenth century by adding large shoulder-covering plates. Type IV [ref_arm_1562] PDF lost its visor and acquired a forehead peak in mid-sixteenth-century fashion.

The forehead reinforcement of [ref_arm_1754] PDF is probably later. Originally it likely resembled [ref_arm_1752] PDF, and both probably had face defences. Two former attachment holes above each ear are now closed with rivets.

Historic alterations and later collecting interventions both complicate reconstruction of original appearances. It is therefore essential to distinguish changes made during use from additions made in the past two centuries.

Redaktionelle Hinweise · 1
  • Der letzte Originalsaz schreibt pauschal alle beschriebenen Vorgänge den letzten 200 Jahren zu, obwohl zuvor mittelalterliche und frühneuzeitliche Umarbeitungen genannt werden. Die zeitlichen Gruppen sind deshalb ausdrücklich getrennt.
Originalwortlaut vergleichen
6.2.2.2 Giving armour a fashionable upgrade 



Many armour parts were used for a long time, the shape and the decoration of some of them 



in later times got adapted to the latest fashion. At some time in the 16 th or 17th century the 



central upwards pointing edge of the abdomen -plate at [ref_arm_3946] was cut off and the 



curved ridges at the abdomen and the thorax -plates were flattened by hammer to give the 



item a plain appearance in the taste of the time. The surface was simply blackened after these 



alterations had been carried out. The lines of the former ridges are still visible in - and 



exteriorly. The breastplate [ ref_arm_3684] by the mid-16th century was painted by black -



and-white stripes to imitate a c ontemporary “black -and-white” breastplate. The type -V 



helmet of the late 14 th century [ref_arm_2058] by 1450 was turned into a more fashionable 



version of the same type. The studs that once held the ring-armour collar were taken off, the 



face-cutout was enlarged and the lower edge was turned. The face -guard was probably 



already missing and the helmet was used with an open face -cutout. The helmets 



[ref_arm_1653] [ ref_arm_1655] [ ref_arm_1658] [ ref_arm_1768] are actually type -IV 



helmets of the late 14 th century, in the first half of the 15 th century they were turned into 



helmets of type-VIII by the application of large shoulder-covering plates at the lower edge. 



The type-IV helmet [ref_arm_1562] was stripped off his visor and a fall in the fashion of the 



mid 16th century was attached to the forehead. On the helmet [ref_arm_1754] the forehead 



reinforce is most likely a later addition. This helmet probably looked similar  to 



[ref_arm_1752] and both of them had a face protection attached. At each side of the skull, 



above the ears there are two former holes visible, now closed by rivets.  



All the aforesaid activities throughout the last 200 years have altered the history of genuine 



armour. For the reconstruction of the genuine picture it is therefore indispensable to try to 



scientifically divide out what has been added to the extant examples in the two past centuries.
S. 177 · Sprachlich überarbeitet · Entwurf

6.3 Earlier approaches to authenticity

The following discussion examines earlier methods of assessing authenticity and the limits of the evidence on which they rely.

Originalwortlaut vergleichen
6.3 Preceding preoccupations with the general topic of authenticity
S. 177–182 · Sprachlich überarbeitet · Entwurf

6.3.1 Approaches of archaeologists, art historians and connoisseurs

For two centuries, dealers, collectors and curators have sought reliable ways to assess armour’s authenticity. Their advisers generally drew on experience gained from handling hundreds of objects. The range of evidence involved makes the task comparable to forensic investigation. This section considers approaches preceding, or distinct from, laboratory analysis.

When many private collections were formed, little armour scholarship existed. Collectors therefore researched their own holdings, examining historic depictions to determine whether unusual forms could have existed. Several early authors, especially British collectors,323 produced work of sufficient quality to merit recognition as scholars, even without formal archaeological or art-historical training. Yet they did not publish systematic accounts of their authentication criteria.

Wendelin Boeheim, curator of Vienna’s Hofjagd- und Rüstkammer, was probably the first to devote a chapter to the problem in his 1890 “Handbuch der Waffenkunde”.324 Neither a collector nor formally trained in archaeology or art history, he nevertheless had considerable experience. His guidance is broadly plausible but generalised, without references to specific objects or illustrations of the features discussed.

Boeheim argued that inexperienced collectors were vulnerable to dishonest dealers, while many dealers had acquired substantial expertise through handling objects. His first proposed test concerned price: if an object could not be made anew for the asking price, it was probably genuine. A forger, he reasoned, sought a greater return than honest manufacture offered. Prices substantially above the cost of new work therefore warranted closer investigation.

He then asked whether form, decoration, inscriptions and heraldry matched the proposed date, especially where an object was attributed to a person or event. Such features could have been added to genuine armour to increase its value. Inscriptions should reflect contemporary language; he believed forgers, lacking philological and historical knowledge, would make errors in mottoes or aphorisms.

Boeheim also thought modern work unintentionally more regular than historic manufacture. Forging sheet and then shaping it should, he argued, leave internal hammer marks, whereas rolled sheet would show elongated grooves crossing them. Breastplates were supposedly unprofitable to reproduce because they should appear forged from a billet rather than merely shaped from sheet. A sixteenth-century helmet with a high medial ridge, made from one plate, would be similarly uneconomical. He therefore envisaged many composite suits combining genuine breastplates and helmets with reproduced components, distinguishable by differences in the metal’s colour.

Even convincing objects might, he suggested, be exposed by machine-made rather than hand-forged rivets. He described apparently flawless Paris armour whose helmets and breastplates were made from what he probably meant as rolled sheet: making them by older methods at full thickness would allegedly have been uneconomic at any selling price. Seams joining two skull halves could be detected inside.

Textiles and leather offered further tests. A knowledgeable observer could supposedly recognise old velvet by its colour and distinguish modern alum-tanned leather. Rust was not conclusive, since genuine iron could remain uncorroded and forgers could artificially corrode new work. He described recent rust as bright red and easily rubbed off. Damage in implausible positions, such as recesses unlikely to receive blows or falls, might have been deliberately introduced.

Finally, a forger might enhance genuine armour with new embossing or decoration. Boeheim believed modern work, especially etching, could not precisely reproduce historic technique and style. He stated that this trade supported several workers in Paris, Nuremberg, Munich and Stuttgart, with poorer work produced in Venice.325

These observations reflect experience but offer little practical help to a reader lacking comparable objects. Even an experienced reader must question several assumptions. The price test is particularly doubtful. In the introduction to his early twentieth-century reproduction catalogue, Ernst Schmidt wrote:

“The purpose of this endeavor [making reproductions] is to enable the 



amateur of these familiar decorative objects to enjoy them at reasonable 



prices compared to the cost of originals.”
Schmidt, reproduced in Mowbray (1967), p. 13. 326

Reproductions and forgeries were therefore not necessarily expensive around 1910. Boeheim also overlooked the possibility of mistakes in genuine inscriptions. Historic craftspeople could be illiterate, and copied inscriptions sometimes altered, omitted or exchanged letters, accidentally or deliberately.327

Nor is there evidence that nineteenth-century workers were invariably more regular than medieval makers. Both periods included skilled and less skilled practitioners. Although old sheet was probably always forged, it is unproven that all nineteenth-century rolled sheet retained grooves. Surface quality varied, and a determined forger could remove grooves by grinding or polishing, or heat and hammer the sheet to create expected marks. Machine-hammered sheet also remained available locally in Boeheim’s time.

Historic forged sheets on doors [ref_ill_art_5389] PDF and iron chests further complicate the hammer-mark criterion. Hundreds of unembossed examples lack small marks because large water-powered hammers produced relatively flat surfaces. Boeheim did not define the differences between handmade and machine-made rivets, and hand production may still have continued locally in the late nineteenth century.328 Leather and textiles are weak indicators too, since genuine armour can have later replacements.

Baron Potier subsequently proposed similar criteria: rust colour and extent, hammer marks, machine traces and ignorance of older methods.329 He also challenged Boeheim’s judgement, identifying a supposedly genuine late fifteenth-century suit published by Boeheim330 as Winkelmayer’s work.331

Sir Guy Francis Laking was the next author to discuss the problem and the first to illustrate the objects concerned. Many judgements remained intuitive rather than fully reasoned. He described Grimshaw’s work as poorly made and unusable, sometimes showing rolling marks. His further criticism included the following historically derogatory comparison:

“The rivets were often not more than round-headed nails; the edges of 



the plate seem to have been cut with shears; while such attempts at 



decoration as are found might have been made by a savage from Central 



Africa.”
Laking, as quoted in the dissertation.

Why a domed rivet should not resemble a domed nail is unclear. Nor does Laking explain why medieval armourers would not have cut sheet with shears, or what alternative they would have used.332 In most respects his criteria remain as general as Boeheim’s.

In 1914, the MET installed what was probably the first permanent armour display devoted exclusively to reproductions and forgeries. Grancsay described it in 1932.333 It aimed to train students’ eyes, sharpen their judgement and encourage appreciation of genuine armour by examining the shortcomings of reproductions. He also offered unusually direct access:

…when the student wishes to examine an object more closely, it will be 



removed from the case for his convenience.”
Grancsay (1932).

This valuable approach was exceptional. The display was later dismantled.334 Grancsay’s article otherwise largely repeats Boeheim’s criteria, sometimes rejecting objects because their form seemed too poor to be authentic. He regretted lacking space to explain in detail how his department distinguished original components from restoration, acknowledging that every object posed a new problem.335 He nevertheless drew an extended distinction between connoisseurs and archaeologists:336

“There are two ways of testing authenticity – that of the connoisseur and 



that of the archaeologist. The connoisseur deals with impressions and 



intuitions; the archaeologist proceeds by the examination and analysis of 



form, construction, decoration, metal and patination. Each object is 



studied from the craftsman’ s point of view; only in this way is it possible 



to understand the practical purpose of every rivet, buckle, perforation, 



and turning pin. Because of the many separate elements, sometimes over 



two hundred, comprising a suit of armour , it is clear that this study is 



mainly the field of archaeologists rather than that of the connoisseur . The 



details which make up the structure of armour are too numerous for it to 



be possible, except in obvious cases, to authenticate or condemn an 



object in a flash of intuition. The connoisseur’ s judgment is 



unconsciously affected by associating and comparing the object under 



examination with similar objects known to him. Thus the connoisseur 



might condemn a piece because in his experience he has not seen 



nothing like it, or because, having been restored in part or having 



additions made to it, it no longer measured up to his ideals.
Grancsay (1932), p. 47. 337

Grancsay’s “connoisseurs” were chiefly private collectors whose decisions, in his view, rested on intuition rather than articulated evidence. Yet an unfamiliar or suspicious form cannot alone prove forgery: scholars too may lack comparable genuine examples, either because none is known or because none survives. His demand for detailed examination before judgement is nevertheless sound.

The most comprehensive earlier discussion is Hans Schedelmann’s five-part series in the “Zeitschrift für Waffen- und Kostümkunde”.338 Its documentation of information and illustrations is unfortunately sparse. Schedelmann called for continuing comparison with other material, emphasised provenance and proposed a central register of known forgeries in a major museum.

Some of his criteria are more detailed than those of his predecessors. He regarded delamination caused by older metallurgical processes as proof of authenticity, while admitting that genuine objects need not show it. He believed a forger would never obtain or reproduce old material because doing so would be unprofitable. He distinguished delamination parallel to the surface from cracks cutting through the sheet at roughly right angles.

Like Boeheim, Schedelmann assumed modern workers could not match earlier skill and that poor proportions would reveal reproductions. He claimed modern makers welded skulls from two plates and made roped edges by turning sheet around wire and filing the pattern.339 Yet genuine roping was not always embossed [ref_arm_1128] PDF, and hundreds of historic turned edges contain wire [ref_arm_1726] PDF [ref_arm_2076] PDF. No comparably comprehensive study had followed his articles by the time of this dissertation.

A scholarly assessment should rest on explicit evidence and careful judgement. Experts ought to explain why they regard an object as original or reproduced; detailed description of human-made objects is central to their work. Neither Grancsay nor his predecessors published enough reasoned explanation. Without transparent arguments, a non-specialist cannot distinguish an academic judgement from the intuition Grancsay criticised. For much surviving plate armour, uncertainty should be acknowledged rather than concealed.

Later sections examine selected published assessments of particular objects. Before those cases, the metallurgy of armour production must be introduced to explain the range of available approaches.

Redaktionelle Hinweise · 2
  • Historische wertende und rassistische Formulierungen bleiben ausschließlich als kenntlich gemachter Quellenwortlaut erhalten, nicht als Sprache der Neubearbeitung.
  • Die Methoden werden als Positionen der jeweiligen Autoren wiedergegeben; Preis, Oberflächenbild oder einzelne Fertigungsmerkmale werden nicht als gesicherte alleinige Echtheitstests übernommen.
Originalwortlaut vergleichen
6.3.1 Archaeologist’s, art historian’s and connoisseur’s approaches 



Throughout the last two hundred years , all persons who intended to buy armour or to 



examine it for scholarly purpose were interested in methods of authenticity-testing: dealers, 



private collectors and museum curators. The consulted experts usually had gathered their 



experience by the handling of hundreds of objects. Di fferent information-classes had to be 



attended when the authenticity of a certain armour part was in question. The methods used 



for approaching the problem remind on those of forensic sciences. In the following some 



preceding, non-natural-scientific approaches will be introduced.  



By the times many private collections were assembled, not much had yet been written about 



ancient armour and thus collectors had to do research about their collectibles by themselves. 



For the authenticity question of unique examples it was necessary to study the historic al 



depictions of armour – to find out if such an object might have really existed.



Some of the early scholars publishing good quality articles on antique arms and armour – 



most of them British – were also collectors.323 These men – even if some of them had never 



academically studied archae ology or art history – due to the quality of their work can be 



considered as academic scholars. Despite their experience , no collector published a word 



that would describe the factors that need to be considered when the authenticity of armour 



should be tested. By 1890 the custos of the Vienna Hofjagd - und Rüstkammer Wendelin 



Boeheim – himself being neither a collector nor an  archaeologist or art historian – in his 



“Handbuch der Waffenkunde” was probably the first to dedicate a chapter to this problematic 



aspect of any kind of preoccupation with arms and armour.324 Unfortunately his explanations 



are of a generalizing nature and they are not supported by any references to particularly 



concerned artifacts. He included no images of the features described. Nevertheless, Boeheim 



has been an experienced scholar. His suggestions are basically plausible and therefore the 



passages in his book dealing with armour will be summarized in the following paragraphs.  



Boeheim argued that private collectors did often not have enough experience for not being 



tricked by criminal dealers. On the other hand many dealers – even though no academics – 



had become specialists in the classification of arms and armour, due to the many objects they 



handled throughout the years. As a simple primary indicator for the authenticity-testing of a 



certain item he set  up the following formula concerning the price: If a n offered item can 



currently not be produced for the named price it is m ost likely genuine. He justified  his 



argument by the assumption that a potential forger intended to earn much more than he would 



by selling hones t work -pieces. Only if a price wa s much  higher than it would be for 



nowadays’ work , the potential buyer has to be careful and to further test an item’s 



authenticity. Boeheim then names several object-features that need to be examined: Does the 



general shape fit to the presumed date? This would be very important if the offered item 



allegedly can be attributed to certain historical happenings or persons. Do the decorations, 



inscriptions, coats -of-arms in design and techniques apply t o the presumed date? He 



mentioned that even at genuine items the aforesaid features could have been applied in 



modern times to raise their value. Inscriptions and verses would reflect the expression-style 



of their own time. Boeheim presumed that here forgers  would easily make mistakes in the 



application of aphorisms or mottoes, as they were usually no academic philologists or culture 



historians. Concerning the general shape Boeheim argued that the forger usually worked 



“accidentally” more regular than the old craftsman. The. Boeheim presumed that the making 



of plate-sheet by hammer-forging and the subsequent embossing of the plate must have left 



interior hammer-marks. Modern rolled plate-sheet would show elongated grooves crossing  



such hammer-marks. He considered the breastplate as the least profitable part to be forged, 



as it should not appear as being made of plate but rather forged from the billet. Forging a 



16th century style helmet with its high medial ridge from one single plate -sheet would just 



as well be not profitable. Therefore, many suits of armour actually would consist of a genuine 



helmet and breastplate, completed by reproduced parts. These completions could easily be 



detected by a comparison of the colors of the iron. Even if all the features appeared correct, 



the rivets could unmask an item as a forgery. The old ones were made by hand and the 



modern ones are made by machines. He mentioned armour allegedly produced in Paris that 



– judging by a superficial look – appeared without blemish, but the helmets and breastplates 



were made of plate-sheet (he probably means “rolled” plate). No matter how expensive they 



were sold, if they would have been made in the old techniques and in the full thickness of 



the material it would be too unprofitable to prod uce them today. He also thought  that the



welding seam of helmet skulls made of two plates can be detected interiorly. If the testing of 



all features did still not unmask the item as a forgery, applications like velvet and leather 



would do. The connoisseur would recognize the color of old velvet and the modern alum -



tanned leather appears different from the old leather. The rust on iron can be considered as a 



sign of age. The forgers would use this feature to trick the naive buyer who does not know 



that this is no indicator, as there are genuine iron artifacts that show no trace of rust. Boeheim 



allegedly knew that forgers used different methods to corrode their products. The “young” 



rust would be of bright red color and could be wiped off with the finger. Also damages – be 



them deriving from fighting or from falling to the ground – on armour were imitated by the 



forger to make his products less suspected. Where it may appear illogical that such damages 



could derive from a natural cause, e. g. if they were found in the cavities of the general shape, 



they had possibly been applied on purpose. To trick the potential buyer, the faker would often 



take an old armour part and make it more valuable by embossing and decorating it with 



“fresh” ornaments. These ornaments could easily be distinguished from the “old” as the 



modern worker was not capable of working by exactly the same technique and style. 



Especially etchings would not be of the same quality. Such alterat ions on old pieces, 



Boeheim said, fed several people in Paris,  Nuremberg, Munich and Stuttgart. Poor quality 



work of this kind was made in V enice. 325  



Boeheim’s arguments are based on a good deal of personal experience. Nevertheless, a 



reader who has never seen a piece comparable to one currently in question is left h elpless 



with his guidelines. Also for the experienced, Boeheim’s arguments do not remain without 



questions. His argument concerning the price is a doubtful factor. By the early 20 th century 



in the foreword to his catalogue of reproductions Ernst Schmidt said:  



“The purpose of this endeavor [making reproductions] is to enable the 



amateur of these familiar decorative objects to enjoy them at reasonable 



prices compared to the cost of originals.”326  



This shows that the prices for reproductions or forgeries – at least about 1910 when the 



catalogue was published – were not necessarily high. When suggesting that the forgers of 



his days would easily make mistakes in the application of “aphorisms or mottoes” Boeheim 



forgets that the craftsmen of old might also have made mistakes and that some of them might 



even have been analphabets. Also the masters of old copied inscriptions from successful 



products, but they often altered, exchanged or omitted some letters by chance or in 



purpose.327 Furthermore, there is no evidence that all 19 th century craftsmen were working 



“more regular” than the ancient armourers. In both times high or little skilled workers might 



have made armour. While he is probably correct in saying that all old plate had been made 



by forging, it is an unprov en assumption that all 19 th century rolled plate showed grooves. 



This was certainly a matter of quality and a craftsman determined to sell his product as 



genuine could easily grind or polish such grooves off the starting material. It would also not 



be a pr oblem at all to heat a rolled plate and to treat it with the hammer to reveal the 



“expected” hammer-marks. Furthermore, even in Boeheim’s days plate sheet was probably 



locally still produced with a machine -hammer (see below). Another fact leaves doubts on 



Boeheim’s assumption concerning the small hammer -marks: Hundreds of un -embossed 



hammer-made iron plates are found as reinforces on old doors [ ref_ill_art_5389] or on old



iron chests. None of them show small hammer -marks, as they were made by huge 



waterpowered hammers that drove the surface more or less plane. On the rivets Boeheim 



omits the definition of the differences between handmade and machine -made examples. 



Furthermore, by the end of the 19th century rivets were maybe locally still made by hand.328 



The leather and the fabric parts are also a weak indicator for the authenticity of an object 



only, as also on genuine items they had possibly been exchanged in younger times. 



A few years after Boeheim, Baron Potier had published another essay on the methodology 



for detecting forgeries. His arguments we re much the same like Boeheim’s: t he color and 



intensity of rust, hammer-marks, the traceable use of machines and the general ignorance of 



the old techniques. 329 It was Potier who uncovered that even Boeheim’s judg ment was not 



without blemish: Boeheim  had described a late 15 th century suit of armour 330 as genuine, 



while – according to Potier – it was made by the forger Winkelmayer of Vienna.331  



The next scholar who published some notes on the problem of authenticity was Sir Guy 



Francis Laking. He wa s the first to illustrate his findings by main views of the concerned 



objects. Most of his arguments we re of an intuitive nature and are not  based on profound 



reasons. Some examples will be quoted: He described the items made by the mid-19th century 



forger Grimshaw as being made of the poorest craftsmanship and impossible to be actually 



used. At some pieces the “peculiar markings left by the rollers” on rolled plate were visible. 



“The rivets were often not more than round-headed nails; the edges of 



the plate seem to have been cut with shears; while such attempts at 



decoration as are found might have been made by a savage from Central 



Africa.”332  



It is not understandable why a dome -headed rivet should not look like a dome -headed nail. 



Laking also does not say why the ancient armourers should not have used shears for cutting 



the plate or what they should have used instead . Furthermore, in nearly all other points his 



argumentation remains as general as Boeheim’s.  



In 1914 the first exhibition to the problem of authenticity, showing exclusively reproductions 



and forgeries, was permanently installed in the armour galleries of the MET. At this time this 



was probably the only conscious display of such objects in the entire world. In 1932 Stephen 



V . Grancsay wrote a short article on this exhibition.333 The intention of this installation was 



to offer “the student a splendid opportunity to train his eye and to improve his taste, and this 



training is the more essential as greater trouble has been taken to deceive than to deceit. By 



pointing out defects in forgeries we emphasize the skill of the ancient armourer and thereby 



encourage an appreciation of authentic armour”. Stephen V . Grancsay even offers: “ 



…when the student wishes to examine an object more closely, it will be 



removed from the case for his convenience.”



This attitude is a noble, but singular one. At some date this ensemble of forgeries has been 



taken off display.334  



Grancsay in his article on this exhibition mentions much the same “features to look for” that 



Boeheim had promoted before him. He superficially classifies some armour parts as 



reproductions, allegedly as the form is too poor to be authentic. Later on he regrets that there 



is too little space in the article to “describe the methods used by the members of the 



department in distinguishing genuine elements from restorations, obviously the most 



important part of a lesson in detecting forgeries. Each object presents a new problem, for 



the intriguing subject of forgeries is not an exact science.” 335 Anyway, there has been still 



enough space for Grancsay to debase a certain group of persons also preoccupied with the 



topic:  



“There are two ways of testing authenticity – that of the connoisseur and 



that of the archaeologist336. The connoisseur deals with impressions and 



intuitions; the archaeologist proceeds by the examination and analysis of 



form, construction, decoration, metal and patination. Each object is 



studied from the craftsman’ s point of view; only in this way is it possible 



to understand the practical purpose of every rivet, buckle, perforation, 



and turning pin. Because of the many separate elements, sometimes over 



two hundred, comprising a suit of armour , it is clear that this study is 



mainly the field of archaeologists rather than that of the connoisseur . The 



details which make up the structure of armour are too numerous for it to 



be possible, except in obvious cases, to authenticate or condemn an 



object in a flash of intuition. The connoisseur’ s judgment is 



unconsciously affected by associating and comparing the object under 



examination with similar objects known to him. Thus the connoisseur 



might condemn a piece because in his experience he has not seen 



nothing like it, or because, having been restored in part or having 



additions made to it, it no longer measured up to his ideals.337” 



The “connoisseurs” for Grancsay are the many private collectors that – to his opinion – do 



not substitute their conclusions on the authenticity question with reasonable arguments and 



decide only by “gut feelings”. Anyway, a suspicious form cannot be the only evidence  for 



an item to be “faked”. What if the scholar – Grancsay blames only the connoisseur – just has 



not seen a genuine object of the same form, as none is known or none has survived? 



However, he is right in demanding that especially art historians and archaeologists should 



study all the details of an object before judgments are delivered. 



One further preceding discussion of the subject should be summarized. Certainly the most 



comprehensive study of the authenticity problem was published by Hans Schedelmann in 5 



articles in the Zeitschrift für Waffen- und Kostümkunde.338 Unfortunately, the references to



most of the information and images included are more than scanty. Schedelmann was the 



first to demand “a permanent consulting of comparable material” whenever authenticity is 



in question and he was the first to emphasize the s ignificance of an item’s provenance. He 



further suggests the establishing of a central register of known forgeries in one of the large 



museums of arms and armour. Schedelmann then enters a discussion of certain criterion that 



could tell about the authenticity of armour. While of course several suggestions are congruent 



with those of earlier writers on the subject, in a few cases his arguments are more detailed. 



Concerning the material he mentions that due to the old metallurgical processes the genuine 



material would delaminate. The observation of such a feature for Schedelmann is a clear 



proof of authenticity. But he has to admit that parts that do not show such signs can still be 



genuine. He is sure that a forger would never organize or reproduce old materi al as this 



would make his work unprofitable. Furthermore he warns to confuse simple material-cracks 



with such delaminations. Cracks would pass in a more or less 90 degree angle through the 



plate, while delaminations occur in parallel to the plate-surface. Concerning the techniques, 



Schedelmann – in parallel to Boeheim – assumes that the modern could never reach the skills 



of the old craftsmen and therefore poor proportions would easily unmask a forgery. The 



modern armourers would weld the helmet -skulls together from two plates. The roped turns 



would simply be made by turning them around a wire and then filing the roping. 339 He did 



obviously not know that also genuine roping was not always embossed [ref_arm_1128] and 



that hundreds of turned edges on extant armour have a wire inserted [ ref_arm_1726] 



[ref_arm_2076]. Since his articles no comprehensive studies on the problem of authenticity 



of armour have been published.  



An expertise worked out strictly by academic rules is distinguished by matter of fact and 



careful decisions. Experts should be able to put down into words why they decide for a 



specimen to be authenti c or reproduced. The detail description of images and sculptures – 



respectively all manmade artifacts – is their every day job. Grancsay and none of his 



colleagues published satisfyingly enough reasonable arguments. How should a lay recognize 



if an expertise is well-founded, if the art historian – like the connoisseur – does not make his 



considerations transparent? If an academic is not capable of doing so the quality of his 



statement cannot be distinguished from that of Grancsay’s connoisseur. Scholars sho uld 



better honestly permit that for the largest part of the extant plate armour a permanent 



uncertainty in the judgment on an item’s authenticity remains.  



The authenticity testing of some specific items has been described by some of the scholars 



named above. A few chosen examples will be introduced and discussed later in this  study. 



For the understanding of various possible approaches first the b asics of the metallurgy of 



armour production need to be generally described.

7 The metallurgy of armour production

S. 183 · Sprachlich überarbeitet · Entwurf

7 The metallurgy of armour production

Ironmaking methods developed over time and sometimes remained in use alongside one another. This chapter outlines the differences between historic and modern processes rather than attempting a complete technical account. John Verhoeven’s “Steel Metallurgy for the Non-Metallurgist” provides a useful introduction for non-specialists.340 The second and third parts of the chapter address sheet production and the material qualities available to armourers.

Originalwortlaut vergleichen
7 The metallurgy of armour production 



In different times different iron-production techniques were developed and used, sometimes 



in parallel. In the following the differences between various modern and ancient techniques 



will be described. The entire technological background cannot be provided by this study. For 



a deeper understanding John V erhoeven’s book “Steel metallurgy for the non -



metallurgist”340 can implicitly be regarded to all interested non -specialists. All knowledge 



necessary for the basic understanding of metallurgy can be found in this publication. The 



second and the third part of this chapter deal with the topic of plate-making and the different 



plate qualities used for making armour.
S. 183 · Sprachlich überarbeitet · Entwurf

7.1 Iron and steel production

Metallurgy encompasses a wide range of processes developed over roughly three millennia. A full account lies beyond this study. Wolfgang Piersig offers an accessible historical overview,341 while Frederick Overman’s mid-nineteenth-century work provides more detailed contemporary descriptions.342 The following sections outline the principal methods capable of producing material suitable for armour.

For the purposes of this discussion, the source distinguishes mechanically refined wrought iron from steel produced by later liquid-state processes. This is a distinction between production routes; historic armour can itself contain steel with sufficient carbon for hardening.

Redaktionelle Hinweise · 1
  • Das Original stellt „wrought-iron“ und „mild steel“ als umfassende Materialklassen gegenüber. Dies vermischt Herstellungsverfahren und Kohlenstoffgehalt. Die beabsichtigte prozessbezogene Gliederung wurde kenntlich gemacht; metallurgische Terminologie fachlich prüfen.
Originalwortlaut vergleichen
7.1 The production of iron and steel 



Metallurgy is a vast and eclectic field. V arious techniques for the production of iron-based 



material got developed throughout the last 3000 years. It is not possible to go into all details 



within the range of this study. An easy -to-understand overview of the history of iron and 



steel making is provided for example by Wolfgang Piersig.341 More detailed descriptions are 



found in a mid-19th century publication of Frederick Overman. 342 A general description of 



the major production processes for the making of material that could be used for armour will 



be summarized in the following.  



Armour can be made of basically two different kinds of material: wrought-iron or mild steel.
S. 183 · Sprachlich überarbeitet · Entwurf

7.1.1 Wrought-iron production

Here, “wrought iron” denotes iron-based material consolidated and refined through mechanical working. Different furnace designs produced two broad starting materials. Cast iron contains about 4% carbon, making it brittle when cold but lowering its melting temperature to around 1,200 °C.

Lower-temperature furnaces produced a bloom, probably the earliest form of ironmaking. Its carbon content is lower than that of cast iron, and the iron does not melt completely because the furnace does not reach the temperature required for the low-carbon metal, over 1,500 °C. The result is generally a heterogeneous, sponge-like mass with local variations in carbon [ref_ill_art_5384] PDF, cavities, slag and sometimes charcoal inclusions. Unlike cast iron, this bloomery product no longer had a significant industrial role at the time of the study.

From at least the fourteenth century, central European metalworkers processed both cast and bloomery iron into improved, forgeable stock. Neither furnace product could be used directly as armour sheet. Both required refining, including mechanical work to produce a more consolidated and homogeneous material. The following sections consider the direct and indirect routes in turn.

Redaktionelle Hinweise · 1
  • Temperaturen und Kohlenstoffangaben sind die vereinfachten Größenordnungen des Originals, keine allgemein gültigen Grenzwerte für sämtliche Legierungen.
Originalwortlaut vergleichen
7.1.1 Wrought-iron production 



The term wrought -iron describes all iron -based material that was refined with the help of 



mechanical force. Different methods for the refining were developed. Depending on the 



construction of ancient smelting -furnaces, two kinds of iron -based material could be 



revealed. One kind is the so called “cast-iron”. This material contains about 4% carbon which 



makes the cooled material very brittle but keeps its melting point very low at about 1200 0C.  



While “cast iron” is still produced industrially today, the following kind of material is not 



industrially used anymore. It is the product of a furnace operating at lower temperatures only 



and probably the oldest technique of iron making. The revealed material – called “bloom” – 



contains less carbon than  the cast -iron (<4%). The iron never melted completely as the 



furnaces did not reach the necessary temperature of more than 1500 0C. The product is 



usually a heterogeneous sponge -like block of iron with locally higher carbon content 



[ref_ill_art_5384]. Inside the bloom hollow spaces and occasionally inclusions of charcoal 



and slag are to be found.  



At least since the 14th century the central European metallurgists processed both – cast- and 



bloomery-iron – to reveal forgeable material of increased quality for various applications. 



Both materials cannot be used directly for the production of armour plate. They first need to 



be refined by different techniques. The old refining techniques required a certain amount of 



mechanical labor to reach a more or less homogeneous quality of the material – no matter if 



they started with the cast - or the bloomery -iron. In the following , first the refining of 



bloomery-iron and subsequently the refining of cast-iron will be summarized.
S. 184 · Sprachlich überarbeitet · Entwurf

7.1.1.1 Refining bloomery iron: the direct process

I filmed a specialist demonstrating the direct process [ref_vid_dir]. A bloom produced in a Japanese tatara furnace was broken into pieces and heated to white heat in a forge. Hammering consolidated the material, expelled some semi-liquid slag and crushed or burned away charcoal inclusions [ref_ill_art_5385] PDF.

To clean and homogenise it further, the consolidated material was cut or broken into smaller pieces. Several flattened pieces were stacked [ref_ill_art_5386] PDF, reheated and forge-welded. A powdered flux, such as quartz sand or borax (Na₂B₄O₇·10H₂O), aided welding. Repeated heating and forging expelled more inclusions. At intervals, the billet was divided, restacked and welded again.

The repeated redistribution resembles mixing ingredients into dough. At high temperature, diffusion also helps redistribute elements through the metal. Greater working and longer heating tend to increase homogeneity, although not all non-metallic inclusions can be removed. Weld interfaces and elongated inclusions or defects can leave a layered or banded internal structure [ref_ill_art_5387] PDF. Charles describes one mechanism:

[…] the repeated piling and forging […] leads to surface oxidation and 



local enrichment in more noble elements such as nickel and copper , 



which becomes incorporated as extended solute bands in the final ferrite 



structure.
Charles (1998), p. 497. 343

The duration of this process’s use in Europe is uncertain, but it continued locally until at least the late nineteenth century. Traditional Japanese swordsmiths likewise refine their working material, tamahagane, through a direct-process tradition.

Originalwortlaut vergleichen
7.1.1.1 The refining of bloomery iron (direct process) 



The author had the chance to film a specialist for the direct iron -making process at work 



[ref_vid_dir]. For the refining of bloomery -iron a bloom made in a Japanese fu rnace (Jap. 



Tatara) was first broken into pieces. These were subsequently white -heated in a smith’s 



hearth. By hammer-forging the material was densified, some of the semi-liquid slag splashed 



out of the volume and included charcoal pieces burned off or got battered to dust 



[ref_ill_art_5385]. To further clean the material and to homogenize the chemical 



composition, the densified bloom was broken or cut into smaller segments. Several of such 



plate-like pieces were piled together [ ref_ill_art_5386], white-heated and welded together 



by forging. To a llow the pie ces to join,  it was necessary to dust the heated pack with a 



powdered welding flux like quartz sand or borax (Na2B4O7x10H2O). Repeated white-heating 



and forging further drove out remaining inclusions. After a certain refining stage, the volume 



was broken in two pieces that again were piled and forge -welded. Similar to the dispersing 



of bakery -ingredients for obtaining a  homogeneous dough , the “ingredients” in the iron 



block would homogenize with the processing of the work. Furthermore, inside the white-hot 



material the elements can move (diffuse) to a certain extent. The chemical components in 



iron tend to spread equally throu ghout the volume. Depending on the amount of repeated 



heating and the time the volume was kept white - or red- hot the substance would become 



more and more homogeneous. It is likely that not all non -metallic inclusions could be 



removed by this process. Due to the laminar welding seams and the extension of inclusions 



and defects, the material is expected to show an interior layered  or band  structure 



[ref_ill_art_5387]. Charles describes the formation of this structure:  



[…] the repeated piling and forging […] leads to surface oxidation and 



local enrichment in more noble elements such as nickel and copper , 



which becomes incorporated as extended solute bands in the final ferrite 



structure.343  



It is not clear how long this method was used in Europe, but it was certainly locally still 



exercised until the end of the 19th century. For example in Japan the traditional sword-smiths 



still produce their working-material by a direct refining process (Jap. Tamahagane).
S. 184–185 · Sprachlich überarbeitet · Entwurf

7.1.1.2 The indirect process

Cast iron is comparatively homogeneous but unsuitable for applications requiring substantial flexibility. Reducing its carbon content makes it forgeable. Metallurgists were attempting this conversion by the fourteenth century. Before the nineteenth century, central European furnaces could not readily maintain both an oxidising atmosphere and a fully liquid charge as declining carbon content raised its melting temperature.

Older finery processes melted cast iron at around 1,200 °C and exposed its surface to oxygen. Stirring or turning brought further portions into contact with the oxidising atmosphere. As carbon was removed, the metal gradually became pasty, trapping some slag. The refined mass was then removed and hammered into billets. Repeated folding and forge-welding expelled additional impurities and produced the required dimensions. Puddling, one indirect process, remained industrially important from the second half of the eighteenth into the early twentieth century.

Originalwortlaut vergleichen
7.1.1.2 The indirect process 



The cast-iron was widely homogeneous, but could only be used for the casting of artifacts 



that required no flexibility. For reaching similar deformation-properties to refined bloomery-



iron, the carbon content has to be reduced. Already by the 14th century metallurgists tried to 



convert cast-iron into forgeable iron or steel. In central Europe before the 19th century it was 



not possible to reach both necessary conditions at the same time: the oxidizing atmosphere 



inside the furnace together with the high temperatures to still keep the melt liquid while the 



carbon content was decreasing. The old cast -iron refining -techniques started with the 



smelting of cast -iron in special finery hearths (1200 0C ca.) that produced an oxidizing 



atmosphere on the surface of the melt. The charge needed to be moved by stirring or turning 



the melt from time to time to bring not yet de-carburized parts of the volume in contact with 



the oxygen. With the ongoing progress the melt slowly turned into a pasty mass. Parts of the 



slag occurring on the surface of the melt remained as inclusions within the volume. After the 



desired carbon content was reached, the revealed mass was taken off the furnace and forged 



under the hammer into billets. To drive out remaining impurities and to reveal certain billet-



dimensions it was necessary to fold and forge-weld the material. One indirect process of iron



making, the so called “puddle-method” was industrially used from the second half of the 18th 



until the early 20th century.
S. 185 · Sprachlich überarbeitet · Entwurf

7.1.2 Steelmaking by liquid-state processes

Later steelmaking methods reduce the carbon content of molten cast iron while maintaining sufficiently high temperatures to keep the refining metal liquid. The source gives 1,538 °C as the melting point of pure iron. Alloying additions can then produce the required properties. Unlike mechanically consolidated wrought iron, steel made in this way does not require repeated folding and welding to refine it.

Large-scale production by these methods developed comparatively recently. The Bessemer process was introduced into German production in 1861 but became widespread only from 1867.344 Phosphorus remained a problem in some early products. Further developments culminating in 1879 allowed much more effective phosphorus removal. The source associates these developments with Thomas and Martin; their respective processes require distinction.345 During the following forty years, newer methods largely displaced older wrought-iron production. The Linz–Donawitz process is one later example.

The resulting metal can be cast into billets or directly into profiles. Its comparatively homogeneous structure contrasts with the slag-bearing, repeatedly welded material discussed above.

Redaktionelle Hinweise · 2
  • Das Original setzt Sauerstoffeinblasen im Hochofen, Bessemer-, Thomas- und Martin-Verfahren zu stark gleich. Die Neubearbeitung beschreibt den gemeinsamen Grundgedanken ohne die falsche Apparatezuordnung; Verfahrensgeschichte und Jahreszahlen sind fachlich zu prüfen.
  • „Entirely homogeneous“ wurde zu einer vergleichenden Beschreibung präzisiert, da der Text keinen Nachweis absoluter Homogenität liefert.
Originalwortlaut vergleichen
7.1.2 Mild steel production 



The modern methods reduce the carbon-content of cast-iron by directly blowing oxygen into 



the melt inside the blast -furnace. The furnaces reach the temp erature to melt pure iron 



(15380C). To the revealed nearly pure liquid iron the corresponding elements necessary for 



desired material-properties are added. The technology for the mass-production of mild steel 



is comparatively young. In 1861 the so called “Bessemer -process” was first introduced in 



the German steel-production, but was widely used only from 1867 on.344 The steel produced 



by this technique was still of a comparatively low quality, as it contained too much 



phosphorus. In the years to follow, until 1879, Thomas and Martin developed the Bessemer-



process until nearly all phosphorus could be extracted from the melt. The introduction of this 



process marked the beginning of a totally new age in the production of iron and steel. Within 



the following forty years it would completely supersede the old wrought -iron-production 



techniques.345 Today a number of sophisticated techniques exist; a very popular one is the 



Linz-Donawitz-method. Mild steel is an entirely homogeneous material. It can either be cast 



directly into profiles or into billets. No mechanical refining is necessary.
S. 185–189 · Sprachlich überarbeitet · Entwurf

7.2 Making sheet metal

Armour sheet must be worked from billets or bars rather than cast directly to its final thin form. In the pre-industrial processes considered here, mechanically refined iron or steel supplied the necessary combination of ductility and strength.

Sheet suitable for armour can be produced by hot hammering or rolling. According to the research cited here, successful iron-sheet rolling was not established before the late seventeenth century,346 making its use for late medieval armour unlikely. By contrast, powered-hammer sheet production remains poorly studied. No detailed contemporary account of manufacture during the principal period of armour production has been identified.

Producing iron sheet demands considerable skill. Unlike many copper alloys,347 substantial spreading of iron billets requires high-temperature working; attempting the same deformation too cold can cause cracking. Neither Agricola348 nor Biringuccio349 describes the process. The earliest detailed descriptions identified here date to the late eighteenth century and have rarely been discussed in relation to armour. Only a few recent articles address historic sheet production,350 and just one reconstructs hammering from eighteenth- and nineteenth-century accounts.351 Much earlier armour scholarship therefore rests on inference rather than detailed technical evidence.

The claim that European smiths could not make breastplate-sized sheets before the fourteenth century is untenable. Around AD 600, a bell made in the German-speaking region used a steel sheet measuring 85 × 35 cm.352 This would be ample for a one-piece helmet or breastplate. The basic ability to make large iron sheets thus long preceded their extensive use in body protection.

Sheet can be made without machinery, but reducing a large billet to a thin sheet by hand requires much time and labour. Improvements in water-powered hammers may have contributed to the expansion of plate armour in the later fourteenth century. Water power was known in antiquity, declined during the early Middle Ages and probably expanded again from the eleventh century, driving mills, grinding wheels, bellows, hammers and later powder mills. Villard de Honnecourt’s thirteenth-century sketchbook includes an early water-powered saw [ref_ill_art_5299] PDF.

No rolling mills are documented for the period considered, whereas hundreds of German “Blechhämmer”, or plate-hammer works, are recorded. Conrad Eschenloer owned a “plechhammer” in Nuremberg in 1409,353 long before the city’s later prominence in armour-making. Their locations beside streams indicate waterwheel operation. One of the earliest hammer illustrations dates to the last quarter of the fifteenth century [ref_ill_art_5300] PDF; sixteenth- and seventeenth-century metallurgical books show further examples [ref_ill_art_5297] PDF. Different products required different hammer designs. Some European water-powered hammers still operated for educational demonstrations at the time of this study.

Carl J. B. Karsten’s “Handbuch der Eisenhüttenkunde” of 1816 contains one of the earliest detailed descriptions of hammering and rolling sheet.354 The following extract retains the dissertation author’s English translation, including its explanatory insertions:

To bring the iron into the shape of plate – i. e. extending it both by its 



length and by its width at the same time – it has to be heated to white-



heat and then to be forged by the beats of a hammer . Only in rare cases 



the plate can be finished in one heat. Usually the iron […] would get 



cold before the plate would be finished. Thus – to get to the desired 



dimensions – it is necessary to reheat the iron several times. The amount 



of pieces handled in one work shift is defined by the capacity of the 



facility for the heating of the iron, the power of the hammer , the 



dimensions of the work piece and the experience of the producer . […] 



A good plate has to have the same thickness at each spot and it has to be 



free of buckles, wrinkles and delaminations355, as these are not simply 



disfigurements but they could also become problematic for the further 



working of the plate. Furthermore a good plate has to withstand a 



repeated bending and should not be so brittle to crack throughout this 



testing. Hammering plate too cold will result in more brittleness of the 



iron which has to be reversed by tempering.  



The used iron should be soft and flexible [here he names sorts of iron 



that should not be used].  



Even though the shape of the starting-material is not important, for the 



aim of making plate, the use of flat iron is more sensible than the use of a 



bar of square section. The dimensions are chosen according to the 



aspired width and thickness of the plate.  



At the very first stage the iron bar is cut into its desired length, according 



to the desired length of the end-product. From such a piece in the end 



two plates will be revealed. This bar is called “Sturz”. It is of almost the 



double length of one later plate, because the work will concentrate 



mainly on extending the width of the bar . The lesser the iron will be 



stretched into length the more beautiful and better the plate will become.  



The cutting of the bars is achieved either by a hammer and a staked 



chisel or by machine-powered steel shears. For the first method the bars 



have to be heated white-hot, while for the latter method this is only 



necessary for thicker material. 



The iron bars are subsequently either heated in a smith’ s hearth or in an 



annealing furnace. White-heating the iron in a hearth is an impractical 



and coal-consuming method and the quality of the plates decreases. The 



bars are placed on iron sticks lying across the hearth. They are covered 



with coal from all sides and they are slowly heated with the help of the 



blower .  



When inserting the material into the furnace the heat should be 



increased rapidly to avoid the appearance of too much hammer-scale. 



The quantity of iron in the furnace at one time should not be higher than 



what can be handled within the time given. Keeping the material hot for



too long will result in a higher loss of the substance by combustion and 



an unnecessarily high use of coal.  



The method of producing plate under a hammer is old but still often 



used. Such a hammer usually weighs 200-250 kg. The lifting distance is 



usually 22 inches. The fin of the hammer measures 14 inches in length 



and ¾ inch in width. The surface of the anvil is shaped convex to allow a 



quicker spreading of the iron. The more slender the anvil is, the faster the 



work can be finished, but also more accuracy of the worker will be 



needed to get an even plate. Some hammers work with an anvil 4 inches 



wide; others use anvils of ¾ inch width. A more even and wider anvil will 



bring more plane sheet but the time required will be higher .  



[The author of this study has made a short movie that shows – in a simplified manner – the 



processes described in the following [ref_vid_pla].] 



The bars will be heated and then forged on one side to the double of their 



width. After heating them again also the other end will be treated the 



same way. Then the bar will we bend in its center and folded together by 



a hit of the hammer . Two workers are working together , one spreading 



the first, the other one the second end. The readily over-bent bars are 



now called “Urwellstürze” and this process-segment is called 



“urwellen”. One “Urwellsturz” consists of two halves, while each will 



later become one plate.  



The Urwellstürze will be heated again and forged at the side that is 



already spread to the double of the former width. After reheating, also 



the over-bent side will be spread. This work process is called “das 



Gleichen” or “das Stürzen” and the bars worked that way are called 



“Stürze” [again]. This work requires a lot of concentration as the 



material in the centre should not remain thicker than at the edges. The 



hammer has to hit the centre of the “Stürze” and drive the iron slowly to 



the side.  



In the next stage several pieces are worked under the hammer at once 



and thus more heat is required. To avoid a forge welding of the two 



plates, the “Stürze” are plunged into a liquid called “Hahnenbrei” 



[Engl. “rooster-pulp”], made of water , clay, chalk and coal dust. Then 



several “Stürze” are put together to one “Pack” or “Zange” of the 



weight of about 50 kg or – depending on the desired dimensions of each 



final plate – six to twenty pieces all together . The entity of “Zangen” that 



are worked together in one shift is called “Zeche”. Each “Zange” is 



heated and forged separately under the hammer . This is very hard work 



that requires a lot of experience. Thus always two workers are doing the 



job of constantly turning the pack, so the hammer does not hit the same 



spot for too many times. For the support of the worker and to keep the 



pack from falling off the anvil two right angled hooks are attached to 



each side of the anvil, the so called “Knecht” [Engl. “servant”], on 



which the pack can rest. To avoid that one side gets stretched more than 



the opposite side, the pack has to be turned – a job that also must not be 



neglected at the [aforesaid] processes of “Urwellen” and “Gleichen”. 



The worker has to take care, not to cause too many buckles or dints in



the surface of the plate. Because the plates are becoming cold very 



quickly, the pack has to be reheated and forged three to four times. After 



each round the packs have to be opened to see if the “Stürze” got welded 



together . If this is the case, they need to get separated. Then the “Stürze” 



are put back together in a new order . This is necessary as the plates in 



the centre of the pack keep the heat longer and thus they are extended 



more than those at the outer side.  



After the process has been repeated the third time, the plates should have 



reached the desired length. The pack is then opened and the single sheets 



are planed between a slow going “Pritsch- or Abrichthammer” and an 



anvil with a much larger surface. Afterwards the plates are finally planed 



with wooden hammers. The ready plates can be cut to their final 



dimensions – either by hand- or waterpowered scissors.
Karsten (1816), pp. 601 ff.; translation preserved from the dissertation.

Although later than medieval armour production, this account gives a detailed description of the older hammering method. Raw hammered sheets with untrimmed, burred edges reinforce the main wooden gates of Mauterndorf Castle in Austria [ref_ill_art_5389] PDF. Sheets delivered to medieval armourers probably looked similar. A Viennese document suggests that different objects required different blanks: in 1425 the locksmith Kristan von Melk owed the armourer Maister Lasslaben:

[…] 20 guldein oder 20 paingwandstürz [raw-plates for leg-armour] und 



20 hantschuchstürz [raw-plates for hand-protections] und 14 klain 



scheiben [small discs] […]
Jahrbuch (1895), Reg. 13651. 356
Redaktionelle Hinweise · 2
  • Die lange Karsten-Passage bleibt als überlieferte englische Übersetzung des Dissertationsautors unverändert. Begriffe wie „tempering“ für das Erweichen sowie historische Maßangaben sind bei einer gesonderten Neuübersetzung am deutschen Ausgangstext zu prüfen.
  • Die Videoeinfügung ref_vid_pla ist eine Erläuterung des Dissertationsautors innerhalb des übersetzten Auszugs.
Originalwortlaut vergleichen
7.2 The making of plates 



Armour plate cannot be cast. It needs to be forged or rolled from billets or bars, made by one 



of the techniques described above. In pre -industrial times , only wrought -iron had the 



required quality-characteristics – ductility and solidity in the correct ratio – to be used for 



the making of armour.  



There are only two ways to obtain a plate-sheet suitable for making armour. A billet or a bar 



has to get white -heated and then to get deformed by means of either a hammer or of rolls . 



The technique of rolling iron -plate was – according to the current stage of research – not 



successfully implemented before the end of the 17th century.346 Therefore, this technique was 



most likely not used for the making of late medieval armour -plate. The production of iron 



plate by a powered hammer has not been discussed scientifically so far. No details about the 



production of plate -sheet in the classical period of armour production were documented. 



Even though plate was produced and demanded ever since h umans found out about the use 



of metals for their own well, the written sources remain silent about the details of its 



production. Especially the production of plate from iron based material requires special skills 



and experience of the worker. Unlike the same work on copper based alloys 347, iron plate -



sheet can only be made from white-hot material – working it too cold would result in cracks 



in the material. Neither Agricola 348 nor Bringuccio349 or any other pre-industrial writer on 



metallurgy described the making of plate. The oldest descriptions of making hammered 



plated date from the late 18 th century; non e of them  has been edited and discussed in



connection to the making of armour. In the last 40 years few short articles were concerned 



with the topic of ancient plate-production350 and only one of them described the techniques 



of making plates with the hammer according to 18 th and 19th century sources351. Nearly all 



that the history of crafts, the art historys, the archaeology or archaeo -metallurgy published 



on the making of armour-plate is restrained to the level of guessing and thus it is not going 



to deep into the details of this particular technology. The assumption that the European black-



smiths before the 14 th century were not able to produce plate sheets large enough to make 



e.g. a breastplate, cannot be held. Already about the year 600 for the making of a bell in the 



German speaking lands steel (!) plate of 85 x 35 cm has been forged. 352 Such dimensions 



would easily serve for the making of a one -piece helme t or a breastplate. The basic 



technology for the making of large iron -plate was certainly known long before it was used 



for protecting other body parts than the head.  



It is possible to produce plate without any help from machines, but the mechanical 



deformation of a larger billet into the dimensions of a thin plate requires a lot of manpower 



and it is very time -consuming. It is possible that technological enhancements of 



waterpowered hammers played an important role in the emergence of more and more plate 



armour in the second half of the 14 th century. The use of waterpower was common in 



antiquity, but it had been declining through the early Middle Ages. Probably from the 11 th 



century paddle-wheels were increasingly used to operate different supplies like gr ain mills, 



grinding mills, bellows, hammers and later also mills for black powder. One of the earliest 



depictions of a waterpowered machine is a saw depicted in Villard de Honnecourt’s 13 th 



century sketchbook [ref_ill_art_5299].  



While not a single source mentions rolling -mills in the concerned period, the existence of 



hundreds of “Blechhämmer” (Ger.) (Engl. “plate hammer”) in the German speaking lands is 



documented. For example in 1409 a “ plechhammer” is mentioned in the possession of 



Conrad Eschenloer in Nuremberg 353 – by the end of the century a very important armour -



production city. The hammers were all located in close vicinity to natural water flows. This 



indicates that they were operate d by water -wheels. One of the oldest depictions of a 



waterpowered hammer dates from the last quarter of the 15 th century [ref_ill_art_5300]. 



Many illustrations in metallurgical books of th e 16 th and 17 th century also show such 



hammers [ref_ill_art_5297]. Different hammer-types existed for the production of various 



goods, but they cannot all be discussed this in the course o f the present study. Until today , 



in Europe some waterpowered hammers are still operating for educational purposes.  



One of the earliest detailed descriptions of the manufacture of plate metal is to be found in 



Carl J. B. Karsten’s book “Handbuch der Eisenhüttenkunde”, published 1816354. He gives a 



close instruction on  the production of plate by both, hammering and by rolling. In the 



following his descriptions on the hammer forging will be translated and transcribed.  



To bring the iron into the shape of plate – i. e. extending it both by its 



length and by its width at the same time – it has to be heated to white-



heat and then to be forged by the beats of a hammer . Only in rare cases 



the plate can be finished in one heat. Usually the iron […] would get 



cold before the plate would be finished. Thus – to get to the desired 



dimensions – it is necessary to reheat the iron several times. The amount 



of pieces handled in one work shift is defined by the capacity of the 



facility for the heating of the iron, the power of the hammer , the 



dimensions of the work piece and the experience of the producer . […] 



A good plate has to have the same thickness at each spot and it has to be 



free of buckles, wrinkles and delaminations355, as these are not simply 



disfigurements but they could also become problematic for the further 



working of the plate. Furthermore a good plate has to withstand a 



repeated bending and should not be so brittle to crack throughout this 



testing. Hammering plate too cold will result in more brittleness of the 



iron which has to be reversed by tempering.  



The used iron should be soft and flexible [here he names sorts of iron 



that should not be used].  



Even though the shape of the starting-material is not important, for the 



aim of making plate, the use of flat iron is more sensible than the use of a 



bar of square section. The dimensions are chosen according to the 



aspired width and thickness of the plate.  



At the very first stage the iron bar is cut into its desired length, according 



to the desired length of the end-product. From such a piece in the end 



two plates will be revealed. This bar is called “Sturz”. It is of almost the 



double length of one later plate, because the work will concentrate 



mainly on extending the width of the bar . The lesser the iron will be 



stretched into length the more beautiful and better the plate will become.  



The cutting of the bars is achieved either by a hammer and a staked 



chisel or by machine-powered steel shears. For the first method the bars 



have to be heated white-hot, while for the latter method this is only 



necessary for thicker material. 



The iron bars are subsequently either heated in a smith’ s hearth or in an 



annealing furnace. White-heating the iron in a hearth is an impractical 



and coal-consuming method and the quality of the plates decreases. The 



bars are placed on iron sticks lying across the hearth. They are covered 



with coal from all sides and they are slowly heated with the help of the 



blower .  



When inserting the material into the furnace the heat should be 



increased rapidly to avoid the appearance of too much hammer-scale. 



The quantity of iron in the furnace at one time should not be higher than 



what can be handled within the time given. Keeping the material hot for



too long will result in a higher loss of the substance by combustion and 



an unnecessarily high use of coal.  



The method of producing plate under a hammer is old but still often 



used. Such a hammer usually weighs 200-250 kg. The lifting distance is 



usually 22 inches. The fin of the hammer measures 14 inches in length 



and ¾ inch in width. The surface of the anvil is shaped convex to allow a 



quicker spreading of the iron. The more slender the anvil is, the faster the 



work can be finished, but also more accuracy of the worker will be 



needed to get an even plate. Some hammers work with an anvil 4 inches 



wide; others use anvils of ¾ inch width. A more even and wider anvil will 



bring more plane sheet but the time required will be higher .  



[The author of this study has made a short movie that shows – in a simplified manner – the 



processes described in the following [ref_vid_pla].] 



The bars will be heated and then forged on one side to the double of their 



width. After heating them again also the other end will be treated the 



same way. Then the bar will we bend in its center and folded together by 



a hit of the hammer . Two workers are working together , one spreading 



the first, the other one the second end. The readily over-bent bars are 



now called “Urwellstürze” and this process-segment is called 



“urwellen”. One “Urwellsturz” consists of two halves, while each will 



later become one plate.  



The Urwellstürze will be heated again and forged at the side that is 



already spread to the double of the former width. After reheating, also 



the over-bent side will be spread. This work process is called “das 



Gleichen” or “das Stürzen” and the bars worked that way are called 



“Stürze” [again]. This work requires a lot of concentration as the 



material in the centre should not remain thicker than at the edges. The 



hammer has to hit the centre of the “Stürze” and drive the iron slowly to 



the side.  



In the next stage several pieces are worked under the hammer at once 



and thus more heat is required. To avoid a forge welding of the two 



plates, the “Stürze” are plunged into a liquid called “Hahnenbrei” 



[Engl. “rooster-pulp”], made of water , clay, chalk and coal dust. Then 



several “Stürze” are put together to one “Pack” or “Zange” of the 



weight of about 50 kg or – depending on the desired dimensions of each 



final plate – six to twenty pieces all together . The entity of “Zangen” that 



are worked together in one shift is called “Zeche”. Each “Zange” is 



heated and forged separately under the hammer . This is very hard work 



that requires a lot of experience. Thus always two workers are doing the 



job of constantly turning the pack, so the hammer does not hit the same 



spot for too many times. For the support of the worker and to keep the 



pack from falling off the anvil two right angled hooks are attached to 



each side of the anvil, the so called “Knecht” [Engl. “servant”], on 



which the pack can rest. To avoid that one side gets stretched more than 



the opposite side, the pack has to be turned – a job that also must not be 



neglected at the [aforesaid] processes of “Urwellen” and “Gleichen”. 



The worker has to take care, not to cause too many buckles or dints in



the surface of the plate. Because the plates are becoming cold very 



quickly, the pack has to be reheated and forged three to four times. After 



each round the packs have to be opened to see if the “Stürze” got welded 



together . If this is the case, they need to get separated. Then the “Stürze” 



are put back together in a new order . This is necessary as the plates in 



the centre of the pack keep the heat longer and thus they are extended 



more than those at the outer side.  



After the process has been repeated the third time, the plates should have 



reached the desired length. The pack is then opened and the single sheets 



are planed between a slow going “Pritsch- or Abrichthammer” and an 



anvil with a much larger surface. Afterwards the plates are finally planed 



with wooden hammers. The ready plates can be cut to their final 



dimensions – either by hand- or waterpowered scissors.  



Even though this description is not  contemporary with the ancient armour making, it 



provides a detailed insight on how plate was actually made in pre -industrial times. Several 



clearly hammered raw plate -sheets – the edges left burred – are nailed as reinforcement to 



exterior side of the woo den main -gates at the Castle in Mauterndorf/Austria 



[ref_ill_art_5389]. The plates delivered to a late medieval armourer’s workshop must have 



looked very similar to these. A Viennese docum ent from the beginning of the 15 th century 



suggests that the armourers chose different plate -dimensions for different armour types. In 



1425 the lock-smith Kristan von Melk owes to the armourer Maister Lasslaben:  



[…] 20 guldein oder 20 paingwandstürz [raw-plates for leg-armour] und 



20 hantschuchstürz [raw-plates for hand-protections] und 14 klain 



scheiben [small discs] […]356
S. 189–192 · Sprachlich überarbeitet · Entwurf

7.3 Plate quality

Armour had to resist different weapons. Late medieval armourers could obtain sheet of different qualities and prices, choosing unhardened iron or stronger steel, potentially improved by heat treatment, according to the commission. Relatively soft iron requires greater thickness to offer protection comparable to thinner steel, increasing weight. Steel therefore offered a way to combine lower weight with greater resistance. In the late thirteenth century, Jansen Enikel already described the biblical Goliath’s helmet as follows:

[…] 



dar zuo hat er ein isenhuot,  



der ist von stahel also guot, 



daz uf ertrich dhein man 



so vestes huotes ni gewan 



[…]
Jansen Enikel, cited in Strauch (1986), p. 185. 357

This does not establish heat treatment. Unhardened steel can itself resist penetration better than iron. Nevertheless, since hardening was known in antiquity, armourers who deliberately selected and advertised steel probably often exploited that property. Customers paying more would expect better protection.

Historic documents distinguish material qualities.358 An inventory of 1464 lists:

[…] 4 wälschi359 ställichi [steel] panzer , 4 eisneni [iron] banzer , […]
Inventory of 1464; Jahrbuch (1899), Reg. 17851. 360

The wording shows contemporary awareness of a distinction between iron and steel, although “panzer” in this document may refer to ring armour rather than plate armour.

Documents also identify supply regions. Nuremberg used iron from the Upper Palatinate and steel exclusively from Styria.361 In the early sixteenth century, Maximilian required his Innsbruck armoury to obtain both iron and steel from Styria. From 1501, he ordered Leoben material to bear the city’s ostrich mark as a quality guarantee, continuing a practice occasionally used earlier.362

Nearly all plate armour is made from iron-based sheet,363 also used for doors, chests and other purposes.364 Metallurgical examination is needed to distinguish iron from steel reliably.365 In the following discussion, “iron” therefore sometimes serves as a collective term for iron-based material. Applying the modern industrial term “steel” indiscriminately would obscure the distinction between hardenable steel and comparatively soft, low-carbon historic material.

Several metallurgical studies, especially Alan Williams’s work,366 demonstrate the use of steel in different regions and grades of armour. Even some of the earliest medieval plates were hardened. Quality was undoubtedly influenced by cost, but it affected the basic forming operations only modestly. Unhardened steel may require more force during cold working than softer iron, yet the general methods remain similar. Material quality alone cannot establish authenticity, since processes resembling medieval ironmaking continued into the early twentieth century.

The main additional work came after shaping. Soft iron needed grinding, polishing and assembly; steel intended for hardening required heat treatment. Grinding beforehand reduced the time and abrasive needed. Temporary supports may have helped prevent distortion during heating and quenching.

The plate was heated throughout into the austenitic range—the source gives a simplified threshold above 723 °C—then cooled more rapidly than by leaving it in still air. Rapid immersion in a cold liquid could produce very hard but brittle material. Controlled cooling in warmer media, including heated liquids, molten lead or heated sand, could yield a different balance of hardness and flexibility. The precise result depends on composition and the cooling cycle. Reheating quenched steel at a lower temperature reduces brittleness: tempering temperatures may range from about 150 to 600 °C according to the required properties and alloy composition.367

Heat-treating large plates was difficult. Their shape had to be completed first, since hardened material could not readily be corrected. Heating released stresses introduced during cold shaping, while the object’s own weight or pressure from handling tongs could distort it. Correction would require reheating, slow cooling to soften the metal, reshaping and repeating the treatment.

A temporary internal framework might have prevented such distortion. Holes intended for later fittings could secure it with screws, wire or rivets. In any case, drilling or punching the holes before hardening was easier.

Redaktionelle Hinweise · 2
  • 723 °C ist im Original eine vereinfachte Austenitisierungsangabe. Die konkrete Temperatur und Wirkung der genannten Kühlmedien sind legierungs- und verfahrensabhängig; fachliche Prüfung erforderlich.
  • Das Original setzt historische Eisensorten, modernes „steel“ und Härtbarkeit teilweise pauschal gleich. Die terminologischen Grenzen werden benannt, ohne Analysedaten hinzuzufügen.
Originalwortlaut vergleichen
7.3 Plate quality 



Armour needs to resist attacks by different types of weapons. The late medieval armourers 



had plate of different quality – and price – available that could fulfill this demand to a certain 



degree. Depending on the client’s  requirement, armour could be made from cheaper, not 



hardened iron-plate or from a tougher and maybe even heat -treated steel-plate. Pure iron is 



rather weak and thus it needs to be used in larger thicknesses to get protective properties 



similar to thinner steel plate. This comes together with an increas e in  weight. If armour 



should be both light and strong, there is the possibility to use steel instead of iron. Already 



in the late 13th century Jansen Enikel in his description of the biblical Goliath’s appea rance 



wrote:



[…] 



dar zuo hat er ein isenhuot,  



der ist von stahel also guot, 



daz uf ertrich dhein man 



so vestes huotes ni gewan 



[…]357 



This source does not say that the helmet was actually also heat -treated. It might have been 



made of un -hardened steel, whi ch could indeed already show better penetration -resistance 



than iron plate. As the technique of hardening steel was known since antiquity, it is very 



unlikely that the armourers did not harden their products after they had already purposely 



and proudly made them from steel. Furthermore, the buyer would only be willing to pay the 



higher price for steel armour if he would get a product with protective properties superior to 



lower-cost iron-plate armour.  



The historical sources do clearly differentiate between  the two qualities.358 For example an 



inventory of 1464 for lists  



[…] 4 wälschi359 ställichi [steel] panzer , 4 eisneni [iron] banzer , […]360  



These notes show that the contemporaries were well aware of the material -qualities of 



different armour parts.  



From contemporary documents some of the main supplying regions for certain armour -



production cities can be identified. Nuremberg used iron from the Oberpfalz, the steel came 



exclusively from the Steyermark.361 King Maximilian I. for his court-armoury in Innsbruck 



in the early 16 th century ordered that iron and steel must only be supplied form the 



Steyermark. As a quality prove, the iron and steel from Leoben on order of Maximilian I. 



from 1501 on had to be marked with the cities coat of arms – an ostrich – as it w as also 



(occasionally) done before.362



Nearly363 all plate armour is made from plate -sheets of an iron -alloy. In the Middle Ages 



plate was not only used for making armour, but also for the reinforcement of doors or 



chests364 etc. As only metallurgical examination365 can show the quality of any material – i. 



e. if a certain item was made of steel or iron – in the following considerations the two terms 



will be summarized as “iron”. Modern metallurgical terminology summarizes all industrial 



produced iron based material as “steel”. It would be confusing to generally adopt this term 



to all historical iron-alloys as some objects were evidently made of rather soft iron that could 



not be hardened like steel. That steel occasionally has been used in the different armour 



production regions and for different armour qualities has been proofed in several 



metallurgical studies; most of them were carried out by Alan Williams366. Even some of the 



oldest medieval plate-armour items were found to be made of hardened steel. The material 



quality was certainly a matter of cost. The basic processes the armourer had to apply for the 



production of a certain armour part depended only insignificantly on the quality of the 



material used. Furthermore, the material quality does not answer the auth enticity question, 



as steel and iron until the early 20th century was produced in methods similar to late medieval 



processes. The making of armour from steel-plate is probably not different from its making 



in iron. The armourer might have needed more force  when he cold-hammered steel, as this 



material is usually tougher than iron, even when not hardened. The only relevant difference 



emerged when the shaping of the plates was finished. While armour made of softer iron 



simply needed to be ground, polished and  mounted, the steel -armour needed some more 



laborious treatment. It was certainly best to grind it before it was hardened, as doing this 



work afterwards would be much more abrasive - and time -consuming. To avoid a 



deformation of the ready -shaped plates caus ed by the heat -treatment process it might be 



necessary to apply a temporary supportive construction. The item then needed to be heated 



all over to a red -hot temperature (above 723 0C – austenitizing temperature) and then to be 



cooled quicker than it would do when just left exposed to room temperature. Basically two 



ways of cooling can be applied: either by a rapid “plunging” of the item into a cold liquid, 



or by cooling it more slowly – e. g. in a warmed liquid, melted lead or heated sand. In the 



latter case the purpose is to achieve a delay in the cooling in comparison to a more rapid 



cooling to room-temperature. The steel treated in such a way is hard but very flexible as 



well. Steel that had been plunged red -hot into cold water becomes very brittle and ha rd. To 



avoid the steel product from breaking, the brittleness can be reduced by heating the steel 



again for a longer time at a constant temperature – depending on the desired mechanical



properties and the chemical composition of the material – ranging between 150 and 600 0C 



(tempering).367  



The tempering of plate armour was a difficult task. The larger the plate was, the more care 



the armourer had to take when he heat treated one of his products. The most important was, 



to avoid a deformation of the overall red hot object. The shape had to be finished before the 



heat treatment and no subsequent correction was possible. Stresses inside the material, 



deriving from the cold shaping process, got released when the item was heated. This, 



together with the force of the own weight could easily have led to a deformation of the work 



piece. But also a tong used for handling the hot object when plunging it into e.g. water might 



have resulted in a distortion. Correcting a distortion after hardening meant to first heat the 



steel for a longer time red hot and then to let it cool very slowly to soften it again. Then the 



form could be altered again and the heat treatment could subsequently be repeated. The best 



way to a void the necessity of such time -consuming correction would h ave been the 



installation of a stabilizing framework inside the object – before it was hardened. The holes 



for the later attachment of different applications could have served to fix such a construction. 



It was anyway easier to drill or punch holes before the object was hardened. The supportive 



framework might have been attached by screws, by wire or by rivets.
S. 192–193 · Sprachlich überarbeitet · Entwurf

7.3.1 Converting iron to steel: carburising and case hardening

Carburising introduces carbon into the surface of low-carbon iron, making that region hardenable. It depends on atomic diffusion and on a suitable carbon-bearing atmosphere, notably the balance between carbon monoxide (CO) and carbon dioxide (CO₂). Under appropriate conditions, two CO molecules can supply carbon to the iron while forming CO₂.

Burning charcoal can provide such an atmosphere if the air supply is controlled. A coating of clay and charcoal dust can maintain carbon-rich conditions around the workpiece during heating. The twelfth-century Benedictine monk Theophilus describes the basic process.368 It was particularly useful for tools and blades requiring a hard surface or edge over a tougher core.

The “liber illuministarum” mentions rubbing iron with organic substances and then heating it, but omits a clay enclosure and the necessary reaction time.369 Effective carburising requires prolonged heating—several hours in the conditions described here—at roughly 870–950 °C. Maintaining a high temperature while preserving a suitable carbon potential is difficult. An atmosphere favouring CO₂ can instead decarburise or oxidise the metal. An enclosed chamber separating the workpiece from the combustion airflow offers better control than an open forge.

Longer exposure allows carbon to penetrate further. Verhoeven gives the following relationship for estimating diffusion time:370

t = d² / (6D), where t is time in seconds, d the carburised depth and D the diffusion coefficient (Verhoeven, table 7.4).371

After carburising, the carbon-enriched region can be hardened by heat treatment as described above.

Nitriding is another surface-hardening method. The source contrasts a modern treatment at about 600 °C with medieval recipes for quenching hot iron in substances containing earthworms, hair, horn, claws or excrement. Their brief exposure and imprecise descriptions do not establish use of a controlled nitriding process in the late Middle Ages. The source suggests that some combination of surface carburising and nitrogen uptake might have occurred, but this remains uncertain.372

Only a few armour objects have been proposed as deliberately surface-hardened by such methods. Williams identified particular examples as case-carburised and quenched.373

Redaktionelle Hinweise · 3
  • Die mathematische Schreibweise „dxd/6xD“ ist als d²/(6D) gesetzt; Einheiten von d und D müssen zusammenpassen.
  • Das Original vermischt Nitrat, Stickstoffaufnahme und Nitrieren. Die historische Anwendung wird deshalb ausdrücklich als ungesichert beschrieben; Badzusammensetzung und Reaktionsannahmen sind fachlich zu prüfen.
  • Die Aussage, stärkeres Einblasen führe automatisch zu mehr CO₂, wurde nicht als allgemeingültige chemische Regel übernommen.
Originalwortlaut vergleichen
7.3.1 Turning iron into steel: Case carburizing – case hardening 



The so called case carburizing method can be employed if low-carbon iron should be turned 



into steel. This is the attempt to bring carbon into the surface of the material from outside. 



Case carburizing is actually based on the mechanism of atom migration – diffusion – within 



a metal. The main requirement for the migration of carbon into iron i s the availability of a 



gas being a mix of carbon monoxide (CO) and carbon dioxide (CO2). If the relative amount 



of CO is higher than that of CO2 one carbon atom will dissolve from two CO molecules into 



the iron, leaving a CO 2 molecule that will float off. When charcoal, the common fuel for a 



smith’s hearth in the Middle Ages, is burned, such a gas will form if not too much air is 



blown into the fire. To bring and keep carbon close to the iron which should be carburized it 



can be coated for example with a mixture of clay and charcoal dust and subsequently be 



heated in the charcoal fire. The basic process is already described by the 12 th century 



Benedictine munch Theophilus. 368 It was especially adopted for the production of tools or 



blades which needed to have a flexible core but also a high hardness at edges and surfaces. 



The “liber illuministarum” mentions the rubbing of the iron with organic material and its 



following heating in the fire. The text does not mention the necessary coating of clay and the 



necessary reaction time.369 To make the carbon diffusing from the coating into the iron, the 



work-piece inside such a carbon -rich packing needed to be kept for several hours at a 



temperature of about 870 to 950 0C. The difficulty is, to heat the item hot enough for allowing 



a rather quick diffusion of carbon into the iron while keeping at the same time the CO ratio 



high in the gas in contact with the iron. If the ratio of CO 2 is higher, the iron might become 



decarburized or even oxidized. But reaching higher temperatures in a simple smith’s hearth 



with an airflow controlled by bellows means automatically to blow more CO 2 into the open 



fire. Only a closed oven chamber, where the air float for the fire is kept outside can provide 



a stability of the required conditions. The longer an item is kept under these premises the 



more carbon will diffuse into the iron. It is difficult to estimate the temperature at which the



diffusion begins and how deep the carbon will migrate in which time. V erhoeven gives the 



following equation for the calculation of the diffusion-depth370:  



Time (s) = dxd/6xD  



(d= depth of carburization; D= diffusion coefficient, given in V erhoeven tablet 7.4) 371 



After the carburization, i.e. turning part of the iron into steel, it can be hardened like any 



other steel (see description above). 



Another method for hardening the surface of steel is nitration. Here the steel has to be kept 



for a certain time in a 600 C hot nitrate bath. The “liber illuministarum” only describes the 



process of quenching the hot iron into nitrate rich substances such as earthworms, or liquids 



containing hair, horn, claws, or excrement. As, according to the described recipe, the material 



was kept for only a short time in these substances, nitrate could not move into the surface of 



the iron. The technique is not described precisely enough to assume the employment of the 



modern nitrating method for the late Middle Ages. What could have happened to a steel 



plunged into the said substances was probably a mix of su rface carburizing and nitrating of 



the steel.372  



Only few armour pieces were suggested to have been hardened only on the surface region 



by one of the methods described. It was Alan Williams who suggested that some specific 



parts had got purposely case carburized and quenched.373
S. 193 · Sprachlich überarbeitet · Entwurf

7.4 Metallurgical examination

Alongside visual examination and documentary research, metallurgical methods can provide further evidence about iron objects.374 Four principal questions concern the material’s origin, date, manufacturing process and quality.

Originalwortlaut vergleichen
7.4 Metallurgical testing 



Aside from the examination of features visible with the naked eye or retraceable by 



documentary research also metallurgical testing-methods have the potential to reveal further 



data on iron artifacts. The four main questions that could potentially be answe red by such 



methods are on the place, the date, the production technique and the quality of the material.
S. 193–196 · Sprachlich überarbeitet · Entwurf

7.4.1 Methods for assessing material quality

Two principal characteristics are commonly examined: hardness and microstructure. For thin armour plate, suitable hardness tests press an indenter into the surface under a known load. The impression’s dimensions yield a numerical hardness value.375 The mark can be as small as a grain of sand, and no sample need be detached. These values compare resistance to local indentation. High hardness may indicate steel and deliberate heat treatment, but cannot itself establish provenance or date: comparable properties occur in both old and modern metal.

Metallography examines microstructure to investigate material quality and possible heat treatment. A small area must be polished to remove corrosion and reveal the metal. Preparing an accessible plate edge often avoids detaching a sample and is generally preferred to polishing an exterior surface. Etching then reveals structural differences under a reflected-light microscope.

The resulting pattern of grains and phases can be assessed by shape, size and appearance. A specialist can estimate carbon content at the examined location and recognise inclusions as dark elongated features or spots. Microstructure may also show heat treatment and suggest the method used. Slag inclusions or mechanically produced layering can indicate a wrought-iron process. Conversely, few inclusions and no visible layering may suggest modern liquid-state steel, although the following discussion considers the limits of that inference.

Chemical analysis may help constrain date. According to Craddock, significant manganese is likely to indicate manufacture no earlier than the nineteenth century, whereas its absence permits any date. Deliberate alloys with other metals, apart from nickel, are likewise considered unlikely before the mid-nineteenth century. Absence of sulphur is not a reliable sign of pre-eighteenth-century manufacture: higher furnace temperatures reduced sulphur from the mid-eighteenth century onwards, so later reproductions can also contain little or none.376

Optical emission spectrometry analyses light generated by an electric arc between the sample and an electrode, here described as copper or silver.377 Elements emit characteristic wavelengths; their intensities indicate concentration. The method described leaves a burnt area about 1 cm across.

X-ray fluorescence offers non-destructive elemental analysis. Incident X-rays excite characteristic emissions that a detector records, allowing elemental identification and estimation of relative amounts. The equipment discussed here cannot detect carbon, a crucial limitation for iron and steel; the source gives an atomic-number threshold above eight and a typical sampling depth of about 0.1 mm. Because historic material can be heterogeneous, a surface measurement may not represent the interior.

Could chemical composition also reveal origin? That would require extensive comparative analyses of ores from many mining sites. Matching an object to a mine might constrain its material’s history; a documented closure could potentially supply a terminus ante quem for extraction. It would not, by itself, date the later manufacture of the object.

Several obstacles remain. Iron ores, charcoal and furnace-building materials were widely available, and iron was produced throughout Europe for millennia. Mixing scrap from different sources could alter composition. Different refining methods could also produce different materials from the same ore. In this period, quality probably depended more on refining than on the natural resource, and the armourer might work far from both mine and smelter.

No sufficiently established ore fingerprinting framework was available to this study. Slag analysis may help: several projects have attempted to characterise and provenance historic iron through its inclusions.378 Their results had not yet been brought together in a central dataset capable of resolving armour authenticity.

Scanning electron microscopy (SEM) provides another means of surface investigation. An electron beam generates signals that reveal topography and, with appropriate detection, chemical composition and other properties. The method examines only the sampled surface. Conventional vacuum chambers may be too small for large armour objects. I knew of no SEM study of armour at the time of writing. A substantial comparative programme might help characterise source materials and refining techniques.

Radiocarbon analysis measures carbon isotopes in iron, but this study considers its usefulness for armour limited. Sampling is destructive: the amount removed must yield about 1 mg of carbon, potentially requiring a substantial fragment from low-carbon metal.379 Later oils or coatings in pores and cracks can contaminate the carbon signal. Mixed scrap and carbon-bearing fluxes can also complicate results. Cook and colleagues reported that European armour in their study could not be dated successfully, probably for such reasons.380

Unpublished attempts have also dated attached leather or material trapped between plates. Such measurements date the sampled substance, not automatically the armour. Old organic material can be introduced later, accidentally or deliberately, so its relationship to the plate must be established independently.381

Redaktionelle Hinweise · 3
  • Geräteleistung, Nachweisgrenzen, Probengrößen und Stand der Forschung sind Angaben der Dissertation und keine aktuelle Übersicht.
  • Die Vorlage beschreibt Mikrostrukturbilder teils als direkte Landkarten chemischer Elemente. Präzisiert zu Gefügephasen und Einschlüssen; keine zusätzlichen Messresultate.
  • Die Herkunfts- und Datierungsgrenzen der Metall- und Organikproben bleiben ausdrücklich getrennt.
Originalwortlaut vergleichen
7.4.1 Quality testing methods 



Modern metallurgy 374 usually tests two quality -characteristics of a sample -material: the 



hardness and the crystalline-microstructure.  



The hardness can be tested by different methods. For the relatively thin armour plates only 



such testing methods are useable that press a body of certain hardness with a known force 



into the sample’s surface. The indented body leaves a mark at the artifact, its dimensions  



allow the calculation of a characteristic figure 375 expressing the material’s hardness. The 



damage the indentation leaves can be limited to the size of a grain of sand and no part of the 



sample needs to be detached. The revealed data  expresses in comparable numbers the 



durability of the material against any kind of penetration. Whenever an armour part is found 



to be hard, it is likely that the armourer used steel instead of iron and he probably purposely 



heat treated his product . The hardness-testing method cannot tell anything about the



provenance or date of an item, as the same factors can be found equally at modern or ancient 



material as well. 



Further information on the quality of the sample -material and the possible methods used to 



improve its hardness can be gained by the examination of the crystalline -microstructure. 



This structure is made visible by a microscopic image. The specialized method for this 



imaging method is called “metallography”. As the surface of iron artifacts is usually coated 



by corrosion-products, a small section of the sample needs to be polished. If this is done at 



the cut-edge of a plate, the sample does usually not have to be detached from the artifact. 



This sampling method is usually preferred over the grind ing and polishing of the outer 



surface of an artifact. After the polishing, the different chemical components need to be 



virtually emphasized with the help of acid. Under a reflected -light microscope now the 



crystalline-microstructure becomes visible. The image shows a map -like arrangement of 



fields that can be classified by shape, size and color. The different elements present describe 



their own characteristic field and color. A specialist now can estimate for example the amount 



of carbon present at the ex amined location. If non-metallic inclusions like charcoal or slag 



are present, they can be seen as elongated dark lines or as dots. By the arrangement of the 



crystals (phases) the metallurgist further can tell if the hardness of the material was increased 



by heat treatment and he can make suggestions on the method used to achieve such 



properties. This method cannot tell about the provenance of the artifact, but it can suggest – 



if slag inclusions are present or if layers deriving from mechanical refining pr ocesses are 



visible – that the material was made by a wrought -iron production-technique. If no or only 



small inclusions and no layered structure are visible, the material might be modern mild -



steel. 



An analysis of the chemical components might help to narrow down the date an iron or steel 



artifact has been produced. If for example manganese is present in significant amounts, 



according to Craddock it is very likely that the material was made not before the early 19 th 



century. On the other hand, iron with no amounts of manganese can be of any date. Also 



alloys of iron and other metals – with the exception of nickel – are very unlikely to pre-date 



the mid-19th century. Craddock says that the approach of defining all material containing no 



sulphur to be rather older than the 18 th century – the time when melting furnaces started to 



be operated with coal as fuel – is not suitable for the detection of forgeries. Already from the 



mid-18th century on the sulphur content decreased, as higher furnace operating temperatures 



allowed for a reduction of this element off the melt. Therefore, also 19 th or 20th century 



reproductions might contain no or only little sulphur.376  



Different element -quantity testing methods exist. The optical -emission-spectrometry 



analyzes the light emitted from an electric-arc activated between the sample and a copper or 



silver electrode. 377 Each element present in the sample emits light of a character istic 



wavelength. The intensity of the radiation tells about the present quantity. This testing 



method leaves a burned spot of about 1 cm in diameter on the surface of the artifact.  



A non-destructive possibility for the determination of the chemical components of a sample 



is provided by different X-ray analysis systems. The X-ray fluorescence sends X-ray beams 



into the sample, these beams are absorbed by the material, re -emitted and recognized by a 



detector. Each present element shows a specific emission -spectrum. By this method the 



presence and the ratios of the contained elements can be verified. The problem of the



examination of iron with these systems is that a very important element – carbon – cannot 



be detected; only elements with an atomic number hig her than 8 can be identified. Another 



problem is that only to a depth of ca. 0.1 mm the present elements can be detected. As the 



pre-industrial iron material is expected to be rather heterogeneous in its chemical 



components, the XRF-results do not tell anything about the situation deeper in the volume.  



An analysis of the quantity of elements present in a sample -material tells about its quality 



and the production process. It is also a logical consequence to ask if the results can maybe 



tell where the material came from. To answer this question it would be necessary to test the 



chemical characteristics of iron-ores sampled from a large number of different mining-sites. 



The characteristics could be compared to the chemical composition of iron -artifacts, with 



the possible result that the source of the material could be identified. If the mining -site was 



evidently closed at a certain time, even a “terminus ante quem” for the production of the 



iron-sample could be presumed. Nevertheless, it would still be problema tic to clearly 



identify a mining site. Unlike most other metals or alloys, iron could be produced almost 



everywhere in the world. Iron ore can often easily be mined. The fuel necessary for the 



operation of a melting furnace is charcoal, which can be made f rom any kind of wood. The 



only material needed for the building of a furnace is clay and stone. Thus, throughout all the 



last 3000 years iron has been produced all over Europe. Furthermore, the possible addition 



of scrap-metal – produced from different ore – in the refining process could have influenced 



the chemical composition. It is also possible that from one sort of ore different alloys and 



iron-qualities were produced – with a result of different chemical characteristics. In the 



considered period the q uality of the iron did probably depend much more on the refining 



technique than on the available natural resources. Furthermore, the location of an armourer’s 



workshop could still have been far away from the ore mining-site and the smelting furnace. 



Until today no chemical fingerprint of certain iron ore mines could be discovered. Maybe 



future research can help to map iron artifacts to the sources of the ore. The analysis of iron 



slag might help to approach this topic. Some slag -analysis projects with the aim of 



provenancing and characterizing ancient iron artifacts have been carried out in the past. 378 



The results do not yet help to attest the authenticity of iron artifacts, as no project centralizing 



the data exists yet. 



Another nondestructive testing metho d is provided by a scanning -electron-microscope 



(SEM). A beam of electrons makes the atoms on the sample’s surface sending back signals 



that provide information on the scanned object’s topography, chemical composition, and 



other properties such as electric al conductivity. This me thod delivers information on the 



surface’s sample only. The artifact has to be examined in a vacuum and therefore for 



examining armour the testing chamber has to be rather large. The author does not know about 



any SEM -testing of arm our. The results of such examinations could help to identify the 



sources of the material and the refining technique if a large scale study producing immense 



quantities of comparable data would be carried out. 



A natural-scientific method used for the dating  of iron -based artifacts is the quantitative 



analysis of C14 isotopes present in the sample material. This age-testing method – called the 



“radiocarbon dating” method – is not reasonable for iron artifacts. First of all, it inevitably 



damages the tested ob ject. In any case a flake of considerable size 379 – depending on the 



amount of carbon in the material – has to be detached to reveal at least about 1 mg of carbon. 



The results are often unclear, due to impurities containing C14 isotopes – e. g. oils or coatings



– that got secondarily added into pores or cracks in the sample. Also admixed scrap-metal or 



welding fluxes like limestone would lead to falsified results. According to Cook et. al. 



probably due to this reason the European armour examined in a vast study on the age of iron 



objects could not be dated by the radiocarbon -method.380 Unpublished attempts have been 



made to date armour by C14-testing of attached organic parts like leather or simply dirt from 



in between the plates. The results tell about the age of these substances only, not about the 



plates themselves. To make an item authentic, for example old wood – e. g. easy to be 



obtained from a torn -down house – could serve for mixing an ancient C14 -cocktail. If a 



criminal mind intended to fake an artifact, such a cocktail could be daubed on armour-leather 



or into narrow gaps between the plates from where later a sample would be taken.381
S. 196–197 · Sprachlich überarbeitet · Entwurf

7.4.2 X-ray imaging

X-ray imaging has sometimes provided strong evidence for assessing authenticity, particularly in objects combining different metals, such as swords and hafted weapons. Historic makers forge-welded different materials to obtain mechanical properties or decoration. Reproducing these structures can be difficult, and two- or three-dimensional imaging can reveal their arrangement without damaging the object.382

Armour presents a harder problem because its sheet usually lacks such conspicuous composite structures. Conventional radiography offers limited information, though it can expose modern welds or concealed repairs. Micro-computed tomography (micro-CT) reconstructs the internal volume in three dimensions.383 Rotation of the sample or X-ray source provides views from multiple directions, allowing virtual exploration of inclusions, cavities and other structures without sectioning the object.

X-rays are attenuated differently as they pass through different regions of the material. A detector records the transmitted intensities, and computation reconstructs their spatial distribution. Advances in computing greatly improved metal micro-CT during the two decades preceding this study. Industrial systems could achieve resolutions around 5 µm.

In conventional geometry, the beam crosses the rotation axis at 90°. This suits roughly cylindrical samples, whose thickness and attenuation remain broadly similar as they rotate. The scans discussed here cannot reliably resolve every small local variation. Chamber and sample-size restrictions probably explain why large armour objects had not yet been investigated in this way. Internal images might nevertheless identify manufacturing structures and constrain the possible period of production without sampling damage. The later section on new approaches introduces another promising X-ray method not previously applied to this question.

Redaktionelle Hinweise · 1
  • Auflösungsangaben und die behauptete bisher fehlende Untersuchung von Plattenpanzerung sind zeitgebunden. Keine Aussage über den heutigen Stand der Tomographie.
Originalwortlaut vergleichen
7.4.2 X-ray based imaging methods 



In a few cases X -ray imaging methods delivered reliable information for the determination 



of an artifact as genuine or reproduced. This is especially the case for artifacts of complex 



material systems, like swords or hafted weapons. At genuine examples often different alloys 



had been fire-welded to reveal certain mechanical properties or decorative elements. These 



features of genuine items are difficult to be reproduced by a forger. The authenticity testing 



of swords with the help of non -destructive, 2- or 3D-imaging X-ray methods is therefore 



often successful, as the different components of genuine items can clearly be visualized.382  



It is more difficult to examine armour by X -ray methods. The material does usually not 



consist of different alloys welded together. Simple 2D X-ray imaging (radiography) does not 



tell a lot about an item. It can only be helpful to detect modern welding seams or camouflaged 



repairing. Micro c omputed-tomography383 offers the possibility to non -destructively 



reconstruct 3D views of the interior structure of a sample material. T he main difference to 



common X-ray examination (radiography) is that a rotation of either the sample or the X -



ray source during the scan delivers information from all three dimensions. To say it in easy 



words: The spectator of a reconstructed scan can virt ually “fly” through the scanned 



substance. What such images are sought to show, are structures within the sample’s volume 



(inclusions, cavities etc.). The main difference to other testing methods like microscope -



examination is that the sample does not have  to be dissected, i. e. damaged. Basically the 



method works as follows: X-ray beams are sent through the substance. Differences in the 



density of the examined substance passed by these beams do locally differently absorb the 



X-rays. The detector of the sca nning device recognizes the smallest intensity -deviations. A 



computer correlates these deviations and processes an image.  



Due to the permanent increase of computer -processing-capabilities throughout the last 



twenty years, the testing of  metals with the he lp of micro c omputed-tomography had been 



immensely processed. The resolution of the scans revealed from industrially used CT’s 



already reaches down to ~5 µm. In the conventional method the X -rays cross the sample’s 



rotating axis in a 90 0 degree angle. This  technique is ideal for scanning more or less 



cylindrical samples, where the thickness and therefore the absorption is more or less equal 



in all scanning -directions. The results of such scans cannot detect very small  and local



density-variations. Probably due to the sample size -limitations of most of the micro 



computer-tomographs, none of the usually large armour parts has yet been tested by this 



method. The images could help to tell by which method the material was made. Such 



information could possibly be used to narrow down the time-frame in which a tested artifact 



had presumably been made.  The biggest advantage is, that a tested artifact would not get 



damaged. In chapter [Ideas for new approaches] the author describes another promising X-



ray based imaging method that had previously not been used to approach the question on 



authenticity.
S. 197–199 · Sprachlich überarbeitet · Entwurf

7.4.3 Assessing armour authenticity

Inclusions have often been treated as the strongest metallurgical distinction between originals and reproductions. If metallography revealed none, the material was classified as modern steel and the object as a reproduction. This reasoning overlooks both the continued use of older ironmaking methods during the period of reproduction and the possibility that historic makers could produce exceptionally clean material, at least locally.

An authenticity investigation should first establish, as far as possible, how the metal was produced. At the time of this study, insufficient comparative research existed to distinguish the various mechanically refined materials reliably. Basic questions remained unresolved. Must wrought-iron sheet contain visible inclusions? Could an armour blank have been made from a large, relatively clean bloom without repeated forge-welding?

Charles’s work suggests the latter possibility.384 He notes that bloomery iron can be very clean because solid-state reduction at lower temperatures need not reduce silicon from silicates into the metal.385 A Norwegian bloom found near Trondheim and radiocarbon-dated to AD 390–545 offers further evidence. Its outer region contained almost no carbon, while its interior was comparatively homogeneous at about 0.7% carbon. It had a few large cavities but almost no slag inclusions.386

Repeated folding, welding and prolonged high-temperature exposure might also reduce visible banding until metallography no longer detects it. Genuine armour could therefore contain few recognisable defects. Conversely, inclusions do not necessarily establish antiquity. Puddled iron remained in production into the twentieth century: Donawitz’s last puddling furnace closed in 1917.387

During the height of armour reproduction, puddling remained a major source of iron. In 1878, 1,533 furnaces produced 24,723,029 cwt of wrought iron,388 more than twice the corresponding steel output.389 In Germany that year, 178 charcoal-fired fineries also produced 446,670 cwt from scrap.390 The assumption that nineteenth-century material invariably came from coal-fired furnaces, and therefore contained diagnostic sulphur, is untenable.

Nor must reproduction armour have been made from rolled sheet. Late nineteenth-century sources describe thick ship armour hammered mechanically in England, preferably from recycled wrought-iron scrap. Hammered plate was considered superior because its welds were stronger: rolled material could delaminate at fractures, whereas hammered material appeared homogeneous.391

Overman’s mid-nineteenth-century account likewise describes sheet made from both charcoal blooms and puddled iron, regarding the former as generally better suited to the task:

The making of sheet iron is a branch full of intricacies and difficulties; 



but once thoroughly understood, it is very simple and agreeable. The 



main difficulty we encounter depends upon the quality of iron from which 



it is made. Charcoal iron generally works well; but some kinds of 



puddled iron do not make good sheet iron. […] Sheet iron was made in 



ancient times by means of forge hammers; it was flattened down by 



broad-faced hammers on large anvils. This method is still practiced in 



the eastern parts of Europe. At the present day, and in our own country, 



sheet iron is rolled. It is made partly from charcoal blooms, and in some 



places from puddled iron. 



a. In all cases where thin sheet iron is to be made, the iron must first be 



converted into flat mill bars. Charcoal blooms, as well as puddled iron, 



undergo the same treatment, with this difference, however , that good 



charcoal blooms do not require a welding heat. 



Puddled iron is to be piled, and a pack of rough bars welded and rolled 



down into flat mill bars. These bars are from four to six inches wide, 



varying in thickness, according to the number of sheets to be made from



them. Heavy sheet iron and boiler-plate are to be made from mill bars, if 



we want a good article. Sheet iron is principally made from charcoal 



blooms shingled down into slabs; sometimes from puddled rough bars, 



piled, welded, and shingled by the T hammer into slabs. By neither 



method is good boilerplate made; a second reheating is, in all cases, to 



be resorted to, if we want the best article the material is capable of 



producing. In the manufacture of sheet iron, our main attention must be 



concentrated upon the quality of the iron, and the power at our service. 



All other matters are of subordinate importance, and have little bearing 



upon the success of our operations. Clean, white, fibrous iron, and a 



surplus of power , are the most essential elements in making good and 



cheap sheet iron.
Overman (1851), pp. 365–366. 392
Redaktionelle Hinweise · 2
  • Die vermeintliche „heterogeneous“-Qualität im Originalkontext ist offensichtlich als örtlich homogen gemeint; entsprechend sprachlich korrigiert.
  • Produktionsmengen und historische Einheiten unverändert; keine nachträgliche Umrechnung oder Ausweitung ihrer geografischen Reichweite.
Originalwortlaut vergleichen
7.4.3 The authenticity testing of armour 



The occurrence of inclusions in the plate-material has been suggested as the strongest factor 



in classifying objects as originals or reproductions. Whenever metallography-testing could 



detect no inclusions, the material was considered to be modern mild -steel and therefore the 



item was a modern reproduction.  



The main problem with such metallurgical explanations is the erroneous assumption that the 



old wrought-iron techniques were not used anymore in the days when reproductions were 



made. Furthermore, it is possible that the metallurgists of old als o produced high quality 



steel – at least locally nearly heterogeneous and free of impurities – by the wrought -iron 



production methods.  



When the authenticity of a certain object  is questioned, the metallurgists should first try to 



determine the method used for the making of the working material. Until today, no research 



on the possible differentiation between the different wrought -iron refining techniques had 



been carried out. 



The basic questions on this concern have also not been answered yet: Are there ne cessarily 



inclusions in iron-plate made from wrought-iron? It is possible that ancient armour plate was 



made from a relatively pure, large bloom without the necessity of being forge-welded? This 



possibility has already been suggested by a finding of  Charles.384 He says that “bloomery 



iron can be very clean, being produced at lower temperatures in the solid state, so that silicon 



is not reduced into the metal phase from silicates in the charge.”385 This means that possibly 



no or only little slag inclusions would be contained. A find of a bloom near 



Trondheim/Norway, C14 dated to the time range between the years 390 -545, delivers 



additional support for this assumption. The bloom was at its outer regi ons almost free of 



carbon, but interiorly it was relatively homogeneous with a carbon content of about 0.7%. It 



contained only few larger hollow spaces, but almost no slag inclusions.386 Furthermore, it is 



also possible that a folding and forge -welding process together with the long -term keeping 



of the material at a white -hot temperature could have led to a complete or nearly complete 



disappearance of the layered structure of mechanically refined iron – at least it is possible 



that such structures cannot be detected by metallography-imaging. In conclusion this would 



mean that armour made from such plate would not show no or only few defect structures  – 



but it would still be genuine.  



On the other hand, some other simple facts suggest that not all armour plate that shows 



impurities must be genuine: Wrought-iron – more precise “puddle-iron” made by the indirect 



process – was produced well into the 20 th century. For example in Donawitz in Austria, the



last puddle-hearth stopped working in 1917. 387 To give some numbe rs on the quantity of 



puddle-iron produced in the times when the making of armour reproduction was at its height: 



The most important device for making wrought-iron was still the puddle-hearth. In the year 



1878 1533 of them produced 24.723.029 cwt of wrough t-iron.388 Actually the production -



quantity of wrought-iron by the same year was still more than twice as high as that of mild 



steel.389 These facts show that wrought-iron (puddle-iron) was the commonly used material 



in the times when presumably the most armour reproductions were made. 



It was also suggested that the chemical composition of “modern”, coal smelted iron -based 



material, would contain sulfur, which in turn was expected to be absent in charcoal-smelted 



“old” metal. It has been suggested that from the  18th century on iron has regularly been 



smelted by coal-charges. This is a mistaken assumption as well, as many 19th century sources 



still mention the use of charcoal as fuel for the blast furnaces. In 1878 in Germany 178 



charcoal operated fineries were producing 446.670 cwt of wrought-iron from scrap-metal390. 



Additionally, the often quoted assumption that forgeries of armour would necessarily have 



to be made of rolled plate becomes questionable when late 19 th century sources still speak 



of thick wrought -iron armour -plate for ships, being produced with the help of machine -



hammers in England. The preferred material was recycled scrap iron. The hammered 



material was considered to be superior to the rolled, as the forge-welding seams were much 



stronger. The res ult was that rolled plate showed delaminations at crack -lines while the 



hammered would appear absolutely homogeneous!391  



A description on the making of sheet -iron shows that by the mid-19th century in England, 



plate was rolled optionally from directly produced iron or from puddle -iron. The directly 



produced “charcoal iron” was considered to produce sheets of better quality: 



The making of sheet iron is a branch full of intricacies and difficulties; 



but once thoroughly understood, it is very simple and agreeable. The 



main difficulty we encounter depends upon the quality of iron from which 



it is made. Charcoal iron generally works well; but some kinds of 



puddled iron do not make good sheet iron. […] Sheet iron was made in 



ancient times by means of forge hammers; it was flattened down by 



broad-faced hammers on large anvils. This method is still practiced in 



the eastern parts of Europe. At the present day, and in our own country, 



sheet iron is rolled. It is made partly from charcoal blooms, and in some 



places from puddled iron. 



a. In all cases where thin sheet iron is to be made, the iron must first be 



converted into flat mill bars. Charcoal blooms, as well as puddled iron, 



undergo the same treatment, with this difference, however , that good 



charcoal blooms do not require a welding heat. 



Puddled iron is to be piled, and a pack of rough bars welded and rolled 



down into flat mill bars. These bars are from four to six inches wide, 



varying in thickness, according to the number of sheets to be made from



them. Heavy sheet iron and boiler-plate are to be made from mill bars, if 



we want a good article. Sheet iron is principally made from charcoal 



blooms shingled down into slabs; sometimes from puddled rough bars, 



piled, welded, and shingled by the T hammer into slabs. By neither 



method is good boilerplate made; a second reheating is, in all cases, to 



be resorted to, if we want the best article the material is capable of 



producing. In the manufacture of sheet iron, our main attention must be 



concentrated upon the quality of the iron, and the power at our service. 



All other matters are of subordinate importance, and have little bearing 



upon the success of our operations. Clean, white, fibrous iron, and a 



surplus of power , are the most essential elements in making good and 



cheap sheet iron.392
S. 199–201 · Sprachlich überarbeitet · Entwurf

7.4.3.1 Earlier investigations

The following examples examine earlier attempts to assess authenticity. No reliable non-destructive method had yet been established for directly dating or provenancing armour sheet, or consistently distinguishing originals from reproductions.

Alan R. Williams examined an unrivalled number of armour objects. His hardness measurements and metallography chiefly concerned material quality, from which he inferred production methods. The scale of this contribution is exceptional, but its interpretation raises methodological questions. Robert D. Smith identified the central problem:

Williams draws conclusions from the analysis of one tiny area on a piece 



of armour and then takes this as indicative of both the whole piece of 



armour and, occasionally, for a whole suit or garniture of armour . Here 



we have an example of technological synecdoche: the implied 



assumption is that the results obtained from that one piece are 



characteristic of the whole. In an attempt to address this issue Williams 



does offer examples of some armours for which he has been able to 



analyze several pieces, in which all the various elements are made from 



broadly similar materials and have broadly similar heat treatments and 



from this he concludes that the analysis from a small sample is indicative 



of all armour production. Whether this is true writ large, though, cannot 



be proved. Medieval and early modern materials in general, and iron 



and steels in particular , are notoriously heterogeneous. Indeed, detailed 



work by this reviewer […] has shown that the surface hardness of a 



single breastplate can vary very widely over its entire surface.
Smith (2004). 393

My own measurements support Smith’s observation. Even a small hand-defence cuff showed substantial variation: five locations along a 100 mm line yielded values from 225 to 363 HV.394 Williams often attributes such differences to varying carbon content. I suggest that forging temperatures, cooling and subsequent heat treatment may instead be important causes. His proposed explanation was not demonstrated by measuring carbon at each hardness-test location, including samples experimentally heat-treated in his research.395

The composition of surviving suits creates another difficulty. Many were repaired or supplemented during use and later, and their present arrangement cannot automatically be treated as the workshop’s original output. Nor is it certain that armourers used material from only one smelt for a suit. Different components could legitimately have different thicknesses and mechanical properties according to their functions.

Contemporary assembly from more than one workshop is also possible, even for costly equipment, particularly when time did not allow a new commission. Metallurgical differences alone therefore cannot establish that components were not originally used together.396

Williams’s article “To what extent can forgeries be detected by metallurgical analysis?” addresses the question explicitly,397 but chiefly presents microstructural observations on seven helmets. It does not establish a systematic distinction between historic and modern material beyond associating slag inclusions with authenticity.

A significant omission is comparative examination of known reproductions. Hundreds of such objects in collections could provide a reference population. If the authenticity of tested objects is assumed rather than established independently, unnoticed nineteenth-century material, including puddled iron, may enter the dataset. General conclusions about medieval material then rest on uncertain classifications.

David Starley also investigated doubtful Royal Armouries objects using hardness, metallography and radiography, the latter to detect concealed modern welds and repairs. Like Williams, he sampled only a few locations. Helmet [ref_arm_5107] PDF, for example, was judged genuine because its one-piece skull consisted of unhardened iron with inclusions and substantial corrosion penetration.398 Why those features could not also occur in a nineteenth-century helmet remained unanswered.

These investigations do not yet resolve the general problem of armour authenticity. The next chapter proposes complementary approaches.

Redaktionelle Hinweise · 2
  • Die pauschale Originalbehauptung, kein heute erhaltenes Ensemble habe seine ursprüngliche Zusammenstellung bewahrt, wurde nicht als bewiesene Gesamtaussage übernommen. Die methodisch erforderliche Einzelfallprüfung bleibt erhalten.
  • Abweichende Härte wird als offene Frage von Zusammensetzung und Wärmegeschichte behandelt, nicht durch eine neue eindeutige Ursache erklärt.
Originalwortlaut vergleichen
7.4.3.1 Preceding approaches 



In the following some specific approaches to the problem of authenticity of armour will be 



introduced and critically discussed. It can be anticipat ed that no reliable non -destructive 



method, neither for differing between original and reproduced iron -based plate nor for any 



direct dating or provenancing, had been found yet. 



Only one metallurgist carried out analysis on a huge number of armour parts: A lan R. 



Williams. He was frequently testing the material quality only – by hardness tests and by 



metallography-imaging. From the data revealed, Williams drew conclusions on the 



material’s manufacture processes. His knowledge and the amount of items tested by him are 



absolutely unrivaled. Nevertheless his approaches are not unproblematic. The basic 



problems concerning the metallurgical recognitions in Williams’ studies were described by 



Robert D. Smith: 



Williams draws conclusions from the analysis of one tiny area on a piece 



of armour and then takes this as indicative of both the whole piece of 



armour and, occasionally, for a whole suit or garniture of armour . Here 



we have an example of technological synecdoche: the implied 



assumption is that the results obtained from that one piece are 



characteristic of the whole. In an attempt to address this issue Williams 



does offer examples of some armours for which he has been able to 



analyze several pieces, in which all the various elements are made from 



broadly similar materials and have broadly similar heat treatments and 



from this he concludes that the analysis from a small sample is indicative 



of all armour production. Whether this is true writ large, though, cannot 



be proved. Medieval and early modern materials in general, and iron 



and steels in particular , are notoriously heterogeneous. Indeed, detailed 



work by this reviewer […] has shown that the surface hardness of a 



single breastplate can vary very widely over its entire surface.393 



The author of this paper by own e xperience supports Smith’s statement concerning the 



varying hardness of one item. Even at the comparatively small surface of a certain hand-



protection-cuff the measured hardness was found to vary  widely.394 Williams frequently



considers the varying carbon co ntent of a presumably heterogeneous material to be 



responsible for the varying hardness. The author of this study suggests that it is rather the 



varying heat treatment while the armour was forged, the natural cooling or possibly the 



tempering method that r esulted in different hardness -properties at different locations. 



Williams never proved his theory despite it would have been an easy task to test the carbon 



content at the location of the hardness indentation – particularly at the samples of old armour 



plate he destructively heat-treated to subsequently test their hardness.395 Furthermore, there 



is no suit of armour existing today which supposedly left the armourer’s workshop in the 



current composition. Nearly all suits had been repaired and/or completed in the times of their 



use and after. It is also not sure that the armourers, when making a complete suit, used only 



iron of one smelt – and the properties of iron -based material might be different from smelt 



to smelt. Alan Williams frequently ignored these facts and drew conclusions on the whole 



armour by examining only one spot or part. It is not very meanin gful if the results of 



metallurgical testing differ from part to part. Each part of a suit had different purpose and 



could therefore also be designed from plates of different thicknesses and/or with different 



mechanical properties. Research on the topic is also not established far enough to tell if not 



also costly armour could have been assembled contemporarily from different workshops. If 



time was too short for the making of a suit made-to-measure, the combatant certainly did not 



go into battle without armour. It is therefore generally questionable to define parts of a suit 



of armour as not originally belonging, on the basis of differences in their metallurgy.396 



Only one of Williams’ numerous articles seems to deal with the problem of authenticity. The 



title “To what extent can forgeries be detected by metallurgical analysis?” promises to shed 



some light on the question of authenticity by metallurgical testing.397 Its content totally fails 



to answer any question on the topic. It is just a collection of his comm on metallography-



analysis, telling about the mechanical properties of seven helmets. Williams does not 



mention any other expected difference between modern and “old” iron or steel than that 



samples which contain slag inclusions must be genuine.  



The most lamentable omission of all metallurgical approaches in Williams’ works is that no 



attention is paid to the metallurgy of reproductions. In various collections there are hundreds 



of items that are considered to be reproductions, available for testing. These could provide a 



good basis to start from. The authenticity of the tested specimen in Williams works is usually 



not questioned and therefore the revealed data might be falsified by the coincidental and 



unrecognized testing of modern material, like puddle -iron. As long as this question is not 



comprehensively answered, also the general conclusions on ancient material -properties 



stand on a weak basis.  



Another scientist, David Starley, carried out some authenticity -testing on questionable 



objects of the Royal A rmouries in Leeds. He tested microstructure and hardness, and like 



Williams he revealed information on few spots only. Additionally the items were X-rayed to 



detect hidden modern welding seams etc. For example the helmet [ ref_arm_5107]398 was 



found to be genuine as the skull was made of one piece of not hardened iron-plate that shows



inclusions and significant corrosion penetration. The question why the same properties 



should not be found at a helmet made in the 19th century remained unanswered. 



The aforesaid approaches had not significantly forwarded the topic “authenticity questions 



on plate armour”. In the following, some suggestions for different approaches will be 



discussed.

8 New approaches to the attribution of plate armour

S. 202–203 · Sprachlich überarbeitet · Entwurf

8 New approaches to the attribution of plate armour

Attributing armour to a place, maker or period depends on several kinds of evidence. Observations should be distinguished from interpretations. Technical and stylistic features can be recorded, classified and compared through humanities-based and scientific methods, but a single observation seldom establishes an attribution. Conclusions drawn from them should retain an appropriate degree of uncertainty.

Handling more objects develops a sense of what may be genuine or doubtful, but intuition should not determine a final judgement. An open assessment is preferable to an unsupported rejection. Otherwise, suspected objects may be neglected. A conservator at the Palazzo Venezia in Rome told me that, about twenty-five years earlier, a specialist had selected supposed reproductions from the Odescalchi collection’s stores.399 His reasons were not recorded. The rejected objects subsequently remained unpublished, dusty and corroding. Several appear likely to be genuine [ref_arm_2828] PDF; others have additions or alterations, such as [ref_arm_3714] PDF, whose thoracic plate may be its only original component.

Premature rejection can distort the historical record. Moreover, a well-made reproduction is itself a work of craftsmanship and evidence for the history of armour-making. A deceptive purpose does not erase the skill involved, even if copying requires less invention than designing an original. Reproductions belong to the history of the subject and merit conservation and clearly labelled display.

Two centuries of reproduction demonstrate armour’s continuing fascination and importance in European material culture. Its flourishing manufacture between 1350 and 1650 contributed significantly to craft development and the conditions preceding industrialisation. During the following century and a half, production contracted chiefly to simple breastplates and helmets, allowing much practical knowledge to disappear.

Museum visitors and readers can appreciate reproductions when they are identified as such. Explicit uncertainty likewise reveals the questions that remain and the need for further research. The following sections propose ways in which particular features can support attribution.

Originalwortlaut vergleichen
8 Suggestions for new approaches to the mapping of plate armour 



As said above, many different factors influence the mapping of armour to a production site, 



a producer’s name and the production time. The reasons for such a mapping should be split 



into two categories: suggestions and facts.  The facts derive from the observation, 



classification and comparison of technical and stylistic details. They could be provided by 



methods used by humanities and by natural scientific disciplines. A single fact is usually not 



enough to allow a final mapping. The conclusion on certain facts should be of a suggestive 



character.  



The more armour pieces the scholar had in his hands the more he will become aware of what 



might be genuine and what is doubtful. Nevertheless, this “feeling” should not influence a 



final judgment. It is better to leave the expertise open than to condemn an object to be a fake 



or a reproduction, even though doubts might remain. Wherever this advice is not regarded, 



the suspected armour parts were left neglected and without conservation in the shelves. This 



happened for example to some items of the Collezione Odeschalchi, now in the Palazzo 



V enezia in Rome. The author of this paper was told by the restorer of the collections that 



some 25 years ago a scholar of arms and armour 399 was asked to go through the storage 



rooms and to sort out what he considered to be reproduced – and so he did. The reasons for 



this specialist’s decisions have not been documented. The objects rejected by his judgment 



are ever since lying unpublished, dusty and rusted in a shelf. Many of these items are most 



likely genuine [ ref_arm_2828], just some are for sure completed [ ref_arm_3714] (only 



thorax-plate genuine?) or otherwise altered.  



Many specialists are too quickly at hand with their final judgment. But what if the objects 



defined as reproductions are indeed original? It is very dangerous to give statements of which 



the specialist cannot be a hundred p ercent sure. Actually this makes possible that historical 



facts get  altered. The approach of sorting out and neglecting armour parts is even more 



questionable when considering that a good reproduction is an artwork of its own right and a 



document of the history of a rmour-production itself. Even if the purpose of its production 



was to deceive a potential buyer, it does not make the artwork itself a bad thing. The skills 



necessary to make an exquisite copy of a historical model are the same the ancient armourers 



must have possessed. The only difference is that the simple copying requires no creativity.  



Nevertheless, the existence of fakes and reproductions is a fact that belongs inseparably to 



the history of armour production. Can it be good to let the “bad fakes” rust unattended in the 



storage? Would it not be fair to show them to the interested museum visitor, so he can also 



understand the difference between a copy and an original?  



That for at least the past 200 years armour was reproduced, shows that it is of timele ss 



fascination for many and it shows the importance it has for the material -culture of Europe. 



The 300 years of flourishing armour production in Europe between 1350 and 1650 play a 



significant role in the development of European crafts and thus for the conditions that led to 



the industrial revolution. The roughly 150 years between 1650 and 1800, when armour 



production was reduced to simple torso front -protections and helmets, are responsible for 



the huge loss of knowledge about its traditions.  



The visitor of a museum or the reader of a book wants to see or learn about objects of art. If 



these objects are armour parts, then he would also love to see the reproductions, as long as 



the book or the showcase label defines them as such. He also would not mind if h e found 



many question marks behind any statement. Even more, such an approach shows the



interested lay that there are still a lot of unanswered questions on the topic. This is the best 



justification for the necessity of further research. 



In the following, suggestions will be made how certain details can help to map extant armour 



to different aspects.
S. 203–204 · Sprachlich überarbeitet · Entwurf

8.1 Dating reference points

Reliable dating requires secure reference points. Few surviving armour objects come from documented excavations; most remained above ground. Dating has therefore depended chiefly on stylistic comparison with depictions. By the early nineteenth century, scholars recognised that many late medieval and Renaissance images closely represented real equipment. Rivets, plate relationships and articulated lames often correspond to surviving objects and could function if reconstructed in three dimensions. Such images can record equipment in current use, in fashion or at least still familiar to the artist.

Few late medieval artworks bear a maker’s exact date, although documentary and art-historical research can sometimes establish one securely or with high probability. Before using a dated image as evidence for armour, four questions must be considered: Is the work contemporary, reproduced or substantially restored? Does it show imaginary equipment? Was the depicted armour fashionable when the work was made? Or was it already old-fashioned?

Armoured effigies are particularly valuable but insufficiently studied. Their detail often suggests use of actual armour as a model. The monument of Count Otto IV of Henneberg (d. 1502) in Römhild’s town church, probably cast by Peter Vischer the Elder (1460–1529), is modelled on every side and even has a removable helmet.400

A date of death on a monument is not automatically its date of manufacture. Some effigies were commissioned during the sitter’s lifetime,401 potentially long before death. Others were made much later because death was unexpected or finances and politics delayed the commission. In the latter case, the relationship between the represented armour and the deceased’s actual equipment is uncertain.

The artist might depict armour worn near death or during an earlier period of achievement. Someone dying in old age might no longer possess fashionable equipment. Bills and commissions occasionally narrow the monument’s production date. In other cases, a range of roughly twenty years either side of death is proposed here as a working estimate, not a guarantee that the armour itself was made within it.

Even a faithful depiction of the deceased’s own armour need not show a recent purchase. Not every noble could continually replace equipment, and useful armour was not discarded simply because fashion changed. The artist might also have used another person’s armour. Commemorative patrons generally wanted their best and most current appearance represented; idealisation could therefore affect the evidence, despite social constraints on overstating status.

Fifteenth-century depictions nevertheless show rapid stylistic change, especially north of the Alps. A design agreed at commission might already appear dated by delivery weeks, months or years later. Ridges in many forms played a major decorative role, whereas Italian makers generally experimented more conservatively.

Chronological ordering of such visible features commonly permits dating within a span of about twenty years, but seldom to a particular year or month. Technical details—turned edges, ridge profiles, embossing, decoration, finishes, forming methods, thickness, rivets, washers, fastenings, applied fittings and marks—have not previously been classified and sequenced comprehensively. Establishing their periods of use, as proposed earlier, may refine these estimates.

Redaktionelle Hinweise · 2
  • Die Originalfolgerung, das Herstellungsdatum der dargestellten Panzerung müsse innerhalb der Datierungsspanne des Denkmals liegen, widerspricht den unmittelbar genannten älteren Vorlagen. Die Neubearbeitung trennt beide Datierungen ausdrücklich.
  • Die Spanne von etwa 20 Jahren bleibt eine Aussage der Dissertation, kein allgemeines Genauigkeitsversprechen.
Originalwortlaut vergleichen
8.1 Dating reference 



To allow a determined dating of objects of art, it is important to define stable basing points. 



Comparatively few armour pieces were excavate d; many more were always kept above 



ground. Thus, not much reliable archaeological data for dating plate armour is at hand. 



Extant plate armour was so far mainly dated by stylistic criteria. These criteria were 



developed by comparisons to depictions of arm our in artworks. Already by the early 19 th 



century it became clear for the students of the topic that most of the late medieval and 



renaissance artworks were detailed reproductions of contemporary real existing objects. The 



technical features of armour sho wn on sculptures, drawings, engravings, miniatures and 



paintings would usually function, if transferred to a three dimensional object. Rivets are at 



the right spots, lames are shown in the correct positions, just as they are found on extant 



armour pieces. Even superficial comparisons proofed that many artworks are most likely eye 



witness reports of what contemporarily was in fashion or in use, but at least what was still 



known. 



In the late medieval period, not many of the concerned artworks carry an exact date attached 



by the producer. In some cases art historians were able to date objects with definite or highly 



probably accuracy. These are the most important basing points for delivering reliable dates 



to extant plate armour. Examples found in more or less reliably dated artworks still have to 



be examined on four aspects before they are taken for dating extant armour. The questions 



to be asked are: 



- Is the artwork contemporary, maybe a reproduction or heavily altered by restoration? 



- Does the artwork maybe show fantastic items which did contemporarily probably not 



exist? 



- Is the armour shown of the latest fashion of the moment the work was finished? 



- Was the armour already old fashioned in the moment the artwork was produced? 



Especially effigies which show the full armoured deceased are important for dating armour. 



This field has nevertheless not been studied sufficiently enough to deliver satisfactory 



answers. On such sculptures it usually seems very likely that the sculptor used an existing 



suit of armour as a model. Monuments like the one of grave Otto IV . of Henneberg (†1502) 



in the city church in Römhild, probably cast by Peter Vischer the elder (*1460; †1529), 



suggest this assumption, as it is embossed at all sides and the helmet can even be det ached 



like its real iron model.400  



Commemorative or tomb stones and brasses often have the date inscribed when the deceased 



had passed away. Taking this date uncritically for dating the depicted armour is not advisable. 



This date is not connected to the completion of the artist’s work. Effigies were often made 



in the lifetime of a person401, and thus they could only show what contemporarily existed. If 



the purchaser had a long life after the finishing of his stone or cast, the date of death would 



not fit to the fabricati on of the shown armour. In some cases the monuments were finished



long after the death of the commemorated person. This happened especially if the one passed 



away unexpected or the momentary financial or political situation did not allow an 



immediate realization of the project. In such a case it would be  questionable if the sculptor 



still used contemporary armour as model for his work.  



Also problematic is the determination of the armour as the one the deceased used when he 



passed away or is it of the times  when he had his most success. If he died of old age it is 



unlikely that he still owned up to date armour, so he was probably depicted in his old 



equipment. In some cases, extant written documents like bills or orders helped to narrow the 



exact production date of an effigy or monument.  



Nevertheless, the date of the production of an effigy is usually to be estimated within a period 



of at most plus or minus 20 years around the death of the depicted. This means that the 



production date of the armour would also lie within this period.  



Generally the possibility for an exact dating of armour should not be overestimated. Given 



that the deceased was actually shown in his own armour, it still does not mean at all that it 



was produced shortly before his death. Not a ll nobles could afford to be permanently 



equipped with armour of the latest fashion. Armour was not simply thrown away just because 



it was old and it cannot be stated with certainty that the sculptor even used armour as model 



which did actually not even be long to the depicted. Of course , it is unlikely that medieval 



social norms would accept an exaggeration of the actual status of the deceased. Anyway, 



benefactors generally wanted to be depicted with their best and most up to date wear, and 



modesty was cert ainly out of place at contemporary commemorative artworks. This could 



have led to some conscious shifting of the facts on the contemporary appearance. 



According to contemporary depictions, fashion was actually rapidly changing throughout 



the 15th century. The fashionable stylistic features an armourer proposed to his client when 



discussing an order might have been already antiquated weeks, months or even years later, 



when he delivered his products. The style of complete suits changed very quickly from the 



beginning of the 15th century, especially in the regions north of the Alps. Mainly the ridge – 



in all facets – was used to design the plate surfaces. The Italian producers were rather modest 



with the application and the experimenting of new decorative features.  



The easily visible changing of fashion now helps modern scholars to date armour. Stylistic 



details had been observed and brought into a chronological order. It is therefore possible to 



date most of the extant armour pieces within a range of 20 years at most. These methods are 



usually unquestionable so far, but it is usually not possible to exactly date armour to the year 



or even the month of its production. The development of the different types of turned edges, 



ridges, embossing, plate decorations, surface finishes, shaping techniques, plate-thicknesses, 



rivets, washers, fastening systems applications and marks have not been classified yet and 



thus they had not been ordered chronologically before. The attempt proposed above of 



defining a utility time of certain features might help to closer date extant items.
S. 204–207 · Sprachlich überarbeitet · Entwurf

8.2 Attribution through marks

Identifying makers and their lives is a central concern in art history. Armour, however, was never consistently signed. Even the earliest surviving objects sometimes carry stamped marks, yet marking remained irregular through the mid-seventeenth century, including on work of the highest quality. Polishing may have erased some marks, but most surviving objects were probably never marked. Where marks remain, wear or unfamiliar symbols may prevent interpretation. Documentary names can occasionally be connected with objects through a maker’s seal or heraldic device.

Marks can indicate makers, owners, regions or towns, but interpretation requires extensive archival work. Research over the past 150 years has identified many armourers, including fifteenth-century names from Milan, Brescia, Augsburg, Nuremberg, Landshut and Innsbruck. The sole dedicated monograph cited here, published in 1959,402 is of limited practical use because its illustrated marks are not tied to surviving objects.

The Royal Armouries Library preserves the “de Cosson Index”: boxes of manuscript cards recording marks on arms and armour worldwide, compiled by Charles Alexander Baron de Cosson (1846–1929). They include material intended for an unpublished dictionary. Selected marks also appear in handbooks403 and collection catalogues.404 Researchers must still consult these scattered publications. Lionello G. Boccia contributed particularly to Italian identifications; Wendelin Boeheim and Bruno Thomas to German ones.

Eugene Heer’s three-volume “Der neue Støckel” records 6,500 gunsmiths’ and crossbow makers’ marks but excludes armourers. Comparison remains worthwhile because different trades sometimes used similar signs, potentially revealing relationships between specialisms.405 Most armour marks probably remain unidentified.

Documented production outside the best-known centres raises further questions. Munich, Regensburg, Stuttgart and Pforzheim all had fifteenth-century armourers, yet no surviving objects had been securely assigned to them in this study. In 1478, Lower Austrian arsenal official Wilhelm Tentsch bought armour from a “harnascher” in Freiburg, although the document does not establish whether this was Freiburg im Breisgau or Fribourg in Üechtland.406 Pierre Terjanian’s study of a fine helmet probably made in Basel demonstrates the potential of less-studied centres.407 Unexamined records elsewhere may connect anonymous objects with named makers. The seal of the Viennese master Kristan survives, for example, but has not been identified on armour [ref_ill_art_5371] PDF.

Comprehensive archival investigation lies beyond this dissertation. A structured database could nevertheless make comparison far less laborious. Marks should first be classified by their possible function: maker identification, quality approval or ownership.

A maker’s mark serves as a signature or brand. It may give a name—“Innocens” for Pier Innocenzo da Faerno [ref_arm_2215] PDF—an abbreviation, such as “casp” for Caspar Rieder [ref_arm_3374] PDF, or initials. Speaking symbols can allude to a surname, such as a wheel for “Wagner” (wagon-maker). These are particularly common in German-speaking regions. The Augsburg Helmschmied family sometimes used a tournament helmet surmounted by a cross [ref_arm_3401] PDF.

Italian initials may appear beneath a cross with a split lower arm [ref_arm_781] PDF [ref_arm_3097] PDF (“GIS”, possibly Giovanni da Salimbeni), a crown [ref_arm_1353] PDF, or an abbreviation line with a central rise [ref_arm_2119] PDF. Crowned letters also occur north of the Alps [ref_arm_1724] PDF. Marks formed from several chiselled strokes constitute a distinctive Spanish group [ref_arm_3153] PDF; some variants may have been applied with one punch [ref_arm_24] PDF. These are interpreted as workshop marks. “Arbois”, stamped on [ref_arm_3570] PDF, identifies the French town where Italian armourers established a workshop in the late fifteenth century.

Quality marks were applied after inspection by a civic authority or guild. Examples include Augsburg’s pine cone [ref_arm_282] PDF, Landshut’s hat [ref_arm_1890] PDF and Nuremberg’s arms [ref_arm_3421] PDF. These are the three cities known here to have required such approval marks; no equivalent Italian civic practice is identified.

Some approval marks occur inside plates, perhaps to protect them from grinding after preliminary inspection. From the early sixteenth century, suppliers at powered hammers may also have marked prepared blanks. Internal marks are rare before 1500; the examples identified here are [ref_arm_3867] PDF and [ref_arm_3698] PDF.408 Early sixteenth-century breastplates [ref_arm_3423] PDF [ref_arm_3568] PDF bear unclear internal marks, possibly an N within a beaded circle.

Ownership marks include engraved or chiselled Arabic signs on objects from Ottoman arsenals [ref_arm_1064] PDF [ref_arm_1063] PDF. European examples include a supposed Venetian winged lion [ref_arm_2132] PDF, the Habsburg “Bindenschild” [ref_arm_3527] PDF and the Matsch arms [ref_arm_1495] PDF. Nineteenth-century museums also marked objects with their full names, as in Brussels [ref_arm_3350] PDF and Paris [ref_arm_3199] PDF. Many Munich Stadtmuseum objects carry a lead seal riveted through a hole, with an inward-facing stamp showing the city’s monk and the letters KBLWM, probably referring to the royal Bavarian Landwehr.409

Marks should also be classified by what they depict. Letters may be upper- or lower-case, Roman or Gothic, abbreviated [ref_arm_1978] PDF or spelling complete words. Symbols include crosses [ref_arm_1512] PDF, split crosses [ref_arm_2048] PDF, crowns [ref_arm_612] PDF, helmets [ref_arm_1743] PDF and fleurs-de-lys [ref_arm_1348] PDF. Heraldic arrangements occur on [ref_arm_1521] PDF [ref_arm_1929] PDF [ref_arm_1724] PDF [ref_arm_880] PDF. Other stylised motifs include fleurs-de-lys [ref_arm_1710] PDF, bovine heads [ref_arm_2081] PDF [ref_arm_1712] PDF, blossoms [ref_arm_1769] PDF [ref_arm_2148] PDF and animals [ref_arm_3430] PDF. Each can be recorded as recessed or raised.

Position matters too, since makers seem to have favoured particular locations. Several functions and motifs may coexist on one object; Italian plates often carry grouped marks, including three arranged as a triangle.

For future comparison, I propose recording marks through thin-paper rubbings scanned with a scale reference. Stored in a database, these images could be compared by form and dimensions. Hundreds of rubbings collected during this project could form the basis of such a resource.

Redaktionelle Hinweise · 2
  • Freiburg im Breisgau ist im Originalhaupttext voreilig festgelegt; die bereits in Anm. 406 genannte Alternative wird hier auch im Haupttext erhalten.
  • Historische Museumsbezeichnungen und Lesarten von Marken bleiben Quellenangaben. Keine neuen Werkstattzuweisungen.
Originalwortlaut vergleichen
8.2 Mapping with the help of marks 



The question on the name and the life of artists or craftsmen is probably one of the most 



central one s for any research on historical artworks. In parallel to all medieval art, the 



contemporary armour is not consequently signed by symbols, letters or signatures that could 



allow the identification of the maker’s name. Even though the earliest pieces occasio nally 



already bear stamped marks, until the end of the great period of armour in the mid-17th 



century the marking of the plates did not become common at all. Even objects of the highest 



quality were not consequently marked. Some marks might have disappeared from polishing, 



but certainly the largest part of extant objects was not marked. Even where objects were 



marked, the symbols often cannot be identified, either because they are nearly vanished or



because the meaning cannot be understood. Sometimes the na mes of armourers found in 



written documents can be attributed to certain pieces, if their seal on the documents or their 



coat of arms etc. is known and can be found stamped into a certain armour piece.  



The topic of the interpretation of marks and the poss ibilities of identifying the master, the 



former owner, the production region or city is a vast field. The identification of marks is very 



important for any approach to the understanding of the armourer’s art, but it requires intense 



archival research. In the last 150 years research brought to light the names of many armourers 



throughout Europe. For the 15th century, the names of the armourers appearing in historical 



documents of the cities of Milan, Brescia, Augsburg, Nuremberg, Landshut and Innsbruck 



were published. The only monograph on the topic was published in 1959402. This book is of 



little use for the scholar, as none of the included illustrations of marks is referring to any 



extant object. In the library of the Royal Armouries in Leeds there are several cartons full of 



hand written record cards describing marks on all kinds of extant arms and armour all over 



the world. This records were collected by Charles Alexander Baron de Cosson (*1846; 



†1929) in the 19th and early 20th century and is known as the “de Cosson Index”. They also 



contain manuscript-like information that was sought to be published as a dictionary for arms 



and armour, which was never realized. Several handbooks 403 or collection -catalogues404 



include lists of a choice of marks. Until today it i s such single publications that need to be 



studied when questions on marks arise. Many marks were already identified or at least 



suggestions on their identification were published. The identification of marks on Italian 



armour is merely due to Lionello G. Boccia, on German armour it is merely due to Wendelin 



Boeheim and Bruno Thomas. The 3 volume-publication “Der neue Støckel” by Eugene Heer 



comprises 6.500 marks of gunsmiths and crossbow makes marks but no armourer’s marks. 



It is also important to compare the marks published by Heer with armourer’s marks as marks 



of different craft -branches often show similarities to each other. Future studies may help 



finding new relationships between different specialized crafts. 405 The author estimates that 



the larger amount of the existing marks still has to be identified.  



One important question is, where all the armour went that was evidently produced in the less 



famous production centers. Contemporary documents of cities all over Europe proof the 



existence of armourer’s  workshops not only in Innsbruck, Augsburg, Nuremberg and 



Landshut. In the 15th century armourers were working for example in Munich, Regensburg, 



Stuttgart, Pforzheim etc. For example the city of Freiburg im Breisgau was probably also a 



production center f or armour production. The “Zeugwart” for Lower Austria, Wilhelm 



Tentsch, bought armour there from a “harnascher” in 1478.406 Not a single object of the 15th 



century has yet been identified with one of the said cities. Pierre Terjanian, in his essay on a 



high quality helmet made most likely by a Basel armourer, showed that there is still new 



information to be found on the armourers of the less popular centers407. Certainly documents



of other central and western European countries survived and have simply not bee n viewed 



yet. It is possible that in the future anonymous objects might be identified with their master. 



Private seals of armourers are still extant but they have not yet been found on any item – for 



example the seal of the Vienna master Kristan [ref_ill_art_5371].  



Within the range of this study it was not possible to focus on the aforesaid aspects 



comprehensively. To ease further studies of marks, some suggestions for their classification 



will be introduced in the following.  



A computer-aided comparison of data on marks entered into a database could allow revealing 



numerous kinds of interrelations between different objects – up to now an arduous Sisyphean 



labor. Marks can be classified by several aspects. The first aspects are concerning the 



intention of the marking: 



Producer identification:  



The mark is the personal sign of the armourer and serves like his signature or in modern 



words: it is his brand. It can consist of whole names (“Innocens” for Pier Innocenzo da 



Faerno [ref_arm_2215]) abbreviations (“casp” for Caspar Rieder [ref_arm_3374]) or initials 



stamped in different fonts. Also symbols that refer self-explanatory to the name of the maker 



were used (e. g. a wheel for the name Ger. “Wagner” Engl. “wagon-maker”). Such symbols 



are merely used in the German speaking lands. For example the Augsburg armourers of the 



Helmschmied family occasionally signed their works with a jousting helmet with a cross at 



the crest (e.g. [ ref_arm_3401]). Initials on Italian armour are often surmounted by either a 



cross with the lower branch split in two halves [ref_arm_781] [ref_arm_3097] (“GIS” for 



Giovanni da Salimbeni? ), by a crown [ ref_arm_1353] or by an abbreviation line with a 



central bump [ref_arm_2119]. The crown upon a letter also occurs on northern alpine armour 



[ref_arm_1724]. A group of its own is fo rmed by symbols consisting of several single 



chiseled lines, found exclusively on armour made in Spain [ref_arm_3153]. Some variations 



were maybe applied with a single stamp [ ref_arm_24]. These marks are considered to be 



workshop’s marks. A unique workshop identification is the stamping of some items with the 



word “Arbois”, the name of the French city where Italian armourers had established a 



workshop by the end of the 15th century [ref_arm_3570].  



Quality control:  



The mark is attached to good quality items after an inspection on behalf of an administrative 



authority, usually the city-council or the armourer’s guild. Such a mark can either show the 



city’s symbol (Augsburg: pine -cone [ref_arm_282], Landshut: hat [ ref_arm_1890]) or the 



coat of arms (Nuremberg [ref_arm_3421], late 15th century). It is also only these three cities 



that are known to have implemented this quality -approval by means of a mark. The Italian 



cities made no use of it.  



Also interior approval -marks are found. The mark is stamped to the interior of an item to 



prevent it from being ground of. It was probably attached after a first quality inspection 



before the item was ground and polished. It is possible that from the early 16 th century on 



these marks were attached by the workers of a waterpowered hammer who delivered semi-



finished plates in the right dimensions to the armourer’s workshops. Such interior marks are 



rarely found at armour before 1500. The only earlier items the aut hor could find are 



[ref_arm_3867] [ ref_arm_3698].408 In the early 16 th century, some breastplates were



stamped interiorly [ref_arm_3423] [ref_arm_3568] (at both items not clearly identifiable: a 



letter in a ring of pearls, N?) 



Owner identification:  



Items stored in the Imperial Ottoman arsenals were often marked with an Arabic symbol (e. 



g. [ ref_arm_1064] [ ref_arm_1063]) engraved or chiseled into the plate. Some central 



European arsenals marked their items with a stamp: V enice, [ref_arm_2132] (said to show a 



winged lion); Zeughaus of the Habsburg family, a “Bindenschild” [ref_arm_3527], early 16th 



century; Matsch family, coat -of-arms [ ref_arm_1495]. Also modern owner’s marks are 



found at several items. For example in Bruxelles the Museé d’Antiquites [ ref_arm_3350] 



and in Paris the Museè d’Arte [ref_arm_3199] in the 19th century had stamped several items 



with the full name of the museum. Also many items in the Stadtmuseum Munich have a lead 



seal riveted into a hole, stamped interiorly with the monk – the city’s symbol – and the letters 



KBLWM (probably Königlich Bayerische Landwehr München)409.  



A single mark can be classified by aspects concerning its depiction. There is a great variety 



of symbols and letters stamped into the plates. Actually there are no restrictions: 



Letters (in capitals or in lower cases, in Antigua or in Gothic Print), sometimes with 



abbreviation lines [ref_arm_1978], sometimes spelling whole words. 



Crosses [ ref_arm_1512], split crosses [ ref_arm_2048], crowns [ ref_arm_612], helmets 



[ref_arm_1743], fleur-de-lys [ref_arm_1348] etc. 



Coat-of-arms-like arrangements: [ ref_arm_1521] [ ref_arm_1929] [ ref_arm_1724] 



[ref_arm_880]. 



V arious stylized objects are found at armour made in Italy and the German s peaking 



countries, e.g.: fleur -de-lys [ ref_arm_1348] [ ref_arm_1710]; cow’s head [ ref_arm_2081] 



[ref_arm_1712] Armour); blossom [ref_arm_1769] [ref_arm_2148], animal [ref_arm_3430] 



etc.  



Each symbol can further be defined as recessed or embossed. 



The position of the mark at the object should be considered, as the armourers seem to have 



preferred to mark their objects at more or less the same position. 



Nearly all classes can occur combined on one object, especially as occasionally several 



marks can be stamped into one item. On Italian armour commonly a group of marks is found, 



often three marks form a triangle.  



To ease the comparison of marks, the autho r additionally suggests developing a supportive 



method for the identification of marks in the future. The marks could be rubbed on a thin 



paper directly from the objects. The rubbings are scanned together with a size -reference (e. 



g. a transparent scale-paper). These scans stored in a database can be used for computer aided 



comparisons to reveal marks with similar dimensions. The author of this paper has already 



collected hundreds of mark-rubbings that could serve as the basis for such a mark-database.
S. 207–209 · Sprachlich überarbeitet · Entwurf

8.3 New observations on marks

A distinctive mark type deserves attention: round lead seals attached to nineteen fifteenth-century objects in the Munich Zeughaus, including [ref_arm_3656] PDF.410 Wackernagel mentioned them only briefly in 1982 while describing a different monk mark stamped directly into metal.411 These seals are the only examples of their type identified on armour of the period studied here.412

Each occupies a drilled hole. Some may reuse an earlier opening: [ref_arm_1801] PDF has a nearby empty hole that could once have formed a pair. Reuse might have avoided further alteration. The stamp faces inwards, probably to protect the soft lead, but many impressions are damaged. On [ref_arm_2412] PDF the design remains clear: a monk looking to his right, wearing a broad hooded garment, with KBLWM around his feet.

The letters may stand for “Königlich Bayerisches Landwehr Museum” or “Königlich Bayerische Landwehr München”. Between 1865 and 1869,413 the royal Bavarian Landwehr maintained the arsenal.414 Munich’s traditional monk also appears with broad sleeves on the 1866 guide cover [ref_ill_art_5393] PDF.415 The sealed objects may have been those Braun selected for display in the Landwehr Zeughaus.

The seals presumably predate the Landwehr’s dissolution by the Bavarian king in 1869. From 1870 the BNM administered the arsenal.416 One of the nineteen marked objects remains there [ref_arm_1798] PDF.417 Some Munich objects were lent to the BAM in Ingolstadt in the 1920s or 1930s. Their origins were later forgotten, and acidic cleaning removed some accession numbers. Returns to the Stadtmuseum began in 2012.418

Italian makers shared conventions in marking as well as style: letters below a crown, split cross or abbreviation line are often treated as evidence of Italian origin. The possibility that other regions imitated these marks to benefit from Italian armour’s reputation has received little attention. Comparable deception is well known among blade makers.419 Later collectors’ markets also encouraged forged makers’ or civic marks on both genuine and reproduced plates. The reproduced suit [ref_arm_4128] PDF, for example, has a German-style Type VII helmet bearing an Italian-style mark.

Some reproduction makers may instead have marked their work to identify it openly. If Schedelmann correctly attributes the reproduced work in suit [ref_arm_4141] PDF to Leopold Winkelmayer,420 the stylised W below the nape opening of its backplate [ref_arm_3349] PDF may be his mark. Similar stamps could connect [ref_arm_1899] PDF [ref_arm_1857] PDF and chin-and-throat defence [ref_arm_3202] PDF with his workshop. The unmarked [ref_arm_3194] PDF closely resembles that defence and the one associated with the Altena suit [ref_arm_3172] PDF in form and size, making a common origin plausible.

Redaktionelle Hinweise · 2
  • Anm. 410 behauptet weitere spätere Stücke mit dem Siegel, während Anm. 412 deren Prüfung als zeitlich nicht möglich beschreibt. Umfang des tatsächlich untersuchten Bestands klären.
  • Die Zuschreibung an Winkelmayer bleibt bedingt. ref_arm_4141 enthält laut früherem Kapitel auch einen echten Helm; deshalb nicht erneut pauschal als vollständig reproduziertes Ensemble bezeichnet.
Originalwortlaut vergleichen
8.3 New recognitions on marks 



The author wants to draw the attention to a unique type of mark that has not been described 



so far: The round lead seals attached to 19 15th century410 items (e. g. [ref_arm_3656]) of the 



Munich “Zeughaus”. Wackernagel made only a short note of them in his 1982 catalogue,



while he described another monk-mark found stamped directly into the armour plate.411 The 



lead marks are important, as they are the only marks of this type found o n extant armour of 



the concerned period.412 The lead seal is always fixed in a hole drilled into the plate. In some 



cases, it seems like older holes of other purpose were used, as a second “empty” hole of a 



possible former pair is visible close to the seal [ ref_arm_1801]. Maybe it was tried to use 



existing holes to keep the genuine object untouched. The symbol is always stamped 



interiorly, probably to prevent the soft lead from damage. Nevertheless, at many objects the 



stamping is badly spoilt, but it can be seen still very clearly for example at [ref_arm_2412]. 



The symbol resembles in its center a monk looking to his right, dressed in a wide, caped 



coat. To his feet the seal is encircled by the letters KBLWM. The letters might stand for 



“Königlich Bayerisches Landwehr Museum” or alternative for “Königlich Bayerische 



Landwehr München”. From 1865-1869413 the Zeughaus items were maintained by a citizen 



militia, the “Königlich Bayerische Landwehr”.414 The monk is the traditional symbol for the 



city of Munich and a monk with wide sleeves also covers the museum guide of 1866 



[ref_ill_art_5393].415 The marked objects of the inventory were possibly those chosen by 



Braun for display in the “Landwehr Zeughaus”.  



The seals were certainly not attached after 1869, as by that time the “Königlich Bayerische 



Landwehr” was disbanded by the Bavarian King. The Zeughaus fr om 1870 on was 



maintained by the BNM. 416 One of the aforesaid 19 marked items is still in the BNM 



[ref_arm_1798]417. Some of the items of the Munich Zeughaus in the 1920ies or -30ies were 



given on loan to the BAM in Ingolstadt. Within time , for several objects their provenance 



was forgotten, access numbers got lost by extensive cleaning with an acetous liquid. From 



2012 on several items in the BAM were brought back to the Stadtmuseum.418  



The Italian armourers apparently not only produced armour of a common style, but they also 



marked the pieces with marks of the same type. This was often one or two letters underneath 



a crown, a cross with a split lower end or an abbreviation line. Armour bearing such marks 



is frequently considered to be of Italian origin. It has never been discussed that armourers of 



other, not Italian production regions might have taken advantage of the good reputation of 



Italian armour by adding similar marks to their items. While such deception s are known to 



have been frequently undertaken by producers of blades 419, this question has never been 



asked when marks on armour pieces had been discussed. Also in modern times, reproduced 



armourer’s or city marks might have been stamped into genuine plate to raise its value. 



Obviously marks resembling original models have been reproduced and stamped into the



plate of reproductions. The suit [ ref_arm_4128] is certainly not genuine, but the belonging 



type-VII helmet – made in the German style – bears a mark of Italian type.  



It seems as if some reproducers marked their objects to define them as copies. If 



Schedelmann is right with his assumption that the suit [ ref_arm_4141] is made by Leopold 



Winkelmayer420, the mark found under the nape -cutout of the suit’s backplate 



[ref_arm_3349] must be that of this 19th century Vienna armourer. This is very likely as the 



mark a ppears like a stylized “W”. By his mark maybe also some further works can be 



attributed to Winkelmayer’s workshop: the helmets [ref_arm_1899], [ref_arm_1857] and the 



chin/throat protection [ ref_arm_3202]. As the single unmarked chin/throat protection 



[ref_arm_3194] in shape and size is very similar to the aforesaid and to the one belonging to 



the Altena suit [ref_arm_3172], it is very likely that all three were made by Winkelmayer.
S. 209–211 · Sprachlich überarbeitet · Entwurf

8.4 Reconstructing original appearances

Reuniting dispersed components of former suits is difficult. The reconstruction of Lorenz Helmschmied ensembles from Ambras, now in Vienna’s HJRK, is a prominent example. A sketchbook attributed to him, showing garnitures with interchangeable components for different uses, helped identify parts.421422

Without contemporary images, ridges, etching, applied decoration and construction can suggest associations. Yet modern expectations of perfect matching can mislead. The breastplate and backplate of [ref_arm_4090] PDF do not align precisely, leading Ortwin Gamber to assign them to different suits.423

Thomas and Gamber proposed that around 1490 the lower pelvis edge of breastplate [ref_arm_3611] PDF had been flattened and its copper-alloy bands removed to attach upper-leg plates [ref_arm_5143] PDF [ref_arm_5144] PDF. These plates were detached in the 1970s to recover the supposed original appearance.424 Missing rivets suggest direct attachment to the lowest pelvis lame at the sides and internal leather connections towards the centre. Differing rivets and empty holes indicate several alterations, possibly including nineteenth-century restoration.

However, the small holes needed to attach the proposed decorative bands are absent. I could not examine the interior, but no former embossing is visible outside either. Pairs of holes survive at either side of the lowest lame, towards both centre and rear. A Type a rivet head appears beside a yellow-headed rivet on the upper-leg plate. These may have secured internal leather straps, leaving the yellow-headed rivets decorative. Alternatively, yellow-headed rivets near the upper central edge and lateral joint rivets may have held external straps to which the plates were buckled. Whatever their purpose, the holes were functional. The upper-leg plates may have belonged to the breastplate from the outset.

Contemporary images confirm that components did not always match perfectly. On late fifteenth-century sculpture [ref_ill_art_5160] PDF, breastplate and backplate contours fail to meet beneath the arms. Sculpture [ref_ill_art_5367] PDF shows a similar mismatch, with a plain front pelvis edge, perhaps accommodating upper-leg plates, and a ridged rear edge. Around 1480, [ref_ill_art_5207] PDF depicts a thoracic plate extending farther backwards below the arms than its abdominal plate.

Urgent need could favour available equipment over waiting for a tailored commission. Armour might be acquired from different makers or at different times and used together. Neither perfect stylistic agreement nor made-to-measure production should therefore be presumed.

Replacement components may be identified by comparing inner and outer surfaces. Patina, corrosion and wear can differ between older and newer pieces. Objects with many plates offer more comparisons; paired limb, hand and foot defences provide particularly useful evidence. Three SKD Type IV hand-defence pairs—[ref_arm_1238] PDF [ref_arm_1201] PDF, [ref_arm_1199] PDF [ref_arm_1236] PDF, and [ref_arm_1202] PDF [ref_arm_1239] PDF—appear each to have an entirely reproduced right-hand object, judging by internal and external corrosion patterns.

Helmet [ref_arm_1365] PDF was probably converted from a “Birnhelm” of the final quarter of the sixteenth century. Its original brim was lost or removed and replaced with one imitating a fifteenth-century “Capacete”. The skull shapes are very similar, but the later brim extends lower at the ears and is more pointed front and rear. Numerous plain arsenal Birnhelme survive, making them relatively inexpensive candidates for profitable conversion into a rarer medieval form.

The skull in this case is probably genuine: it is heavy and shows typical delamination. The thinner, uniformly thick brim has no visible delamination, differs in corrosion and meets the skull at a sharp internal edge, probably a weld.

Such comparisons still demand caution. Contemporary workers differed, several might contribute to one object, and a workshop could use sheets from different batches with different hammer and scale traces. Thickness also varies intentionally: pelvis lames are generally thinner than upper torso plates. Repairs made during an object’s working life can produce surface differences, while unquestionably genuine interiors may appear remarkably fresh [ref_arm_1978] PDF.

Originalwortlaut vergleichen
8.4 Discussion of the possible genuine appearance of armour 



The mapping of items  dispersed to different locations that once belonged to one suit is a 



difficult task. Several scholars tried to locate the parts of certain suits of armour. The most 



prominent of such enterprises was probably the re-arrangement of the Lorenz Helmschmied 



suits formerly in the armoury of Schloss Ambras in Innsbruck and now in the HJRK in 



Vienna. Fortunately, a sketchbook attributed to Lorenz Helmschmied showing 421 many 



drafts of “Garnituren” of armour, suits with parts exchangeable for different combat use, 



helped to identify the single pieces. 422 



Whenever no contemporary illustration of the suit in question is preserved,  the ridge -



decoration, etchings and  applications, but also the constructional details , can serve for the 



attribution of single parts to one suit . But care has to be taken, as the modern eye tends to 



ascribe only perfectly matching parts to one genuine composition. The extant breast- and the 



backplate of the suit [ ref_arm_4090] do not match perfectl y, which led Ortwin Gamber to 



the suggestion that they belonged to different suits 423. For the breastplate [ ref_arm_3611], 



Thomas and Gamber were suggesting that about 1490 the lower edge of the pelvis -lames 



had been hammered flat secondarily and the copper alloy bands got detached for the 



attachment of torso-upper leg-protections [ref_arm_5143] [ref_arm_5144]. The torso-upper 



leg-protections were detached in the 1970ies to reveal the “original” appearance of the 



plate.424 At the sides they were probably riveted directly to the lowest pelvis -lame and 



towards the center by an interior leather strap, as the missing rivets at these locations suggest. 



The different rivets and “empty” holes suggest that different alterations were made, probably 



also in the times when the suit was restored in the 1800s. Nevertheless, the small holes 



necessary for riveting the decorative bands are missing and therefore Thomas’ and Gamber’s 



assumption becomes questionable. It was not possible to examine the lames interiorly, but 



from the outside also no traces of a former embossing is visible. At each side of the lowest 



lame, towards the cen tre and towards the back -lames, a pair of holes is visible. Next to a 



yellow-headed rivet at the torso-upper leg-protections, the head of a rivet of type-a is visible. 



These holes maybe once held the rivets for an interior leather strap that fixed the torso-upper 



leg-protections to the pelvis -lames, leaving the yellow -rivets at their upper edge for 



decorative purpose only. A second possibility is that the single yellow -head rivets at the 



central upper edge of the lowest pelvis -lame together with the joint -rivets at the side of the



pelvis once fixed exterior leather straps to which the torso -upper leg -protections were 



buckled. Whatever the purpose of the holes was, it is clear that they were not drilled without 



reason. In the case of the said torso -upper leg-protections, it is possible that they belonged 



to the breastplate from the beginning.  



All the aforesaid approaches are not unproblematic, as contemporary artworks show that the 



single parts did not always match perfectly. For example at the late 15 th century sculpture 



[ref_ill_art_5160] the lines of the back - and the breastplate do not properly meet under the 



arm cutouts. This miss-match is also found at the sculpture [ref_ill_art_5367] and here also 



the lower edge of the pelvis-lame at the backplate is designed different from the pelvis-lame 



of the breastplate. At the front-protection it is left plain – probably to allow a close fit of the 



torso-upper leg-protections – and at the backplate the lower edge is decorated and stiffened 



by a ridge. But also the single segments of one armour part did not always fit perfectly: on a 



sculpture of about 1480 an armoured man wears a breastplate with a thorax-plate under the 



arm cutouts extending much wider towards the back than the abdomen -plate 



[ref_ill_art_5207]. Also in the Middle Ages, time was a precious good and if there was an 



urgent need for a the wearing of armour, the noble fighters could not wait until a customized 



suit was finished. It should be considered that armour was not necessarily made to measure 



and could have been bought in different sales, from different makers to form one suit. 



To tell which segments of an extant suit are genuine and which are reproduced in most cases 



is only possible when items once got completed or broken parts got replaced. The 



examination of the in- and exterior plate surfaces might help to identify replaced parts. The 



patina or the corrosion in such cases often differs slightly from the genuine to the reproduced 



parts, the older ones are expected to look more worn out or aged. The more plate segments 



an armour piece compris es, the simpler the comparison of such details becomes. By the 



nature of the human body, usually the armour for the limbs, the hands and feet consists of 



more different segments than protections for the torso, for the head and for the neck. The 



first group is often extant in pairs and if both sides of the body are at hand, there is even a 



wider basis for comparisons. In the SKD there are three pairs of type -IV hand-protections 



[ref_arm_1238] [ ref_arm_1201]; [ ref_arm_1199] [ ref_arm_1236]; [ ref_arm_1202] [ 



ref_arm_1239]. The right hand -protection of each pair is most likely entirely reproduced. 



The in- and the exterior corrosion-pattern suggests this assumption.  



The helmet [ ref_arm_1365] is probably an altered so called “Birnhelm” of the last quarter 



of the 16th century. The brim was lost or got cut off and was replaced by a new one resembling 



a 15 th century helmet often called “Capacete”. The skulls of these two helmets are very 



similar – if not same – in shape. The difference is that the brim of the later type curves deeper 



at the ears and is more pointed at the front and the back than at the 15 th century type. A 



Birnhelm is av ailable comparatively cheap on the antique market, as hundreds or even 



thousands of objects survive, especially of the plain and undecorated arsenal -version. A lot 



of money can be made by the modification of such a helmet, turning it into a rare and thus 



expensive late medieval type. In the mentioned case the skull is most likely genuine. It shows 



the typical delaminations and is of rather heavy quality. The brim has a very sharp edge at 



the interior where it is probably welded to the skull. The plate of th e brim is thin, equal in 



thickness and showing no delamination. Also the appearance of the corrosion is different 



from the skull. 



Still care has to be taken with a too quick condemnation of single segments. Each armourer 



– the medieval and the modern – works a little different, and several contemporary workers 



might have finished one item. There were certainly different charges of plate used in the 



same workshop, with different marks left by different hammers and different remains of 



hammer scale etc. Also the plate-thickness differs purposely, for example the segments of



the pelvis protection of a torso front were usually made of thinner material than the upper 



parts. Another problem with the differentiation of the surfaces is that different corrosion 



traces could derive from the replacement or repairing of segments in times when the item 



was still in use. Finally the interior surface of certainly genuine examples can also look as it 



has just left the workshop [ref_arm_1978].
S. 211 · Sprachlich überarbeitet · Entwurf

8.5 Selected authenticity case studies

Close comparison of objects sharing many features can clarify questions of authenticity. The following cases examine possible relationships between originals and reproductions, and the evidence supporting or limiting particular assessments.

Originalwortlaut vergleichen
8.5 Authenticity discussion of single chosen objects 



For a detailed discussion of the problem of authenticity the finding and subsequent 



comparison of objects that share a great deal of common features can be of immense help. 



In the following the presumable influence of some original items on reproductions will be 



discussed.
S. 211–212 · Sprachlich überarbeitet · Entwurf

8.5.1 The “Sigmaringen” armour in Detroit

The Detroit Institute of Arts suit [ref_arm_3214] PDF425 shares features with numerous objects elsewhere. It passed from the Hohenzollern armoury at Sigmaringen through a New York dealer to William Randolph Hearst, and then to the DIA.426 Its present display combines original and reproduced components.

The breastplate, backplate, shoulders, knees and upper-leg defences are regarded here as genuine. Their accomplished workmanship and, except on the shoulders, Lorenz Helmschmied’s marks support this judgement. Comparison with his attributed Vienna work establishes a close relationship. The upper-leg flaps and front pelvis lames are later additions, distinguishable by their cruder detail.427

The hand, forearm, elbow, upper-arm, lower-leg and foot defences, together with the helmet and neck defence, are reproductions. Stuart Pyhrr attributes them to an anonymous Munich workshop around 1870.428 Since other makers also completed suits without marking their work, Vienna, Paris or another centre cannot be excluded. Completion predates 1904: Gimbel’s catalogue published that year includes a copy with the same additions [ref_arm_4131] PDF.429 Although it differs slightly from the present Detroit arrangement, especially in its crudely made legs, it clearly follows the DIA suit.

Other copies survive. A full-size likeness stands in a wall niche beside the entrance steps at Sigmaringen [ref_ill_art_5350] PDF; dating it might refine the chronology of the original’s additions. Meersburg holds full-size iron casts of the left thigh and knee and the left upper and lower arm [ref_ill_art_5251] PDF. In 1964 Galerie Fischer sold a smaller iron cast whose legs served as a chimney flue [ref_ill_art_5376] PDF, catalogued as mid-nineteenth-century.430

An SKD breastplate and backplate closely resemble the Detroit originals [ref_arm_3629] PDF [ref_arm_3321] PDF. The associated suit may be entirely reproduced. Its neck defence [ref_arm_3175] PDF lacks necessary lining holes and, unusually for such elaborate work, an articulated upper lame. It is also the lightest recorded example of its type. Another neck defence [ref_arm_3054] PDF likewise lacks lining holes. Surprisingly, all components of the Dresden suit, including helmet [ref_arm_1725] PDF, bear a Nuremberg mark, rare on surviving pre-1500 armour.

Numerous other backplates—[ref_arm_3280] PDF [ref_arm_3289] PDF [ref_arm_3314] PDF [ref_arm_3400] PDF [ref_arm_3402] PDF [ref_arm_4779] PDF—and breastplates—[ref_arm_3582] PDF [ref_arm_3583] PDF [ref_arm_3594] PDF [ref_arm_3603] PDF [ref_arm_3629] PDF [ref_arm_3729] PDF [ref_arm_3805] PDF [ref_arm_3289] PDF [ref_arm_3971] PDF [ref_arm_4006] PDF [ref_arm_4015] PDF [ref_arm_4052] PDF—probably reproduce the Detroit plates [ref_arm_3401] PDF [ref_arm_3757] PDF or closely related Vienna originals [ref_arm_3299] PDF [ref_arm_3300] PDF [ref_arm_3301] PDF [ref_arm_3611] PDF [ref_arm_3613] PDF [ref_arm_3614] PDF [ref_arm_3615] PDF. Schmidt’s catalogue apparently offered a copy of the whole Detroit suit [ref_arm_4082] PDF.

Redaktionelle Hinweise · 2
  • ref_arm_3289 steht im Original sowohl unter Rücken- als auch Brustplatten; doppelte Zuordnung unverändert erhalten, fachlich prüfen.
  • Die ursprünglichen Echtheits- und Werkstatturteile bleiben als Bewertungen dieser Untersuchung erkennbar, nicht als neue externe Bestätigungen.
Originalwortlaut vergleichen
8.5.1 The “Sigmaringen” armour in Detroit 



Many features of a genuine suit of armour in the Detroit Institute of Arts [ref_arm_3214]425 



are found similarly on numerous comparable examples in other collections. The DIA armour 



suit has been sold from the Hohenzollern armoury at Schloss Sigmaringen via a New York 



art dealer to the collector William Randolph Hearst, from whose collectio n it went to the 



property of the Detroit Institute of Arts.426 As it is displayed at the moment it is a composition 



of reproduced and genuine parts. The genuine parts are the breast - and the backplate, the 



shoulders, the knees and the upper legs. The certain ty about the authenticity of these parts 



derives from the observation of the obviously skillful mastership by which they were created 



and the marks of Lorenz Helmschmied found at all the aforesaid plates with the exception 



of the shoulders. A comparison to the objects kept in the court armoury at Vienna attributed 



to the same master make the relationship undoubted. The flaps at the upper legs and the 



pelvis-lames of the breastplate are completions, as all details are made more crudely.427  



The hand-protections, the lower arms, the elbows, the upper arms, the lower legs and the 



feet as well as the helmet and the neck -protection are reproductions. Stuart Pyhrr ascribes 



these reproduced parts to the workshop of an anonymous armourer of Munich aroun d
S. 212 · Sprachlich überarbeitet · Entwurf

8.5.2 Several neck defences

Some of these reproductions may come from a Munich workshop, judging by their similarity to neck defences illustrated in Ernst Schmidt’s catalogue [ref_arm_4089] PDF. Schmidt examples generally use a projecting metal tongue inserted through a staple on the breastplate. No certainly genuine armour or contemporary depiction identified here uses this connection, suggesting a late nineteenth- or early twentieth-century invention.

Their lower neck plate is also commonly embossed to accommodate the breastplate’s turned edge beneath it, another feature not observed on genuine examples. Neck defences [ref_arm_3039] PDF [ref_arm_3031] PDF [ref_arm_3054] PDF may therefore be products of the same atelier.

Originalwortlaut vergleichen
8.5.2 Various neck-protections 



Many of the aforesaid reproduced parts might have been made in a Munich workshop, as the 



formal similarity of the neck -protections with items shown in the catalogue of the Atelier 



Ernst Schmidt suggests [ref_arm_4089]. The Schmidt neck-protections are usually attached 



by a plate -tongue, stuck through a staple riveted to the breast plate. This type of joint can 



neither be found at any certainly genuine armour nor at any contemporary artwork. It is 



therefore most likely an  invention of a copyist of the late 19 th or early 20 th century. At the 



Schmidt pieces, the lower plate of the neck is usually embossed where the turned edge of 



the breastplate underneath is located. This feature is also not found at genuine neck-defenses. 



Therefore, also the neck-protections [ref_arm_3039] [ref_arm_3031] [ref_arm_3054] might 



be reproductions of his Atelier.
S. 212–213 · Sprachlich überarbeitet · Entwurf

8.5.3 A suit in the BMA

The BMA suit [ref_arm_4141] PDF closely resembles Lorenz Helmschmied’s Vienna work and the Detroit suit. Laking illustrated it as a Bavarian reproduction,431 acknowledging its deceptive quality but offering only brief, largely impressionistic reasons:

It is rather difficult to point to any actual defect in its general form; but 



we can distinguish a certain over-modelling of the fronts of the jambs, 



and we may also suggest that its pointed sollerets are purely imaginative 



in form. Again, if we examine the surface of the metal, we shall find that 



it is leaden and lustreless, of a colour that no amount of cleaning would 



bring to that splendid black glossy appearance of true XVth century 



plate.
Laking (1920), p. 119. 432

In 1964, Schedelmann attributed it to Leopold Winkelmayer in Vienna without giving a reference.433 The Altena museum purchased it from Munich dealer Xaver Scheidwimmer in November 1955 for DM 4,000. Its register describes a nineteenth-century Viennese reproduction from the Kuppelmayer collection, modelled on Vienna suit [ref_arm_3258] PDF.434

None of these accounts mentions the stylised W beneath the nape opening of backplate [ref_arm_3349] PDF. Unlike known medieval marks, it could identify Winkelmayer and suggest that the work was originally sold openly as a reproduction.

The suit illustrates how difficult it is to articulate an intuitive authenticity judgement. Its workmanship is excellent. The breastplate delaminates, and the rivets have copper-alloy caps folded around their heads like genuine examples. More unusual are the narrow pelvis lames relative to the torso and the nearly symmetrical upper edges of the thigh defences. The absence of sliding rivets makes the hands and upper legs stiff. Buckles and gilded copper-alloy fittings are so carefully made that they are difficult to distinguish from presumed originals.

Crucially, helmet [ref_arm_1702] PDF is genuine: a rare late fifteenth-century Type VII variant.435 The maker of the reproduced components added copper-alloy bands to match it. Earlier assessments of the suit overlooked this distinction. Its lower-leg defences are probably also genuine, though sixteenth-century.

Originalwortlaut vergleichen
8.5.3 A suit in the BMA 



In the BMA there is a suit of armour [ ref_arm_4141] that closely resembles the works of 



Lorenz Helmschmied in Vienna and the DIA suit. Laking in his chapter on forgeries included 



an image of the suit, saying that it is a Bavarian reproduction 431. He admits that this is a 



quality of reproduction that is very deceptive. The arguments that brought him to this 



conclusion are superficial and short:



It is rather difficult to point to any actual defect in its general form; but 



we can distinguish a certain over-modelling of the fronts of the jambs, 



and we may also suggest that its pointed sollerets are purely imaginative 



in form. Again, if we examine the surface of the metal, we shall find that 



it is leaden and lustreless, of a colour that no amount of cleaning would 



bring to that splendid black glossy appearance of true XVth century 



plate.432  



In his 1964 article on reproductions, Hans Schedelmann – without including a reference – 



attributes this suit to the workshop of Leopold Winkelmayer in Vienna.433 



In November 1955 this suit was bought by the Museum in Altena from the Munich art-dealer 



Xaver Scheidwimmer for the price of 4000, - DM. It was described as coming from the 



Kuppelmayer-collection in Munich, being a 19 th century reproduction made in Vienna and 



modeled after the suit [ref_arm_3258] in the HJRK in Vienna.434  



None of these descriptions mentions the mark, showing what could be a stylized “W”, under 



the nape-cutout of the backplate [ref_arm_3349]. It has no similarity with any other mark of 



the late Middle Ages and could well stand for the name “Winkelmayer”. This mark indicates 



that the suit was not necessarily made to deceive a potential buyer and was fir st sold as a 



reproduction. 



Leaving aside that the mark might tell about its maker, this suit is a very good example for 



demonstrating how difficult it can be to find words for what the specialist “feels” when 



testing authenticity. The craftsmanship is very good, the metal of the breastplate shows 



delaminations and the rivets have caps of copper alloy embraced to their heads, just as many 



genuine rivets at other items have. The only things that remain strange are the – in proportion 



to the upper plates at the front and the back – uncommon narrow pelvis-lames and the almost 



symmetric upper end of the upper-leg-protections. Furthermore, the absence of sliding rivets 



at the hands and the upper legs leaves these parts very stiff. All parts are generally made with 



the greatest care and are of wonderful craftsmanship, the buckles and the gilded copper alloy 



applications cannot easily be distinguished from ot her, probably genuin e examples. 



Interestingly, the helmet [ref_arm_1702] of this suit is certainly no reproduction, but a very 



rare example of a late 15th century variation of type-VII helmets.435 The maker of the rest of 



the suit intended to match the helmet by adding the copper alloy bands. Too busy with the 



testing of the suit’s authenticity, the former scholars missed this important detail. Probably 



also the lower leg-protections are genuine examples of the 16th century.
S. 213–214 · Sprachlich überarbeitet · Entwurf

8.5.4 A Type VIII helmet in the Royal Armouries

Karen Watts investigated the attribution of Royal Armouries objects to Thomas Grimshaw, beginning with two helmets purchased in 1851 from his alleged associate Samuel Pratt. One case illustrates the difficulties of the argument.436

Watts considered the Type VIII “great basinet” [ref_arm_1657] PDF unusually heavy, comparing it with the mid-fourteenth-century Type II [ref_arm_1443] PDF. That is not a like-for-like comparison. Closer parallels are Type VIII helmets converted from earlier Type IV skulls by adding shoulder plates in the first half of the fifteenth century:437 [ref_arm_1653] PDF [ref_arm_1655] PDF [ref_arm_1768] PDF.438

Those skulls have a point projecting slightly backwards and an almost vertical rear profile. The suspected Grimshaw helmet instead has an egg-shaped crown with a slight medial ridge. The only comparable example known to me appears in a nineteenth-century drawing [ref_arm_4219] PDF; its present location and authenticity are unknown. The unusual skull makes assembly from a familiar genuine earlier helmet unlikely, but lost or unidentified parallels remain possible.

Watts also regarded unfinished rather than wire-turned edges as suspicious. Yet no pre-mid-fifteenth-century great basinet known to me has turned edges, so this feature is compatible with historic practice. Her objection to a forehead spring catch—that a wearer could not readily reach around the pointed visor to release it—is likewise unconvincing. Numerous medieval helmets have visor catches, commonly at the right cheek [ref_arm_1704] PDF, only about 15 cm from the position in question. The catch’s unique design is nevertheless suspicious.

Stronger objections are the poor visibility through the closed visor and reported rolling marks inside. Taken together with the Pratt provenance, these features make reproduction very likely. Even so, the object is evidence for armour-making history. Watts’s report that it “has rusted now completely” is regrettable: neglect and inaccessibility diminish the comparative evidence needed to understand reproductions.

Redaktionelle Hinweise · 1
  • Unumgelegte Ränder sind hier mit mittelalterlicher Praxis vereinbar, aber kein eigenständiger Echtheitsbeweis. Die stärkere Originalformulierung ist entsprechend präzisiert.
Originalwortlaut vergleichen
8.5.4 A type-VIII helmet in the Royal Armouries 



Karen Watts tried to find proof for the prevalent mapping of certain items in the Royal 



Armouries to the workshop of the  London forger Thomas Grimshaw. Her considerations 



start with the  examination of two helmets bought by the Tower Armouries in 1851 from 



Samuel Pratt – an art dealer said to have been Grimshaw’s accessory. Not all of the further



mentioned helmets can be revised here, so only one will be chosen to make clear how 



problematic some preceding approaches to the authenticity question had been.436 



The helmet [ref_arm_1657], a type-VIII “great basinet”, is too heavy in comparison to any 



other helmet of the same type, she argues. As a comparative piece, she quotes the weight of 



the helmet [ref_arm_1443], which is of type-II (mid 14th c.) and not of a 15 th century type-



VIII – and therefore actually not comparable. Comparable 437 are merely “great basinets”, 



made from older type -IV helmets, to which lower shoulder -plates were riveted in the first 



half of the 15 th century ([ref_arm_1653] [ref_arm_1655] [ref_arm_1768]438). The skulls of 



these helmets all have a point, projecting slightly backwards and leaving the rear profile in 



an almost straight vertical line. The “Grimshaw skull” is pointless with a slight medial ridge 



at the egg-shaped apex. The only similar skull the author knows from a 19th century drawing 



only, its present location is not known and therefore its authenticity cannot be tested 



[ref_arm_4219]. As this skull -shape is so unique, it is unlikely that the Tower item is a 



composition of a genuine skull and secondarily attached lower plates. Nevertheless, it is 



possible that further helmets similar to this example existed, but all of the m are lost or not 



known.  



Watt’s argument that the helmet must be a reproduction as the main edges of this helmet 



were not turned over wire but instead left unfinished is rather a proof of authenticity. As far 



as the author knows, no “great basinet” from before the mid-15th century has any edge turned. 



Also her arguments that try to support the impossibility of the spring-lock at the forehead of 



the skull, holding down the visor, are not compre hensible as well. The statement that the  



“spring-catch on this v isor is designed to hold the visor down. In effect, the wearer is 



trapped, as it is very difficult to get an arm round the pointed visor to release it”  presumes 



that late medieval fighters were immobile. There are hundreds of late medieval helmets, of 



different types, that have a spring catch holding down the visor (e. g. [ref_arm_1704]). This 



could usually be released on the right cheek, just some 15 cm away from the position of the 



catch at the “Grimshaw h elmet”. Each spot of a medieval helmet can easily be reached by 



its wearer’s hand, now and then. It is nevertheless suspicious that the lock of the “Grimshaw 



helmet” is not found at any other medieval helmet. The reasonable of Watts’ arguments for 



the helmet being a reproduction are the impracticality of the helmet, as the wearer could 



hardly see through the sight when the visor is closed and the interior marks from the plate -



rolling. 



The sum of suspicious features and the Pratt-provenance makes it very likely that this helmet 



is a reproduction. Nevertheless, it is a part of the history of armou r-making and therefore it 



is sa d to read that the item “has rusted now completely”  in the storage of the Royal 



Armouries. With each unattended and not accessible “for gery” the chance is shrinking to 



find better arguments for the mapping of armour as reproductions of originals.
S. 214–216 · Sprachlich überarbeitet · Entwurf

8.5.5 A Type II helmet in the Royal Armouries

Watts argues that Royal Armouries helmet [ref_arm_1468] PDF is genuine. It appeared at Sotheby’s in 1974 without documented provenance, was described as a Pratt/Grimshaw forgery, but was ultimately acquired as an original. Correctly positioned lining rivets and other details, she suggests, exceed what Grimshaw would have attempted: his work generally followed images rather than close examination of originals. She concludes:

“In fact, it is not a fake at all, but is generally accepted as a genuine 



helm of the fourteenth century.”
Watts (1992), p. 104. 439

Neither unspecified consensus nor exclusion of one possible maker proves authenticity. The only other published assertion identified here is Derek Spalding’s earlier article, which Watts does not cite.440

The helmet closely resembles [ref_arm_1461] PDF in the National Museum of Scotland. The principal difference is the absence of left-cheek ventilation holes on the Leeds example. The Edinburgh helmet is very thin: minimum 0.6 mm, maximum 1.9 mm; front left 0.6 mm, front right 1.8 mm, left cheek 1.7 mm and right cheek 1.4 mm.441 Distorted and broken cross-shaped openings, and a hole exposing wire in the lower turn, make the thinness evident. Since the helmets differ in weight by only 0.11 kg, or four ounces,442 their thicknesses may be broadly comparable. Such thin material makes use in combat or tournament doubtful.

Each consists of three plates: a conical tube above ear level, a slightly embossed crown plate closing it, and a lower tube protecting cheeks, ears and nape. No seam is visible in either tube, implying forge-welded closure. The reason for this elaborate construction is unclear; no other known helmets use it. A maker already capable of welding the tubes could have used one taller tube and a crown plate instead.

Comparisons commonly have a one-piece upper skull with separate lower plates [ref_arm_1465] PDF [ref_arm_1466] PDF [ref_arm_1471] PDF [ref_arm_1481] PDF [ref_arm_1490] PDF, while others have multi-piece skulls [ref_arm_1457] PDF [ref_arm_1484] PDF [ref_arm_1486] PDF [ref_arm_1488] PDF.

Williams examined one flake from the interior of each helmet, without recording its dimensions.443444 All his conclusions derive from these samples. He reports 430 VPH in a 0.3 mm outer layer of [ref_arm_1461] PDF, and an average of 290 VPH for [ref_arm_1468] PDF.445 He interprets the former as soft iron with a case-carburised surface. The account does not clearly explain how the harder outer layer was established; distinguishing hardness through the thickness requires measurements across an appropriate section.

Two possible manufacturing sequences deserve consideration. First, the completed helmet could have been carburised and hardened after assembly, either using plates carburised beforehand or enclosing the assembled object in carbon-rich packing. Subsequent oxide scale would be difficult to remove around rivets and overlaps if a bright finish were required.

Second, the plates could have been hardened before assembly. Distortion during heating, handling or quenching could then impair fit, perhaps requiring a supporting structure for each plate.

The sampled flakes came from the interior, which often preserves evidence removed from the exterior by grinding. Deliberate case hardening for protection would be expected to affect the outside too. The sequence of carburising and grinding is therefore critical: grinding after carburising can remove part of the enriched layer. Exterior testing and comparison of layer thicknesses could help resolve that sequence.

A very thin harder layer confined to the interior might instead result from incidental carburisation. In sheet-making, clay and charcoal mixtures could prevent stacked plates from welding.446 Under suitable conditions, heating such packs might introduce carbon into their surfaces.

Given these helmets’ accomplished workmanship, the extra cost of steel stock would probably have been modest relative to deliberate carburising. Their component sheets are small compared with those needed for one-piece helmets, and the necessary techniques were available. If genuinely fourteenth-century, both would have been made from mechanically refined material. Their close relationship offers an unusual opportunity for comparison; Spalding suggested a common workshop.447 Further examination of both is warranted.

Redaktionelle Hinweise · 3
  • Das Original nennt Spaldings Aufsatz „15 years before“, obwohl die zitierten Jahre 1981 und 1992 elf Jahre ergeben. Die widersprüchliche Abstandszahl wurde nicht übernommen.
  • Die Originalaussage zur Reihenfolge von Aufkohlen und Schleifen widerspricht ihrer Begründung. Keine Reihenfolge als bewiesen festgelegt; die prüfbare Fragestellung bleibt erhalten.
  • Aus ähnlichem Gewicht folgt nicht zwingend gleiche lokale Plattendicke. Die ursprüngliche Vermutung bleibt ausdrücklich bedingt.
Originalwortlaut vergleichen
8.5.5 A type-II helmet in the Royal Armouries 



Karen Watts in her article on armour made by the forger Thomas Grimshaw argues why she 



considers the type-II helmet [ref_arm_1468] of the Royal Armouries as genuine. This helmet 



appeared without any documentation of its provenance in 1974 in a Sotheby’s auction,



denounced to be one of the Pratt/Grimshaw fa kes, but was eventually considered and 



acquired as genuine by the Royal Armouries. Watts describes some details that argue for the 



authenticity of this helmet, like the correct placement of the rivets for the lining etc. In her 



opinion, Grimshaw would not have bothered with such details. An accurate reproduction 



would have made the study of originals necessary, but Grimshaw seems to have worked from 



depictions only. Watts draws the following conclusion:  



“In fact, it is not a fake at all, but is generally accepted as a genuine 



helm of the fourteenth century.”439  



The obscure “general acceptance” and the assumption that it could not have been made by 



Grimshaw as it is of alleged too good quality, are used as a proof of authenticity. The 



“general acceptance”  cannot be retraced in any document. Only one article repeats her 



claim that the helmet is genuine. This was written 15 years before Watts’ by Derek Spalding 



but was not quoted by Watts.440  



The concerned helmet is almost identical to another example in the Nati onal Museum of 



Scotland [ref_arm_1461]. The only major difference is that the Leeds head piece, unlike the 



Edinburgh one, has no breathing holes at the left cheek. The helmet in Edinburgh is made of 



very thin plate (min. 0.6; max. 1.9 mm; skull front left 0.6 mm; skull front right 1.8 mm; 



cheek left 1.7 mm; cheek right 1.4 mm) 441. How thin the plate at the front indeed is, can 



easily be seen at the deformed and broken out cross-shaped holes and at the hole tha t 



uncovers the wire inside the inwards rolled lower edge. As the weight of both helmets differs 



only by 0.11 kg or 4 ounces442, the plate-thickness of both pieces might be more or less the 



same. Due to the thin material, such helmets are very unlikely to have been used in battle or 



tournament. 



The Edinburgh and the Leeds helmets are both made of three plates only: a cone -shaped 



“tube” covering the skull from above the line of the ears upwards, closed at the crest by a 



slightly embossed plate and a second tube, protecting cheeks, ears and nape. The tubes show 



no seam, therefore they must have been produced via the forge welding of a roll . It is not 



clear why the armourer put so much effort in this construction. No other helmets are 



constructed this way. As the armourer already forge-welded the plates, he could have made 



the helmet already from one single tube only with an inserted comb-plate. Many comparable 



helmets have the ir skull made of one piece from above the ears with several lower plates 



attached, protecting the face and the nape [ ref_arm_1465] [ref_arm_1466] [ref_arm_1471] 



[ref_arm_1481] [ ref_arm_1490]. Other examples also have the skull made of several 



segments [ref_arm_1457] [ref_arm_1484] [ref_arm_1486] [ref_arm_1488]. 



In his article “Four helms of the fourteenth century compared”443 Alan Williams says that he 



took a single flake from the interior of each of the two discussed helmets for his 



metallographic examination444, the dimensions of the sample are not given. All testing results 



concerning these two items derive from these particles. He quotes the hardness of the helmet



[ref_arm_1461] at 430 VPH at an outer layer of 0.3 mm thickness and the average hardness 



of the helmet [ ref_arm_1468] at 290 VPH.445 For the helmet [ ref_arm_1461] he suggests 



that the material was soft iron that got case-carburized as it was only harder at an outer layer. 



Williams does not explain how he found out that the hardness of the helmet [ref_arm_1461] 



was higher at an outer layer. The conventional hardness testing method can only distinguish 



between harder and softer layers if several sections of the material are tested. 



The author of this study will try to reconstruct the processes necessary to case-carburize and 



to harden such a helmet: 



The first possibility for the manufacture would be that this helmet had been case-carburized 



and hardened after the mounting of all the ready-shaped and ground pieces. The plates either 



got carburized before they were mounted, or the mounted helmet was packed into a carbon 



rich coat and heated for a long time. After the hardening, the surface must have been dark 



from oxidation products. This would be very difficult to be cleaned off around the rivets and 



the overlapping edges, if the helmet should appear “white”. 



A second possibility would be that the plates got hardened before mounting. This is very 



problematic, as they easily get deformed by handling or quenching, which can cause fitting 



problems when the parts are being mounted. A supportive construction would be necessary 



for each single piece to avoid deformation throughout the hardening process. 



The sample-flakes for the metallurgical analysis were detached from the interior. The interior 



of armour is a mirror of what the outer surface had looked like before grinding. Case 



carburizing would only make sense if also the exterior surface or the armour-piece would be 



of increased hardness. The case  carburization was most likely applied before the grinding, 



as otherwise too much of the carburized “steel” layer would get lost. A hardness test at the 



exterior surface of the helmet could help to determine if the plates were case -carburized 



before grinding – the hard layers would have to show nearly the same thickness. 



The most likely explanation of a very thin harder layer, presumably only found at the inside, 



is a randomly obtained case carburization. As described in the chapter on plate production446, 



the single plates worked in one pack were possibly prevented from welding together by some 



clay liquid mixed with charcoal dust. The heating of these packs for forging could, under the 



right conditions, result in the diffusion of carbon into the iron.  



The discussed helmets are of such masterly craftsmanship that  the higher price for the use 



of steel would not matter  compared to the costs for carburizing the iron plates. It was also 



not a problem to produce plates of the required formats from steel. The plate s of the 



discussed helmets are rather small, compared to those of helmets driven from one single 



plate. All the necessary techniques and tools were available. 



If the two helmets were made in the 14th century, they were certainly made of wrought-iron. 



They offer a very unique chance to learn more about the 14 th century armour making, as no 



other pieces of armour are so closely related to each other – they might even come from the 



same workshop, as suggested by Spalding 447. Future testing might compare these tw o 



helmets in more details.
S. 217 · Sprachlich überarbeitet · Entwurf

8.5.6 An electroformed helmet in Delft

Some objects can be identified securely as reproductions when their manufacturing process is demonstrably later. Electroforming provides one example.448 In 2003 Jan-Piet Puype identified the “golden helmet of Delft”, made in early seventeenth-century style, as such a product. His observations are explicit and persuasive.449

In 1999, the Legermuseum learned of a nearly identical helmet in the Hermitage, St Petersburg. Comparison revealed close agreement in shape and decoration but significant constructional differences. The Hermitage edges were rolled; Delft’s were solid. Delft’s plume holder and rivets appeared integral with the skull rather than separate fittings.

The Delft helmet was consequently suspected to be a modern copy. Its thin walls made conventional casting unlikely, although a fracture resembled cast metal. Analysis of a detached sample indicated neither casting nor forging and pointed strongly to electroforming. This would probably have required a mould taken from the St Petersburg original, documented in that collection by 1869, although no record of mould-making survives. Puype suggested a study or other non-deceptive purpose.

A further circumstantial connection may support this interpretation. In St Petersburg during the late 1860s and 1870s, the chemist Klein refined iron electroforming. No armour copies are documented, but he made an iron shield embossed with an Amazon battle.450 The proximity of his workshop to the imperial collections makes him or his workshop a possible source of the Delft copy, though this remains unproven.

Originalwortlaut vergleichen
8.5.6 An electro-plated helmet in Delft 



In a few cases, objects can be definitely identified as reproductions, for example when an 



item was made by the technique of electro plating 448. Jan-Piet Puype in 2003 identified an 



early 17th century helmet, the so called “golden helmet of Delft”, as a product of this method. 



The detail -observations that led to this conclusion are absolutely reasonable and 



comprehensible.449  



In 1999 the “Legermuseum” in Delft got a hint, that there is a helmet almost identical to the 



Delft example kept in the Eremitage in St. Petersburg. Both objects were compared closely 



and many parallels were confirmed. The decoration and shape of the object resembled very 



closely the St. Petersburg example, but some technical details differed. While the plate edges 



of the Eremitage helmet were rolled, they were found to be massive at the Delft head piece. 



The plume holder and the rivets at the Delft helmet seemed to be worked in one piece with 



the plate of the skull. After th e recognition of these and other eye catching differences, the 



Delft example was suspected to be a modern copy of the Eremitage helmet. It was found to 



be unlikely that the Delft helmet was cast, as the plate was too thin to be made by this 



technique. Nevertheless, at a crack the material showed a similar appearance to cast iron. 



Puype thus ordered a metallurgical analysis of a detached sample of the item. The helmet 



was found to be neither cast nor forged. The results of the metallurgical examination left 



only one possible answer: The helmet was most likely made by electro plating, which 



probably required a mold made from the original item in St. Petersburg. The latter is 



documented as part of the collections as early as 1869. However, the documents of the 



museum do not mention that a mold ever has been made from the original. Puype suggested 



that the helmet has maybe not been made to deceive but rather for study or any other purpose.  



The author found one more argument that supports Puype’s suggestion for t he item being 



made by electro plati ng. It might be a coincidence: Also i n St. Petersburg – where the 



presumable model for the Delft helmet is kept – by the late 60ies and 70ies of the 19th century 



a chemist named Klein brought the electro-plating of iron artifacts to perfection. While it is 



not recorded that he made copies of armour, it is documented that he had made an iron shield 



showing an embossed scene of an amazons -battle.450 Due to these facts and to the close 



vicinity of Klein’s laboratory to the artifacts in the Tsar’s collections, it is possible that it was 



him or his workshop that made the copy of the Petersburg helmet.
S. 217–219 · Sprachlich überarbeitet · Entwurf

8.5.7 A Type VII helmet sold in 2011

Where Boeheim sought rolling grooves beneath artificially applied hammer marks, later writers have attributed similar marks to a particular reproduction maker. The 2011 Klingbeil sale catalogue described lot 182 as follows:

[…] The interior shows unusual hammerwork, the result of using a 



hammer with a very small head. This style of workmanship is 



characteristic of Raymond Bartel, the armourer to William Randolph 



Hearst. A sallet of similar construction also showing characteristic small 



hammer marks was made by Bartel and included as an addition to the 



sale of the armoury of the Dukes von Ratibor , Galerie Fischer 



Waffensaal des Schlosses Grafenegg, II. Teil, May 2, 1934, lot 67.
Pierre Bergé & associés (2011), lot 182. 451

The wording avoids a categorical authenticity judgement but strongly suggests modern manufacture. Yet the 1934 Fischer entry for the cited comparison [ref_arm_5129] PDF offered it as genuine and did not attribute it to Bartel.452 The later attribution’s source is unclear.

I therefore sought independent support for small hammer marks as a Bartel characteristic. His known left-hand defence [ref_arm_1147] PDF, made for Glasgow suit [ref_arm_4117] PDF after its acquisition by Hearst, copies the surviving right-hand object. Inside the cuff it bears a tournament helmet above “R. B.”. No delamination is visible, suggesting material other than wrought iron, but its interior has no unusual hammer marks. Hand defences may require different working from helmets; I could not examine a securely identified Bartel helmet before completing this study.

Karsten Klingbeil allowed me to examine the disputed Type VII helmet in February 2011. Photographs record its interior marks [ref_arm_4242] PDF.453 Their diagnostic value can be tested against other examples.

An uninventoried DHM helmet [ref_arm_1713] PDF has strikingly similar small marks. Its provenance requires further research. Copper-coloured brazing appears inside; the brown, rough exterior may result from acidic cleaning or artificial patination. Several areas delaminate, consistent with mechanically refined iron, while its form matches known examples without obvious signs of unskilled work. No independent evidence establishes it as a reproduction.

Two HJRK Type VII helmets, accepted as genuine on collection-history grounds,454 show very different interiors: [ref_arm_1890] PDF has large facets, while [ref_arm_2209] PDF has very small marks. Other examples that would fall under the proposed Bartel criterion include [ref_arm_1730] PDF [ref_arm_1728] PDF [ref_arm_1805] PDF [ref_arm_1804] PDF [ref_arm_1923] PDF [ref_arm_1856] PDF. Breastplate [ref_arm_3524] PDF, with excellent provenance, also has small marks. Attribution of all these objects to Bartel is highly unlikely.

Hammer marks may assist comparison within a pair: differences between left and right can suggest different manufacture or a later replacement. Their broader significance should not be overstated. Corrosion may obscure or imitate marks, and medieval armourers certainly used hammers of different sizes. Rejecting an object on mark size alone is therefore unsound, especially when catalogues omit interior photographs and readers cannot examine the evidence.

Originalwortlaut vergleichen
8.5.7 A recently sold helmet of type-VII  



While Boeheim intended to detect grooves on rolled plate under purposely applied hammer 



marks, other scholars assumed the same forger behind similar hammer -marks. In the 



catalogue of the 2011 Klingbeil Collection -sale, the description of Lot. No. 182 reads as 



follows:



[…] The interior shows unusual hammerwork, the result of using a 



hammer with a very small head. This style of workmanship is 



characteristic of Raymond Bartel, the armourer to William Randolph 



Hearst. A sallet of similar construction also showing characteristic small 



hammer marks was made by Bartel and included as an addition to the 



sale of the armoury of the Dukes von Ratibor , Galerie Fischer 



Waffensaal des Schlosses Grafenegg, II. Teil, May 2, 1934, lot 67.451 



The description is formulated very carefully, trying to avoid a final judgment on the 



authenticity of this helmet. Nevertheless, it is strongly suggesting that the helmet is a modern 



reproduction. The catalogue description of the quoted “sallet” [ ref_arm_5129] sold by 



Fischer in 1934 does not say that it was a reproduction made by Bartel.452 It was offered as 



a genuine item. It remains obscure, where the author of the in Bergé’s catalogue description 



got his information from. 



After Bergé’s catalogue was published, the author tried to find further proof for the 



suggestion that small ha mmer-marks are characteristic for Bartel’s works. One popular 



example of his work is the left hand -protection [ ref_arm_1147] at the Glasgow suit 



[ref_arm_4117] which he made as a replacement for the lost original. It is a copy of the 



extant right counterpart and was made when the suit came into the possession of William 



Randolph Hearst in the early 20 th century. Bartel marked his hand-protection at the interior 



of the cuff with a tilting helmet over the capital letters “R. B.”. It seems as if he did not use 



wrought-iron, as no delaminations are to be found. The plate does not show unusual hammer 



marks in teriorly. But hand -protections might require less forging -work and therefore the 



hammer-marks might be different to those found inside a helmet. There are certainly more 



of Bartel’s works still existing, but the author could not examine any helmet before this study 



was finished. 



The former owner of the concerned recently sold type -VII helmet, Karsten Klingbeil, in 



February 2011 gave permission to the author to examine some of his items. In this course, 



images of the helmet were taken, also of the interior hammer-marks [ref_arm_4242].453 How 



problematic it is to judge an item by hammer-marks only is explained in the following notes.  



In the DHM there is a helmet with eye -catching similar small hammer marks 



[ref_arm_1713]. This helmet has not been inventoried and has therefore no access number. 



Maybe future research will find out more on the provenance of this helmet. Interiorly the 



helmet shows a layer of a copper colored brazing-solder. The outer surface is brownish and 



rough, maybe from a treatment with an acetous liquid, either for cleaning off corrosion 



products or from imitating a patination. The plate at many locations shows delaminating 



layers typically for a mechanically refined iron. Its general shape is corresponding with many 



other similar items and is at no point uncovering an unprofessional hand. There is no 



evidence for this helmet being a reproduction.



Two similar helmets of type -VII in the HJRK show  clearly that genuine helmets 454 could 



show totally different interior hammer marks. While very large facets are visible at 



[ref_arm_1890], those inside [ref_arm_2209] are very small. The two Vienna helmets are an 



example for what the careful observer will recognize when looking at a huge number of 



different items: hammer marks can be very different from object to object and therefore they 



cannot serve as an indicator for authentic or not-authentic items. 



There are many more helmets that – according to their hammer marks – would have to be 



suspected to be made by Bartel, if the Bergé’s catalogue description is correct: 



[ref_arm_1730] [ ref_arm_1728] [ ref_arm_1805] [ ref_arm_1804] [ ref_arm_1923] 



[ref_arm_1856]. Also torso front -protections of the best provenance show small hammer 



marks at the interior e. g. [ref_arm_3524]. It is very unlikely that all these items were made 



by this modern armourer. 



Looking for hammer marks can only help when objects extant pair-wise are concerned. The 



difference from the left to the right counterpart of limb or hand -protections might suggest 



that the items were not made by one hand and that one of them could be a completion. 



Additionally it should be avoided to overestimate the significance of hammer marks for any 



question on the making of armour: Many extant objects had suffered so badly from corrosion 



that one cannot judge what mark derives from a hammer and what from rust. It needs no 



proof that certainly the armourers of the Middle Ages also did not all use one single hammer. 



For sure they also employed hammers with heads of different sizes . Thus the sizes of the 



hammer marks on genuine objects in some cases might show small dimensions. It is a very 



arguable approach to define a certain piece as a reproduction due to its hammer marks, 



especially as readers usually cannot check the truth of s tatements given. Catalogues do 



usually not include images of the object’s interior.
S. 219 · Sprachlich überarbeitet · Entwurf

8.6 New research approaches

The following pilot investigation explores whether internal material structures can provide additional evidence for manufacturing processes without damaging an object during imaging.

Originalwortlaut vergleichen
8.6 Ideas for new approaches
S. 219–220 · Sprachlich überarbeitet · Entwurf

8.6.1 Non-destructive examination by synchrotron radiation computed laminography

The aim is to identify internal features left by particular refining methods. Such signatures might help constrain the period in which an armour object could have been made. X-ray imaging offers a promising route because it can examine the interior without destructive sectioning.

Scientists at KIT and ESRF developed synchrotron radiation computed laminography (SRCL), using X-rays generated by an electron storage ring.455 Its high photon flux permits high-contrast images at resolutions around 1 µm. Beam energy can be selected to suit the material, geometry and research question. Access is the chief limitation: the method is complex and costly, and ESRF beamline ID15a was considered the likely suitable facility for this project.

The available energies permit examination of metal thicknesses below about 5 mm. Laminography is especially suited to broad, thin objects. The specimen rotates on a stage with an adjustable inclination relative to the beam; an angle of about 30° proved useful for many sheet-like samples. This geometry reduces the extreme changes in material path length encountered when a plate rotates in conventional CT, thereby limiting associated image artefacts. Features around 1 µm can be resolved. At the time of this investigation, it offered a particularly advanced approach to the problem.

Through Daniel Hänschke, then a doctoral researcher at KIT’s Laboratorium für Applikationen der Synchrotronstrahlung, three ESRF colleagues generously scanned samples supplied for this study. Hänschke processed the resulting image data.456 Four iron-based materials with different production histories were selected to test whether their refining structures could be distinguished non-destructively.

Each specimen measured about 1.0 × 5.0 × 5.0 mm. The linked three-dimensional reconstructions show a central volume of approximately 0.6 × 1.2 × 1.2 mm. The following descriptions distinguish known sample histories, expected features and observed structures.

Redaktionelle Hinweise · 3
  • Der Originalsatz zur „nearly constant wavelength“ verwechselt offenbar Strahlwellenlänge und geometrisch durchstrahlte Weglänge. Die geometrische Aussage ist entsprechend präzisiert und muss fachlich bestätigt werden.
  • Auflösung, Strahlführung und Verfügbarkeit beziehen sich auf den damaligen Versuch, nicht auf heutige Anlagen.
  • Die Bildgebung ist zerstörungsfrei; die Herstellung der kleinen Proben erforderte zuvor Materialentnahme. Keine zerstörungsfreie Untersuchung ganzer Panzerungsobjekte behauptet.
Originalwortlaut vergleichen
8.6.1 Perspectives for non-destructive metallurgical testing: Synchrotron 



Radiation Computed Laminography 



The author intends to find a sc ientific method suitable for the  non-destructive testing of 



armour. The desired result would be the detection of fingerprints which a certain refining 



method had imprinted into the structure of the armour material. Such fingerprints could help 



to narrow down the time frame in which a certain artefact might have been produced.  



X-ray based examination is certainly a reasonable choice whenever an artifact should be 



prevented from any damage. In the recent years scientists of the KIT and the ESRF 



developed a specialized X -ray based scanning method  called “ Synchrotron Radiation 



Computed Laminography (SRCL) ”455. This method uses synchrotron X -ray beams, 



produced by an electron storage ring. This method promises to surpass the aforesaid 



limitations of computed-tomography by the following advantages: 



- Better flux densities: This provides for the possibility of generating high resolution 



images of ~1µm, due to the increased number of X -ray beams per mm 2. The image 



contrast is very high. The used energy can be optimized for different ma terial, 



geometries or research questions.



The disadvantages are: 



- Access to devices: This method is extrem ely complicated and expensive. Probably 



only one “beamline” is suitable for the intended ex amination of armour plate : 



Beamline ID15a of the ESRF .  



The synchrotron technique provides beam-energies high enough to scan also thicker metal-



volumes (< 5 mm) . It is particularly suitable for the scanning of flat, laterally extended 



volumes: The sample is fixed to a rotating table. The angle-position towards the direction of 



the X-ray beams can be adjusted. It was found that a 30 degree angle in most cases is the 



best position to scan plate -like materials. By this method the beams travel with a nearly 



constant wavelength through the material. In comparison to conv entional CT-scanning, by 



this sample-positioning image-artifacts are reduced. The revealed images are of a very high 



resolution, i. e. inclusions or cavities of ~1µm size can be detected. Currently, f or the 



concerned testing of armour -plate no further-advanced imaging technology is available  in 



the entire world. 



Fortunately, the author was in good contact to Daniel Hänschke, a PhD student working at 



the Laboratorium für Applikationen der Synchrotronstrahlung (LAS) of the KIT. On his 



request, three of his colleagues researching at the ESRF  generously carried out scans of 



samples provided by the author. Daniel Hänschke processed the revealed image-data. 456 



Four samples of  differently refined iron samples were scanned. The intention was to non -



destructively visualize structural differences between the samples – left by different refining 



methods.  



Each sample had the size of about 1.0 x 5.0 x 5.0 mm. The 3 -D reconstructions (references 



in the headlines) show a volume of ca. 0.6 x 1.2 x 1.2 mm in close vicinity to the sample’s 



center. In the following, it will be described which parameters on each specimen were known 



and what was expected to be seen in the images. The results of the examination will be 



introduced and discussed.
S. 220 · Sprachlich überarbeitet · Entwurf

8.6.1.1 Sample 1: modern C45 steel

The three-dimensional defect reconstruction is available at [ref_vid_syn_c45]. This untreated modern C45 steel contained 0.45% carbon and was produced by the Linz–Donawitz process. Conventional metallography suggested that its interior should be comparatively homogeneous, with few inclusions. The scans show an otherwise unstructured volume containing only a few small, rounded dark features [ref_ill_syn_c45_xView] [ref_ill_syn_c45_yView] [ref_ill_syn_c45_zView].

Originalwortlaut vergleichen
8.6.1.1 Sample 1 [ref_vid_syn_c45] (3-D reconstruction of defects) 



This was a modern, not heat -treated steel (C45) with a carbon content of 0.45%, produced 



by the modern Linz -Donawitz-Method. It was expected that the images of the interior 



volume would show a homogenous structure with only little inclusions, analogue to existing 



metallographic examinations of such material. In the synchrotron -scans a homogenous, not 



structured mass with only few small globular dark areas is visible [ref_ill_syn_c45_xView] 



[ref_ill_syn_c45_yView] [ref_ill_syn_c45_zView].
S. 220–221 · Sprachlich überarbeitet · Entwurf

8.6.1.2 Sample 2: a historic hand-defence cuff

The reconstruction is available at [ref_vid_syn_ha]. The sample came from a badly damaged, corroded cuff dated to about 1600.457 Its fragmentary archaeological condition and negligible commercial value supported its selection as a genuine reference object. Visible delamination suggested mechanically refined material with an uneven, probably layered internal structure.

Views perpendicular to the plate surface clearly reveal layers [ref_ill_syn_ha_locA_xView] [ref_ill_syn_ha_locA_yView] [ref_ill_syn_ha_locB_xView] [ref_ill_syn_ha_locB_yView]. Parallel views [ref_ill_syn_ha_locA_zView] [ref_ill_syn_ha_locB_zView] show thin dark layers458 between brighter, nearly homogeneous ones. Both extend through almost the entire scanned volume. Dark layers are approximately 5–8 µm thick; bright layers are about twice as thick. A network of fine bright lines interrupts the dark layers, with the same orientation at successive levels.

Repetition on parallel planes makes randomly distributed smelting inclusions an unlikely explanation. The dark layers may instead mark former surfaces joined during refining. They could contain incompletely welded voids or scale trapped between the hot pieces. The bright network may identify areas where the adjacent ferritic layers welded fully.

Its consistent orientation remains unexplained. Possible causes include directional hammering, rolling, the orientation of the ferritic microstructure, or channels through which flux entered the weld interfaces. These alternatives require further investigation.

Redaktionelle Hinweise · 1
  • Geringer Marktwert und korrodierter Zustand allein beweisen keine Echtheit. Die Neubearbeitung benennt sie als Grundlage der Probenauswahl, ohne eine dokumentierte Grabungsprovenienz zu erfinden.
Originalwortlaut vergleichen
8.6.1.2 Sample 2 [ref_vid_syn_ha] (3-D reconstruction of defects) 



This sample was cut from a badly damaged and c orroded hand-protection-cuff457 of about 



1600. This item is certainly genuine, as it is preserved in archaeological condition, 



incomplete and of no value that would give any benefit to a forger. It was therefore expected 



that the material would be made by a pre-industrial wrought -iron process, showing an 



inhomogeneous, presumably layered defect structure. Delaminations were already visible at 



several spots of the cuff. The scan-images of the interior – orthogonal to the plate-surface –



clearly show a layered structure [ ref_ill_syn_ha_locA_xView] 



[ref_ill_syn_ha_locA_yView] [ref_ill_syn_ha_locB_xView] [ref_ill_syn_ha_locB_yView].  



In the views  in parallel to the plate surface [ ref_ill_syn_ha_locA_zView] 



[ref_ill_syn_ha_locB_zView], thin, dark458 layers in between nearly homogeneous brighter 



layers became visible – both crossing all the scanned volume with only few interruptions. 



The darker layers are about 5 to 8 µm thick and the brighter layers are approximately twice 



as thick. The dark layer is interrupted by a net of fine, brighter lines. The structures of each 



different dark layer are oriented to exactly the same direction. 



As these structures are found at several parallel levels, it is very likely that they do not derive 



from randomly arranged inclusions of the smelting process. It is more likely that the darker 



areas actually remark the lamellar welding seams,  actually the former workpiece -surface 



before the welding in the refining process. These areas  might be hollow spaces, emerged 



where the brighter layers had not entirely welded together or they are inclusions of hammer-



scale that occurred on the surface before the white -hot segments were welded together. In 



any case, the net of lines probably marks the locations where the different , bright ferritic 



layers actually welded together entirely. Why these nets are of an oriented structure cannot 



be explained yet. The orientation might derive from the equal hammering of the plate. It is 



also possible that the rolling of the plate might result in such a structure. A third explanation 



is that the orientation of the ferritic crystal -microstructure determines the orientation of the 



visible net -structure. Finally, the net might have been the “channels” through wh ich the 



welding fluxes penetrated the welding-seams.
S. 221 · Sprachlich überarbeitet · Entwurf

8.6.1.3 Sample 3: reported nineteenth-century puddled iron

The reconstruction is available at [ref_vid_syn_pud]. This material was supplied as nineteenth-century puddled iron, subsequently rolled from scrap into sheet.459 Its mechanical refining history suggested numerous inclusions or defects, potentially with a preferred orientation. Two locations were scanned.

Perpendicular views [ref_ill_syn_pud_locA_xView] [ref_ill_syn_pud_locA_yView] [ref_ill_syn_pud_locB_xView] [ref_ill_syn_pud_locB_yView] show narrow, plate-like dark features within brighter metal. They occur at different levels without matching neighbouring features. Parallel views [ref_ill_syn_pud_locA_zView] [ref_ill_syn_pud_locB_zView] show dark fibres aligned in one direction, repeatedly interrupted by fine bright lines transverse to their axes.

A dark layer crosses the entire central scanned volume. This may be a refining weld, but unlike the layers in sample 2 it comprises a more irregular assemblage of dark areas of different sizes. The fibres and narrow lamellae may be slag or voids elongated during forging and rolling.

Originalwortlaut vergleichen
8.6.1.3 Sample 3 [ref_vid_syn_pud] (3-D reconstruction of defects) 



This specimen is said to be a 19 th century iron, made in the puddle -process. The particular 



specimen was secondarily rolled into plate-dimensions from some scrap iron 459. Due to the 



manufactured refining of puddle-iron, it was expected that the interior structure would show 



many inclusions  or defects , probably arranged in an oriented structure. The sample was 



scanned at two different locations. The scan-images of a view orthogonal to the plate-surface 



[ref_ill_syn_pud_locA_xView] [ ref_ill_syn_pud_locA_yView] 



[ref_ill_syn_pud_locB_xView] [ref_ill_syn_pud_locB_yView] show narrow, lame-like dark 



structures inside a brighter surrounding volume. They are found on different levels and do 



not correspond with similar neighboring structures. The view in parallel to the plate-surface 



[ref_ill_syn_pud_locA_zView] [ ref_ill_syn_pud_locB_zView] clearly shows dark fibers, 



oriented to one direction. The fibers are repeatedly interrupted by fine, brighter lines, running 



orthogonally to the central fiber-axis. In the center of the sample, one dark layer – extending 



throughout all the scanned volume – is visible. This might be a laminar welding-seam from 



refinement, but, other than the darker layers in sample 2, this shows a more randomly 



arranged conglomeration of darker areas of  varying sizes. The fibers and the narrow lames 



are either slag inclusions or hollow spaces that got elongated by the forging and the rolling 



processes.
S. 221–222 · Sprachlich überarbeitet · Entwurf

8.6.1.4 Sample 4: a partly refined bloom

The reconstruction is available at [ref_vid_syn_blo]. Achim Wirtz produced this bloom in a traditional Japanese tatara furnace in 2010.460 The sampled material was at an early refining stage: heated to red heat and consolidated by hammering, but not folded and forge-welded.

The scans show comparatively large, nearly homogeneous regions separated by a few small, dark elongated features [ref_ill_syn_blo_xView] [ref_ill_syn_blo_yView] [ref_ill_syn_blo_zView]. Hammering had already spread inclusions or defects laterally into short fibres, while substantial volumes remained nearly free of visible inclusions.

Originalwortlaut vergleichen
8.6.1.4 Sample 4 [ref_vid_syn_blo] (3-D reconstruction of defects) 



This sample was cut from a bloom left in an early refining stage. The bloom was produced 



in a traditional Japanese Tatara-furnace by Achim Wirtz in 2010460. The spongy bloom had



been red-heated and simply forged by the hammer. The volum e had not been folded and 



forge welded. It shows comparatively large, nearly homogeneous sections with only few 



small darker, elongated areas in between [ref_ill_syn_blo_xView] [ref_ill_syn_blo_yView] 



[ref_ill_syn_blo_zView]. It is interesting to see that the hammer-forging had already resulted 



in the inclusions or defects becoming laterally extended or elongated in short fibers . 



Nevertheless, comparatively large areas are nearly free of inclusions.
S. 222–223 · Sprachlich überarbeitet · Entwurf

8.6.1.5 Outlook

The four specimens show clearly different structures, offering clues to their production histories. Conventional metallography of the same samples would provide a useful comparison. Sections of sample 2 parallel to the sheet should be examined particularly closely to determine whether its network also appears under the microscope.

The nearly inclusion-free layers in that sample demonstrate a crucial sampling limitation. Examining only one such layer could misrepresent the whole sheet and lead to a mistaken classification as modern homogeneous steel. Visible delamination, layered inclusions or fibrous structures are important evidence of mechanical refining, and three-dimensional examination across the thickness can reveal features missed by a small isolated sample.461

The distinction proposed here is between later liquid-state steelmaking, industrially established from the 1860s, and mechanically refined iron or steel. The former generally produces comparatively homogeneous material without repeated-welding structures. The latter includes both direct bloom refining and indirect refining of cast iron, followed by consolidation and welding. Puddling, developed from the mid-eighteenth century and used into the 1920s, belongs to the latter group. Such processes commonly leave inclusions and weld-related defects, although their visibility and distribution vary.

Recognising mechanically refined material does not establish medieval manufacture: nineteenth-century reproductions could use puddled iron. Distinguishing direct-process material from later puddled stock remains insufficiently studied. Differences in inclusion shape might also distinguish hammered from rolled sheet. Since rolling is not thought to have been established before the late seventeenth century, a demonstrably rolled sheet would exclude manufacture as original late medieval armour. Diagram [ref_ill_dia_aut] summarises the proposed reasoning.

A controlled experimental programme should produce material by both direct and indirect routes, forge-weld it, then divide each batch between rolling and hammering to sheet thickness. Synchrotron laminography could test whether these operations reproduce the observed networks and whether their effects can be distinguished. Historic reference materials should also be examined to enlarge the comparative dataset.462

By the time this dissertation went to press, approximately fifty-five further iron samples had been scanned at ESRF with a collaborating team. Their images still awaited interpretation, with publication planned subsequently.

Redaktionelle Hinweise · 3
  • Der Originalausblick erklärt Einschlüsse zugleich als unvermeidlich und diskutiert zuvor einschlussarme alte Werkstoffe. Die Neubearbeitung hält die konkrete Beobachtung und ihre Verteilungsabhängigkeit fest, statt den Widerspruch zu verallgemeinern.
  • Vier Proben erlauben keine validierte allgemeine Datierungsmethode. Beobachtete Unterschiede und vorgeschlagene Folgeversuche bleiben getrennt.
  • Die Angabe weiterer 55 Proben ist ein historischer Projektstand der Dissertation; keine Aussage über deren heutigen Auswertungsstand.
Originalwortlaut vergleichen
8.6.1.5 Outlook 



The structures of all four samples clearly differ from each other. This delivers hints on how 



the material might have been refined. It would be interesting to examine the same samples 



with the help of conventional metallographic methods. Especially sections of sample 2 in 



parallel to the plate-surface should be examined, to test if the net structure also becomes 



visible in the microscopic images. One conclusion very important for the appraisal of 



conventional metallographic testing can be drawn. In the images of sample 2, layers nearly 



free of inclusions are visible. This suggests that a metallographic examination of one layer 



only might not be representative for the whole of the material. An incorrect sampling might 



lead to the mistaken conclusion that the examined material would not be wr ought-iron, but 



rather modern steel, as the volume would show no impurities. One fact needs to be 



considered for the examination of any iron based material: All material that is obviously 



delaminating or if microscopic or X-ray images show a layered or a fiber structure, is actually 



produced by a wrought -iron technique. An examination of the entire plate -section in 3D is 



indispensable for the detection of such structures.461  



As said above, objects of art might have been produced of two types of iron or steel:  



1. Mild-steel, which is a modern, since the 1860s industrially processed iron based -



material. It is nearly free of defects, without refining -structures, and with 



homogeneously spread chemical components (Bessemer, Thomas-Martin, Donawitz 



et al.). 



2. Wrought-iron which was produced either by mechanically cleaning a bloom (direct 



process: forging, folding, fire -welding) or since the 14th century by reducing the 



carbon content of cast -iron (indirect process: oxidizing condition in a refining -



furnace, further welding and fire-welding necessary). One of these indirect-methods 



is the so-called “puddle-process”, developed from the mid-18th century on and used 



until the 1920s. Wrought -iron produced by any of these methods inevitably shows 



impurities (slag incl usions, hammer -scale, charcoal, welding fluxes) and defects 



induced by the fire-welding process.  



Established methods for metallographic analysis allow a confident differentiation between 



wrought-iron (inclusions, defects, fibred or layered structure) and mild steel (homogeneous)



only. However, an item determined to consist of wrought -iron could be a modern (19th 



century) reproduction made of puddle -iron. Only insufficient scientific attempts have been 



made to tell the younger puddle-iron material (indicating forgeries) apart from the wrought-



iron produced by older techniques. For a differentiation, it can be expected that, concerning 



the microstructure, material made by the puddle process differs from material produced by 



the direct process. On the same con cern, a further crucial fingerprint could result from the 



fact that the rolling of plate was not developed before the late 17th century. The material of 



ancient armour had to be forged into billets and subsequently into plates by means of a 



powered hammer.  Essential indications will therefore be provided by differences in the 



morphology of inclusions between rolled and hammered plate. The diagram [ref_ill_dia_aut] 



tries to visualize the conditions on how plate-armour material might be classified as genuine 



or modern.  



Future, improved studies of historical iron -based material might help to tell by which 



production technique the material of an iron artwork had b een made. For such studies, t he 



author suggests reproducing a forge -welded iron from material produced by the direct 



process and a second one produced by the indirect process. One part of each of these 



materials should be rolled; another part should be hammer-forged into the dimensions of thin 



plate. Such material could be scanned by synchrotron-laminography. The results might tell, 



if the net structure can be reproduced and if the refining -processes, the rolling or the 



hammering would result in different s tructures. Plate was most likely not rolled before the 



second half of the 17 th century. If structures could clearly be distinguished, in the future it 



might be possible to tell if an item was made of rolled wrought-iron plate and could thus not 



be genuine. Also further tests 462 of historical materials are necessary to assemble a wid er 



data basis for comparisons.  



By the time this paper was printed , the author together with a team of other scientists had 



already scanned about 55 further iron samples at the ESR F . The images are waiting to be 



interpreted, the results will subsequently be published.
S. 223–224 · Sprachlich überarbeitet · Entwurf

8.6.2 An invitation to interdisciplinary research

The humanities and natural sciences have not yet collaborated closely enough on these questions. Metallurgical studies have often assumed authenticity without systematically comparing historical material and reproductions. Humanities scholarship, meanwhile, has not adequately assembled manufacturing sources or presented its findings in a form that enables materials specialists to design new tests.

Understanding complex craftsmanship also requires practical engagement. Reading descriptions or watching demonstrations alone is rarely sufficient. Researchers need not become master armourers, but should experience how hot metal responds to hammering and how steel resists a file, saw or grinding tool. Combining that experience with scholarship gives a fuller understanding of the object, just as trying an instrument helps a listener appreciate a performer’s work.

This dissertation originates in art history and was necessarily limited by time and resources. Metallurgical investigation requires specialist collaboration. Formal and technical observations become useful only when comparable data exist for other objects. Small datasets risk circular reasoning and disproportionate influence from unidentified replacements or reproductions. Larger, carefully documented comparisons are essential, informed by the techniques available both during the principal armour-making period, 1350–1650, and during reproduction from 1800 onwards.

Materials scientists accustomed to standardised modern products face a difficult task in interpreting variable historic methods. Their expertise is nevertheless indispensable for developing approaches beyond the limitations of conventional tests. Gerhard Sperl, for example, proposes investigating Ostwald ripening as a possible means of dating iron. This merits further work, though the method damages at least a small area of the object.463

Priority should be given to non-destructive approaches. Repeated sampling by successive generations risks gradually consuming the evidence [ref_ill_art_5388] PDF. Conventional and synchrotron X-ray imaging may reveal distinctive structures, textures or compositional patterns left by different production methods. Testing that possibility requires sustained collaboration.

Redaktionelle Hinweise · 1
  • „Oswald-Reifung“ im Original wurde zur fachüblichen Schreibweise „Ostwald ripening“ normalisiert. Der Datierungsansatz bleibt ein Forschungsvorschlag.
Originalwortlaut vergleichen
8.6.2 An appeal to all interested scientists 



Until today, the mental arts and the natural sciences had not worked together closely enough 



on interdisciplinary approaches to the aforesaid problems. The disciplines did not really learn 



from each other’s experience. William’s metallurgical approaches ig nored the question of 



authenticity and did not compare wrought-iron to mild-steel metallurgy. The approaches of 



the humanities on the other hand did neither research the historical sources on the armour-



making technologies, nor did they summarize their past findings in a way that would provide 



an understandable and comprehensive overview to the natural scientist – an indispensable 



platform for the latter to develop advanced testing-methods.  



In the case of describing complex products of elaborate craftsmans hip, the need for the 



understanding of technologies becomes indispensable. Only reading about them or watching 



others executing them is usually not enough. A somewhat uncommon demand on scholars 



working on the subject should be made here: The describer’s hands need to feel the processes 



that lead to a ready product. This does not mean that the scholar has to become a master 



craftsman or artist himself. But he has to feel how a white-hot metal is reacting when beaten 



by a hammer; he has to feel the resistance of steel when it is filed, sawn or ground. Only the 



combination of academic knowledge and the personal experience of simple craftsmanship 



will allow him to draw a complete picture of the artifacts he is about to examine. Just like it



is necessary for a non-musician to once sit down at the piano and to try to repeat the pianist’s 



performance if he wants to get an idea of the effort it takes to compose and/or to render a 



beautiful song. This study is based in the art history -discipline. The time range and t he 



financial possibilities of this thesis were limit ed. Metallurgical testing can only be 



undertaken with the help of specialists.  



The examination of formal and technological features would only deliver useful information, 



if the revealed data could be co mpared to the same data -classes tested on other examples. 



The smaller the choice of samples, the higher is the risk of including circular arguments 



within a final statement, as data deriving from reproduced or altered parts may have a greater 



influence on any result. With a larger quantity of pieces to be compared, the quality of the 



data would raise. For the correct interpretation of the revealed data, the understanding of the 



historical techniques of armour manufacture is indispensable. This would include  the 



understanding of the techniques available in both times – the classical plate-armour period 



from 1350 to 1650 and the period of reproductions from 1800 until today.  



It is of course difficult for scientists specialized on the testing of modern materia ls to 



familiarize with the various aspects of ancient, not standardized techniques. As explained 



above, the conventional testing methodologies provide only limited possibilities for 



authenticity-testing. The involvement of specialists is nevertheless indis pensable, as only 



they can imply all the possibilities that not yet considered sophisticated testing -methods 



might provide for new approaches to the authenticity problem. For example , an interesting 



approach to the dating of metals provided in a comprehensive manner by Gerhard Sperl can 



be developed further. He suggests that the methodology of observing the “Oswald-Reifung” 



on iron-artifacts could help to date the material. Nevertheless, it has to be anticipated that 



this technique is not unproblematic, as it damages at least a small spot of the examined 



object.463 



The author of the present paper suggests focusing on the non-destructive testing-methods. If 



each generation of scientists would have to damage the artifacts to get to a result, in the end 



nothing would be left to examine [ref_ill_art_5388]. Existing X-ray based analysis-methods, 



such as 3D -imaging provided by conventional or synchrotron computed -tomography, can 



possibly be advanced for approaches to the topic. Maybe the different techniques of different 



times left some sort of distinctive fingerprint on the microstructure, e. g. the texture, and the 



chemical composition.

9 Summary

S. 225–226 · Sprachlich überarbeitet · Entwurf

9 Summary

This study seeks to broaden our understanding of late medieval European plate-armour production and provide a basis for further research. Its most lasting contribution may be the digital collection of a large body of objects and comparative material. Although the records remain incomplete, they offer a substantial foundation that can be extended to later armour and to historic depictions.

Collaboration with Christopher Retsch, then a postgraduate at the University of Bamberg studying armour in late medieval effigies, already demonstrated the value of this approach. His findings informed this dissertation, while he used its database and emerging conclusions in his own work.

The proposed terminology made it possible to organise a large and varied body of evidence using a relatively small set of defined types and terms. Charts and illustrations clarify their relationships. Readers may initially need time to become familiar with the definitions, but those definitions are now explicit and open to discussion. They will undoubtedly need revision and expansion, including to tournament equipment and earlier or later forms. An internationally usable terminology could make communication clearer and help resolve longstanding questions about the craft.

The technological history examines how armourers balanced protection, movement and wearability. It classifies combinations of types across periods and regions, offering another perspective alongside the familiar relationship between armour and clothing fashion. Many constructional solutions remained in use across regional boundaries for long periods. Makers evidently exchanged or copied technical ideas as well as stylistic features.

The chapter on technical features contains the study’s principal findings. Systematic comparison of construction reveals groups that cross conventional type boundaries. Certain copper-alloy fittings, turned edges and other details can be associated with regions, periods or sometimes makers. Articulated joints are classified and explained, while dimensions and weights offer evidence relevant to custom manufacture. Their implications for authenticity are considered throughout.

The aim was not to replace the history of armour entirely, but to add explicit, comparable observations to a field often approached primarily through aesthetics. These observations can support more precise descriptions, and the database offers extensive possibilities for further comparison. I hope it will eventually become accessible to every researcher.

Supplying trades remain an underexplored field. The brief chapter devoted to them shows that armour’s production value was created beyond the armourer’s own workshop. Essential tools, fittings and materials came from several crafts. Further research could clarify what armourers made themselves and what they purchased, deepening our understanding of the many technologies combined in a single object.

The discussion of preservation and authenticity cannot resolve every uncertainty introduced by time, collecting and restoration. It does, however, bring together the main issues and establish directions for further work. Archival research into the nineteenth-century reproduction trade may identify surviving products and their makers. Many reproductions probably remain in collections, including hundreds beyond this study’s scope. Potential projects include suits at Burg Ranis, Hohenschwangau, Cologne’s Stadtmuseum and the Palazzo Venezia in Rome. The history of restorers deserves equal attention. Scientific examination, combined with documentary and object research, may yield further results.

The metallurgy chapter lays groundwork for such collaboration. It reviews historic ironmaking, reconstructs sheet production from written sources, and assesses methods for investigating quality and authenticity. The preliminary three-dimensional imaging results point towards a promising experimental programme.

The final chapter considers attribution to periods, places and makers, alongside authenticity. Detailed cases show why conclusions must remain tied to explicit evidence. The project also initiated collaborative research into non-destructive examination of armour material.

I hope this work contributes to a fuller account of both the production and reproduction of late medieval plate armour. Images and videos are provided wherever possible to make the reasoning traceable. Above all, the aim has been to establish a durable body of evidence, combining earlier scholarship with new observations, on which future research can build.

Every study must eventually give way to discussion. May the proposals offered here encourage further investigation and a better understanding of an accomplished, now largely lost craft: the making of plate armour.

Redaktionelle Hinweise · 2
  • Die unvollständige Ortsangabe „DE – suit“ in der Original-Aufzählung ist im überarbeiteten Fließtext ausgelassen, im Originalauszug erhalten. Kein fehlender Sammlungsname erfunden.
  • Zusammenarbeit, Datenbankzugang und Untersuchungsstand sind Aussagen zum Zeitpunkt der Dissertation.
Originalwortlaut vergleichen
9 Summary 



So what is the outcome of this study? Is the picture of late medieval European plate armour 



production now more complete? Can the findings promote future studies on the subject? 



For future studies on late medieval - and maybe also later armour - certainly the most 



important outcome of this research project is the digital collection of so many artworks. Even 



though the data is not completed yet, it builds a stable basis to build on. Furthermore, the 



concept of the database is suitable to get extended to armour of later times, but also to 



depictions of armour i n artworks. The author already encouraged a young postgraduate, 



Christopher Retsch from the University of Bamberg, to study armour rendered in late 



medieval effigies. The cooperation between both projects is already fruitful. The author 



could already use for this paper a lot of information provided by C. Retsch and the latter 



already uses the author’s database and the findings of this paper in return. 



The terminology suggested proved to be useful to oversee the huge amount of data and 



information that entered this study. The terminology-jungle could be reduced to a really low 



number of distinct types and terms, charts and images helped to visualize the classification 



structure. Anyway, at the beginning it might be difficult for the reader to follow the author’s 



thoughts and to remember the different definitions. Nevertheless, future preoccupations with 



the topic now can discuss and possibly improve the suggested definitions. There are certainly 



many open questions; some terms and types might have to be altered; the terminology needs 



to be extended to other armour groups e. g. tournament armour. Further type-differentiations 



might become necessary for the description of contemporary, earlier and later armour parts. 



An internationalization of the terminology can help to shorten communication ways, to make 



them faster and to avoid misunderstandings. This will provide the basis for the reconstruction 



of many unclear questions on the armourer’s craft. 



The brief history of plate armour from a technological point of view provided an insight on 



the armourer’s constructional considerations, on how he met with the demands of wearability 



and security. For the first time type-combinations common in different t imes and regions  



were closely described and classified . The author’s systemization shed a new light on the 



development of armour, aside from the often quoted mutual influences of armour and 



clothing-fashion. It became clear that many construction -variations were actually in use 



across regional borders throughout a longer period. The armourers obviously exchanged or 



copied not only stylistic, but also constructional details with or from each other.  



The chapter on technological features probably provides the  key-findings of this study. For 



the first time constructional details were compared and classified with such care. The 



comparison of the defined features help to identify cross -type groups of armour. Some 



features – like copper-alloy applications or turne d edges – could be attributed to certain 



regions, times or even masters. For the first time , the different joint -variations found on 



extant armour were classified and explained. Comparisons of dimensions and weight 



allowed suggestions on the customization of the items. Wherever findings could help to 



approach the question on authenticity, different aspects and considerations were discussed 



closer.  



This study did not intend to write the history of armour entirely new. Nevertheless, the new 



approach to the t opic from a technological point of view delivered several “hard facts” on 



different or common features found at two or more items. In the future, descriptions could 



become more precise than they had been in earlier publications that usually approached the 



topic from an esthetics point of view. The database assembled for this study provides nearly 



endless possibilities for further comparisons that promise a lot of new findings. This database 



will hopefully be accessible for any researcher one day.



A yet unwo rked field of research is on the craft s that supplied tools  and parts to the 



armourers. In a short chapter on this topic the author tried to show that the value adding of 



armour production was not only carried out in the armourer’s workshop. The armourers 



depended on a number of crafts that had to deliver various indispensable products. These 



considerations show once more how many different materials and technologies were 



combined in a product like armour. Future research on this topic might help to find additional 



aspects and to further differentiate between what an armourer made himself and what he 



actually bought in. 



The discussion on the history of armour preservation and the closely linked problem of 



authenticity cannot provide the whole picture of the topic of the omnipresent confusion on 



facts about extant historical armour, caused by the ravages of time. Nevertheless, this chapter 



for the first time provides a detailed overview on this important topic. More intense 



document-studies on the reproduction -industry of the 19 th century will certainly reveal 



important findings that might also be connected to existing artifacts. It is very unlikely that 



many reproduced items were destroyed throughout the last 200 years. If this is correct, the 



items must still exist. There are hun dreds of presumably reproduced items in various 



collections that were not included in this study. There is a good chance that the maker of 



many of such armour-suits or- parts can still be tracked down. A research project could focus 



especially on the histo ry of these items (Burg Ranis, DE – suit; Hohenschwangau; 



Stadtmuseum Köln, DE – suit; DE – suit; Palazzo V enezia, Rome, IT – suit etc.). Also 



research on the restorers of ancient arms and armour might shed more light on the problem 



of reproductions and restorations. Last but not least, different natural-scientific examination 



methods might reveal new recognition. The key to success might be intense interdisciplinary 



cooperation.  



In the chapter on the metallurgy or armour production the author tried to bui ld the basis for 



future interdisciplinary approaches. Starting from the discussion of historical iron production 



techniques, for the first time source-based reconstructions on the historical method of plate-



production were demonstrated. Different methods for the metallurgical testing of armour on 



quality and authenticity questions were discussed. The study ends with suggestions on future 



interdisciplinary approaches. Finally, the preliminary results of a promising 3D imaging 



method were presented. 



In the la st chapter practical advices for approaches to the mapping of plate armour to the 



times of its production, to the place of its production, to its maker and to its authenticity. The 



authenticity of single chosen objects and object groups is discussed in details. Finally some 



ideas for new, interdisciplinary approaches are quoted. The author was able to initiate a new, 



promising project on the non destructive authenticity testing of armour. 



The author hopes to have contributed to the completion of the perspective on the production 



and reproduction of late medieval plate armour. He has tried to provide as much information 



as possible in images or videos to ease the traceability of his thoughts. It was his special wish 



to provide a stable data basis – assembled from preceding studies and new findings – from 



which the research on historical armour can start into a new age.  



At a certain stage each scientist has to end the search for further perceptions and to open the 



discussion on the various introduced suggestio ns. May this be fruitful and may it help to 



better understand an artistic , but unfortunately nearly vanished craft – the craft of the 



armourer!

Appendix, acknowledgements and references

S. 227 · Sprachlich überarbeitet · Entwurf

Appendix

The original publication supplied reference files on an accompanying DVD. In the digital edition, use the reference links in the text to open the corresponding files.

I sought permission to reproduce all images supplied by other photographers. If any rights issue has been overlooked, please contact me so that the rights holder can be compensated at the customary rate.

Redaktionelle Hinweise · 1
  • Der Rechtehinweis gibt die Erklärung der veröffentlichten Dissertation sprachlich überarbeitet wieder. Er dokumentiert keine neue Rechteklärung und keine Freigabe für eine erneute öffentliche Veröffentlichung.
Originalwortlaut vergleichen
Appendix 



For all references see the attached DVD or (when reading the file on a computer) use the 



hyperlinks in the text. 



The author tried to get permission for the publishing of each of the images taken by other 



photographers. Whenever copyright issues might be offended, please contact the author and 



the right-owner will be reimbursed according to the common fees.
S. 228–230 · Sprachlich überarbeitet · Entwurf

Acknowledgements

I am grateful to the staff of the many collections I visited, and to the friends who offered accommodation and practical support. Their generous advice and assistance made this project possible. I cannot name everyone who helped, but my thanks extend to all who contributed.

Scholarship

This study could not have been completed without the Gerda-Henkel-Stiftung in Düsseldorf. Its generous support provided a monthly scholarship for thirty-two months and substantial funding for most of the necessary collection visits. My heartfelt thanks to everyone at the foundation.

Collections

  • Germany: Germanisches Nationalmuseum Nürnberg — Dr Baumeister; Bayerisches Armeemuseum Ingolstadt — Dr Müller, Herr Sieker and Herr Wirth; Augustinermuseum Freiburg — Dipl. Rest. Kai Miethe; Staatliche Kunstsammlungen Dresden — Dr Klatte, Dr Schuckelt, Frau Bohn and Herr Pelzl; Deutsches Historisches Museum Berlin — Dr Lüken, Herr Hohrath M.A. and Herr Wiehagen; Kunstsammlungen der Veste Coburg — Dr Alfred Geibig.
  • Switzerland: Historisches Museum Basel — Dr Egger and Herr Sauter; Zeughaus Solothurn — Dr Nater and Dr Mäder; Historisches Museum Bern — Herr Reichen; Schloss Grandson — Mr and Mrs Ashdown and Mr Embleton; Musée d’art et histoire Genf — Dr Godoy; Musée de Valere Sitten — Mrs Providoli; Musée gruerien Bulle — Mrs Raboud; Schloss Lenzburg — Herr Brack; Historisches Museum Luzern — Dr Horat and Herr Hofer; Musée Le Landeron — Mr Rickli and Mr Lehmann; Schweizerisches Nationalmuseum Zürich — Dr Hebeisen and Herr Mathys.
  • Austria: Hofjagd- und Rüstkammer Wien — Dr Beaufort-Spontin, Dr Pfaffenbichler, Frau Angermann and Frau Fuchs; Wien Museum — Dr Öhlinger, Herr Philipp and Frau Künzle; Oberösterreichisches Landesmuseum Linz — Frau Mag. Streitt.
  • Belgium: Diest; Liége — Dr Joris; Brüssel — Dr De Gruyse and Herr Theunis.
  • Turkey: Askeri Müze — Col. Tütüncüoglu, Inst. Maj. Avsar, Tünay Gückiran, Türkhan Erim, Özkan Kirgiz, Irem Tatli, Muharrem Tekran and Ridvan Önat.
  • Greece: Greek National Museum Athens — Mr Kachrilas.
  • United States: Metropolitan Museum of Art New York — Dr Phyrrh, Dr La Rocca, Mr Breiding and Mr Tavares; Art Institute Chicago — Dr Neet; Detroit Institute of Art — Dr Darr and Mrs You; Cleveland Museum of Art — Dr Fliegel and Dr Micolic; Higgins Armoury Worcester — Dr Foregeng; Philadelphia Museum of Art — Dr Terjanian.

University of Heidelberg: Professor Matthias Untermann and Professor Stefan Weinfurter.

Friends and relatives

My thanks to Achim Wirtz, Max Müller, Max Kluger, Andreas Petitjean, Christian Becker, Martin Siennicki, Andreas Appich, Céline Hundertpfund, Rebecca Hufnagel, Benjamin Goll, Kerstin Goll, Irene Goll, Gerd and Gerlinde Becker, Daniel Hänschke, Wolfram Wörner, Sabine Benning, Frank Unrath, Axel Nitsche and Jürg A. Meier.

For their consistently valuable contributions, I thank Peter Müller, Christopher Retsch, Jens Sensfelder and Dieter Graf.

Very special thanks go to Tobias Pfeiffer, who programmed the database with patience, insight and generous support.

Above all, I thank my wife Daniela and my son Theo Goll, who helped me through the difficult moments of this work.

Redaktionelle Hinweise · 1
  • Personen- und Institutionsnamen sind aus der Vorlage übernommen, abgesehen von eindeutigen extraktionsbedingten Leerzeichen. Schreibweisen wie „Phyrrh“, „Foregeng“ und türkische Namen sollten vor Veröffentlichung vom Autor bestätigt werden. Keine Personen ergänzt oder entfernt.
Originalwortlaut vergleichen
Acknowledgements 



The author is indebted to the many helpful responsible of most of the visited collections and 



to a number of good friends who helped out with a bed or other support. The persons named 



in the following were always at hand with friendly and helpful advice and act. It is impossible 



to name all those that finally helped to finish this research project. For everyone who took 



part in any way: Thanks for all the support! 



Scholarship 



This study would never have been finished without the generous help of the Gerda-Henkel-



Stiftung (Düsseldorf, Germany). 32 months I was granted my monthly scholarship plus a 



great financial support for most of the necessary collection-trips. Thanks to all people of the 



“Gerda”! 



Collections 



Germany 



Germanisches Nationalmuseum Nürnberg – Dr. Baumeister  



Bayerisches Armeemuseum Ingolstadt – Dr. Müller, Herr Sieker, Herr Wirth 



Augustinermuseum Freiburg – Dipl. Rest. Kai Miethe 



Staatliche Kunstsammlungen Dresden – Dr. Klatte, Dr. Schuckelt, Frau Bohn, Herr Pelzl 



Deutsches Historisches Museum Berlin – Dr. Lüken, Herr Hohrath M.A., Herr Wiehagen 



Kunstsammlungen der V este Coburg – Dr. Alfred Geibig 



Switzerland  



Historisches Museum Basel – Dr. Egger, Herr Sauter 



Zeughaus Solothurn – Dr. Nater, Dr. Mäder 



Historisches Museum Bern – Herr Reichen 



Schloss Grandson – Mr. Ashdown, Mrs. Ashdown, Mr. Embleton 



Musée d’art et histoire Genf – Dr. Godoy 



Musée de V alere Sitten – Mrs. Providoli 



Musée gruerien Bulle – Mrs. Raboud 



Schloss Lenzburg – Herr Brack 



Historisches Museum Luzern – Dr. Horat, Herr Hofer 



Musée Le Landeron – Mr. Rickli, Mr. Lehmann 



Schweizerisches Nationalmuseum Zürich – Dr. Hebeisen, Herr Mathys 



Austria 



Hofjagd- und Rüstkammer Wien – Dr. Beaufort -Spontin, Dr. Pfaffenbichler, Frau 



Angermann, Frau Fuchs 



Wien Museum – Dr. Öhlinger, Herr Philipp, Frau Künzle 



Oberösterreichisches Landesmuseum Linz – Frau Mag. Streitt 



Belgium 



Diest



Liége – Dr. Joris 



Brüssel – Dr. De Gruyse, Herr Theunis 



Turkey 



Askeri Müze – Col. Tütüncüoglu, Inst. Maj. Avsar, Tünay Gückiran, Türkhan Erim, Özkan 



Kirgiz, Irem Tatli, Muharrem Tekran, Ridvan Önat 



Greece 



Greek National Museum Athens – Mr. Kachrilas 



United States 



Metropolitan Museum of Art New York – Dr. Phyrrh, Dr. La Rocca, Mr. Breiding, 



Mr.Tavares 



Art Institute Chicago – Dr. Neet 



Detroit Institute of Art – Dr. Darr, Mrs. You 



Cleveland Museum of Art – Dr. Fliegel, Dr. Micolic 



Higgins Armoury Worcester – Dr. Foregeng 



Philadelphia Museum of Art – Dr. Terjanian



University of Heidelberg 



Prof. Matthias Untermann, Prof. Stefan Weinfurter. 



Friends and relatives 



Achim Wirtz, Max Müller, Max Kluger, Andreas Petitjean, Christian Becker, Martin 



Siennicki, Andreas Appich, Céline Hundertpfund, Rebecca Hufnagel, Benjamin Goll, 



Kerstin Goll, Irene Goll, Gerd and Gerlinde Becker, Daniel H änschke, Wolfram Wörner, 



Sabine Benning, Frank Unrath, Axel Nitsche, Jürg A. Meier.  



For a permanently fruitful input many thanks to: Peter Müller, Christopher Retsch, Jens 



Sensfelder and Dieter Graf. 



V ery special thanks to Tobias Pfeiffer, who programmed my database with a lot of patience 



and productive support. 



Special thanks to my wife Daniela and to my son Theo Goll, who both often helped me to 



get over the hard times I had with this work…
S. 231–240 · Quellenangaben übernommen

References

Agricola, G., 1977. Vom Berg- und Hüttenwesen: Zwölf Bücher vom Berg- und Hüttenwesen, München.

Anonymous, definition of "alloy", in: Encyclopaedia Britannica.

Anonymous, 1930. Educational charts of arms and armor: Metropolitan Museum of Art, New York.

Anonymous, 1983. Historisches aus der Geschichte der Blechfabrikation. Blech Rohre Profile 30 (3), 118–122.

Anonymous, 1987. Über die Blechfabrikation um 1860 bis 1890. Blech Rohre Profile (5), 401–403.

Anonymous, 1828. Wie viel Nägel ein geschikter Nagelschmied in einer Woche ohne Maschine fertigen kann. Dinglers's Polytechnisches Journal (27), 464.

Anonymous, 1880. Das Eisenhüttenwesen in Deutschland. Dinglers's Polytechnisches Journal (238), 77–88.

Anstruther, I., 1963. The knight and the umbrella: An account of the Eglinton Tournament 1839, London.

Appelt, H. (Ed.), 1988. Terminologie und Typologie mittelalterlicher Sachgüter: Das Beispiel der Kleidung; internationales Round-Table-Gespräch, Krems an der Donau, 6. Oktober 1986. Veröffentlichungen des Instituts für Mittelalterliche Realienkunde Österreichs 10, Wien.

Avinash C. Kak, M.S., 2001. Principles of Computerized Tomographic Imaging, Philadelphia.

Bargel, H.-J., 2012. Werkstoffkunde, 11th ed., Berlin.

Bartl, A. (Ed.), 2005. Der "Liber illuministarum" aus Kloster Tegernsee: Edition, Übersetzung und Kommentar der kunsttechnologischen Rezepte, Stuttgart.

Bauer, S., Demmler, T., 1941. Deutsche Ritterdenkmäler in Römhild. Der eiserne Hammer 61, Königstein im Taunus.

Bäumel, J., 2004. The Dresden Armory, 2nd ed., München.

Beabey, M., Richardson, T., 1997. Hardened leather armour. Royal Armouries yearbook, 64–71.

Berbenni, A., 1973. Encyclopaedia cinematographica: Central Europe - Lombardy. Forging of buckets for brickwork in a waterpowered hammer-mill., Göttingen.

Berger, D., 2006. Steingussformen aus dem spätromanischen-frühgotischen Magdeburg: Archäometrische und experimentalarchäologische Untersuchungen zum mittelalterlichen Zinnguss an ausgewählten Fundstücken. Diplomarbeit, Freiberg.

Blair, C., 1972. European armour: Circa 1066 to circa 1700, Repr. ed., London.

Blair, C., 1983. Notes on Armour from Chalcis, in: The International arms & armour exposition. The Dorchester Hotel, 3-5 November 1983, London, pp. 7–14.

Boccia, L.G., not dated. The Xalkis funds in Athens and New York.: Unpublished manuscript preserved in the library of the Royal Armouries in Leeds.

Boccia, L.G., 1982. Le armature di S. Maria delle Grazie di Curtatone di Mantova e l’armatura lombarda del ‘400, Bramante.

Boccia, L.G., Coelho, E.T., 1967. L' arte dell'armatura in Italia, Milano.

Boeheim, W., 1889. Werke Mailänder Waffenschmiede in den kaiserlichen Sammlungen.

Jahrbuch der Kunsthistorischen Sammlungen, Wien (9), 375–418.

Boeheim, W., 1891. Augsburger Waffenschmiede: Ihre Werke und ihre Beziehungen zum kaiserlichen Hof und zu anderen Höfen. Teil I. Jahrbuch der Kunsthistorischen Sammlungen, Wien (12), 165–201.

Boeheim, W., 1892. Augsburger Waffenschmiede: Ihre Werke und ihre Beziehungen zum kaiserlichen Hof und zu anderen Höfen. Teil II. Jahrbuch der Kunsthistorischen Sammlungen, Wien (13), 202–222.

Boeheim, W., 1893. Augsburger Waffenschmiede: Ihre Werke und ihre Beziehungen zum kaiserlichen Hof und zu anderen Höfen. Nachträge. Jahrbuch der Kunsthistorischen Sammlungen, Wien (14), 329–334.

Boeheim, W., 1895. Nürnberger Waffenschmiede und ihre Werke in den Kaiserlichen und anderen Sammlungen. Jahrbuch der Kunsthistorischen Sammlungen, Wien (16), 364– 401.

Boeheim, W., 1897-99. Ein gotischer Feldharnisch aus der Sammlung Windisch-Graetz. Zeitschrift für historische Waffen- und Kostümkunde (1), 210–221.

Boeheim, W., 2000. Handbuch der Waffenkunde: Das Waffenwesen in seiner historischen Entwickelung vom Beginn des Mittelalters bis zum Ende des 18. Jahrhunderts, Repr. ed., Holzminden.

Böhmer, J.F ., Wiesflecker, H. (Eds.), 1990-1996. Regesta Imperii 3, Wien, Köln.

Braun, K., 1866. Das Landwehr-Zeughaus in München, München.

Brepohl, E., 1987. Theophilus Presbyter und die mittelalterliche Goldschmiedekunst, Leipzig.

Brooker, R., 2007. Landeszeughaus Graz, Austria: Radschloss Sammlung/Wheellock collection, Graz.

Buchon, J.A.C., 1843. La Grèce continentale et la Morée: Voyage, séjour et études historiques en 1840 et 1841, Paris.

Buchwald, V .F., Wivel, H., 1998. Slag Analysis as a Method for the Characterization and Provenancing of Ancient Iron Objects. Materials Characterization (40), 73–96.

Buff, A., 1893. Geschichte der Augsburger Plattner der Renaissancezeit, Bamberg.

Calvert, A.F., 1907. Spanish arms and amour: Being a historical and descriptive account of the Royal Armoury of Madrid, London.

Capwell, T., 2002. A depiction of an Italian Arming Doublet. Zeitschrift für Waffen- und Kostümkunde (2), 177–196.

Charles, J.A., 1998. Development and use of layered ferrous microstructure. Material Science and Technology (14), 496–503.

Cook, A.C., Southon, J.R., Wadsworth, J., 2003. Using Radiocarbon Dating to Establish the Age of Iron-Based Artifacts. Journal of The Minerals, Metals & Materials Society 6 (4), 15–21.

Cosson, C.A. de, 1884. On gauntlets, London.

Craddock, P .T., 2009. Scientific investigation of copies, fakes and forgeries, Oxford, Burlington.

Cripps-Day, F.H., 1922. On armour preserved in English Churches, London.

Cripps-Day, F.H., 1925. A record of armour sales 1881 - 1924, London.

Dean, B., 1921. Buckles Which Belonged to Ancient Armor. Metropolitan Museum of Art bulletin, 60–62.

Dean, B., 1925. Early Gothic Armor. Metropolitan Museum of Art bulletin (20), 132–134.

Di Carpegna, N. (Ed.), 1969. Le armi Odescalchi, Rome.

Düriegl, G. (Ed.), 1977. Das Wiener Bürgerliche Zeughaus: Rüstungen u. Waffen aus 5 Jh; von d. Ländern Wien u. Niederösterreich gemeinsam veranstaltete Ausstellung im Schloss Schallaburg bei Melk; 49. Sonderausstellung d. Histor. Museums d. Stadt

Wien, 14. Mai - 30. Oktober 1977, Wien.

Eaves, I., 2002. Catalogue of European armour at the Fitzwilliam Museum, Woodbridge.

Edge, D., Williams, A., 2001. A study of the German "gothic" 15th-century equestrian armour (A21) in the Wallace Collection, London. Gladius (21), 233–256.

Egg, E., 1992. Die Innsbrucker Plattnerwerkstätten 1450 bis 1650, in: Opll, F . (Ed.), Stadt und Eisen. Beiträge zur Geschichte der Städte Mitteleuropas 11, Linz, pp. 311–325.

Espelund, A., 1996. Archäo-Metallurgie, von Norwegen aus betrachtet. Ferrum (68), 43– 52.

Ffoulkes, C., 1911. On Italian Armour from Chalcis in the Ethnological Museum at Athens: Based on photographs, notes and measurements made by Ramsay Traquair, Oxford.

Ffoulkes, C., 1912. The armourer and his craft, London.

Fingerlin, I., 1971. Gürtel des hohen und späten Mittelalters, München, Freiburg.

Frauenhofer, W., 2004. Das Handwerk der Plattner und Panzermacher in Landshut im 15. und 16. Jahrhundert. Ars Bavarica (87), 107–111.

Galea, M., Mintoff, M., 1990. Malta: The palace of the Grandmasters and the armoury, 2nd ed., Valletta.

Galerie Fischer (Ed.), 1934. Auktion: Waffensaal des Schlosses Grafenegg, Herzog Viktor von Ratibor: II. Teil, 2. Mai 1934, Luzern.

Galerie Fischer (Ed.), 1964. Waffenauktion 17. Juni 1964: Hervorragende Kampf- Turnier- und Prunkwaffen aus europäischem und amerikanischem Besitz, Luzern.

Gamber, O., 1953. Harnischstudien: V . Stilgeschichte des Plattenharnisches von den Anfängen bis um 1440. Jahrbuch der Kunsthistorischen Sammlungen, Wien (NF14 (50)), 53–59.

Gamber, O., 1955. Harnischstudien: VI. Stilgeschichte des Plattenharnisches von 1440- 1510. Jahrbuch der Kunsthistorischen Sammlungen, Wien (NF15 (51)), 31–102.

Gamber, O., 1957. Der Turnierharnisch zur Zeit König Maximilians I. und das Thunsche Skizzenbuch: Beschreibung und Rekonstruktion des Kodex. Jahrbuch der Kunsthistorischen Sammlungen, Wien (NF17 (53)), 3–70.

Gamber, O., 1977. Landesfürstliche Harnische im Wiener Bürgerlichen Zeughaus, in: Düriegl, G. (Ed.), Das Wiener Bürgerliche Zeughaus. Rüstungen u. Waffen aus 5 Jh; von d. Ländern Wien u. Niederösterreich gemeinsam veranstaltete Ausstellung im Schloss Schallaburg bei Melk; 49. Sonderausstellung d. Histor. Museums d. Stadt

Wien, 14. Mai - 30. Oktober 1977, Wien, pp. 39–44.

Gamber, O., Schulz, M., Blair, C.e.a., 1972-1996. Glossarium armorum: (11 booklets) German; English; Czech; Spanish; Italian; Russian; Polish; Danish; French; Dutch., Graz.

Gardner, J.S., 1898. Foreign armour in England, London.

Gimbel, K.G., 1904. Waffen- und Kunstsammlung Karl Gimbel, Baden-Baden, Berlin, 69 S.

Goll, M., 2009. Mit eiserner Faust: Der Freiburger "Faltenbündelhandschuh". Genese, Werkstatt und Technologie, Norderstedt.

Goll, M., Sensfelder, J., 2011. "Schuster bleib' bei deinen Leisten!": Zum Phänomen vergleichbarer Meistermarken an Produkten unterschiedlicher Handwerksgattungen. Jahrblatt der Interessengemeinschaft Historische Armbrust, 63–69.

Grancsay, S.V ., 1929. Notes on armour of the Greenwich School. Metropolitan Museum Studies (2, No. 1), 85–101.

Grancsay, S.V ., 1931. The mutual influence of costume and armor: A study of specimens in the Metropolitan Museum of Art. Metropolitan Museum Studies (3, No. 2), 194–208.

Grancsay, S.V ., 1932. An exhibition of forgeries. Metropolitan Museum of Art bulletin (27, No. 2), 46–48.

Grancsay, S.V ., 1950. The Interrelationships of Costume and Armor. Metropolitan Museum of Art bulletin (8, No. 6).

Grancsay, S.V ., 1952-53. A Modern Method of Repairing a Medieval Helmet. Journal of the Walter's Art Gallery (15/16), 64-71, 98.

Grancsay, S.V ., Kienbusch, C.O.v., 1933. The Bashford Dean Collection of arms and armor in the Metropolitan Museum of Art, Portland.

Grimm, J., definition of "Rinke", in: Grimm, J. (Ed.), Deutsches Wörterbuch von Jacob Grimm und Wilhelm Grimm, vol. 14, p. 1016.

Grönwald, H., 2010. Die unterlegene eiserne Faust: Statusrelevante Metallfunde von der mittelalterlichen Burg Cucagna. Zeitschrift für Archäologie des Mittelalters (38), 161– 206.

Gut, H., 1986. Blick zurück in die Vergangenheit rund um das Blech. Blech Rohre Profile (33), 466–486.

Gyngell, D.S.H., 1959. Armourers marks: Being a compilation of the known marks of armourers, swordsmiths, and gunsmiths, London.

Hayward, J.F., 1977. A note on a Vienna arms and armour faker. Zeitschrift für Waffen- und Kostümkunde (2), 78–82.

Hefner-Alteneck, J.H. von, 1854. Trachten des christlichen Mittelalters, Frankfurt a. M., Darmstadt.

Helfen, L., Baumbach, T., Mikulík, P .e.a., 2005. High-resolution three-dimensional imaging of flat objects by synchrotron-radiation computed laminography. Applied Physics Letters (86-071915). Helfen, L., Myagotin, A., Mikulík, P .e.a. On the implementation of computed laminography using synchrotron radiation. Review of Scientific Instruments (82- 063702).

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1883. Schroll, Wien.

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1884. Schroll, Wien.

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1889. Schroll, Wien.

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1890. Schroll, Wien.

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1891. Schroll, Wien.

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1892. Schroll, Wien.

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1893. Schroll, Wien.

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1895. Schroll, Wien.

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1899. Schroll, Wien.

Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1900. Schroll, Wien.

Johannsen, O., 1925. Biringuccios Pirotechnia. Ein Lehrbuch der chemisch- metallurgischen Technologie und des Artilleriewesens aus dem 16. Jahrhundert, Braunschweig.

Kalcher, A., 1895. Landshuter Waffenschmiede: Aus einem Vortrage: "Zum Landshuter Kunstgewerbe". Verhandlungen des Historischen Vereins für Niederbayern, 335–345.

Karcheski, W.J., Richardson, T., 2003. The Medieval Armour from Rhodes, Leeds.

Karsten, C.J.B., 1816. Handbuch der Eisenhüttenkunde, Halle.

Kastner, J., Salaberger, D., Grabner, M., 2007. Mikro-Röntgencomputertomografie: Eine zerstörungsfreie Methode für die Archäologie. Archäologie Österreichs (18/1), 60–65.

Koch, A., Oberndorff, L. von, Winkelmann, E. (Eds.), 1939. Regesten der Pfalzgrafen am Rhein: 1214 - 1508 2, Innsbruck.

Köstler, H.J., 2006. Technisch-metallurgische Entwicklungen der Eisenindustrie in der Neuzeit: Teil 2. Puddelverfahren - ein Stahlerzeugungsprozess der "Schweißeisen-Ära". Berg- und Hüttenmännische Monatshefte 151 (3), 137–141.

Kroener, D., 1988. Anton Konrad (1880-1938). Zeitschrift für Waffen- und Kostümkunde (2), 97-10.

Laking, G.F., 1903. A catalogue of the armour and arms in the Armoury of the Knights of St. John of Jerusalem: Now in the Palace Valletta Malta, London.

Laking, G.F., 1920. A record of European armour and arms through seven centuries 5 vol., London.

Lang, G., Synnatzschke, P ., Lietzmann, K.-D.e.a., 1988. Die Anfänge der Walzwerkstechnik im sächsischen Erzgebirge. Neue Hütte (10), 389–393.

Levkoff, M.L., Hearst, W.R., 2008. Hearst the collector, New York.

Luchner, L., 1958. Denkmal eines Renaissancefürsten: Versuch einer Rekonstruktion des Ambraser Museums von 1583, Wien.

Lueger, O., 1908. Lexikon der gesamten Technik und ihrer Hilfswissenschaften, (6) Stuttgart, Leipzig.

Mann, J.G., 1933. Notes on the armour worn in Spain from the tenth to the fifteenth century. Archaeologia, 285–305.

Mann, J.G., 1938. A Further Account of the Armour preserved in the Sanctuary of the Madonna delle Grazie near Mantua, Oxford.

Mann, J.G., 1942. Two fourteenth century gauntlets from Ripon Cathedral. Antiquaries Journal (22/2), 113-12.

Mann, J.G., 1962. European arms and armour 1, London.

Martin, P ., 1967. Waffen und Rüstungen von Karl dem Großen bis zu Ludwig XIV ., Frankfurt a. M.

Meißner, B., Doktor, A., 2001. Galvanoplastik - Geschichte einer Technik aus dem 19. Jahrhundert, in: Meißner, B., Doktor, A., Mach, M. (Eds.), Bronze- und Galvanoplastik. Geschichte, Materialanalyse, Restaurierung. Arbeitshefte der Landesämter für Denkmalpflege Sachsen und Sachsen-Anhalt 5, Dresden, pp. 127–137.

Mowbray, A.E., 1967. Arms and armor from the atelier of Ernst Schmidt, Munich: Catalogue, Providence.

Müller, D., 1999. Restaurierung eines ritterlichen Harnischs. Burgen und Schlösser (3), 161–166.

Müller-Hickler, H., 1932-34. Über die Funde aus der Burg Tannenberg. Zeitschrift für historische Waffen- und Kostümkunde NF 4 (13) Bd. 8., 175–181.

Museen der Stadt Landshut (Ed.), 2009. Ritterwelten im Spätmittelalter: Höfisch-ritterliche Kultur der Reichen Herzöge von Bayern-Landshut, Landshut.

Mutz, A., 1981. Blech stand am Anfang unserer Kultur. Blech Rohre Profile 28 (2), 596– 599.

Mutz, A., 1983. Geschmiedetes Blech als Glockenmaterial. Blech Rohre Profile 30 (12), 504–505.

Nickel, H., 1974. Ullstein-Waffenbuch: Eine kulturhistorische Waffenkunde mit Markenverzeichnis, Berlin, Frankfurt a. M., Wien.

Nickel, H., 2002. About Ailettes and Achselschilde. Zeitschrift für Waffen- und Kostümkunde (2), 197–211.

Norman, A.V .B., not dated. Armour from Chalcis: Unpublished manuscript preserved in the library of the Royal Armouries in Leeds.

Oppermann, G.A., 1863. Die Fabrication der Panzerplatten in England. Dinglers's Polytechnisches Journal 170, 431–435.

Overman, F., 1851. The manufacture of iron: In all its various branches … to which is added an essay on the manufacture of steel, 2nd ed., Philadelphia.

Pierre Bergé & associés (Ed.), 2011. Le Musée Fantastique de Karsten Klingbeil: Première vente, armes et armures anciennes /part I, antique arms and armour, Bruxelles.

Piersig, W., 1988. Abriß zur geschichtlichen Entwicklung der Eisen- und Stahlgewinnungsverfahren. Fertigungstechnik und Betrieb (38), 181–182.

Piersig, W., 1989. Historischer Abriß zur Entwicklung des Thomasverfahrens vor 110 Jahren und seine Bedeutung für die Stahlindustrie. Fertigungstechnik und Betrieb (39), 247–248.

Pigott, V .C., 1989. A Modern Reincarnation of Ancient Slags. Journal of The Minerals, Metals & Materials Society (April), 70–71.

Post, P ., 1936. Waffen- und kostümgeschichtliche Ausdeutung der Limburger Chronik. Zeitschrift für historische Waffen- und Kostümkunde (NF 5 Heft 8), 177–183.

Potier Echelles, O.d., 1901. Ein Besuch in der Werkstätte eines Falschers alter Waffen, Leipzig.

Potier Echelles, O.d., 1918-20. Das Ende der Waffensammlung des Fürsten Ernst Weriand zu Windisch-Graetz. Zeitschrift für historische Waffen- und Kostümkunde (8), 298-30.

Price, B.R., Edge, D., Williams, A., 2000. Techniques of medieval armour reproduction: The 14th century, Boulder.

Puype, J.P ., 2003. Der sog. Goldene Helm aus Delft: eine Galvano-Replik in Eisen. Zeitschrift für Waffen- und Kostümkunde (2), 161–166.

Pyhrr, S.W., 1989. European Armour from the Imperial Ottoman Arsenal. Metropolitan Museum Journal (24), 85–116.

Pyhrr, S.W., 2000. European helmets, 1450-1650: Treasures from the Reserve Collection, New York.

Pyhrr, S.W., 2006. A history of arms and armour conservation at the Metropolitan Museum., in: Smith, R.D. (Ed.), Make all sure. The conservation and restoration of arms and armour, Leeds, pp. 105–113.

Quintana Lacaci, G., 1987. Armería del Palacio Real de Madrid, Madrid.

Rachewiltz, S. (Ed.), 2004. Das Brigantinen-Symposium auf Schloß Tirol. Bauforschung auf Schloß Tirol 3, Meran.

Reitzenstein, A.v., 1942. Deutsche Harnische, in: Roselius, L. (Ed.), Deutsche Kunst. Meisterwerke der Baukunst, Malerei, Bildhauerkunst, Graphik und des Kunsthandwerks, vol. 8, Bremen, pp. 1–13.

Reitzenstein, A.v., 1955. Die Plattner von Augsburg. Augusta 955- 1955. Forschungen und Studien zur Kultur- und Wirtschaftsgeschichte Augsburgs, 265-27.

Reitzenstein, A.v., 1959. Die Ordnung der Nürnberger Plattner. Zeitschrift für Waffen- und Kostümkunde (2), 54–85.

Reitzenstein, A.v., 1964. Der Waffenschmied, München.

Reitzenstein, A.v., 1967. Die Nürnberger Plattner. Beiträge zur Wirtschaftsgeschichte von Nürnberg (2), 700–772.

Reitzenstein, A.v., 1969. Über die Anfänge des Waffensammelns. Zeitschrift für Waffen- und Kostümkunde (2), 69–73.

Ress, F.-M., 1967. Die Nürnberger Briefbücher als Quelle zur Geschichte des Handwerks der eisen- und metallverarbeitenden Gewerbe sowie der Sozial- und Wirtschaftsgeschichte. Beiträge zur Wirtschaftsgeschichte von Nürnberg (2), 800–882.

Reverseau, J.-P ., 1982. Musée de l'armée: Les armes et la vie, Paris, New York.

Richardson, E.P ., 1954. A selection from the William Randolph Hearst Collection of Arms and Armor in the Detroit Institute of Arts, Detroit, 35 S.

Rimer, G., Richardson, T., Cooper, J.P .D. (Eds.), 2009. Henry VIII: Arms and the man, 1509 - 2009; publ. to mark the exhibition Henry VIII: Dressed to Kill at The White

Tower, Tower of London 3 April 2009 - 17 January 2010, Leeds.

Rose, D., Endlicher, G., Mucke, A., 1990. The occurence of 'Iscorite' in Medieval iron slags. JHMS (24/1), 27–32.

Rossi, F., 1972. Armi e armaioli bresciani del '400, Brescia.

Rossi, F., Di Carpegna, N. (Eds.), 1969. Armi antiche dal Museo Civico L Marzoli, Brescia.

Scalini, M., 1984. Armamento difensivo trecentesco: Dalle collezioni Carrand e Ressman. Lo Specchio del Bargello 16, Firenze.

Scalini, M., 1996. Die Churburger Rüstkammer, Udine.

Schedelmann, H., 1948. Konrad Fecit: The story of a remarkable forger. The Conoisseur, 8-13; 106-109.

Schedelmann, H., 1963. Der Waffensammler Teil I. Zeitschrift für Waffen- und Kostümkunde (2), 99-10. Schedelmann, H., 1964a. Der Waffensammler Teil II. Zeitschrift für Waffen- und Kostümkunde (1), 50–55. Schedelmann, H., 1964b. Der Waffensammler Teil III. Zeitschrift für Waffen- und Kostümkunde (2), 112-11.

Schedelmann, H., 1965. Der Waffensammler Teil IV . Zeitschrift für Waffen- und Kostümkunde (2), 124-13.

Schedelmann, H., 1966. Der Waffensammler Teil V . Zeitschrift für Waffen- und Kostümkunde (1), 53–55.

Schöbel, J., Karpinski, J., 1985. Prunkwaffen: Waffen und Rüstungen aus dem Historischen Museum Dresden, 5th ed., Stuttgart.

Schöbel, J., Schaal, D., 1985. Historisches Museum: Staatliche Kunstsammlungen Dresden, 4th ed., Dresden.

Schönherr, D. von, 1900. David von Schönherrs gesammelte Schriften 1, Innsbruck.

Sensfelder, J., 2009. Armbruste in den Kunstsammlungen der Veste Coburg, Coburg.

Smith, R.D., 2004. Review: Williams, Alan R., The Kinght and the Blast Furnace. A History of the Metallurgy of Armour in the Middle Ages and Early Modern period. http://www.deremilitari.org/REVIEWS/williams_blast.htm. Accessed 3 March 2012.

Spalding, D., 1981. An unrecorded English helm of c.1370. JAAS (June), 6-9, pl. IV-X.

Sperl, G., 2001. Metalle und Zeit - eine oft vergessene Problematik. Zeitschrift für Metallkunde (92/1), 3–8.

Spitzlberger, G. (Ed.), 1975. Landshuter Plattnerkunst: Ein Überblick. mit Katalog der Ausstellung vom 14. Juni bis 20. Juli 1975 im Deutschen Saal der Stadtresidenz, Landshut.

Spitzlberger, G. (Ed.), 1985. Unvergängliche Harnischkunst: Beiträge zur historischen Waffenkunde; Festgabe zur Ausstellung "Rüstungen und Waffen aus Gotik und Renaissance" vom 23. Juni bis 14. Juli 1985 in der Stadtresidenz Landshut anläßlich der Veranstaltungen der "Landshuter Hochzeit 1475". Schriftenreihe "Aus Archiv und Museum" 1, Landshut.

Starley, D., 2004. Royal Armouries Analysis Record (February 25th): Artefact: War hat, recorded as a fake of a Flemish piece of about 1460, Leeds.

Starley, D., 2006. Only Skin deep: Residual surface coatings on arms and armour, in: Smith, R.D. (Ed.), Make all sure. The conservation and restoration of arms and armour, Leeds, pp. 1–5.

Strauch, P . (Ed.), 1986. Jansen Enikels Werke: Weltchronik, Fürstenbuch. Deutsche Chroniken 3, München.

Takács, I., 2006. Sigismundus Rex et Imperator: Kunst und Kultur zur Zeit Sigismunds von Luxemburg (1387-1437), Mainz a Rhein.

Terjanian, P ., 2001. Armour made in Basel: A Fifteenth-Century Sallet Attributed to Hans Blarer the Younger. Metropolitan Museum Journal (36), 155-15.

Terjanian, P ., 2009. The King and the armourers of Flanders, in: Rimer, G., Richardson, T.,

Cooper, J.P .D. (Eds.), Henry VIII. Arms and the man, 1509 - 2009; publ. to mark the exhibition Henry VIII: Dressed to Kill at The White Tower, Tower of London 3 April 2009 - 17 January 2010, Leeds, pp. 155–161.

Thomas, B., 1944. Deutsche Plattnerkunst, München.

Thomas, B., 1974. Die Innsbrucker Plattnerkunst: Ein Nachtrag. Jahrbuch der Kunsthistorischen Sammlungen, Wien (NF34 (70)), 179-22. Thomas, B., 1977a. Die Harnische und Blankwaffen von Brescia, in: Thomas, B. (Ed.), Gesammelte Schriften zur historischen Waffenkunde, Graz, pp. 387–400. Thomas, B. (Ed.), 1977b. Gesammelte Schriften zur historischen Waffenkunde, Graz. Thomas, B., 1977c. Nürnberger Plattnerkunst in Wien, in: Thomas, B. (Ed.), Gesammelte Schriften zur historischen Waffenkunde, Graz, pp. 1307–1320.

Thomas, B. (Ed.), 1981. Die Heldenrüstkammer (Armamentarium Heroicum) Erzherzog Ferdinands II. Auf Schloß Ambras bei Innsbruck: Faksimiledruck der lat. Ausg. des Kupferstich-Bildinventars von 1601 bzw. 1603, Osnabrück.

Thomas, B., Gamber, O. (Eds.), 1976. Katalog der Leibrüstkammer: I. Teil. Der Zeitraum von 500 bis 1530, Wien.

Thomas, B., Gamber, O., 1977. Die Mailänder Plattnerkunst, in: Thomas, B. (Ed.), Gesammelte Schriften zur historischen Waffenkunde, Graz, pp. 971–1098.

Thordeman, B., 1940. Armour from the battle of Wisby 1361. Arkeologiska monografier, Stockholm.

Tiroler Landesmuseum Ferdinandeum (Ed.), 1954. Die Innsbrucker Plattnerkunst: Katalog;

Kunstausstellung vom 26.6. - 30.9.1954, Innsbruck.

Trapp, O.G., 1926. Zur Entwicklung der "Armet-Helme". Zeitschrift für historische Waffen- und Kostümkunde (2), 25–29.

Trapp, O.G., 1995. Die Churburger Rüstkammer, Repr. ed., Udine.

Treitzsaurwein, M., 1775. Der Weiss Kunig, eine Erzehlung von den Thaten Kaiser Maximilian des Ersten, Wien.

Valencia Don Juan, J.B. de, 1898. Catalogo historico-descriptivo de la real armeria de Madrid, Madrid, 2 bd.

Vassilatos, N., 1934. Middelalderhjelmene fra Chalkis, in: The Danish Arms & Armour

Society (Ed.), Vaabenhistoriske aarbøger, 1999/44, pp. 132–144.

Verhoeven, J.D., 2007. Steel metallurgy for the non-metallurgist, Materials Park.

Volger, O., 1873. Ueber die neuesten Fortschritte in der Galvanoplastik, insbesondere der Eisengalvanoplastik. Dinglers's Polytechnisches Journal (209), 362–367. Wackernagel, R.H. (Ed.), 1982a. Das Münchener Zeughaus, München-Zürich. Wackernagel, R.H., 1982b. Zur Geschichte und Aufstellung der "Gemainen Statt Ristungen und Khriegswaffen" im Münchner Zeughaus, in: Wackernagel, R.H. (Ed.), Das Münchener Zeughaus, München-Zürich, pp. 10–40.

Waissenberger, R., 1977. Die Wehrhaften Bürger Wiens, in: Düriegl, G. (Ed.), Das Wiener Bürgerliche Zeughaus. Rüstungen u. Waffen aus 5 Jh; von d. Ländern Wien u. Niederösterreich gemeinsam veranstaltete Ausstellung im Schloss Schallaburg bei Melk; 49. Sonderausstellung d. Histor. Museums d. Stadt Wien, 14. Mai - 30. Oktober 1977, Wien, pp. 20–38.

Watts, K.N., 1989. 150 years ago: The Eglinton Tournament and the gothic revival, in: The 43rd London Arms Fair. The Ramada Inn (London West), Lillie Road, S.W.6, Friday &

Saturday, 22nd & 23rd September 1989, London, pp. 22–27.

Watts, K.N., 1992. Samuel Pratt and armour faking, in: Jones, M. (Ed.), Why fakes matter. Essays on problems of authenticity, London, pp. 100–110.

Wessel, H.e.a., 1995. Die Kunst des Schmiedens - sichtbar gemacht mit ZfP , in: 100 Jahre Röntgenstrahlen und die heutige Vielfalt industrieller ZfP-Praxis. Aachen, 22. - 24. Mai 1995. Berichtsband / Deutsche Gesellschaft für Zerstörungsfreie Prüfung Jahrestagung … zerstörungsfreie Materialprüfung 47, Berlin, pp. 511–516.

Wettendorfer, E., 1943-44. Ein Zeughaus Vokabular. Zeitschrift für historische Waffen- und Kostümkunde NF 8 (17) Heft 5/6, 74–77.

Willers, J., 1978. Nuremberg weapons and armour. Connoisseur (199), 173-17.

Williams, A.R., 1979. To what extent can forgeries be detected by metallurgical analysis? A study on some helmets. Institut suisse d'armes (Hg.) – Rapport (3+4), 61–78.

Williams, A.R., 1981. Four helms of the fourteenth century compared. JAAS (June), 80– 102.

Williams, A.R., 1991. Slag inclusions in armour. The Journal of the Historical Metallurgy Society (24/2), 69–80.

Williams, A.R., 2003. The Knight and the Blast Furnace: A history of the Metallurgy of Armour in the Middle Ages and the Early Modern Period, Leiden-Boston.

Williams, A., Reuck, A. de, 1995. The Royal Armoury at Greenwich, 1515-1649: A History of its Technology, London.

Redaktionelle Hinweise · 2
  • Bibliografische Titel, Namen, Erscheinungsjahre und Seitenangaben bleiben Quellenwerte, nicht neu recherchierte Angaben. Nur Zeilenumbrüche und eindeutige PDF-Abstände normalisiert.
  • Mehrere offenbar verkürzte Seitenbereiche (u. a. „97-10“, „113-12“, „155-15“) sowie widersprüchliche Datierungen sind vor Veröffentlichung anhand der zitierten Werke zu prüfen. Fehlende Stellen wurden nicht erraten.
Originalwortlaut vergleichen
References 



 



Agricola, G., 1977. V om Berg- und Hüttenwesen: Zwölf Bücher vom Berg- und 



Hüttenwesen, München. 



Anonymous, definition of "alloy", in: Encyclopaedia Britannica. 



Anonymous, 1930. Educational charts of arms and armor: Metropolitan Museum of Art, 



New York. 



Anonymous, 1983. Historisches aus der Geschichte der Blechfabrikation. Blech Rohre 



Profile 30 (3), 118–122. 



Anonymous, 1987. Über die Blechfabrikation um 1860 bis 1890. Blech Rohre Profile (5), 



401–403. 



Anonymous, 1828. Wie viel Nägel ein geschikter Nagelschmied in einer Woche ohne 



Maschine fertigen kann. Dinglers's Polytechnisches Journal (27), 464. 



Anonymous, 1880. Das Eisenhüttenwesen in Deutschland. Dinglers's Polytechnisches 



Journal (238), 77–88. 



Anstruther, I., 1963. The knight and the umbrella: An account of the Eglinton Tournament 



1839, London. 



Appelt, H. (Ed.), 1988. Terminologie und Typologie mittelalterlicher Sachgüter: Das 



Beispiel der Kleidung; internationales Round-Table-Gespräch, Krems an der Donau, 6. 



Oktober 1986. V eröffentlichungen des Instituts für Mittelalterliche Realienkunde 



Österreichs 10, Wien. 



Avinash C. Kak, M.S., 2001. Principles of Computerized Tomographic Imaging, 



Philadelphia. 



Bargel, H.-J., 2012. Werkstoffkunde, 11th ed., Berlin. 



Bartl, A. (Ed.), 2005. Der "Liber illuministarum" aus Kloster Tegernsee: Edition, 



Übersetzung und Kommentar der kunsttechnologischen Rezepte, Stuttgart. 



Bauer, S., Demmler, T., 1941. Deutsche Ritterdenkmäler in Römhild. Der eiserne Hammer 



61, Königstein im Taunus. 



Bäumel, J., 2004. The Dresden Armory, 2nd ed., München. 



Beabey, M., Richardson, T., 1997. Hardened leather armour. Royal Armouries yearbook, 



64–71. 



Berbenni, A., 1973. Encyclopaedia cinematographica: Central Europe - Lombardy. Forging 



of buckets for brickwork in a waterpowered hammer-mill., Göttingen. 



Berger, D., 2006. Steingussformen aus dem spätromanischen-frühgotischen Magdeburg: 



Archäometrische und experimentalarchäologische Untersuchungen zum 



mittelalterlichen Zinnguss an ausgewählten Fundstücken. Diplomarbeit, Freiberg. 



Blair, C., 1972. European armour: Circa 1066 to circa 1700, Repr. ed., London. 



Blair, C., 1983. Notes on Armour from Chalcis, in: The International arms & armour 



exposition. The Dorchester Hotel, 3-5 November 1983, London, pp. 7–14. 



Boccia, L.G., not dated. The Xalkis funds in Athens and New York.: Unpublished 



manuscript preserved in the library of the Royal Armouries in Leeds.



Boccia, L.G., 1982. Le armature di S. Maria delle Grazie di Curtatone di Mantova e 



l’armatura lombarda del ‘400, Bramante. 



Boccia, L.G., Coelho, E.T., 1967. L' arte dell'armatura in Italia, Milano. 



Boeheim, W., 1889. Werke Mailänder Waffenschmiede in den kaiserlichen Sammlungen. 



Jahrbuch der Kunsthistorischen Sammlungen, Wien (9), 375–418. 



Boeheim, W., 1891. Augsburger Waffenschmiede: Ihre Werke und ihre Beziehungen zum 



kaiserlichen Hof und zu anderen Höfen. Teil I. Jahrbuch der Kunsthistorischen 



Sammlungen, Wien (12), 165–201. 



Boeheim, W., 1892. Augsburger Waffenschmiede: Ihre Werke und ihre Beziehungen zum 



kaiserlichen Hof und zu anderen Höfen. Teil II. Jahrbuch der Kunsthistorischen 



Sammlungen, Wien (13), 202–222. 



Boeheim, W., 1893. Augsburger Waffenschmiede: Ihre Werke und ihre Beziehungen zum 



kaiserlichen Hof und zu anderen Höfen. Nachträge. Jahrbuch der Kunsthistorischen 



Sammlungen, Wien (14), 329–334. 



Boeheim, W., 1895. Nürnberger Waffenschmiede und ihre Werke in den Kaiserlichen und 



anderen Sammlungen. Jahrbuch der Kunsthistorischen Sammlungen, Wien (16), 364–



401. 



Boeheim, W., 1897-99. Ein gotischer Feldharnisch aus der Sammlung Windisch-Graetz. 



Zeitschrift für historische Waffen- und Kostümkunde (1), 210–221. 



Boeheim, W., 2000. Handbuch der Waffenkunde: Das Waffenwesen in seiner historischen 



Entwickelung vom Beginn des Mittelalters bis zum Ende des 18. Jahrhunderts, Repr. 



ed., Holzminden. 



Böhmer, J.F ., Wiesflecker, H. (Eds.), 1990-1996. Regesta Imperii 3, Wien, Köln. 



Braun, K., 1866. Das Landwehr-Zeughaus in München, München. 



Brepohl, E., 1987. Theophilus Presbyter und die mittelalterliche Goldschmiedekunst, 



Leipzig. 



Brooker, R., 2007. Landeszeughaus Graz, Austria: Radschloss Sammlung/Wheellock 



collection, Graz. 



Buchon, J.A.C., 1843. La Grèce continentale et la Morée: V oyage, séjour et études 



historiques en 1840 et 1841, Paris. 



Buchwald, V .F., Wivel, H., 1998. Slag Analysis as a Method for the Characterization and 



Provenancing of Ancient Iron Objects. Materials Characterization (40), 73–96. 



Buff, A., 1893. Geschichte der Augsburger Plattner der Renaissancezeit, Bamberg. 



Calvert, A.F., 1907. Spanish arms and amour: Being a historical and descriptive account of 



the Royal Armoury of Madrid, London. 



Capwell, T., 2002. A depiction of an Italian Arming Doublet. Zeitschrift für Waffen- und 



Kostümkunde (2), 177–196. 



Charles, J.A., 1998. Development and use of layered ferrous microstructure. Material 



Science and Technology (14), 496–503. 



Cook, A.C., Southon, J.R., Wadsworth, J., 2003. Using Radiocarbon Dating to Establish 



the Age of Iron-Based Artifacts. Journal of The Minerals, Metals & Materials Society 6 



(4), 15–21.



Cosson, C.A. de, 1884. On gauntlets, London. 



Craddock, P .T., 2009. Scientific investigation of copies, fakes and forgeries, Oxford, 



Burlington. 



Cripps-Day, F.H., 1922. On armour preserved in English Churches, London. 



Cripps-Day, F.H., 1925. A record of armour sales 1881 - 1924, London. 



Dean, B., 1921. Buckles Which Belonged to Ancient Armor. Metropolitan Museum of Art 



bulletin, 60–62. 



Dean, B., 1925. Early Gothic Armor. Metropolitan Museum of Art bulletin (20), 132–134. 



Di Carpegna, N. (Ed.), 1969. Le armi Odescalchi, Rome. 



Düriegl, G. (Ed.), 1977. Das Wiener Bürgerliche Zeughaus: Rüstungen u. Waffen aus 5 Jh; 



von d. Ländern Wien u. Niederösterreich gemeinsam veranstaltete Ausstellung im 



Schloss Schallaburg bei Melk; 49. Sonderausstellung d. Histor. Museums d. Stadt 



Wien, 14. Mai - 30. Oktober 1977, Wien. 



Eaves, I., 2002. Catalogue of European armour at the Fitzwilliam Museum, Woodbridge. 



Edge, D., Williams, A., 2001. A study of the German "gothic" 15th-century equestrian 



armour (A21) in the Wallace Collection, London. Gladius (21), 233–256. 



Egg, E., 1992. Die Innsbrucker Plattnerwerkstätten 1450 bis 1650, in: Opll, F . (Ed.), Stadt 



und Eisen. Beiträge zur Geschichte der Städte Mitteleuropas 11, Linz, pp. 311–325. 



Espelund, A., 1996. Archäo-Metallurgie, von Norwegen aus betrachtet. Ferrum (68), 43–



52. 



Ffoulkes, C., 1911. On Italian Armour from Chalcis in the Ethnological Museum at Athens: 



Based on photographs, notes and measurements made by Ramsay Traquair, Oxford. 



Ffoulkes, C., 1912. The armourer and his craft, London. 



Fingerlin, I., 1971. Gürtel des hohen und späten Mittelalters, München, Freiburg. 



Frauenhofer, W., 2004. Das Handwerk der Plattner und Panzermacher in Landshut im 15. 



und 16. Jahrhundert. Ars Bavarica (87), 107–111. 



Galea, M., Mintoff, M., 1990. Malta: The palace of the Grandmasters and the armoury, 2nd 



ed., V alletta. 



Galerie Fischer (Ed.), 1934. Auktion: Waffensaal des Schlosses Grafenegg, Herzog Viktor 



von Ratibor: II. Teil, 2. Mai 1934, Luzern. 



Galerie Fischer (Ed.), 1964. Waffenauktion 17. Juni 1964: Hervorragende Kampf- Turnier- 



und Prunkwaffen aus europäischem und amerikanischem Besitz, Luzern. 



Gamber, O., 1953. Harnischstudien: V . Stilgeschichte des Plattenharnisches von den 



Anfängen bis um 1440. Jahrbuch der Kunsthistorischen Sammlungen, Wien (NF14 



(50)), 53–59. 



Gamber, O., 1955. Harnischstudien: VI. Stilgeschichte des Plattenharnisches von 1440-



1510. Jahrbuch der Kunsthistorischen Sammlungen, Wien (NF15 (51)), 31–102. 



Gamber, O., 1957. Der Turnierharnisch zur Zeit König Maximilians I. und das Thunsche 



Skizzenbuch: Beschreibung und Rekonstruktion des Kodex. Jahrbuch der 



Kunsthistorischen Sammlungen, Wien (NF17 (53)), 3–70.



Gamber, O., 1977. Landesfürstliche Harnische im Wiener Bürgerlichen Zeughaus, 



in: Düriegl, G. (Ed.), Das Wiener Bürgerliche Zeughaus. Rüstungen u. Waffen aus 5 Jh; 



von d. Ländern Wien u. Niederösterreich gemeinsam veranstaltete Ausstellung im 



Schloss Schallaburg bei Melk; 49. Sonderausstellung d. Histor. Museums d. Stadt 



Wien, 14. Mai - 30. Oktober 1977, Wien, pp. 39–44. 



Gamber, O., Schulz, M., Blair, C.e.a., 1972-1996. Glossarium armorum: (11 booklets) 



German; English; Czech; Spanish; Italian; Russian; Polish; Danish; French; Dutch., 



Graz. 



Gardner, J.S., 1898. Foreign armour in England, London. 



Gimbel, K.G., 1904. Waffen- und Kunstsammlung Karl Gimbel, Baden-Baden, Berlin, 69 



S. 



Goll, M., 2009. Mit eiserner Faust: Der Freiburger "Faltenbündelhandschuh". Genese, 



Werkstatt und Technologie, Norderstedt. 



Goll, M., Sensfelder, J., 2011. "Schuster bleib' bei deinen Leisten!": Zum Phänomen 



vergleichbarer Meistermarken an Produkten unterschiedlicher Handwerksgattungen. 



Jahrblatt der Interessengemeinschaft Historische Armbrust, 63–69. 



Grancsay, S.V ., 1929. Notes on armour of the Greenwich School. Metropolitan Museum 



Studies (2, No. 1), 85–101. 



Grancsay, S.V ., 1931. The mutual influence of costume and armor: A study of specimens in 



the Metropolitan Museum of Art. Metropolitan Museum Studies (3, No. 2), 194–208. 



Grancsay, S.V ., 1932. An exhibition of forgeries. Metropolitan Museum of Art bulletin (27, 



No. 2), 46–48. 



Grancsay, S.V ., 1950. The Interrelationships of Costume and Armor. Metropolitan Museum 



of Art bulletin (8, No. 6). 



Grancsay, S.V ., 1952-53. A Modern Method of Repairing a Medieval Helmet. Journal of 



the Walter's Art Gallery (15/16), 64-71, 98. 



Grancsay, S.V ., Kienbusch, C.O.v., 1933. The Bashford Dean Collection of arms and armor 



in the Metropolitan Museum of Art, Portland. 



Grimm, J., definition of "Rinke", in: Grimm, J. (Ed.), Deutsches Wörterbuch von Jacob 



Grimm und Wilhelm Grimm, vol. 14, p. 1016. 



Grönwald, H., 2010. Die unterlegene eiserne Faust: Statusrelevante Metallfunde von der 



mittelalterlichen Burg Cucagna. Zeitschrift für Archäologie des Mittelalters (38), 161–



206. 



Gut, H., 1986. Blick zurück in die V ergangenheit rund um das Blech. Blech Rohre Profile 



(33), 466–486. 



Gyngell, D.S.H., 1959. Armourers marks: Being a compilation of the known marks of 



armourers, swordsmiths, and gunsmiths, London. 



Hayward, J.F., 1977. A note on a Vienna arms and armour faker. Zeitschrift für Waffen- 



und Kostümkunde (2), 78–82. 



Hefner-Alteneck, J.H. von, 1854. Trachten des christlichen Mittelalters, Frankfurt a. M., 



Darmstadt.



Helfen, L., Baumbach, T., Mikulík, P .e.a., 2005. High-resolution three-dimensional 



imaging of flat objects by synchrotron-radiation computed laminography. Applied 



Physics Letters (86-071915). 



Helfen, L., Myagotin, A., Mikulík, P .e.a. On the implementation of computed 



laminography using synchrotron radiation. Review of Scientific Instruments (82-



063702). 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1883. Schroll, Wien. 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1884. Schroll, Wien. 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1889. Schroll, Wien. 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1890. Schroll, Wien. 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1891. Schroll, Wien. 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1892. Schroll, Wien. 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1893. Schroll, Wien. 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1895. Schroll, Wien. 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1899. Schroll, Wien. 



Jahrbuch der Kunsthistorischen Sammlungen in Wien (Ed.), 1900. Schroll, Wien. 



Johannsen, O., 1925. Biringuccios Pirotechnia. Ein Lehrbuch der chemisch-



metallurgischen Technologie und des Artilleriewesens aus dem 16. Jahrhundert, 



Braunschweig. 



Kalcher, A., 1895. Landshuter Waffenschmiede: Aus einem V ortrage: "Zum Landshuter 



Kunstgewerbe". V erhandlungen des Historischen V ereins für Niederbayern, 335–345. 



Karcheski, W.J., Richardson, T., 2003. The Medieval Armour from Rhodes, Leeds. 



Karsten, C.J.B., 1816. Handbuch der Eisenhüttenkunde, Halle. 



Kastner, J., Salaberger, D., Grabner, M., 2007. Mikro-Röntgencomputertomografie: Eine 



zerstörungsfreie Methode für die Archäologie. Archäologie Österreichs (18/1), 60–65. 



Koch, A., Oberndorff, L. von, Winkelmann, E. (Eds.), 1939. Regesten der Pfalzgrafen am 



Rhein: 1214 - 1508 2, Innsbruck. 



Köstler, H.J., 2006. Technisch-metallurgische Entwicklungen der Eisenindustrie in der 



Neuzeit: Teil 2. Puddelverfahren - ein Stahlerzeugungsprozess der "Schweißeisen-Ära". 



Berg- und Hüttenmännische Monatshefte 151 (3), 137–141. 



Kroener, D., 1988. Anton Konrad (1880-1938). Zeitschrift für Waffen- und Kostümkunde 



(2), 97-10. 



Laking, G.F., 1903. A catalogue of the armour and arms in the Armoury of the Knights of 



St. John of Jerusalem: Now in the Palace V alletta Malta, London. 



Laking, G.F., 1920. A record of European armour and arms through seven centuries 5 vol., 



London. 



Lang, G., Synnatzschke, P ., Lietzmann, K.-D.e.a., 1988. Die Anfänge der 



Walzwerkstechnik im sächsischen Erzgebirge. Neue Hütte (10), 389–393. 



Levkoff, M.L., Hearst, W.R., 2008. Hearst the collector, New York. 



Luchner, L., 1958. Denkmal eines Renaissancefürsten: V ersuch einer Rekonstruktion des 



Ambraser Museums von 1583, Wien.



Lueger, O., 1908. Lexikon der gesamten Technik und ihrer Hilfswissenschaften, (6) 



Stuttgart, Leipzig. 



Mann, J.G., 1933. Notes on the armour worn in Spain from the tenth to the fifteenth 



century. Archaeologia, 285–305. 



Mann, J.G., 1938. A Further Account of the Armour preserved in the Sanctuary of the 



Madonna delle Grazie near Mantua, Oxford. 



Mann, J.G., 1942. Two fourteenth century gauntlets from Ripon Cathedral. Antiquaries 



Journal (22/2), 113-12. 



Mann, J.G., 1962. European arms and armour 1, London. 



Martin, P ., 1967. Waffen und Rüstungen von Karl dem Großen bis zu Ludwig XIV ., 



Frankfurt a. M. 



Meißner, B., Doktor, A., 2001. Galvanoplastik - Geschichte einer Technik aus dem 19. 



Jahrhundert, in: Meißner, B., Doktor, A., Mach, M. (Eds.), Bronze- und Galvanoplastik. 



Geschichte, Materialanalyse, Restaurierung. Arbeitshefte der Landesämter für 



Denkmalpflege Sachsen und Sachsen-Anhalt 5, Dresden, pp. 127–137. 



Mowbray, A.E., 1967. Arms and armor from the atelier of Ernst Schmidt, Munich: 



Catalogue, Providence. 



Müller, D., 1999. Restaurierung eines ritterlichen Harnischs. Burgen und Schlösser (3), 



161–166. 



Müller-Hickler, H., 1932-34. Über die Funde aus der Burg Tannenberg. Zeitschrift für 



historische Waffen- und Kostümkunde NF 4 (13) Bd. 8., 175–181. 



Museen der Stadt Landshut (Ed.), 2009. Ritterwelten im Spätmittelalter: Höfisch-ritterliche 



Kultur der Reichen Herzöge von Bayern-Landshut, Landshut. 



Mutz, A., 1981. Blech stand am Anfang unserer Kultur. Blech Rohre Profile 28 (2), 596–



599. 



Mutz, A., 1983. Geschmiedetes Blech als Glockenmaterial. Blech Rohre Profile 30 (12), 



504–505. 



Nickel, H., 1974. Ullstein-Waffenbuch: Eine kulturhistorische Waffenkunde mit 



Markenverzeichnis, Berlin, Frankfurt a. M., Wien. 



Nickel, H., 2002. About Ailettes and Achselschilde. Zeitschrift für Waffen- und 



Kostümkunde (2), 197–211. 



Norman, A.V .B., not dated. Armour from Chalcis: Unpublished manuscript preserved in 



the library of the Royal Armouries in Leeds. 



Oppermann, G.A., 1863. Die Fabrication der Panzerplatten in England. Dinglers's 



Polytechnisches Journal 170, 431–435. 



Overman, F., 1851. The manufacture of iron: In all its various branches … to which is 



added an essay on the manufacture of steel, 2nd ed., Philadelphia. 



Pierre Bergé & associés (Ed.), 2011. Le Musée Fantastique de Karsten Klingbeil: Première 



vente, armes et armures anciennes /part I, antique arms and armour, Bruxelles. 



Piersig, W., 1988. Abriß zur geschichtlichen Entwicklung der Eisen- und 



Stahlgewinnungsverfahren. Fertigungstechnik und Betrieb (38), 181–182.



Piersig, W., 1989. Historischer Abriß zur Entwicklung des Thomasverfahrens vor 110 



Jahren und seine Bedeutung für die Stahlindustrie. Fertigungstechnik und Betrieb (39), 



247–248. 



Pigott, V .C., 1989. A Modern Reincarnation of Ancient Slags. Journal of The Minerals, 



Metals & Materials Society (April), 70–71. 



Post, P ., 1936. Waffen- und kostümgeschichtliche Ausdeutung der Limburger Chronik. 



Zeitschrift für historische Waffen- und Kostümkunde (NF 5 Heft 8), 177–183. 



Potier Echelles, O.d., 1901. Ein Besuch in der Werkstätte eines Falschers alter Waffen, 



Leipzig. 



Potier Echelles, O.d., 1918-20. Das Ende der Waffensammlung des Fürsten Ernst Weriand 



zu Windisch-Graetz. Zeitschrift für historische Waffen- und Kostümkunde (8), 298-30. 



Price, B.R., Edge, D., Williams, A., 2000. Techniques of medieval armour reproduction: 



The 14th century, Boulder. 



Puype, J.P ., 2003. Der sog. Goldene Helm aus Delft: eine Galvano-Replik in Eisen. 



Zeitschrift für Waffen- und Kostümkunde (2), 161–166. 



Pyhrr, S.W., 1989. European Armour from the Imperial Ottoman Arsenal. Metropolitan 



Museum Journal (24), 85–116. 



Pyhrr, S.W., 2000. European helmets, 1450-1650: Treasures from the Reserve Collection, 



New York. 



Pyhrr, S.W., 2006. A history of arms and armour conservation at the Metropolitan 



Museum., in: Smith, R.D. (Ed.), Make all sure. The conservation and restoration of 



arms and armour, Leeds, pp. 105–113. 



Quintana Lacaci, G., 1987. Armería del Palacio Real de Madrid, Madrid. 



Rachewiltz, S. (Ed.), 2004. Das Brigantinen-Symposium auf Schloß Tirol. Bauforschung 



auf Schloß Tirol 3, Meran. 



Reitzenstein, A.v., 1942. Deutsche Harnische, in: Roselius, L. (Ed.), Deutsche Kunst. 



Meisterwerke der Baukunst, Malerei, Bildhauerkunst, Graphik und des 



Kunsthandwerks, vol. 8, Bremen, pp. 1–13. 



Reitzenstein, A.v., 1955. Die Plattner von Augsburg. Augusta 955- 1955. Forschungen und 



Studien zur Kultur- und Wirtschaftsgeschichte Augsburgs, 265-27. 



Reitzenstein, A.v., 1959. Die Ordnung der Nürnberger Plattner. Zeitschrift für Waffen- und 



Kostümkunde (2), 54–85. 



Reitzenstein, A.v., 1964. Der Waffenschmied, München. 



Reitzenstein, A.v., 1967. Die Nürnberger Plattner. Beiträge zur Wirtschaftsgeschichte von 



Nürnberg (2), 700–772. 



Reitzenstein, A.v., 1969. Über die Anfänge des Waffensammelns. Zeitschrift für Waffen- 



und Kostümkunde (2), 69–73. 



Ress, F.-M., 1967. Die Nürnberger Briefbücher als Quelle zur Geschichte des Handwerks 



der eisen- und metallverarbeitenden Gewerbe sowie der Sozial- und 



Wirtschaftsgeschichte. Beiträge zur Wirtschaftsgeschichte von Nürnberg (2), 800–882. 



Reverseau, J.-P ., 1982. Musée de l'armée: Les armes et la vie, Paris, New York.



Richardson, E.P ., 1954. A selection from the William Randolph Hearst Collection of Arms 



and Armor in the Detroit Institute of Arts, Detroit, 35 S. 



Rimer, G., Richardson, T., Cooper, J.P .D. (Eds.), 2009. Henry VIII: Arms and the man, 



1509 - 2009; publ. to mark the exhibition Henry VIII: Dressed to Kill at The White 



Tower, Tower of London 3 April 2009 - 17 January 2010, Leeds. 



Rose, D., Endlicher, G., Mucke, A., 1990. The occurence of 'Iscorite' in Medieval iron 



slags. JHMS (24/1), 27–32. 



Rossi, F., 1972. Armi e armaioli bresciani del '400, Brescia. 



Rossi, F., Di Carpegna, N. (Eds.), 1969. Armi antiche dal Museo Civico L Marzoli, 



Brescia. 



Scalini, M., 1984. Armamento difensivo trecentesco: Dalle collezioni Carrand e Ressman. 



Lo Specchio del Bargello 16, Firenze. 



Scalini, M., 1996. Die Churburger Rüstkammer, Udine. 



Schedelmann, H., 1948. Konrad Fecit: The story of a remarkable forger. The Conoisseur, 



8-13; 106-109. 



Schedelmann, H., 1963. Der Waffensammler Teil I. Zeitschrift für Waffen- und 



Kostümkunde (2), 99-10. 



Schedelmann, H., 1964a. Der Waffensammler Teil II. Zeitschrift für Waffen- und 



Kostümkunde (1), 50–55. 



Schedelmann, H., 1964b. Der Waffensammler Teil III. Zeitschrift für Waffen- und 



Kostümkunde (2), 112-11. 



Schedelmann, H., 1965. Der Waffensammler Teil IV . Zeitschrift für Waffen- und 



Kostümkunde (2), 124-13. 



Schedelmann, H., 1966. Der Waffensammler Teil V . Zeitschrift für Waffen- und 



Kostümkunde (1), 53–55. 



Schöbel, J., Karpinski, J., 1985. Prunkwaffen: Waffen und Rüstungen aus dem 



Historischen Museum Dresden, 5th ed., Stuttgart. 



Schöbel, J., Schaal, D., 1985. Historisches Museum: Staatliche Kunstsammlungen 



Dresden, 4th ed., Dresden. 



Schönherr, D. von, 1900. David von Schönherrs gesammelte Schriften 1, Innsbruck. 



Sensfelder, J., 2009. Armbruste in den Kunstsammlungen der V este Coburg, Coburg. 



Smith, R.D., 2004. Review: Williams, Alan R., The Kinght and the Blast Furnace. A 



History of the Metallurgy of Armour in the Middle Ages and Early Modern period. 



http://www.deremilitari.org/REVIEWS/williams_blast.htm. Accessed 3 March 2012. 



Spalding, D., 1981. An unrecorded English helm of c.1370. JAAS (June), 6-9, pl. IV-X. 



Sperl, G., 2001. Metalle und Zeit - eine oft vergessene Problematik. Zeitschrift für 



Metallkunde (92/1), 3–8. 



Spitzlberger, G. (Ed.), 1975. Landshuter Plattnerkunst: Ein Überblick. mit Katalog der 



Ausstellung vom 14. Juni bis 20. Juli 1975 im Deutschen Saal der Stadtresidenz, 



Landshut. 



Spitzlberger, G. (Ed.), 1985. Unvergängliche Harnischkunst: Beiträge zur historischen 



Waffenkunde; Festgabe zur Ausstellung "Rüstungen und Waffen aus Gotik und



Renaissance" vom 23. Juni bis 14. Juli 1985 in der Stadtresidenz Landshut anläßlich 



der V eranstaltungen der "Landshuter Hochzeit 1475". Schriftenreihe "Aus Archiv und 



Museum" 1, Landshut. 



Starley, D., 2004. Royal Armouries Analysis Record (February 25th): Artefact: War hat, 



recorded as a fake of a Flemish piece of about 1460, Leeds. 



Starley, D., 2006. Only Skin deep: Residual surface coatings on arms and armour, 



in: Smith, R.D. (Ed.), Make all sure. The conservation and restoration of arms and 



armour, Leeds, pp. 1–5. 



Strauch, P . (Ed.), 1986. Jansen Enikels Werke: Weltchronik, Fürstenbuch. Deutsche 



Chroniken 3, München. 



Takács, I., 2006. Sigismundus Rex et Imperator: Kunst und Kultur zur Zeit Sigismunds 



von Luxemburg (1387-1437), Mainz a Rhein. 



Terjanian, P ., 2001. Armour made in Basel: A Fifteenth-Century Sallet Attributed to Hans 



Blarer the Younger. Metropolitan Museum Journal (36), 155-15. 



Terjanian, P ., 2009. The King and the armourers of Flanders, in: Rimer, G., Richardson, T., 



Cooper, J.P .D. (Eds.), Henry VIII. Arms and the man, 1509 - 2009; publ. to mark the 



exhibition Henry VIII: Dressed to Kill at The White Tower, Tower of London 3 April 



2009 - 17 January 2010, Leeds, pp. 155–161. 



Thomas, B., 1944. Deutsche Plattnerkunst, München. 



Thomas, B., 1974. Die Innsbrucker Plattnerkunst: Ein Nachtrag. Jahrbuch der 



Kunsthistorischen Sammlungen, Wien (NF34 (70)), 179-22. 



Thomas, B., 1977a. Die Harnische und Blankwaffen von Brescia, in: Thomas, B. (Ed.), 



Gesammelte Schriften zur historischen Waffenkunde, Graz, pp. 387–400. 



Thomas, B. (Ed.), 1977b. Gesammelte Schriften zur historischen Waffenkunde, Graz. 



Thomas, B., 1977c. Nürnberger Plattnerkunst in Wien, in: Thomas, B. (Ed.), Gesammelte 



Schriften zur historischen Waffenkunde, Graz, pp. 1307–1320. 



Thomas, B. (Ed.), 1981. Die Heldenrüstkammer (Armamentarium Heroicum) Erzherzog 



Ferdinands II. Auf Schloß Ambras bei Innsbruck: Faksimiledruck der lat. Ausg. des 



Kupferstich-Bildinventars von 1601 bzw. 1603, Osnabrück. 



Thomas, B., Gamber, O. (Eds.), 1976. Katalog der Leibrüstkammer: I. Teil. Der Zeitraum 



von 500 bis 1530, Wien. 



Thomas, B., Gamber, O., 1977. Die Mailänder Plattnerkunst, in: Thomas, B. (Ed.), 



Gesammelte Schriften zur historischen Waffenkunde, Graz, pp. 971–1098. 



Thordeman, B., 1940. Armour from the battle of Wisby 1361. Arkeologiska monografier, 



Stockholm. 



Tiroler Landesmuseum Ferdinandeum (Ed.), 1954. Die Innsbrucker Plattnerkunst: Katalog; 



Kunstausstellung vom 26.6. - 30.9.1954, Innsbruck. 



Trapp, O.G., 1926. Zur Entwicklung der "Armet-Helme". Zeitschrift für historische 



Waffen- und Kostümkunde (2), 25–29. 



Trapp, O.G., 1995. Die Churburger Rüstkammer, Repr. ed., Udine. 



Treitzsaurwein, M., 1775. Der Weiss Kunig, eine Erzehlung von den Thaten Kaiser 



Maximilian des Ersten, Wien.



V alencia Don Juan, J.B. de, 1898. Catalogo historico-descriptivo de la real armeria de 



Madrid, Madrid, 2 bd. 



V assilatos, N., 1934. Middelalderhjelmene fra Chalkis, in: The Danish Arms & Armour 



Society (Ed.), V aabenhistoriske aarbøger, 1999/44, pp. 132–144. 



V erhoeven, J.D., 2007. Steel metallurgy for the non-metallurgist, Materials Park. 



V olger, O., 1873. Ueber die neuesten Fortschritte in der Galvanoplastik, insbesondere der 



Eisengalvanoplastik. Dinglers's Polytechnisches Journal (209), 362–367. 



Wackernagel, R.H. (Ed.), 1982a. Das Münchener Zeughaus, München-Zürich. 



Wackernagel, R.H., 1982b. Zur Geschichte und Aufstellung der "Gemainen Statt Ristungen 



und Khriegswaffen" im Münchner Zeughaus, in: Wackernagel, R.H. (Ed.), Das 



Münchener Zeughaus, München-Zürich, pp. 10–40. 



Waissenberger, R., 1977. Die Wehrhaften Bürger Wiens, in: Düriegl, G. (Ed.), Das Wiener 



Bürgerliche Zeughaus. Rüstungen u. Waffen aus 5 Jh; von d. Ländern Wien u. 



Niederösterreich gemeinsam veranstaltete Ausstellung im Schloss Schallaburg bei 



Melk; 49. Sonderausstellung d. Histor. Museums d. Stadt Wien, 14. Mai - 30. Oktober 



1977, Wien, pp. 20–38. 



Watts, K.N., 1989. 150 years ago: The Eglinton Tournament and the gothic revival, in: The 



43rd London Arms Fair. The Ramada Inn (London West), Lillie Road, S.W.6, Friday & 



Saturday, 22nd & 23rd September 1989, London, pp. 22–27. 



Watts, K.N., 1992. Samuel Pratt and armour faking, in: Jones, M. (Ed.), Why fakes matter. 



Essays on problems of authenticity, London, pp. 100–110. 



Wessel, H.e.a., 1995. Die Kunst des Schmiedens - sichtbar gemacht mit ZfP , in: 100 Jahre 



Röntgenstrahlen und die heutige Vielfalt industrieller ZfP-Praxis. Aachen, 22. - 24. Mai 



1995. Berichtsband / Deutsche Gesellschaft für Zerstörungsfreie Prüfung Jahrestagung 



… zerstörungsfreie Materialprüfung 47, Berlin, pp. 511–516. 



Wettendorfer, E., 1943-44. Ein Zeughaus V okabular. Zeitschrift für historische Waffen- und 



Kostümkunde NF 8 (17) Heft 5/6, 74–77. 



Willers, J., 1978. Nuremberg weapons and armour. Connoisseur (199), 173-17. 



Williams, A.R., 1979. To what extent can forgeries be detected by metallurgical analysis? A 



study on some helmets. Institut suisse d'armes (Hg.) – Rapport (3+4), 61–78. 



Williams, A.R., 1981. Four helms of the fourteenth century compared. JAAS (June), 80–



102. 



Williams, A.R., 1991. Slag inclusions in armour. The Journal of the Historical Metallurgy 



Society (24/2), 69–80. 



Williams, A.R., 2003. The Knight and the Blast Furnace: A history of the Metallurgy of 



Armour in the Middle Ages and the Early Modern Period, Leiden-Boston. 



Williams, A., Reuck, A. de, 1995. The Royal Armoury at Greenwich, 1515-1649: A History 



of its Technology, London.

Notes

Quellenangaben und historische Zitate bleiben erhalten. Redaktionelle Hinweise stehen beim jeweiligen Abschnitt.

1. For the published version of this thesis, see Goll (2009).

2. Ffoulkes (1912).

3. Price et al. (2000).

4. Most of the results are presented together in Williams (2003).

5. For example, Thomas and Gamber (1976), pp. 25–34.

6. In this study, an arsenal is a facility storing military equipment for large numbers of soldiers. Its stock could be issued rapidly to personnel or citizens in times of danger or war.

7. Objects are counted separately by the body area protected. Thus an articulated arm defence comprising upper-arm, elbow and forearm plates counts as three objects, while an isolated visor counts as one helmet record. I examined and photographed about 1,300 of these objects at high resolution.

8. See for example: Anonymous (1930), pl. 2.

9. Gamber et al. (1972-1996).

10. Boccia and Coelho (1967); Boccia (1982).

11. Rossi (1972); Thomas (1977a).

12. Boeheim (1889); Thomas and Gamber (1977).

13. Thomas (1944); Reitzenstein (1942).

14. Tiroler Landesmuseum Ferdinandeum (1954); Thomas (1974); Egg (1992).

15. Boeheim (1895); Reitzenstein (1967); Thomas (1977c); Willers (1978).

16. Frauenhofer (2004); Kalcher (1895); Spitzlberger (1975); Spitzlberger (1985).

17. Boeheim (1891); Boeheim (1892); Boeheim (1893); Buff (1893); Reitzenstein (1955).

18. Ffoulkes (1912), p. 136-137; Thomas and Gamber (1976), p. 195.

19. Terjanian (2009).

20. Calvert (1907); Mann (1933).

21. Grancsay (1929); Williams and Reuck (1995).

22. In the late Middle Ages and early Renaissance, “Rüstung” could denote a type of crossbow; see Sensfelder (2009). It also referred to winches, probably explaining its use for crossbows spanned by a winch. Its later application to armour remains unclear. I thank Jens Sensfelder for this information.

23. Terjanian (2001) p. 158.

24. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1895), Reg. 12675.

25. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1895), Reg. 13542.

26. See also the various essays (e. g. Janitz, Schuppert, Wilckens) on the problem of medieval terminology and typology in: Appelt (1988).

27. For the English translation the author of this paper has chosen the terms commonly used in English literature.

28. Transcribed from: Statthaltereiarchiv Innsbruck, Miscellanea 92 by: Schönherr (1900), p.79-680.

29. The Limburger Chronik uses “hundeskogeln” in 1389 in a context also listing breastplates and leg armour. This supports interpreting the word as a helmet, without establishing that every wearer had a complete ensemble. The passage apparently includes citizens and infantry as well as knights; see Post (1936), p. 179.

30. See for example: Schönherr (1900), p.79-680.

31. Inventories record two “tschelern” or “tschaelaern” in 1425 and three “tscheleden” in 1426; see Jahrbuch der Kunsthistorischen Sammlungen in Wien (1899), Reg. 17568 and 17573. Their German pronunciation resembles Italian “celata” more closely than “Schale” (bowl), often proposed as the German term’s root.

32. Blair cites sixteenth-century French, English and Spanish sources using the term for an open-faced helmet with a forehead peak and short flared nape guard: Blair (1972), p. 136.

33. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1900), Reg. 18319.

34. Ffoulkes (1911), p. 383.

35. Müller-Hickler (1932-34), p. 179.

36. To keep references concise, individual objects are identified below by their record IDs.

37. The source identifies no neck defence made from small plates secured to a textile or leather covering.

38. See e. g.: Statthaltereiarchiv Innsbruck, Miscellanea 92, edited in: Schönherr (1900), p.79-680.

39. See e. g.: Statthaltereiarchiv Innsbruck, Miscellanea 92, edited in: Schönherr (1900), p.79-680.

40. Compare also the arm defenses acc. no. A79 in the HJRK.

41. Type II is omitted because no examples survive in the classification. Type III retains its number for the fully enclosing form, by analogy with lower-leg protection.

42. Both “helmet” and “head defence” or “head protection” are used below, following common English usage.

43. For illustrative explanations on the development of all medieval helmet types see the chart in: Nickel (1974), p. 118.

44. Ffoulkes (1911), p. 383.

45. This is also the historical term, see: Strauch (1986), p.185.

46. Post (1936), p. 179.

47. For a comprehensive discussion on the development of this helmet-type see: Trapp (1926).

48. An exception is [ref_arm_4487] PDF, whose missing face guard was probably attached by staple and pin; see also Trapp (1926), p. 28.

49. The narrowing skull and rounded, flared nape guard place this helmet in Type V. Studies extending beyond 1500 may require a further category for “closed helmets”, perhaps Type IX.

50. See Henry VIII.’s foot-combat armour acc. no. II.6 in the RA.

51. See Henry VIII.’s foot-combat armour acc. no. II.6 in the RA.

52. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1883), Reg. 48.

53. This offline version of the database contains many objects beyond those cited in the text, allowing readers to make further comparisons.

54. Boeheim (2000), of course old, but still very useful for a general overview.

55. Gamber (1953) and Gamber (1955).

56. Blair (1972).

57. “Iron” and “steel” require care. Modern terminology includes forgeable iron alloys with up to about 2% carbon under steel, distinguishing higher-carbon cast iron; see Bargel (2012), p. 141. Historic usage commonly distinguished hardenable steel from softer iron. The source uses about 0.4% carbon as an approximate threshold, although hardenability is not governed by one universal boundary. Material quality cannot be established confidently without examination. Some armour is hardened or hardenable; other objects use softer iron. Earlier humanities scholarship sometimes applies these terms without testing or considering historic usage. This study therefore uses “iron or steel” where quality is unknown, and the terms separately when a particular material quality is intended.

58. This is for the arm: shoulder, upper arm, elbow and lower arm; for the leg: upper leg, knee, lower leg and foot.

59. This is different possible wearing-combinations of torso front and -back types.

60. Between about 1270 and 1350, chiefly in France, small shoulder-mounted shields known as “ailettes” or “Achselschilde” appear [ref_ill_art_5189] PDF. Their purpose is uncertain and a protective role disputed; see Nickel (2002). They are therefore excluded from the defensive classification here.

61. For reconstruction of leather hardening and a historical survey of leather armour, see Beabey and Richardson (1997).

62. See Burkhard von Seckendorf’s effigy (d. 1365), Heilig Geist Kirche, Gunzenhausen. I thank Christopher Retsch for this reference.

63. Blair (1972).

64. For details see chapter [Turning via sliding rivets [ref_ill_joi_turningviaslidingrivets]].

65. Cosson (1884), Mann (1942), Goll (2009).

66. For a discussion of several segmented hand-protections found in Wisby see: Thordeman (1940).

67. All organic components are lost, so the original arrangement of the finger plates remains uncertain.

68. This finger type is most likely genuine due to the old provenance of all quoted items.

69. The fingers are entirely reproductions.

70. Blair (1972), p. 47.

71. The supposed sight slit is too high to function. It may instead be damage from a sword or staff weapon.

72. The British and the Canadian army used a steel-helmet of type-III (MKI and MKII) from 1915 to 1945.

73. A second one is attached to the type-I helmet [ref_arm_2093] PDF.

74. The visor and the collar are lost.

75. Trapp (1926).

76. Blair (1972), p. 39.

77. The shell-like extension also permits a less likely interpretation as a late fourteenth-century Type II elbow defence with upper-arm protection. If so, it would be the only example with a medial elbow ridge.

78. Blair (1972), p. 39.

79. The painted figure wears metal strips on the outside of the lower legs, resembling arm-defence “jack chains”.

80. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1883), Reg. 48.

81. Blair (1972), p. 37.

82. It is possible that the badly damaged item [ref_arm_5127] PDF also was similarly box-shaped.

83. I found the upper-leg lames detached in a box; an older image shows them attached [ref_ill_art_5396] PDF. Another photograph [ref_ill_art_5395] PDF records comparable plates now missing from breastplate [ref_arm_3668] PDF. At the time of this study, they were thought likely to remain among recently relocated museum holdings awaiting unpacking.

84. Dean (1921), p. 60.

85. A relatively recent example is the use of black-and-white illustrations in Eaves (2002).

86. Other developments have also helped, including the relatively low cost of travel at the time of writing.

87. On authenticity, see Chapter 6, “The problem of authenticity”.

88. The bars around the arm openings are missing. Their former presence is indicated by holes, now occupied by rivets, that otherwise have no function.

89. For a discussion of the interrelationship between contemporary costume and armour see for example: Grancsay (1931) and Grancsay (1950).

90. Thomas (1977b), p. 626.

91. See discussion below in chapter [New recognitions on marks] and [A suit in the BMA].

92. Hammer scale is iron oxide formed on iron or steel heated to red heat or above in air. The source gives the reaction 3 Fe + 2 O₂ → Fe₃O₄.

93. See: Jahrbuch der Kunsthistorischen Sammlungen in Wien (1896), Reg. 15325. Translation by the author: […] two iron-hats, black and white […] but with the exception the best iron-hat for my wife […], it should stay for my housewife in the house […].

94. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 1010: „[…] unz zum hertnen und ausfeilen 12 Krebsen […]“. Translation by the author: […] until the hardening and the filing 12 breastplates […].

95. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1900), Reg. 18749.

96. See: Thomas and Gamber (1976), p. 27.

97. Thomas and Gamber (1976), p. 104, pl. 32-33.

98. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1899), Reg. 17646. Translation by the author: […] 19 ducaten to the armourer; the silver on the plates cost five markh; and three gulden from one mark cost the gilding; and two gulden of the mark as salary […].

99. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1899), Reg. 17774. Translation by the author: For the gilding of the armour for Scotland I have paid 10 ducaten and 4 r. gulden in the presence of the goldsmith Fuchs Micheln.

100. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1899), Reg. 17896. Translation by the author, retained from the dissertation: “1465 Juli 10. On behalf of my Lord I have given 6 ducaten to the Hofmeister Hainrichen von Freyberg to have gilded the armour of the young emperor.”

101. The irregular lines on suit [ref_arm_4143] PDF, to which this neck defence belongs, may be etched. If so, they would represent an early example of armour etching.

102. Kastner et al. (2007).

103. Museen der Stadt Landshut (2009) illustrates several helmets with rivet rows along the edges; figures 33 and 63 include sixth-century BC examples.

104. See for example the 1544 billing of expenses of Henry VIII.’s Royal Armouries in: Ffoulkes (1912), p. 183.

105. Seventeenth-century arsenal inventories and bills use “Krebs-Nögl” and “Harnisch Nögel”: Wettendorfer (1943–44), p. 75. The court armourer Konrad Seusenhofer likewise refers to “nagl” in 1511: Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 1028. A document of 1499 suggests that the term already denoted rivets in the fifteenth century. Maximilian I permits the transport of “eysen, stachl [steel] vnnd allerlay nagl” to Innsbruck for his needs: Böhmer and Wiesflecker (1990–1996), Reg. 13436 (http://regesten.regesta-imperii.de/index.php?uri=1499-06-19_4_0_14_3_2_640_13436). These supplies most probably served the armour workshops at Mühlau near Innsbruck; on this interpretation, the nails were rivets for attaching fittings.

106. Knee defences [ref_arm_2678] PDF [ref_arm_2846] PDF are exceptions: their sliding plate joints use Type a rivets. The legs have been extensively repaired, so these rivets may be replacements. The upper thigh lames use Type b rivets, as usual for those joints.

107. Pyhrr (2006), here p. 109-111.

108. Scalini (1996), p. 67 (German text).

109. Rossi and Di Carpegna also observed the similar helmet rivets and proposed a modern date: Rossi and Di Carpegna (1969), p. 39.

110. Wackernagel (1982a), p. 25, f).

111. Wackernagel collaborated with Mario Scalini on the Munich Zeughaus catalogue and probably obtained this suggestion from him. Scalini says that the “a bozzetta” rivets of the Munich breastplates “are not very different from certain original rivets on parts of armour that is certainly Italian and from more or less the same date.” As a comparable example for an Italian breastplate with a similar rivet he names an example from the Santuario della Madonna delle Grazie di Curtatone near Mantua. It is not clear where this item is stored now and no image is included in Scalini’s catalogue. Nevertheless, he is more careful than Wackernagel in drawing conclusions on a close relationship between the Churburg’s Brescian breastplates and those in Munich when he quotes: “This fact [the Italian-style rivets] unfortunately, cannot be considered to have probative force on the Munich breastplates being of Brescian origin since the sources, especially the Datini archive of Prato, speak of a massive trade in these tiny products, which were evidently put on the market by Lombard workshops at extremely competitive prices, if it was thought worthwhile to transport rivets to Avignon. Tuscany and elsewhere. Apart from possible later interventions, intended to improve pieces for museum purposes, one has to note how these rivets appear also on German pieces, and that there are notable differences between the Churburg and the Munich breastplates.”, for all quotes see: Scalini (1996), p. 71. I could find no breastplate outside the Munich group with a similarly decorated central rivet.

112. Wackernagel (1982a), p. 115.

113. Pyhrr (2000), p. 9, cat. no. 7.

114. [ref_arm_1900] PDF [ref_arm_1773] PDF [ref_arm_1742] PDF [ref_arm_1660] PDF [ref_arm_1686] PDF [ref_arm_1701] PDF [ref_arm_1707] PDF [ref_arm_1725] PDF [ref_arm_1797] PDF [ref_arm_1821] PDF [ref_arm_1826] PDF [ref_arm_1832] PDF [ref_arm_1837] PDF [ref_arm_1857] PDF [ref_arm_1865] PDF [ref_arm_1898] PDF [ref_arm_1899] PDF [ref_arm_4290] PDF [ref_arm_4397] PDF.

115. See discussion below in chapter [New recognitions on marks] and [A suit in the BMA].

116. Ffoulkes (1912), here p.183.

117. This is particularly surprising given the nineteenth-century demand for rivets in boilers, metal-framed buildings and ships.

118. See: Anonymus (1828).

119. Lueger (1908), here p.570-571. Translated by the author.

120. I experimented with making such rivets; see Goll (2009), pp. 02–103 [page range as printed; to be checked]. That method was rather cumbersome because I was not yet aware of the etching technique.

121. “Old” does not necessarily mean original to the object: a rivet may be a much later replacement made by traditional methods.

122. In the axonometric view of [ref_arm_1075] PDF, a loose rivet on the right exposes its shank and diameter. Note also the varying head diameters.

123. The restorer Ian Ashdown in Onnens (CH) uses such rivets.

124. Starley (2006), p. 4.

125. Starley gives copper-to-zinc ratios of 8:3 for modern brass and 7:3 for material predating a new zinc-production method introduced in 1743: Starley (2006), pp. 3–5. These are source-specific comparisons, not universal compositions for all brass.

126. The copper-alloy examples on [ref_arm_1398] PDF [ref_arm_1692] PDF may be solid castings; closer examination was not possible.

127. Again with the exception of [ref_arm_1398] PDF and [ref_arm_1692] PDF.

128. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 1028, also indicates that inexpensive infantry buckles were purchased rather than made by the armourers. For the obsolete terms “rincken” or “rinken”, see http://www.woerterbuchnetz.de/DWB?lemma=rinke (16 March 2012).

129. Dean (1921) gives little provenance information for his illustrated buckles. Since similar forms served civilian clothing and sword belts, an isolated buckle cannot securely be assigned to armour.

130. Fingerlin traces roller buckles to the mid-thirteenth century, although the earlier forms differ from those on plate armour: Fingerlin (1971), pp. 70–74.

131. The buckle on [ref_arm_4904] PDF is probably late fifteenth-century or later, but its attachment is not original. The crude mounting plate contrasts with the finely made hand defence and partly covers an unused hole. That hole may have held an internal strap or the hinge of a now-lost wrist flap. See Goll (2009), p. 36. The source’s phrase “or early century” lacks a century number.

132. No visible gilding was identified during this study. Chemical examination of buckles may provide further evidence.

133. The buckle references below are selected examples, not an exhaustive list. Further comparisons could include all recorded objects with potentially original buckles.

134. The buckle on [ref_arm_810] PDF may have lost its roller. Although the buckles appear old, their relationship to the armour’s manufacture is uncertain. Different mounting plates on either side indicate reattachment.

135. Ffoulkes (1912), p.78.

136. Berger (2006), p.5, plate A-48.

137. For difficulties in identifying the original use of excavated buckles, see Fingerlin (1971), pp. 12–13; for armour, pp. 186–187.

138. Detailed examination of this suit was not possible. Further access to its buckles and other small fittings would be valuable.

139. Thomas and Gamber classify all straps and buckles as modern: Thomas and Gamber (1976), p. 106. Nevertheless, the rounded single-frame buckle with a decorated mounting plate on elbow defence [ref_arm_533] PDF could be contemporary with the suit.

140. See Thomas and Gamber (1976), pl. 40. The displayed hand defences were subsequently replaced with [ref_arm_1059] PDF [ref_arm_1124] PDF.

141. Copies of Vienna armour buckles were made before 1921, but Dean does not identify the originals concerned: Dean (1921), p. 62.

142. See for example the hydra-crest A2126 of the HJRK.

143. Trapp (1995), p. 55.

144. Brooker (2007), p. 325, together with the wheel lock gun RG73.

145. Capwell (2002).

146. See chapter [Front].

147. Treitzsaurwein (1775), p. 97-98. Translation of the author: Once upon a time the young wise king [Maximillian I.] rode into a fierce fighting and as he put on all his armour and his fencing-armour, his armoury-master wanted to close his main-armour tightly with screws, so no one would open it by a strike. In this moment, the king asked his armoury-master what would be better: If someone had the control in his own hands or if someone else had the control. The master answered: The one who is in control, is the ruler. So the king said: That is why I want to be in control of the armour and I do not want to depend on you if I have to open my armour. I know that you want to do this for my own well, but you do not know that from your unconsidered or unconscious good will a lot of misery might emerge. By this, everyone might understand that this king was a teacher to other kings in concerns of arms and armour.

148. Plates [ref_arm_3437] PDF [ref_arm_3434] PDF may once have been detachable. Unused central internal slots could have served a bolt-and-eye or hook-and-eye connection.

149. Early sixteenth-century images sometimes show breastplates apparently worn without pelvis protection [ref_ill_art_5381] PDF. Type III predominated in German-speaking regions, but I know no surviving contemporary example with a detachable thoracic-to-abdominal joint; the known plates are permanently riveted.

150. The breastplate seen in this video was made by Peter Müller in 2012 after the extant example [ref_arm_3624] PDF.

151. Some Italian front- and backplates have to be put on together as they are connected via hinges.

152. In the Italian system, lateral hinges and buckles secure the torso plates without fastening the centre of the abdominal plate. Buckles at its upper points therefore need not necessarily have been used.

153. Tobias Capwell incorporated this construction into a reproduced suit, probably following Richard de Beauchamp’s effigy [ref_ill_art_5233] PDF (description 1). No corresponding breastplate survives, and the apparent waist gap may instead be a seam between parts of the cast monument.

154. Some Type I shoulder defences may have buckled to the upper arm. Paired holes also permit an original laced attachment at the lower edge [ref_arm_329] PDF.

155. The detachable components of German-system arm defences make the original arrangement difficult to establish. Surviving laced arrangements are modern; their holes may formerly have held rivets [ref_arm_254] PDF.

156. Exceptions include [ref_arm_1060] PDF [ref_arm_1209] PDF and their counterparts. The cuffs associated with [ref_arm_1209] PDF may have been interchanged during restoration. The objects are visibly altered and the flap hinges are missing.

157. Horse-head-protections were usually also padded.

158. At the left counterpart [ref_arm_2370] PDF the leather straps are modern replacements.

159. Thomas and Gamber (1976), p. 182.

160. A tin coating visible when I photographed the breastplate in 2007 had disappeared by February 2011. The washer is copper alloy; tin could have limited copper corrosion from perspiration and consequent damage to the lining.

161. The holes are now closed with rivets. The breastplate may combine two later Type II plates: comparable holes occur on simple infantry examples [ref_arm_3498] PDF, but not on similarly elaborate objects. Its ridge pattern resembles a backplate, especially where ridges cross from the abdominal to the thoracic plate; compare the associated [ref_arm_3264] PDF, which lacks the small holes. A lining or outer cover would impede the articulated joint. Yet a reconstruction from Type II breastplates also leaves unexplained the absence of waist cut-outs common around 1500.

162. This is especially plausible for [ref_arm_2093] PDF, probably made before 1350, which lacks forehead lining holes. A skull cap still required retention, perhaps straps at the lower edge above the ears or lacing to a padded cap secured under the chin.

163. Maintaining the collection was a Trapp family tradition: Scalini (1996), p. 17 (German edition).

164. Trapp (1995), p.22-23.

165. Both helmets also have permanent linings, making the purpose of the paired holes uncertain.

166. This is a small heraldic blanket in between the helmet and the crest.

167. In these holes also metal wedges similar to those on e. g. [ref_arm_2121] PDF might have been fixed.

168. Trapp (1995), p. 29.

169. For [ref_arm_3059] PDF see: Trapp (1995), p. 73.

170. A London regulation of 1322 prohibited textile-covered helmets so that workmanship remained visible: Ffoulkes (1912), pp. 169–170.

171. A handover inventory of 1436 from Wiener-Neustadt lists numerous armour objects, including: “…item 15 gancz eisnein [i. e. iron] platten; item ain roten samadtein [i. e. velvet] platten und ain rot samadtein helmlin”. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1883), Reg. 48.

172. For the interpretation of the inscription see: Grönwald (2010), p. 187.

173. Part of the copper-alloy cuff band on the wrist’s inner side was replaced, possibly during use. The replacement is redder, lacks engraving and only crudely imitates the original embossing.

174. The roped copper-alloy wrist ring is missing from this right-hand defence but can be reconstructed from its left counterpart [ref_arm_1278] PDF.

175. Only two small detached segments survive, for the interpretation of the inscription see: Grönwald (2010), p. 187.

176. These objects were not examined directly, so the interpretation is tentative. Excavated with other armour at Cēsis Castle, the separately displayed forearm components [ref_arm_117] PDF probably belong together, judging by hinges, corresponding holes and decorative bands. They may form an associated arm defence with shoulder [ref_arm_879] PDF; shared decoration and find context support that possibility.

177. Depictions show that applied decoration continued on Italian armour after 1460. Verrocchio’s Colleoni monument of 1496 in Venice has relief-decorated bands along many edges. Titian’s helmet [ref_ill_art_5397] PDF has a gilded engraved crest and apparently copper-alloy edges and rivet heads. A closely related helmet [ref_ill_art_5221] PDF differs chiefly in its black surface and visor. An effigy of about 1441, apparently representing an English adaptation of Italian armour, also has decorative bands [ref_ill_art_5265] PDF.

178. Well-known examples with gilded or silvered fittings include Henry VIII’s ensemble, RA II.5, c. 1514, and that of Archduke Karl, later Emperor Karl V, HJRK A109, c. 1514. The dissertation describes both as “Faltenrockharnisch” ensembles made in Augsburg by Konrad Seusenhofer. A further example is the “Blau-goldener Küriß”, HJRK A578, c. 1557, by an anonymous maker, probably in Augsburg. The place attribution and its relationship to the chronology in §4.2.6.3.2 require author review.

179. Lost-wax casting is proposed. Filing the bands from solid stock is possible, but their symmetrical relief makes casting more likely.

180. See discussion below in chapter [New recognitions on marks] and [A suit in the BMA].

181. Mann (1962), p. 13-14.

182. Mann (1962), p. 11 and Edge and Williams (2001), p. 235.

183. Dean (1925), p. 134.

184. Thomas and Gamber (1976), p. 97. Examination of the lower edge could establish whether the present bands replaced earlier fittings or conceal a formerly turned edge.

185. Thomas and Gamber (1976), p. 10. The restorations may date between plans for public display around 1863 and installation in 1889.

186. Tracery is occasionally also found at contemporary arms, like crossbow-winches (in Engl. Literature called “cranequins”) or sword-pommels.

187. Roping on the lowest lames of other Helmschmied objects [ref_arm_3294] PDF [ref_arm_3695] PDF was also flattened. The latter backplate gained another pelvis lame; the inside of the second-lowest still preserves its former roped lower border.

188. See: Goll (2009), p. 46.

189. Thomas and Gamber (1976), p.100.

190. Thomas and Gamber (1976), p. 114-115.

191. A goldsmith or “Rotgießer” specialising in copper-alloy casting probably made these complex fittings. Comparable fifteenth-century goldsmiths’ work includes Sigismund’s drinking horn (Esztergom, Föszékedegyházi Kincstár, acc. no. 1964.18.1,2), whose fleur-de-lys bands resemble the Helmschmied fittings: Takács (2006), pp. 370–371.

192. See discussion below in chapter [New recognitions on marks] and [A suit in the BMA].

193. Fragments of copper-alloy rivets remain in some holes along the right shoulder’s lower edge.

194. I did not handle this breastplate. Gamber (1957), p. 40, states that its lowest lame had applied decoration, removed and flattened when upper-leg plates were added around 1490.

195. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1899), Reg. 18210, calls Maximilian “the young Emperor”. “Thoma” is probably the court armourer of Archduke Sigismund mentioned in Reg. 17972 of the same volume.

196. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1900), Reg. 19193.

197. The crane-mounting myth appears in Olivier’s 1944 film “Henry V”: http://www.youtube.com/watch?feature=player_detailpage&v=3jXFnQUU7yg (10 August 2012). Germany’s “Sendung mit der Maus” repeated it in 1985: http://www.youtube.com/watch?feature=player_detailpage&v=-y4j4QhU2nI (10 August 2012). Dirk Breiding of the MET later challenged it: http://www.youtube.com/watch?v=NqC_squo6X4&feature=player_detailpage (10 August 2012).

198. See chapter [Systems] and [Systems].

199. Blair (1972), p. 189.

200. Repeated polishing has removed some material, but losses of a few tenths of a millimetre are not considered sufficient to alter the broad comparisons here.

201. Too little comparable Type VIII data was available; its examination remains a task for future research.

202. Measurements concern the skull at the edge of its reinforcing overlap. Rear measurements come from the narrow integral tail between Type VI cheek plates; upper frontal measurements concern the face guard.

203. For comparisons of type-I breastplates not enough data was at hand.

204. The measurements of the pelvis-lames were omitted, as many important comparable items lacked these lames.

205. Because Type III abdominal plates are narrow and the thoracic plate covers much of the abdomen, an additional section was measured on the latter.

206. Insufficient data excluded Type I and II backplates from the thickness comparison.

207. No type-III neck-protections could be measured.

208. “Mass production” may overstate medieval or Renaissance standardisation. Even where many examples of a model were made, substantial hand-finishing left differences between individual products.

209. See for example the discussion of the helmet [ref_arm_1710] PDF in chapter [Helmets].

210. Egg (1992).

211. Numerous objects entering the antiquities market during the past two centuries also came from these arsenals.

212. Williams (2003), p. 889.

213. Gardner (1898), p. 14.

214. Karcheski and Richardson assembled extensive evidence on the Rhodes armour: Karcheski and Richardson (2003).

215. Pyhrr (1989).

216. Ffoulkes (1911), pp. 381–382. Hefner-Alteneck (1854), p. 83, pl. 63, places the discovery in the castle cistern and includes imprecise drawings of several helmets.

217. Euboea and Chalcis became part of the newly established Greek state in 1830. Had Ottoman authorities found the armour earlier, it might have been transferred to Istanbul.

218. Buchon (1843), p. 134.

219. Blair (1983); Ffoulkes (1911) and V assilatos (1934).

220. Scalini (1984), p. 3-5.

221. Norman (not dated) and Boccia (not dated).

222. All these texts study the helmets, but not the limb protections stored in the MET, mentioned below.

223. Bashford Dean, MET arms and armour curator from 1906 to 1928, acquired these objects for his private collection around 1920. The MET purchased them after his death in 1928; see Grancsay and Kienbusch (1933). Identifying every Chalcis object requires further research because pieces were supplemented or combined with other originals. Dean (1925) discusses suit [ref_arm_3236] PDF, assembled chiefly from Chalcis material.

224. These are: [ref_arm_1462] PDF [ref_arm_1984] PDF [ref_arm_1988] PDF [ref_arm_1989] PDF [ref_arm_1990] PDF [ref_arm_1991] PDF [ref_arm_1992] PDF [ref_arm_2011] PDF [ref_arm_2022] PDF [ref_arm_2059] PDF [ref_arm_2063] PDF [ref_arm_2072] PDF [ref_arm_2103] PDF [ref_arm_2127] PDF [ref_arm_2144] PDF [ref_arm_2146] PDF (lower plate only) [ref_arm_2167] PDF [ref_arm_4389] PDF [ref_arm_4584] PDF [ref_arm_4617] PDF [ref_arm_5112] PDF.

225. Three helmets elsewhere are attributed to Chalcis: [ref_arm_4389] PDF [ref_arm_4617] PDF [ref_arm_2059] PDF. Another, [ref_arm_2072] PDF, remained for centuries in an Ottoman arsenal. Thousands of objects reached Europe from those stores in 1839–1840: Pyhrr (1989), p. 87. Comparable helmets remained in Istanbul, as Dean’s photographs reproduced by Pyhrr show, so some supposed Chalcis examples may instead come from there. Detached lower plate [ref_arm_2146] PDF could belong to a surviving skull; the source proposes a revised total of eighteen, although the count requires clarification. Lower plates on [ref_arm_4617] PDF [ref_arm_2103] PDF [ref_arm_2059] PDF are modern replacements.

226. The detached MET visors probably came from Chalcis through Dean. Their associated skulls may still survive in Athens.

227. Not all items are from Chalcis, but due to their similarity they belong to this group: [ref_arm_1445] PDF [ref_arm_1446] PDF [ref_arm_1447] PDF [ref_arm_1448] PDF [ref_arm_1449] PDF [ref_arm_1450] PDF [ref_arm_1451] PDF [ref_arm_1452] PDF [ref_arm_1453] PDF [ref_arm_1454] PDF [ref_arm_1455] PDF [ref_arm_1458] PDF [ref_arm_1473] PDF [ref_arm_1474] PDF [ref_arm_1475] PDF [ref_arm_1476] PDF [ref_arm_1477] PDF [ref_arm_1478] PDF [ref_arm_1479] PDF [ref_arm_1480] PDF [ref_arm_1483] PDF [ref_arm_1487] PDF [ref_arm_1588] PDF [ref_arm_1590] PDF [ref_arm_2147] PDF [ref_arm_4408] PDF [ref_arm_4460] PDF.

228. At least one is a converted or re-used older helmet [ref_arm_1453] PDF.

229. Published dates vary widely: early fourteenth century for Type V and late fourteenth for Type II (Vassilatos, pp. 123–133, 136); 1430s–1460s (Boccia, p. 7); 1370–1390 (Scalini, p. 4); broadly mid-fourteenth century to 1470 (Ffoulkes); and about 1310 (Buchon), considered too early here.

230. Martin (1967), p. 60 and Reverseau (1982), p. 22.

231. Giorgio Bini reportedly found [ref_arm_5112] PDF in the Tiber: Blair (1983), p. 14, note 14.

232. Boccia (undated), pp. 10–11, sees eastern and Byzantine influences, particularly in the pointed skulls.

233. Other comparable helmets either lack reliable provenance or are attributed to Chalcis. None can therefore be securely associated with use in the western Mediterranean or central Europe.

234. These are: [ref_arm_1981] PDF [ref_arm_1986] PDF [ref_arm_1993] PDF [ref_arm_2000] PDF [ref_arm_2051] PDF [ref_arm_2073] PDF [ref_arm_2095] PDF [ref_arm_2097] PDF [ref_arm_2098] PDF [ref_arm_2112] PDF [ref_arm_2128] PDF [ref_arm_2129] PDF [ref_arm_2145] PDF [ref_arm_4630] PDF [ref_arm_5126] PDF [ref_arm_2161] PDF [ref_arm_4267] PDF.

235. Helmet [ref_arm_1778] PDF lacks a medial ridge. I could not examine it, but it is visibly restored and assembled from different helmets; see Karcheski and Richardson (2003), p. 9. Its skull may date to about 1500, with earlier components added. Original skulls of the group probably all had a central ridge; the ridge on this helmet’s forehead reinforcement suggests it originally accompanied such a skull.

236. Berbenni (1973).

237. For further information (in Italian language) see: http://www.comune.bienno.bs.it/Pages/Pagine_Generiche/?Id=48864 (24.01.2012).

238. The source locates Beretta’s headquarters from 1526 onwards in Val Trompia, neighbouring the valley containing Bienno. This geographical and company-history statement is retained as the dissertation’s account.

239. On the armourers of Brescia see: Rossi (1972).

240. This should focus on tracking down depictions of these items in contemporary artworks.

241. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1891), Reg. 8511.

242. July the 6th, Augsburg: The city council of Augsburg answers to a letter of Sigmund Gossenprot und Ludwig Hoser: …and [have found within a sealed letter by the Emperor, containing [… a draft and a pattern of a kettlehat, of which we should order a certain number…, from: Jahrbuch der Kunsthistorischen Sammlungen in Wien (1891), Reg. 8523, translated by the author.

243. [ref_arm_3653] PDF [ref_arm_3654] PDF [ref_arm_3655] PDF [ref_arm_3656] PDF [ref_arm_3657] PDF [ref_arm_3660] PDF [ref_arm_3661] PDF [ref_arm_3662] PDF [ref_arm_3663] PDF [ref_arm_3664] PDF [ref_arm_3665] PDF [ref_arm_3666] PDF [ref_arm_3667] PDF [ref_arm_3699] PDF.

244. Wackernagel (1982a), p. 80, fig. 16, illustrates a teaching display on breastplate development, including plain examples numbered 1, 3 and 4.

245. After: Wackernagel (1982a), p. 26.

246. [ref_arm_3491] PDF [ref_arm_3492] PDF [ref_arm_3493] PDF [ref_arm_3494] PDF [ref_arm_3495] PDF [ref_arm_3496] PDF [ref_arm_3497] PDF [ref_arm_3501] PDF [ref_arm_3502] PDF [ref_arm_3503] PDF [ref_arm_3504] PDF [ref_arm_3505] PDF [ref_arm_3506] PDF.

247. Treitzsaurwein (1775), p. 98. Translation by the author: “[… furthermore, the wise-king in his armoury developed a marvelous way for the making of combat-armour for his foot soldiers. In his armoury at one time thirty breastplates and also backplates were embossed. Hence, in his armoury in one year a large number of armour was made for the “Landsknechts” fighting on foot. This is how marvelous and artistic this king has been.” The statement is imprecise. Deep-drawing a stack of thirty breastplates in a single blow would not be feasible. The writer may instead have meant that thirty plates were stamped in one day; see the discussion below.

248. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 738.

249. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 784.

250. The cannonball smith was probably commissioned because experience of forging shot in dies supplied the relevant skills.

251. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 816. Translation by the author: “[… two die-anvils with their core and equipment for the making of backplates and arm defenses, so Conrad Seusenhofer, his armourer to the court, would be able to stamp out all the work that he has to finish.”

252. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1883), Reg. 854. Translation by the author: “[… an anvil as a model for armour-plate.“

253. For further explanations on the modern meaning of the word see: http://www.zeno.org/Lueger- 1904/A/Schabotte?hl=schabotte (20.02.2011).

254. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 1010.

255. Translation by the author (with interpretations of the unclear passages): “Those who make breastplates – one of them makes arm-defenses for the foot soldiers – whenever there is a full week make in the time of his imperial highness except of the hardening and the filing 12 breastplates. For whatever one of them worked on stamped breastplates except of the hardening in his own time he was paid for each breastplate 5 Kreuzer. […]”

256. Egg (1992), p. 317.

257. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 1028. Translation by the author (with interpretations): [… I have organized those busy with the “rough” work and paid by myself for the making of breast- and backplates as follows: Whenever they have finished their regular work and they have their free time they can make breastplates and no matter how many they make after work I pay them 5 Kr. For each. But now they want to have a little bit more. With this organization a lot of breastplates can be made for his imperial highness at low cost. These rough-workers make on a weekly bill after their regular work – sometimes more, sometimes less – enormous 18 breastplates and 5Kr. for each makes a sum of 1.5 gulden rh.” (60 Kreuzer=1 Gulden rh.).]

258. Translation by the author: „Balthis Vischer who forges the pelvis-protections for the breastplates and who has pinned down the breastplates for stamping. He is not paid weekly but only for what he earns more or less a day. Two persons.”

259. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 1028. Translation by the author: “[… Furthermore Conz Teininger who I need for several works in the armoury, for the stamping and the hammering of the breastplates and for other work, also grinding. I pay him for expenses and salary 1 Gulden rh. a week.”

260. Egg (1992), p. 318-321.

261. Böhmer and Wiesflecker (1990-1996), Reg. 3422 (http://regesten.regesta- imperii.de/index.php?uri=1495-05-12_3_0_14_1_0_3428_3422).

262. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1884), Reg. 902.

263. See: http://www.nuernberginfos.de/muehlen-nuernberg/sandmuehle.html (23.12.2012).

264. Grancsay (1932), blue etching pp. 345-346, 668; for deep etching see pp. 668-669.

265. Reitzenstein (1959), p.77.

266. See: http://www.lederpedia.de/lederherstellung/gerbung/saemischgerbung (23.12.2012).

267. Not all modern armour was intended to deceive: some served decorative or scholarly purposes. “Reproduction” is therefore used as the general term here.

268. Mowbray (1967), p. 15.

269. Boeheim (2000), pp. 622–640, surveys twenty-one major European armour collections and additional private holdings. First published in 1890, its list was not updated, although many collections subsequently changed or disappeared. Cripps-Day (1925) demonstrates the early demand for a record of private, dealer and auction sales. A continuing comprehensive register remains desirable. The database developed here can attach successive provenance records to each object, helping reconstruct dispersed collections.

270. Reitzenstein (1969) p. 70.

271. Bäumel (2004), Schöbel and Karpinski (1985) and Schöbel and Schaal (1985).

272. A sixteenth-century illustrated inventory appears in Jahrbuch der Kunsthistorischen Sammlungen in Wien (1889), pp. CCXLII–CCCXXIII, and (1890), pp. CCCLIII–CCCC. Later catalogues include Quintana Lacaci (1987) and Valencia Don Juan (1898).

273. Thomas and Gamber (1976), p.11.

274. Thomas (1981).

275. Thomas and Gamber (1976) pp. 11-12.

276. Luchner (1958).

277. Laking (1903) and Galea and Mintoff (1990).

278. „Zeug“ can be translated as „iron stuff“.

279. For municipal defence organisation and the role of arsenals, see Wackernagel (1982b) and Waissenberger (1977).

280. See: Gamber (1977), p. 40.

281. Vienna’s catalogues provide little detailed provenance. These finer, individually differing objects may have entered later. The 1977 catalogue offers possible origins for only [ref_arm_3744] PDF [ref_arm_1894] PDF, perhaps acquired with other equipment from the wealthy citizen Jörg Strasser’s armoury in 1504: Düriegl (1977), p. 76, no. 49, and p. 84, no. 115.

282. On armour in English churches see: Cripps-Day (1922)

283. Mann (1930) and Mann (1938).

284. See: Museen der Stadt Landshut (2009), p. 145.

285. In his historism castle „Abbotsford“ also Sir Walter Scott had gathered some antique arms and armour.

286. Anstruther (1963), pp. 246-247.

287. For a short note on the Eglinton Tournament see: Watts (1989).

288. Franz I of Erbach-Erbach acquired objects from the Nuremberg, Amberg and Neumarkt arsenals.

289. On the history of the armour coming from Rhodes see: Karcheski and Richardson (2003).

290. On 13 December 2011, Pierre Bergé in Brussels sold part of the Berlin Klingbeil collection, one of Germany’s last major private armour collections.

291. E. g. the Victoria and Albert Museum, The Mittelmoselmuseum Traben-Trabach, The Museo San Lazzaro degli Armeni etc.

292. For example for the Eglinton Tournament of 1839.

293. Schedelmann (1963), p. 100-101.

294. Laking (1920), p. 112.

295. Laking (1920), p. 112-113.

296. Schedelmann (1966), p.15.

297. Laking (1920), p. 120-121.

298. The Ernst Schmidt catalogue, probably first issued around 1910, was reprinted with commentary in Mowbray (1967). Pages 161–168 also reproduce G. Pigeon’s Paris catalogue.

299. Mowbray (1967), p. 7.

300. On one of the images there is to read: „Nachbildungen alter Waffen und Rüstungen aus Stahl u. Schmiedearbeit in alter Behandlung” (Engl.: Replicas of old arms and armour made of steel and smithery in old treatment. Transl. by author) Mowbray (1967), pl. 2, p. 19. The meaning of the sentence is not absolutely clear. The word “Stahl” or “steel” is often used for any kind of material which does not have to be carbon steel suitable for heat treatment. It also remains unclear if “alte Behandlung” or “old treatment” refers only to the smithery or also to the production of the material.

301. See: Mowbray (1967), p. 8-9.

302. Grancsay’s introduction to the Schmidt reprint identifies several sixteenth-century-style reproductions in private collections: Mowbray (1967), pp. 10–11.

303. Gimbel (1904)

304. Mowbray (1967), p. 101, pl. 61. The source note states that the suit’s or its components’ whereabouts are unclear; this conflicts with the location proposed in the main text.

305. See: Mowbray (1967), p. 75, pl. 36.

306. Schedelmann (1963), p. 100-101.

307. Schedelmann reproduces an image of Hugel at work, see: Schedelmann (1964a), p. 51.

308. Hayward (1977), p. 78.

309. Laking (1920), p. 113-116.

310. Watts (1992).

311. Schedelmann (1948).

312. Kroener (1988), p. 98.

313. Schedelmann (1964b), p. 116-117.

314. For the discussion of an electro plated armour-piece see chapter [An electro-plated helmet in Delft].

315. For a comprehensive overview see: Meißner and Doktor (2001).

316. V olger (1873), p. 366.

317. Watts (1992), p. 101.

318. See for example: Potier Echelles (1901), p. 10.

319. Boeheim (2000), p. 584.

320. Edge and Williams (2001), p. 235, 239.

321. Grancsay (1952-53).

322. Müller (1999).

323. E. g. Charles Alexander Baron de Cosson, James Gow Mann, Francis Henry Cripps-Day and Sir Guy Francis Laking.

324. Boeheim (2000), p. 572-581.

325. Unfortunately no company names are quoted.

326. Mowbray (1967), p. 13.

327. Compare: Potier Echelles (1901), p. 28-29.

328. See chapter [The making of rivets].

329. Potier Echelles (1901), p. 13-15.

330. Boeheim (1897-99).

331. Potier Echelles (1918-20), p. 298-299.

332. With what else should the plate have been cut?

333. Grancsay (1932).

334. The comparable display known at the time was the Eglinton equipment in Leeds’s Tournament Galleries. During my research visit in spring 2010, those rooms were closed for refurbishment, preventing examination.

335. Grancsay (1932), p. 47.

336. Grancsay’s emphasis on archaeology overlooks art history, another discipline traditionally concerned with authenticity.

337. Grancsay (1932), p. 47.

338. Schedelmann (1963), (1964a), (1964b), (1965), (1966).

339. Schedelmann (1963).

340. V erhoeven (2007).

341. Piersig (1988).

342. Overman (1851).

343. Charles (1998), p. 497. [Editorial note: the source note begins with the incomplete words “This layered”; their intended connection to the main text requires clarification.]

344. Anonymous (1880), p. 79.

345. For a closer description of the development of the Thomas-Process see: Piersig (1989).

346. Lang et al. (1988), p. 390.

347. Alloy: metallic substance composed of two or more elements, as either a compound or a solution. The components of alloys are ordinarily themselves metals, though carbon, a nonmetal, is an essential constituent of steel, see: Anonymous. Definition of "alloy", Encyclopedia Britannica.

348. Agricola (1977).

349. Johannsen (1925).

350. Mutz (1981), Gut (1986), on the late 19th century techniques for rolling iron plates see: Anonymous (1987).

351. Anonymous (1983).

352. Mutz (1983).

353. Koch et al. (1939), Reg. 5820. (http://regesten.regesta-imperii.de/index.php?uri=1409-05- 27_1_0_10_0_0_5827_5820).

354. Karsten (1816) pp. 601 ff.

355. Karsten uses “Schiefern”, related to “Schiefer” (schist), apparently to describe delamination in layered material. The source cites Rimer et al. (2009), entry 1445, 3), as a dictionary reference; that bibliographic identification requires checking.

356. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1895), Reg. 13651.

357. See: Strauch (1986), p.185. Free translation by the author: “Furthermore he has an iron-hat made of steel. No man on earth ever had such a strong hat.”

358. E.g. see: Böhmer and Wiesflecker (1990-1996), Reg. 13436. (http://regesten.regesta- imperii.de/index.php?uri=1499-06-19_4_0_14_3_2_640_13436).

359. “Wälschi” probably means Italian or French. German “welsch” often denotes Romance-speaking European peoples.

360. Panzer could also mean ring-armour, from: Jahrbuch der Kunsthistorischen Sammlungen in Wien (1899), Reg. 17851.

361. See: Ress (1967), p. 827-829.

362. Böhmer and Wiesflecker (1990-1996), Reg. 11610. (http://regesten.regesta- imperii.de/index.php?uri=1501-03-02_1_0_14_3_1_2642_11610).

363. Exceptions include the entirely copper-alloy hand-defence pair [ref_arm_1263] PDF [ref_arm_1303] PDF and helmet [ref_arm_1414] PDF. Each of [ref_arm_1060] PDF [ref_arm_1079] PDF has a copper-alloy metacarpal lame. Copper-alloy finger-root plates occur on pairs [ref_arm_1059] PDF [ref_arm_1124] PDF, [ref_arm_1074] PDF [ref_arm_1125] PDF, [ref_arm_1142] PDF [ref_arm_1096] PDF, [ref_arm_1208] PDF [ref_arm_1246] PDF, [ref_arm_1207] PDF [ref_arm_1244] PDF, [ref_arm_1245] PDF [ref_arm_1272] PDF, [ref_arm_1209] PDF [ref_arm_1247] PDF, and individual objects [ref_arm_1063] PDF [ref_arm_1066] PDF [ref_arm_1071] PDF [ref_arm_1250] PDF [ref_arm_1129] PDF [ref_arm_4904] PDF. Reproductions with such plates include [ref_arm_1045] PDF [ref_arm_1109] PDF and my Freiburg reconstruction [ref_arm_5111] PDF. The original repeats [ref_arm_1096] PDF in its list.

364. In 1496 Maximilian ordered payment to a locksmith for an iron and sheet-metal chest in his private chamber: Böhmer and Wiesflecker (1990–1996), Reg. 7659, http://regesten.regesta-imperii.de/index.php?uri=1496-11-25_2_0_14_2_0_4009_7659.

365. This is the analysis of the crystal micro-structure of iron and the testing of its hardness.

366. Williams (2003).

367. For further and more detailed explanations on the heat-treating of steel see: Verhoeven (2007).

368. Brepohl (1987), p. 59.

369. Bartl (2005), p. 663-664.

370. V erhoeven (2007), p. 65.

371. The summary on diffusion is extracted from p. 63-70 in V erhoeven (2007).

372. Bartl (2005), p. 664-665.

373. Williams (2003), p. 731 and here chapter [A type-II helmet in the Royal Armouries].

374. Here “metallurgy” encompasses the examination methods discussed, including metallography and hardness testing.

375. For preceding studies on armour usually the unit VPH was used.

376. Craddock (2009), p. 154-156.

377. For more precise measurements, an argon atmosphere and tungsten electrode may be used. Instrument chambers are often too small for whole armour objects, requiring a detached sample.

378. Buchwald and Wivel (1998); Pigott (1989); Rose et al. (1990); Williams (1991).

379. According to: Sperl (2001), p. 8, up to 1 cm3 of sample material would be necessary.

380. Cook et al. (2003), p. 22.

381. For a substantial study of radiocarbon dating of iron and its limitations, see Cook et al. (2003).

382. For sword examination, see Wessel (1995), cited twice in the source. For archaeological applications of micro-CT, see Kastner et al. (2007).

383. For easy-to-understand explanations on the basics of computed-tomography see: Avinash C. Kak (2001).

384. See: Charles (1998), p. 500.

385. See: Charles (1998), p. 498.

386. Espelund (1996), p. 53.

387. Köstler (2006), p. 137.

388. Anonymous (1880), p. 87.

389. See: Anonymous (1880), p. 80, tab.

390. E. g. Anonymous (1880), p. 87.

391. Oppermann (1863), here p. 433-435.

392. Overman (1851), p. 365-366.

393. Smith (2004).

394. Five positions along a 100 mm line across the cuff yielded 225–363 HV: Goll (2009), p. 87.

395. See: Williams (2003), p. 898-902.

396. Edge and Williams (2001), p. 239, exclude a previously associated “tilting socket” from Wallace suit A21 because its metallurgy differed from the other components.

397. Williams (1979).

398. Starley (2004).

399. This person is now the curator of arms and armour in a famous south western Swiss historical museum.

400. Bauer and Demmler (1941).

401. Both monumental brasses in Römhild’s town church were made during the sitters’ lifetimes: Bauer and Demmler (1941), pp. 2–3.

402. Gyngell (1959).

403. E. g. Boeheim (2000), p. 633-680; Nickel (1974), p. 281-311.

404. E. g. Thomas and Gamber (1976); Di Carpegna (1969).

405. For more on the similarities of master-marks on products of different craft-branches see: Goll and Sensfelder (2011).

406. Jahrbuch der Kunsthistorischen Sammlungen in Wien (1900), Reg. 18351. The document does not identify which Freiburg is meant. Breisgau and Üechtland are proposed because other namesakes were then small. The source notes specialist crafts in fifteenth-century Fribourg and calls it a “freie Reichsstadt” from 1477; that political description requires verification. Archival research may clarify armour production in either town.

407. Terjanian (2001).

408. A segmented-armour fragment from Otepää Castle, destroyed in 1396, bears a cross within a ring. It may be an exceptionally early armour mark, but the fragment’s inner and outer sides are uncertain: Rachewiltz (2004), p. 108, pl. 3.

409. See chapter [New recognitions on marks].

410. Many later items in the collection also bear this seal mark.

411. Wackernagel describes several monk-head marks on arms and armour. His new Landwehr-period variant probably refers to the lead seal: Wackernagel (1982a), pp. 28, 187–188.

412. Time constraints prevented systematic checking of later armour for these seals during the storage visit.

413. Wackernagel (1982a), p. 30 + 37.

414. For more details on the “Landwehr” see: http://www.bayern-buergerwehr.de/Geschichtliches.html.

415. Braun published the first partly illustrated catalogue of the Zeughaus: Braun (1866).

416. Wackernagel (1982a), p. 38.

417. In November 2012, I informed Munich Stadtmuseum staff that this helmet belonged to the Zeughaus inventory.

418. I helped identify [ref_arm_1749] PDF, previously considered a wartime loss, and other objects as former Zeughaus holdings.

419. See for example: Reitzenstein (1964), p. 19.

420. Schedelmann (1964a), p. 52-53, fig. 1.

421. The book got lost in World War II.

422. Gamber (1957).

423. Gamber (1977), p. 39.

424. Thomas and Gamber (1976), p. 100.

425. Published by: Richardson (1954), p. 6-7; Gamber (1957), p. 43, 48 and Levkoff and Hearst (2008), p. 20-21.

426. It was bought by the DIA in 1953, see Levkoff and Hearst (2008), p. 20.

427. A November 1950 examination report, written while the suit remained with Hearst, already records these assessments. It also calls the backplate’s pelvis lames replacements: "Backplate authentic, except extension plates at sides and three garde-rein lames (which are apparently old metal, but restorations)". The report does not explain the certainty of this judgement, despite recognising old metal and workmanship consistent with the plate.

428. See: Levkoff and Hearst (2008), p. 21

429. Most of the items of this collection are now part of the collections in the Marksburg (Braubach, Germany).

430. Galerie Fischer (1964), lot 199.

431. Laking (1920), p. 119, fig. 1532.

432. Laking (1920), p. 119.

433. Schedelmann (1964a), p. 52-53, fig. 1.

434. Data taken from the museum-register.

435. See chapters [Type-VII] and [Reproduced ornaments on genuine armour].

436. See the discussion in: Watts (1992), p. 102.

437. The closest comparisons likewise have pointed visors and separately made skulls. Other Type VIII forms generally combine the skull, nape and rear shoulder protection in one plate.

438. Possibly also [ref_arm_1658] PDF, but its unknown location and poor frontal photograph prevent secure classification.

439. Watts (1992), p. 104.

440. Spalding (1981).

441. It was not possible to examine the Leeds head piece and no measurements for comparisons are published yet.

442. Watts (1992), p. 104.

443. Williams (1981).

444. Williams (1981), p. 81-82.

445. Williams (2003), p. 731.

446. See chapter [The making of plates].

447. Spalding (1981), p. 8.

448. See also chapter [Notes on the history of armour reproduction and restoration].

449. Puype (2003).

450. V olger (1873), p. 366.

451. Pierre Bergé & associés (2011), lot nr. 182.

452. Galerie Fischer (1934).

453. The catalogue omits an interior photograph and gives only a comparison in the scarce 1934 sale catalogue. Readers therefore cannot readily compare the marks or assess the attribution independently.

454. The source relies on the HJRK’s inherited Habsburg holdings and an asserted absence of private acquisitions to support authenticity. This is a collection-history argument, not a substitute for object-specific provenance verification.

455. For the basics of this method see: Helfen et al. (2005) and Helfen et al.

456. I thank Lukas Helfen, Elias Hamann, Angelica Cecilia and Daniel Hänschke for generously examining the samples and helping interpret the images.

457. I thank Robert Weis of Hermann Historica, Munich, for donating the object for examination.

458. In these reconstructions, higher-density regions appear brighter and lower-density voxels darker.

459. It was generously provided by the “Real Wrought-iron Company”, Lyndhurst.

460. I thank Achim Wirtz for donating numerous samples and helping me understand manual iron refining.

461. This concern arises from a case involving a rare fifteenth-century breastplate in a Berlin museum. Samples were removed from an internal delamination, but no report was published. A personal email described the conclusion: “We tested the Berlin […] brust quite some time ago and it proved to be modern metal, the sort of thing car-bodies are made out of.” I subsequently examined the object and located the sampling damage; my earlier photographs documented its prior condition. Museum staff informed me that the removal had not been authorised. In my assessment, examining an isolated layer while overlooking the visible delamination did not justify the conclusion. This account rests on personal examination and correspondence, not a published analytical report.

462. Possible comparisons include laminography, metallography and X-ray diffraction. During method development, destructive analysis of the same experimental samples may be necessary to validate non-destructive results.

463. Sperl (2001)

DeutschEnglish
Hintergrund / Background: Matthias Goll · Wien / Vienna, A62